Washer Dryer
Speed
Delay
Extra Rinse Intense Dry
Underwear
Temp.
Quick Wash
Spin
Dry
Start/Pause
Air-wash
Off
Pre-wash
Cotton
Synthetic
Wool
Silk
Self Clean
GB
Washer Dryer - Barcode: 5052931258536
IE
WARNING: Read the instructions before using the appliance.
BWD60CL - Version: 01
BWD60CL-C&L-A5 GB-IM-07.indd 1 12/16/13 4:10 PM
[01] x 1 [02] x 1 [03] x 1
[04] x 4 [05] x 2 [06] x 2
Off
Underwear
Speed
Extra Rinse Intense Dry
Delay
BYWDI1216
Pre-wash
Temp.
Cotton
Quick Wash
Synthetic
Spin
Dry
Wool
Start/Pause
Silk
Air-wash
Self Clean
[07] x 1 [08] x 1 [09] x 2
1 : 1
[10] x 8 (3 x 12mm)
[11] x 8 (5 x 12mm)
BWD60CL Washer Dryer
BWD60CL-C&L-A5 GB-IM-07.indd 2 12/16/13 4:10 PM
Let's
get started...
These instructions are for your safety. Please read through them
thoroughly before use and retain them for future reference.
GB
IE
Getting started…
Your product 04
Safety 05
In more detail…
Operation 10
Care and Maintenance 21
Troubleshooting 24
Technical and legal information 29
Recycling and disposal 29
Guarantee 30
CE Declaration of conformity 32
Appendix...
Installation
04
10
33
3
BWD60CL-C&L-A5 GB-IM-07.indd 3 12/16/13 4:10 PM
GB
Your product
IE
BWD60CL Washer Dryer
Your product
Unpacking your appliance
Remove all the packing materials to prevent unsteadiness,
including the polystyrene base. Upon opening the package, water
drops may be seen on the plastic bag and the porthole. This is
Getting started...
normal phenomenon resulting from water tests in the factory.
Description
This diagram may be slightly different from the layout of the washer dryer you
have just purchased due to technical improvements.
Back cover screws
Control panel
Selection knob
Work top
Detergent
distribution drawer
Transportation bolts
Transportation bolts
Drain hose
Drain hose
Water inlet valve
Water inlet valve
Power cord
Power cord
Back cover
Back cover
Filter cover
Door
Installation guide
located at the end of
the guidebook
You will need
4
BWD60CL-C&L-A5 GB-IM-07.indd 4 12/16/13 4:10 PM
BWD60CL Washer Dryer
Safety
Warning
Safety
GB
IE
Your safety is of the utmost importance
to us. Please make sure that you read
this instruction booklet before attempting
to install or use the appliance. If you are
unsure of any of the information contained
in this booklet, please contact Customer
Services.
General safety
Repairs to your appliance must only be
•
carried out by one of their authorised service
engineers. Any attempt by an inexperienced
person to repair the appliance, could result
in injury or damage to your washer dryer or
invalidate the warranty.
Getting started...
If you notice that the mains cable is damaged.
•
The appliance must not be used. The same
applies if you notice that the worktop, control
panel, base area or any part of the cabinet is
damaged. As this could allow access to the
internal components of the machine.
The appliance should be turned off and isolated
•
from the mains supply, before either cleaning or
maintenance work is attempted.
5
BWD60CL-C&L-A5 GB-IM-07.indd 5 12/16/13 4:10 PM
GB
IE
Safety
The mains cable must not be used to pull the
•
BWD60CL Washer Dryer
plug out of the electrical socket. Make sure the
plug is accessible.
Getting started...
• The machine should not be sprayed with water.
The glass of the porthole door may become
•
hot during the higher temperature washing
programmes and when using the drying
programmes.
The machine should be allowed to cool before
•
carrying out an emergency drain or cleaning the
drain lter.
It is possible for small animals to chew either
•
mains cables or water hoses, which could
cause an electric shock hazard.
Installation
The installation instructions contained within
•
this user manual should be followed.
Check that the hose joints and connections are
•
rm and no water can leak. If joints are loose
or there is leakage turn off the water supply
and ret. Do not use the washer dryer until the
hoses are properly tted.
