Page 1
User Manual
C400, C300, C200
9052 Long Point • Houston, TX 77055 • 888.827.1675 • [email protected]
www.coolazone.com
Page 2
Transportation Page 3
Installation & Set-Up Page 4
Operating Procedures Page 5-8
Storage Page 8
Care & Cleaning Page 9
Safety Page 10
Parts Page 11
Specications Page 12
Applications Page 13
CE Certicate Page 14
Contact Information Page 15
Product Registration Page 16
Table of Contents
Transportation .........................................
Installation & Set-Up ...............................
Operating Procedures .............................
Storage .......................................................
Care & Cleaning .......................................
Safety ........................................................
Parts ............................................................
Specications ..........................................
Applications ..............................................
CE Certicate ............................................
Contact Information ...............................
Product Registration ...............................
2
www.coolazone.com
Page 3
Transportation
TRANSPORTATION:
When the fan is being transported, avoid any impact or collision, or applying excessive
weight to the unit. Excessive weight could damage the unit under these circumstances.
3
www.coolazone.com
Moving State
Fixed State
Unlocked Caster Locked Caster
Page 4
4
www.coolazone.com
Installation & Set-Up
INSTALLATION:
If the fan is placed close to a wall or other obstacle, keep a distance of 3 feet between the
wall or obstacle and the face of the cooling pads.
When placing the fan, take the following into consideration:
a. Uninterrupted fresh air should be made available to the cooling pad side of the unit.
Please do not use the fan in a closed area.
b. Avoid blocking the air output (front) side of the fan. Cool air released from the unit
should be able to freely circulate within an open area.
c. In order to prevent air from being re-circulated, ensure that the area to be cooled is
properly ventilated.
If you have placed the unit at a location where it is inconvenient to connect the water inlet
to a water source, you may pour clean water into the back of the unit.
A full sump tank supply the necessary water for about 3 hours.
Water Valve
Drain Line
Water Inlet
Electric Cord
Rear / Cooling Pad Side
Front / Fan Side
Page 5
5
www.coolazone.com
Operating Procedures
ADJUSTMENT OF THE WATER FLOW & USER’S POSITION:
When the water ow rst starts, ensure that the spray bar, located above the cooling pads,
is evenly distributing water over the pads at a slow drip. Use the “SPRAY BAR ADJUSTMENT”
valve on the front of the unit to make any water ow adjustments.
When proper adjustments are made, a slow drip should be enough water to keep the pads
soaked. Note that excessive water ow can reduce efciency in air cooling. With proper
adjustment, cooling capacity will be increased.
New pads in the unit require a ‘breaking-in’ period for up to one week, before optimal
efciency can be achieved.
Front / Fan Side
Water Valve
“SPRAY BAR ADJUSTMENT”
Valve Control
Counter Clockwise:
Increases Water Flow
Clockwise:
Decreases Water Flow
Page 6
6
www.coolazone.com
Operating Procedures
Power (Emergency Stop)
To ensure that the fan is functioning normally, rst turn on the power switch. The unit
should make a short beeping sound, and all lights on the control panel should ash
once. “Temperature Display” is now ready for use.
Auto Control
Automatic Start: Push the “AUTO ON/OFF” button. Water pump starts when “AUTO ON
” lights up. A timer counts down from 30 seconds while the pump sprinkles water over
the cooling pads, after 30 seconds the fan automatically starts.
Operation Timer
Each short push on the “SET TIMER” button programs 5 minutes of operating time. Press
the “SET TIMER” button for 3 seconds to program 1 hour of operating time.
After the set operating time has expired, the unit goes into auto shut-down mode
whereby the water pump shuts down, a 15 minute timer is activated, and the fan
continues to blow to dry the cooling pads. When the 15 minute timer is complete, the
unit powers down.
For example, if 4 hours of operating time is required, only 3 hours and 45 minutes is
needed when setting the timer. After the operating timer has expired, the unit will
activate the automatic shut off system.
Automatic Shut Off System
Press the “AUTO ON/OFF” button to manually turn off the fan. When pressed, the unit
will activate the automatic shut-off system whereby the water pump shuts down,
“AUTO OFF ” lights up, a 15 minute timer is activated and the fan continues to blow to
dry the cooling pads. When the 15 minute timer is complete, the unit powers down.
THE AUTO CONTROL SYSTEM:
Page 7
7
www.coolazone.com
Operating Procedures
THE AUTO CONTROL SYSTEM (CONTINUED):
Fan Speed Setting
The C-300 fan offers 5 speeds. The C-200 and C-400 fans each offer 3 different speeds.
The High (HI) and Low (LO) Speed Levels of your particular Cool-A-Zone model will
depend not just on the model, but on the date of manufacturing as well. Consult the
handy chart below to nd your Cool-A-Zone speed specications.
Before switching between speeds, allow the unit to reach the full speed of the current
setting. For example, to switch from “Speed 1” to “Speed 2”, wait until “Speed 1” is at
its full speed, then press the “FAN SPEED SET” button to advance to “Speed 2”. Same
procedure follows for Speeds 3-5.
