Cooktek 606800 Installation Manual

Owner’s Manual
Installation And Operation

USE AND CARE OF COOKTEK UNIVERSAL
THERMAL DELIVERY SYSTEM

MODELS: 606700, 606800

CookTek, Inc.
810 W. Washington Blvd.
Chicago, IL 60607
Tel: [phone]
Fax: [phone]

103158 (Rev.0)

You are about to revolutionize the way the food is delivered. As you read this manual
you will begin to discover all of the benefits the CookTek Universal Thermal Delivery
System* (UTDS) has to offer. We believe you will quickly come to appreciate the new
level of speed, operational ease, and quality that the cordless CookTek UTDS brings
to your delivery business. And we at CookTek are truly proud and happy to bring you
this innovation. The UTDS is intended for use in restaurants that provide delivery and
should be used solely for the purpose of keeping food hot during regular deliveries.

BEFORE USING YOUR UTDS

PLEASE TAKE TIME TO COMPLETE THE FOLLOWING:

• Read the entire Owner’s Manual and Warranty and save it for future reference.

• Be sure to register your UTDS unit(s) by completing and mailing the Consumer
Product Ownership Registration Card.

• Record the serial number of your charger unit on the warranty page of this
booklet and keep it in a safe place.

• If, upon receipt, your unit appears damaged in any way, please note the following:
Before operating your Cooktop, do the following:

Visible Loss Or Damage:

Any visible loss or damage must be noted on the freight bill or express receipt
and signed by the person making the delivery. A claim for damages must be filed
immediately, regardless of extent of damage.

Concealed Loss Or Damage:

If damage is not visible until merchandise is unpacked, notify the transportation
company or carrier immediately, and file a ”concealed damage” claim with the carrier.
This should be done within fifteen (15) days of delivery date. The shipment container
and packing materials must be retained for inspection.

The transportation company assumes full responsibility for the safe delivery upon
acceptance of this shipment. CookTek cannot assume responsibility for damage
or loss incurred in transit. CookTek will, however, provide any assistance and
documentation necessary to support your claim.

To save time before requesting service, check the Troubleshooting chart at the end of
this manual for possible solutions to your problem. It lists causes of minor operating
problems that you can correct yourself without removing the housing or exposing the
internal electronics. Do not, for any reason, attempt to service or open the UTDS
charger. A CookTek authorized service dealer must remove the housing and perform
all service to the internal electronics or you will void the warranty.

OWNER’S MANUAL INSTALLATION AND OPERATION

1

There are certain safeguards that must always be followed whenever the UTDS is used.
To reduce the risk of fire, electrical shock or injury, be sure to read all of the following:

Read and follow all instructions carefully.

• The UTDS charger in the United States is equipped with a three-prong electrical
plug. This three-prong plug is part of a system that will protect you from serious
injury if something goes wrong with the electrical wiring in the charger. Be
sure the three-prong plug is plugged into a matching three-prong socket that’s
properly grounded. WARNING! DO NOT cut or break off the large third prong in
this plug, or change the plug or power cord in any way.

• Make sure that incoming voltage matches unit requirements. A product
identification label on the bottom of the charger specifies the operating voltage,
wattage, current, frequency, and phase of unit. Plugging or wiring the charger
into a power source differing from the unit rating may significantly decrease the
performance or severely damage electronic components.

• Unplug the charger before cleaning. Do not submerge the charger in water.
Do not splash or pour water onto the charger’s control panel or into intake/outlet
vents. Possible shock hazard may result and the unit may be damaged.

• Do not use steel wool or abrasive cleaners on the metal housing or plastic locator
tray surface.

• The UTDS chargers and pellets are intended for use with CookTek designed and
approved delivery bags only. Do not attempt to use unapproved or damaged
delivery bags, trays, or pellets.

• Do not place foreign objects on the charger, or between the delivery bag and
charger. Foreign objects placed on the charger or between the charger and bag,
or inside the bag may overheat and cause damage to the charger and/or bag.

• Do not use any UTDS charger that has a damaged cord or plug. Consult the
warranty statement and follow instructions for service.

• Do not let the UTDS charger cord touch hot surfaces.

• Please do not attempt to open the unit or perform service of any kind. This

product can only be serviced by a CookTek Authorized Service Agent or
designated CookTek personnel. Contact CookTek at [phone] for

service information.

• The charger top may get hot to the touch after hours of continuous use. Use
caution when loading and unloading delivery bags.

• Do not place any objects in the delivery bag while it is on the charger.

Every installation site has different electrical wiring requirement. Because many different
local codes exist, it is the Owner and Installer’s responsibility to comply with ALL
applicable codes. CookTek is not responsible for any consequential damages, either
expressed or implied, as a result of failure to comply with installation requirements.

A dedicated electrical circuit is recommended for EACH UTDS Unit.

OWNER’S MANUAL INSTALLATION AND OPERATION

2