It is obligatory for the completed installation to
•
comply with all relevant building regulations and
local water authority requirements.
6
BWD60CL-C&L-A5 GB-IM-07.indd 6 12/16/13 4:10 PM
BWD60CL Washer Dryer
Installation continued…
Before the rst use of the appliance, we
•
advise that a 90°C wash programme is
Safety
GB
IE
completed, using the ‘self clean’ function.
No garments should be placed inside
the machine; however a small amount of
detergent must be used.
During use
It is recommended that the appliance is
•
unplugged and the water supply is turned off
after the machine is used.
This appliance is only designed to wash & dry
•
normal domestic wash loads. If you use your
washer dryer in any other way or it is incorrectly
used, then the manufacturer accepts no liability
for any damage that might be caused and any
guarantee will be void.
No attempt should be made to alter or modify
•
the specications of this appliance.
Getting started...
The detergents that you place in this appliance
•
should be suitable for automatic washing
machines. With regards to dosage levels, the
detergent manufacturer’s recommendations
should be followed.
You should not wash garments that have been
•
in contact with ammable materials.
Your washer dryer should not be used for dry
•
cleaning.
BWD60CL-C&L-A5 GB-IM-07.indd 7 12/16/13 4:10 PM
7
GB
IE
Safety
If you use either dyes or bleaching agents
•
BWD60CL Washer Dryer
inside this machine, then you should consult
with the manufacturer of these products to
Getting started...
make sure they are suitable for use in your
washer dryer. The manufacturer cannot be held
responsible for any damage that may result.
Do not open the detergent distribution drawer
•
during the wash cycle.
• Do not install the washer dryer directly on to carpet.
• Do not dry unwashed garments in the washer dryer.
Do not attempt to force the washer dryer door
•
open. The door is tted with a self lock device that
will release shortly after the cycle is completed.
Do not stop the washer dryer before the end
•
of the drying cycle. If the drying cycle has to
be interrupted quickly remove all clothes and
spread them out to allow heat to dissipate.
The supply cord cannot be replaced. If the cord
•
is damaged the appliance should be scrapped.
This appliance is not intended for use by
•
persons (including children) with reduced
physical,sensory or mental capabilities, or lack
of experience and knowledge, unless they have
beengiven supervision or instruction concerning
use of the appliance by a person responsible
fortheir safety.
8
BWD60CL-C&L-A5 GB-IM-07.indd 8 12/16/13 4:10 PM
BWD60CL Washer Dryer
During use
If the supply cord is damaged, it must be
•
replaced by the manufacturer, its service
Safety
GB
IE
agentor similarly qualied persons in order
to avoid a hazard.
WARNING: In the appliance enclosure or
•
in the built-in structure, keep ventilation
openings clear of obstruction.
Child safety
Your washer dryer should only be used by
•
adults. You should not allow children in the
area of the machine unsupervised. You should
not let them touch the controls or play with the
appliance.
It could be possible for a child or pet to gain
•
access to the washer dryer through the porthole
door. Therefore please check the drum before
using the appliance.
Getting started...
Any packaging that is removed from the
•
machine should be kept away from children.
All detergents should be kept out of children’s
•
reach in a safe place.
9
BWD60CL-C&L-A5 GB-IM-07.indd 9 12/16/13 4:10 PM
GB
Operation
IE
Product specications
BWD60CL Washer Dryer
• 11 wash programmes
• 1 drying programme
In more detail...
• 6kg wash load
• 3kg dry load
• 1200 rpm maximum spin speed
• LED display
• Delay start timer
• Digital countdown indicator
• Spin and temperature selection
buttons
Energy efciency
Energy rating
Wash performance
Water extraction performance
Drying performance
Control panel
• Child lock
• Stainless steel drum
• Adjustable feet
• Error code failure system
• Overow protection
• Foam protection
• Imbalance control system
• Self-clean function (drum cleaning)
B
A
B
B
HJI
Speed Temp.