Manual Control
To Power Up: First turn on the pump, then the fan.
To Shut Off: First shut off the pump, then the fan.
To turn the pump on or off, push the “PUMP ON/OFF” button.
To turn the fan or off, push the “FAN ON/OFF” button.
Turn off the power switch once the pump and motor have stopped.After starting the
automatic operation system, if there is a need to switch the pump or fan on/off, press
the pump or fan on/off button on the Manual Control Panel.
To turn the pump or fan on/off while the automatic operation system is in use, press the
“PUMP ON/OFF” or “FAN ON/OFF” button on the Manual Control Panel.
Turn off the power switch once the pump and motor have stopped.
HIGH (HI) / LOW (LO)
SPEED SETTINGS CHART
YOUR COOL-A-ZONE
WAS MANUFACTURED...
BEFORE
1 JAN 2010
1 JAN 2010
TO
31 DEC 2010
AFTER
1 JAN 2011
YOUR
COOL-A-ZONE
MODEL IS...
C-400
HI - LEVEL 3 HI - LEVEL 1 HI - LEVEL 1
LO - LEVEL 1 LO - LEVEL 3 LO - LEVEL 3
C-300
HI - LEVEL 5 HI - LEVEL 5 HI - LEVEL 1
LO - LEVEL 1 LO - LEVEL 1 LO - LEVEL 5
C-200
HI - LEVEL 1 HI - LEVEL 1 HI - LEVEL 1
LO - LEVEL 3 LO - LEVEL 3 LO - LEVEL 3
Page 8
8
www.coolazone.com
Operating Procedure & Storage
To store the fan
1. Drain and clean the sump tank. Be sure that the pads and sump tank are
completely dry.
2. Roll up and secure the power cord.
3. Store the fan in a dry area.
To drain the sump tank
1. Power down the unit.
2. Bend the drain pipe downward to let water out.
3. After the water has stopped owing, place the drain pipe back into the
holding clamps.
Draining the Sump Tank
Control System & the Fuse Box
Temperature Display
When the power is turned on, the temperature of the air being emitted by the fan will
be displayed here.
Water Low
When the water level in the tank is too low to circulate in the system, the warning will
be shown here. The water pump will automatically shut down if the water level gets
too low.
The unit has two fuses for safety: one for the fan motor and one for the water pump. In
the event the fan or water pump stops working, the fuses should be checked to ensure
they are intact.
In order to access the fuse box, remove the control panel cover. Begin by peeling
the cover off at each of the four corners to expose the screws. Unscrew and remove
the control panel. The fuses will be in plain view. Replace any damaged fuses and
replace the control panel by reversing the steps above. NOTE: UNPLUGGING THE UNIT
WHILE POWERED ON COULD BLOW A FUSE.
OPERATING PROCEDURES (CONTINUED):
Storage
DISCONNECT
POWER
BEFORE
WORKING
WITH THE
FUSE BOX!
Page 9
9
www.coolazone.com
Care and Cleaning
MAINTENANCE:
To inspect the sump tank: disconnect the power cord, drain the sump tank, and remove
the cooling pads. Debris will collect in the sump tank over time. Remove any debris with a
clear cloth or shop vacuum.
To access the cooling pads for inspection and cleaning, remove the metal ap at the top
back of the fan. Begin by tilting out the center pad from the top while lifting it out of the
drain trough. To remove the two sides, pads, rst pull them toward the middle of the unit
until they pass the side retainer. Then continue with the same procedure used to remove
the center pad.
An inlet strainer is located on the bottom of the pump and should be inspected and
cleaned periodically.
Cleaning the Cooling Pads
Please make sure the electric power is turned off and cord disconnected from the outlet.
Removing the cooling pads:
After using the unit for a period of time, the pads should be removed for cleaning. Use
clean water and a brush if necessary to clean the cooling pads. Do not use any soap or
detergent to clean the pads.
Page 10
10
www.coolazone.com
Safety
SAFETY GUIDELINES
Do not attempt to remove the front grill or louvers, or use any tool to insert and touch
the blade while the unit is in operation.
When opening the back side for cleaning, please make sure that the unit is powered
off and the power cord is disconnected from the power source.
Only personnel who are properly trained should undertake electrical/electronic
troubleshooting and repair.
Do not alter or bypass protective interlocks.
Before operating the unit, read and observe all warning labels.
When troubleshooting, make sure the unit is powered off and the power cord is
disconnected from the power source.
Take extra precaution in damp areas to protect yourself from accidental electric
shock.
Before turning the power on, be sure that nothing is obstructing the fan blade.
Do not remove the control panel unless it is necessary to inspect the fuses.
Replace components ONLY with components acquired from Cool-A-Zone or an
authorized dealer.
Do not wear metal frame glasses, metallic necklaces, or any accessories such as rings,
watches, and bracelets while working on electrical equipment.
