Cooktek 500100 Installation Manual

INSTALLATION · OPERATION

OWNER’S MANUAL

FlashPak PTDS II

Models

500100
500200

CookTek, Inc.

810 W. Washington Blvd.

Chicago, IL 60607 U.S.A.

1-312-563-9600

1-312-432-6220

101552

You are about to revolutionize the way the Pizza Industry delivers pizza. As you
read this booklet you will begin to discover all of the benefits the CookTek
FlashPak Pizza Thermal Delivery System* (PTDS) has to offer. We believe you
will quickly come to appreciate the new level of speed, operational ease, and
quality that the cordless CookTek FlashPak PTDS brings to your delivery business.
And we at CookTek are truly proud and happy to bring you this innovation. The
FlashPak PTDS is intended for use in Pizza Delivery restaurants and should be
used solely for the purpose of keeping pizzas hot during regular deliveries.

BEFORE USING YOUR COOKTEK PTDS

PLEASE TAKE TIME TO COMPLETE THE FOLLOWING:

• Read the entire Owner’s Manual and Warranty and save it for future reference.

• Be sure to register your PTDS unit(s) by completing and mailing the Consumer
Product Ownership Registration Card.

• Record the serial number of your charger unit on the warranty page of this
booklet and keep it in a safe place.

• If, upon receipt, your unit appears damaged in any way, please note the
following:

Visible Loss Or Damage: Any visible loss or damage must be noted on the
freight bill or express receipt and signed by the person making the delivery. A
claim for damages must be filed immediately, regardless of extent of damage.

Concealed Loss Or Damage: If damage is not visible until merchandise is
unpacked, notify the transportation company or carrier immediately, and file a
“concealed damage” claim with the carrier. This should be done within fifteen
(15) days of delivery date. The shipment container and packing materials must
be retained for inspection.

The transportation company assumes full responsibility for the safe delivery upon
acceptance of this shipment. CookTek cannot assume responsibility for damage
or loss incurred in transit. CookTek will, however, provide any assistance and
documentation necessary to support your claim.

To save time before requesting service, check the Troubleshooting chart at the end
of this manual for possible solutions to your problem. It lists causes of minor oper­ating problems that you can correct yourself without removing the housing or
exposing the internal electronics. Do not, for any reason, attempt to service or
open the FlashPak PTDS charger. A CookTek authorized service dealer must
remove the housing and perform all service to the internal electronics or you will
void the warranty.

2

There are certain safeguards that must always be followed whenever the
FlashPak PTDS is used. To reduce the risk of fire, electrical shock or injury,
be sure to read all of the following:

Read and follow all instructions carefully.

• The FlashPak PTDS charger in the United States is equipped with a three-prong
electrical plug. This three-prong plug is part of a system that will protect you
from serious injury if something goes wrong with the electrical wiring in the
charger. Be sure the three-prong plug is plugged into a matching three-prong
socket that’s properly grounded. WARNING! DO NOT cut or break off the
large third prong in this plug, or change the plug or power cord in any way.

• Make sure that incoming voltage matches unit requirements. A product identifi­cation label on the bottom of the charger specifies the operating voltage,
wattage, current, frequency, and phase of unit. Plugging or wiring the charger
into a power source differing from the unit rating may significantly decrease the
performance or severely damage electronic components.

• Unplug the charger before cleaning. Do not submerge the charger in water. Do
not splash or pour water onto the charger’s control panel or into intake/outlet
vents. Possible shock hazard may result and the unit may be damaged.

• Do not use steel wool or abrasive cleaners on the metal housing or plastic
locator tray surface.

• The FlashPak PTDS chargers and pellets are intended for use with CookTek
designed and approved pizza bags only. Do not attempt to use unapproved or
damaged pizza bags, trays, or pellets.

• Do not place foreign objects on the charger, or between the pizza bag and
charger. Foreign objects placed on the charger or between the charger and bag,
or inside the bag may overheat and cause damage to the charger and/or bag.

• Do not use any PTDS charger that has a damaged cord or plug. Consult the
warranty and follow instructions for service.

• Do not let the PTDS charger cord touch hot surfaces.

• Please do not attempt to open the unit or perform service of any kind. This

product can only be serviced by a CookTek Authorized Service Agent or
designated CookTek personnel. Contact CookTek at [phone] for

service information.

• The charger top may get hot to the touch after hours of continuous use. Use
caution when loading and unloading pizza bags.

• Do not place any objects in the pizza bag while it is on the charger.

Every installation site has different electrical wiring requirement. Because many
different local codes exist, it is the Owner and Installer’s responsibility to
comply with ALL applicable codes. CookTek is not responsible for any conse­quential damages, either expressed or implied, as a result of failure to comply with
installation requirements.

A dedicated electrical line is recommended for EACH FlashPak PTDS Unit.

3