Delay Extra RinseIntense Dry
Start/Pause
Underwear
Quick Wash
Spin
Dry
Air Wash
Off
Self Clean
Prewash
Cotton
Synthetic
Wool
Delicate
ABCDEF G
A Detergent drawer F Start/Pause button
B Delay button G Program knob
C Extra rinse button H Wash temp button
D Intense button I Spin speed button
E Dry button J LED display
Note: Not all optional functions are available for every wash
programme.
10
BWD60CL-C&L-A5 GB-IM-07.indd 10 12/16/13 4:10 PM
BWD60CL Washer Dryer
Operation
Detergent drawer
• The drawer contains three compartments:
1: Prewash detergent;
This compartment should have detergent
placed in it only if you are going to select a
wash programme that has a prewash cycle as
part of it.
2: Main wash detergent;
This compartment should have detergent
placed in it (you should also put a water
softening agent in this section, if you use one).
The detergent will be added to the drum at the start of the main wash
programme
3: Fabric softener;
This compartment should be used for liquid conditioners (fabric softener,
starch). They will be added to the wash load during the nal rinse.
2
3
Delay button
• Touch this button lightly, the washer dryer will start operation after a period of
time and the corresponding indicator will go on. The range is 0.5-24 hours;
each touch of this button increases half an hour. After the button is set, press
the Start/Pause button to start countdown of the set time.
GB
IE
In more detail...
1
Extra rinse button
• Press this button, the washer dryer will perform additional rinses. Press the
button once to select one additional rinse. The display will show "P--1". Press
the button repeatedly and the screen will display "P--2" or "P--3'; indicating
two or three additional selected rinses. The "extra rinse light" is activated and
ashes during the performance. "P--1/2/3" is displayed. The light turns off
and the display disappears when the extra rinse ends
Note: Some programmes are not applicable to this function.
Intense button
• Touch this button lightly, the indicator light will be light on. You can increase
the washing time, rinsing times in main wash stage of the selected program,
which is suitable for dirty clothes.
11
BWD60CL-C&L-A5 GB-IM-07.indd 11 12/16/13 4:10 PM
GB
Operation
IE
BWD60CL Washer Dryer
Dry button
• Press the button to select, the dry indicator light will illuminate. The washer
dryer perform drying function only.
In more detail...
Start/Pause button
• When the washer dryer is connected to the power socket and a program is
selected, lightly touch this button to start operation. During a wash cycle,
touch it lightly, operation will stop and the indicator light starts blinking. Touch
it again to resume operation. To cancel a wash program during a wash cycle,
touch his button, when the indicator light start blinking, turning the program
knob to "off", the program will be cancelled.
Program knob
• By turning the knob clockwise/counter-clockwise, the required program can
be selected. There are 11 programs available.
Note: Program off only use to turn off the washer dryer.
Wash temp button
• Touch this button lightly, the washing temperature will be displayed on the
display screen. Select a temperature according to the type of laundry.
Spin speed button
Touch this button lightly to select the desired speed. When a speed is set, it will be
displayed on the display screen.
Note: Different water temperatures and spinning speeds can be set
for different laundries. Wash using the default settings if there is no
special requirement.
LED display
• Information as remaining wash time and error messages will be shown here.
Note: After a wash program is started the display will go on and
the remaining wash time decreases. As the water pressure and
temperature may differ, the remaining time may be adjusted
accordingly. When the laundry is not balanced during spinning, the
12
BWD60CL-C&L-A5 GB-IM-07.indd 12 12/16/13 4:10 PM
time may be automatically prolonged.
BWD60CL Washer Dryer
Preparing the wash cycle
Preparing your garments for washing
• Your washing should be sorted out, according to the fabric
type and the wash care symbol that is printed on the
garment’s wash care label (see separate section
"a selection of wash care symbols").
• Your washing should also be sorted out according
to the degree of soiling.
• Check all pockets on garments to make sure that
they are empty.
• Remove any detachable metal items (badges,
paperclips, safety pins etc).
• Zips should be closed, duvet covers and pillow cases should be buttoned
up and any loose straps should be tied up. This will help to prevent other
garments from getting damaged during the wash.
• Woollens and knitted coloured fabrics should be turned inside out before
being washed in the appliance.
• Small delicate items (tights, baby socks, etc) should be placed in either a
washing net or a zipped pillow case.