Page 11
11
www.coolazone.com
Parts
PARTS LISTING
Part # Description Part # Description
01 Fiberglass Housing 17 Buoy Stand
02 Fan Gril 18 Valve
03 Louver 19-20 Inside Pipes
04 Blade 21 Water Level Sensor
05 Motor 22 Drain
06 Director 23 Electric Cord
07 Motor Seat 24 Water Inlet
08-12 Wheels 25 Cooling Pads
13 Control Box 26 Air Filter Mesh
14 Temperature Sensor 27 Water Block
15 Pump 28 Cooling Pads Brace
16 Buoy 29 Water Filter
30 Spray Pipe
Page 12
12
www.coolazone.com
Specications
67 in.
170 cm
Depth:
26 in.
66 cm
42 in.
107 cm
51 in.
130 cm
Depth:
21 in.
53 cm
32 in.
82 cm
77 in.
195 cm
56 in.
142 cm
Depth:
31 in.
80 cm
C-300
Five Speeds
Cooling Capacity 2,500 sq. ft.
Maximum Air Delivery 10,000 CFM
Fan Motor 1/2 HP / 110 V - 1/2 HP / 220V
Pump 0.3 HP / 110V - 0.3HP / 220V
Water Reservoir 23 gallons
Width 42 in. / 107 cm
Height 67 in. / 170 cm
Depth 26 in. / 66 cm
Unit Weight 165 lbs. / 75 kg
Shipping Weight 178 lbs / 81 kg
Est. Units (40’ Container) 50
C-400
Three Speeds
Cooling Capacity 4,000 sq. ft.
Maximum Air Delivery 15,000 CFM
Fan Motor 1 HP / 110 V - 1 HP / 220V
Pump 0.3 HP / 110V - 0.3HP / 220V
Water Reservoir 37 gallons
Width 56 in. / 142 cm
Height 77 in. / 195 cm
Depth 31 in. / 80 cm
Unit Weight 249 lbs. / 113 kg
Shipping Weight 282 lbs / 128 kg
Est. Units (40’ Container) 23
C-200
Three Speeds
Cooling Capacity 2,000 sq. ft.
Maximum Air Delivery 7,500 CFM
Fan Motor 1/3 HP / 110 V - 1/3 HP / 220V
Pump 0.3 HP / 110V - 0.3HP / 220V
Water Reservoir 15 gallons
Width 32 in. / 82 cm
Height 51 in. / 130 cm
Depth 21 in. / 53 cm
Unit Weight 122 lbs. / 55 kg
Shipping Weight 132 lbs / 60 kg
Est. Units (40’ Container) 112
HOT
AIR
COMES IN
COOL
REFRESHING
AIR BLOWS
OUT
Cool-A-Zone’s beltless,
direct-powered
stainless steel fan.
Cool-A-Zone’s water
reservoirs hold up to 37
gallons. With add-on
reservoir capacity, you can
run your Cool-A-Zone longer
without relling!
Cool-A-Zone’s
Evaporative
Pad
Cool-A-Zone’s
Water
Distributor
How Cool-A-Zone Works
Page 13
13
www.coolazone.com
Applications
MAIN FUNCTIONS:
Cool-A-Zone is designed to cool environments where traditional A/C is unavailable or costprohibitive. These units are ideal for warehouses, sporting event sidelines for teams, and
aesthetically designed for use in outdoor patios and outdoor weddings, there are myriad of
uses for Cool-A-Zone, such as (but not limited to):
• Industrial / Warehousing
• Manufacturing & Fabrication Shops
• Agricultural
• Military
• Sports & Recreation
• Special Outdoor Events
• Restaurants & Bars
• Automotive / Aviation
• Home & Patio
• Emergency & Disaster Relief
• OSHA Compliance
Page 14
14
www.coolazone.com
CE Certicate
Page 15
15
www.coolazone.com
Contact Information
ENGINEERED BY CURTISON INTERNATIONAL, INC. in USA
MANUFACTURED EXCLUSIVELY BY:
CHIEF EXECUTIVE INDUSTRIES CORP. IN TAIWAN
DISTRIBUTED EXCLUSIVELY BY:
COOL-A-ZONE
Cool-A-Zone
9052 Long Point Road
Houston, TX 77055
coolazone.com
Toll-Free 888.827.1675
Phone 713.968.9860
Fax 713.513.5279
Page 16
16
www.coolazone.com
MODEL:
____ C400 _____ C300 ____ C200
____ C100 _____ C025
COLOR: ____________________________________
SERIAL NUMBER: ____________________________________________
DATE PURCHASED: __________________________________________
FIRST NAME: __________________________________________
LAST NAME: __________________________________________
COMPANY: __________________________________________
ADDRESS 1: __________________________________________
ADDRESS 2: __________________________________________
CITY: _________________________ STATE: _______ ZIP: _____________
COUNTRY: _________________________
WAYS TO REGISTER YOUR PRODUCT:
1. Fill out the form online: http://www.coolazone.com/product-registration.html
2. Fax this form to Cool-A-Zone at: 713.513.5279
3. Scan and email this form to Cool-A-Zone at: [email protected]
4. Mail this form to:
9052 Long Point
Houston, TX 77055
Product Registration
Page 17
Loading...