• Curtains should be handled with particular care. All plastic hooks or metal
strips must be removed before being washed in the appliance.
Operation
GB
IE
In more detail...
• Coloured items and whites should be washed
in separate wash cycles.
• New garments often contain an excess of dye,
therefore it is advisable to wash them separately for their rst wash.
• Garments should be unfolded and shook out before being placed inside the
machine.
13
BWD60CL-C&L-A5 GB-IM-07.indd 13 12/16/13 4:10 PM
GB
Operation
IE
Program selection
Program modes
BWD60CL Washer Dryer
In more detail...
Program
1 Air Wash
2 Dry -- --
3
Spin -- -- None 1000rpm
Quick
4
wash
5 Underwear -- to 90°C 60°C
6 Prewash -- to 90°C 40°C
7 Cotton -- to 90°C 40°C
Temperature
Maximum
-- -- Cotton fabrics No spin
-- to 30°C 0°C
Preset
2
3
2 3 1
1. Detergent compartment
1
for prewash mode.
2. Detergent compartment.
3. Compartment for softener
and other additives.
Laundry type
3kg maximum No spin
Cotton or
synthetic
Underwear 1000rpm
Cotton fabrics 1000rpm
Cotton fabrics 1000rpm
Preset
spin speed
800rpm
8 Synthetic -- to 60°C 40°C
9 Wool -- to 40°C 0°C
10 Delicate -- to 40°C 0°C
11 Self clean -- to 90°C 90°C
Fast colour
synthetic
Woollen
fabrics
Cotton or
synthetic
None 1000rpm
1000rpm
600rpm
600rpm
Note: Program off only use to turn off the washer dryer.
Yes No Optional
14
BWD60CL-C&L-A5 GB-IM-07.indd 14 12/16/13 4:10 PM
BWD60CL Washer Dryer
Consumption and technical data
Consumption table
Operation
GB
IE
Program
Air Wash 2kg -- 0:30 -- -- --
Dry
Spin
Quick
Wash
Underwear 3kg 60°C 1:51 -- -- --
Prewash 6kg 40°C 2:04 -- -- --
Cotton 6kg 40°C 1:49 -- -- --
*) Cotton 6kg 60°C 3:00 53% 0.91kwh 57L
Synthetic 3kg 40°C 1:10 -- -- --
Wool 2kg --°C 0:45 -- -- --
Delicate 1kg --°C 0:45 -- -- --
Self Clean -- 90°C 1:00 -- -- --
The standard 60°C and 40°C cotton programmes are suitable to clean normally
soiled cotton laundry and they are the most efcient programmes in terms of
combined energy and water consumptions for washing that type of cotton laundry;
The actual water temperature may differ from the declared cycle temperature.
Max.
Temperature
load
3kg -- 2:00 -- -- --
6kg -- 0:12 -- -- --
3kg --°C 0:15 -- -- --
Washing
time
Spin drying
performance
Energy
consumption
Water
consumption
In more detail...
Energy Label Program Settings:
1. Washing "Cotton+60°C+Intense+Max speed"
2. Drying: “Dry”
15
BWD60CL-C&L-A5 GB-IM-07.indd 15 12/16/13 4:10 PM
GB
Operation
IE
Washing methods
Warning
In more detail...
Power supply
• Connect the washer dryer to the power supply
Water connection
This Washer Dryer is for domestic use only. Do not use it for purposes
other than that for which it was designed. Follow the instructions
given on the label of each garment and wash only machine-washable
garments. Do not dry garment that has been cleaned with industrial
chemicals.
(220V to 240V~/50Hz).
BWD60CL Washer Dryer
• Connect the washer dryer to the water supply.
Note: Before use, check for any leaks in the
joints between the tap and the inlet hose by
turning on the tap.
Preparing the laundry
• Sort out clothes according to fabric (cotton,
synthetics, wool or silk) and to how dirty they are.
• Separate white clothes from coloured ones. Wash
new garments rst time by hand to check if they
fade or run.
• Empty pockets (keys, coins, etc.) and remove the
harder decorative objects (e.g. brooches).
Attention!
Small parts (like buttons, etc.), or sharp
(zips & buckles) items may cause damage
16
BWD60CL-C&L-A5 GB-IM-07.indd 16 12/16/13 4:10 PM
to the machine.
BWD60CL Washer Dryer
Washing methods
• Garments without hems, underwear, nely
woven textile such as ne curtains are to be
put into wash bag (it is better not to wash
them in a washer dryer).
• Close zippers and hooks, make sure the
buttons are sewn on tightly and place small
items such as socks, belts, bras, etc. in the
wash bag.
• Unfold large pieces of fabric such as bed
sheets, bedspreads, etc.
• Turn shirts inside out.
Selecting detergent
• The washing efciency and the performance
is determined by the quality of detergent
used. Special non-foaming detergent
produces good washing results. Use
specic detergents for synthetic and woollen
goods. Do not use dry cleaning agents such
as trichloroethylene and similar products.
Operation
GB
IE
In more detail...
Note: Do not add more detergent
than needed. Please follow the usage
recommendation on the detergent
package.
Adding detergent
• Slide out the detergent drawer and put the
required detergent and softening agent
into the corresponding compartments.
Push back the drawer gently. (Refer to the
instructions on the drawer).
17
BWD60CL-C&L-A5 GB-IM-07.indd 17 12/16/13 4:10 PM
GB
Start/Pause
Operation
IE
Washing methods
Caution:
In more detail...
Selecting program
• To get the best washing results,
• For prewash program, detergent should be added to both
compartments 1 and 2. For other programs, do not add detergent to
compartment 1.
• Use liquid detergent according to the instructions on its package. Do
not use liquid detergent if the Prewash mode or "Delay" is selected.
• Do not overuse softener as it may damage articial bres.
an appropriate washing program
should be selected according to
the laundry type. Please turn the
program knob to select the correct
program.
Underwear
Quick Wash
Spin
Dry
Air Wash
Off
Self Clean
BWD60CL Washer Dryer
Prewash
Cotton
Synthetic
Wool
Delicate
Selecting additional functions
• Select the required options. (Refer to the "Control panel" pages 08,09 and
10). Otherwise keep all the buttons deselected. If you wish to dry your
laundry directly after the wash cycle is nished, please press the 'Dry' button.
Changing the spin speed
• Touch this button lightly to select
the desired speed.
Speed Temp.
• The max spin speed is different
according to each program.
Delay Extra Rinse Intense Dry
Changing the washing temperature
• Press and hold down the
temperature button until the
Speed Temp.
desired temperature is selected the
symbol "--" for no water heating.
Delay Extra Rinse Intense Dry
18
BWD60CL-C&L-A5 GB-IM-07.indd 18 12/16/13 4:10 PM
BWD60CL Washer Dryer
Self Clean
Washing methods
Start washing
• When the washer dryer is connected to the
power socket and a program is selected, lightly
touch this button to start operation. During a
wash cycle, touch it lightly, the operation will
pause and the indicator light start blinking.
Touch it again to resume operation. To cancel
a wash program during a wash cycle, turn the
control to off.
• The washer dryer will stop operation
automatically when a washing cycle ends. The
"End" sign will appear on the display. Open the
washer door and take out the laundry.
Note:
• The washer is locked if there is excessive water inside the
appliance. Turn the control to spin to remove water. After removing
the water, turn the control to off. Then start the new operation.
• To save energy, the appliance is off after a period of time if the
operation is not conrmed. Turn the control to off for around 1
minute and start a new operation.
e Dry
Operation
Start/Pause
Underwear
Quick Wash
Spin
Dry
Air Wash
Temp.
GB
IE
In more detail...
After washing
• Turn off the water supply and unplug the power cord. Open the washer door
to prevent formation of moisture and odours. Leave the door open when not
in use.
Drying method
Start drying
• Press the dry button. The moisture in the clothes is sensed automatically.
Press the Start/Pause button to start the drying cycle. The appliance will
switch off once the clothes are dry.
Tips for saving energy
1. Collect clothes for one full wash load.
2. Avoid overloading the washer dryer.
3. Prewash only heavily soiled clothes.
4. Reduce the amount of detergent or choose Express 15' or delicate wash
programs for slightly soiled clothes.
BWD60CL-C&L-A5 GB-IM-07.indd 19 12/16/13 4:10 PM
19
GB
Operation
IE
BWD60CL Washer Dryer
Drying method
5. Choose a proper washing temperature. Modern detergents can wash with
very good result already in lower temperature than 60°C. Only use higher
temperature than 60°C for heavily soiled laundry.
In more detail...
6. Follow the dosage recommendation on the detergent package to avoid using
too much detergent.
Care guide
20
Machine
wash, COLD
Machine
wash, WARM
Machine
wash, HOT
Machine
wash, COLD
Permanent
press
Machine
wash, WARM
Permanent
press
Machine
wash, HOT
Permanent
press
Machine
wash, COLD
Gentle cycle
Machine
wash, WARM
Gentle cycle
Machine
wash, HOT
Gentle cycle
Hand wash Tumble dry,
Do not wash Tumble dry,
Bleach as
needed
Any bleach
like clorox®,
may be safely
used
Non-chlorine
bleach as
needed
Use only a
colour-safe
bleach, like
®
clorox 2
Do Not Bleach
No bleach
product
should be
used including
detergents
with bleach - or
follow bleach
package test
procedures to
test for bleach
safety.
Wool mark Tumble dry,
NO HEAT
LOW HEAT
Tumble dry,
MEDIUM
Tumble dry,
HIGH
Tumble dry,
permanent
Press, NO
HEAT
Tumble dry,
permanent
Press, LOW
HEAT
Tumble dry,
permanent
Press,
MEDIUM
Tumble dry,
gentle cycle,
NO HEAT
Tumble dry,
gentle cycle,
LOW HEAT
gentle cycle,
MEDIUM
Do not
tumble
dry
Line dry Iron, steam
Drip dry Iron, steam
Dry at Do not iron
Don't dry
clean
Dry on
clothes
hanger
Tumble
dry,
medium
heat
Tumble
dry, low
heat
Don't
tumble
dry
Iron, steam
or dry, with
LOW HEAT
or dry, with
MEDIUM
HEAT
or dry, with
HIGH HEAT
with steam
Do not iron
Dry-clean
may
appear with
additional
letters and/
or lines take
this item to a
professional
drycleaner
Do not dryclean
Dry cleaning
with any
solvent
Dry cleaning
with
pericloride
BWD60CL-C&L-A5 GB-IM-07.indd 20 12/16/13 4:10 PM
BWD60CL Washer Dryer
Operation
Care and maintenance
Load weight reference
Bed sheet (single) Cotton Approximately 800g
Blanket Wool Approximately 3000g
Blended fabric clothes / Approximately 800g
Jackets Cotton Approximately 800g
Jeans / Approximately 800g
Overalls Cotton Approximately 950g
Ladies Pyjamas / Approximately 200g
Shirts / Approximately 300g
Socks Blended fabrics Approximately 50g
T-Shirts Canon Approximately 300g
Underwear Blended fabrics Approximately 70g
Please note
The nal part of a drying cycle is a cooling cycle without heat to ensure that the
dried items are left at a temperature that keeps them undamaged.
GB
IE
In more detail...
Care and maintenance
After washing.
• Turn off the water supply and
pull out mains plug after each
wash. Open the appliance door
to prevent formation of moisture
and odours. If the washer dryer is
left idle for a long period, drain the
water in the machine and replace
the drain hose.
Cleaning the detergent drawer
• Pull out the drawer and press
the blue catch in the conditioner
compartment ush it clean under
the cold tap and replace by
aligning with the machine and
pressing forwards.
21
BWD60CL-C&L-A5 GB-IM-07.indd 21 12/16/13 4:10 PM
GB
Care and maintenance
IE
BWD60CL Washer Dryer
Care and maintenance
Cleaning the machine
• Unplug the machine during cleaning and maintenance. Use a soft cloth
In more detail...
dampened with soap to clean the machine case and rubber components. Do
not use organic chemicals or corrosive solvents.
Cleaning the lter
1. Release the screw then pull out the
bottom cover.
2. Pull out the bail tube that is to the left
of the drain pump lter. Place the end
of the tube into an adequately sized
bowl. Remove the bung from the
end of the tube and drain the water.
1 2
water
tube
container
Reinstall the plug and push the bail
tube back.
3. Remove the lter by turning counter-
clockwise.
4. Flush the lter clean with running water.
5. Replace the lter by turning clockwise
and remount the cover.
3
4
container
water tube cover
filter
Caution!
1. The lter must be in
place, or it may lead to
leakage.
2. Place a container under
the drain pump lter, to
5
collect any excess water
that may come out the
drain pump when the lter
is removed.
Water inlet valve and inlet valve lter
• To prevent blockage to the water
supply by ingress of foreign
substances, clean the water inlet valve
and inlet valve lter regularly.
22
BWD60CL-C&L-A5 GB-IM-07.indd 22 12/16/13 4:10 PM
BWD60CL Washer Dryer
Care and maintenance
Moving the machine
If the machine is to be moved,
replace the transportation
bolts that removed before
installation to prevent damage
as shown below.
1. Remove the back cover.
2. Remove the blanking
plugs.
3. Insert the plastic
stabilisers and the
transportation bolts.
Tighten the bolts with a
spanner.
4. Ret the back cover.
Long periods without operation
• If the washer dryer is left idle
for a long period, pull out
the electrical plug and turn
off the water supply. Open
the washer door to prevent
formation of moisture and
odours while not in use.
Care and maintenance
1
3 4
Speed
Extra Rinse Intense Dry
Delay
GB
IE
In more detail...
2
Off
Underwear
Pre-wash
Temp.
Cotton
Quick Wash
Synthetic
Spin
Dry
Wool
Start/Pause
Silk
Air-wash
Self Clean
Special function codes
• Control panel lock function: Press the "Delay" and the "Extra Rinse" buttons
simultaneously for 3 seconds (a face icon is shown) after starting a program.
It can no longer be changed by operating buttons or knobs. To unlock press
the "Delay" and "Extra Rinse" buttons again for 3 seconds.
• Power-off memory function: In case of abrupt power failure or the need to cut
off the power during a program cycle, the present settings will be saved and
the preset operation will resume when the power is on again.
• To cancel a program
23
BWD60CL-C&L-A5 GB-IM-07.indd 23 12/16/13 4:10 PM
GB
Care and maintenance
IE
Troubleshooting
BWD60CL Washer Dryer
Special function codes
Press the "Start/Pause" button, then switch off the power and the program is
automatically cancelled. Turn the program selector again to choose another
program.
In more detail...
Alarm sound can be cancelled if it is needed. Please follow the instruction as below:
Switch on the washer dryer and turn the program knob to spin cycle, then press
the "Intense" and "Dry" button, hold on for 3 seconds. The "BEEP OFF" will be
displayed on the screen which indicates that alarm sound has been cancelled.
To operate the above steps again so the alarm sound can be recovered and the
display will show "BEEP ON".
Troubleshooting
The following circumstances do not constitute problems. Do not contact the
Service Centre until the problem has been conrmed.
Fault Cause Solution
Washer dryer
fails to operate.
Poor connection to the
power supply.
Check connection to the power
supply.
Power failure. Check the power supply.
The washer door is not
properly closed.
Close the washer door
properly.
Washer dryer
cannot be lled
with water.
Machine has not been
switched on.
The "Start/Pause" button is
not pressed.
Water tap is not turned on. Turn on the water tap.
Water pressure is less than
Make sure the machine is
switched on.
Press the "Start/Pause"
button.
Check water pressure.
0,03 Mpa.
The inlet hose is kinked. Check the inlet hose.
Water supply failure. Ensure there is a water supply.
The program knob is not
Set the program knob properly.
properly set.
The washer door is not
properly closed.
Close the washer door
properly.
The inlet hose lter is blocked. Unblock the inlet hose lter.
24
BWD60CL-C&L-A5 GB-IM-07.indd 24 12/16/13 4:10 PM
BWD60CL Washer Dryer
Troubleshooting
Troubleshooting
Fault Cause Solution
Machine is draining
while being lled.
Drainage failure. Drain hose is blocked. Unblock the drain hose.
Strong vibration
while spinning.
The height of the drain hose
is below 80cm.
Install drain hose within
80-100cm of height.
The drain hose is in water. Make sure the drain hose
is not in water.
Drain hose end is higher
than 100cm above the oor
level.
Make sure the drain hose
end is between 80-100cm
above oor level.
The lter is blocked. Unblock the lter.
Not all transportation bolts
have been removed.
Washer dryer is located on
an uneven surface or is not
level.
Remove all transportation
bolts.
Make sure the washer
dryer is on an even surface
and levelled.
Machine load is over 6 kg. Reduce amount of laundry
in the drum.
GB
IE
In more detail...
Operation stops
before completing
wash cycle.
Operation stop for a
certain period of time.
Excessive foam in
the drum, which
is spilled to the
distribution drawer.
Water or electricity failure. Check the power supply.
The “Start/Pause” button is
pressed.
Washer dryer gives an error
Press the "Start/Pause"
button.
Check display codes.
message.
The detergent is not a lowfoaming type or for hand
Check if your detergent is
appropriate.
wash.
Excessive use of detergent. Reduce amount of
detergent in the distribution
drawer.
The indicated
program duration
changes during the
The program duration will
be adjusted during the cycle
due to external factors.
This is normal and doesn't
affect the functionality.
cycle.
Spinning fails. The machine has been set
drain time before spin.
Wait for a while before
spin.
Unbalance of the laundry. Reposition the laundry or run
a spinning program again.
25
BWD60CL-C&L-A5 GB-IM-07.indd 25 12/16/13 4:10 PM
GB
Troubleshooting
IE
BWD60CL Washer Dryer
Poor wash results
My garments are looking grey and there are limescale deposits present in
the drum of my washer dryer.
• There is not enough detergent being added.
In more detail...
• The incorrect detergent is being used.
• Stains are not being pre-treated.
• The correct wash programme or wash temperature was not selected.
I have followed the advice given above, but my garments are still coming
out with grey stains on them.
• The garments are soiled with oils, ointments or grease. Try using specialist
stain treatments. Rewash the garments ensuring the correct wash
temperature has been selected.
• Fabric conditioner has come into contact with the garments. This could
be due to overlling the fabric conditioner compartment. If this happens
try to wash out these stains as quickly as you can and try to avoid getting
conditioner on the garments in future.
After the nal rinse, I can still see foam.
• Modern detergents can result in there still being foam in the nal rinse, this
does not mean that the washing is not being rinsed properly.
There is white residue on my garments when I remove them from the
appliance.
• Modern detergents can contain insoluble contents, and white residue after
a wash cycle is not necessarily a sign of the garments not being rinsed
properly.
• You should shake out the garment or brush it off. In future possibly turn the
garment inside out before it is washed. You may wish to move from a powder
detergent and switch to a liquid detergent instead.
Removing stains
Garments that are covered in stains, grease or are heavily soiled may need to be
pre-washed or soaked before being placed inside of the washer dryer.
• Soaking helps to remove protein-type stains, like blood, milk or grass.
• Pre-washing helps to loosen soil before the main wash.
26
BWD60CL-C&L-A5 GB-IM-07.indd 26 12/16/13 4:10 PM
BWD60CL Washer Dryer
Troubleshooting
Poor wash results
Stain removal rules
• Use warm water for soaking or pre-washing stained laundry. Hot water can
set stains.
• Most stains are easier to remove when they are fresh.
• Before treating any stain try to establish; what kind of stain it is, how old the
stain is, what the fabric type is and whether the fabric is colourfast (check the
care label to nd this out).
• Washing and drying can x some stains.
• When bleach is recommended, use a mild fabric bleach that is safe for the
fabric.
• If you need to use a stain remover, put the stained area face down on a
paper towel or white cloth. Apply the stain remover to the back of the stain.
This forces the stain off the fabric, instead of through it.
Stain removal guide
GB
IE
In more detail...
Stain Removal method
Alcoholic
beverages
The stain should be rst washed with cold water, then wiped with
glycerine and water and rinsed with water mixed with vinegar.
The stain should be softly scratched without ruining the material,
Shoe
polish
then rubbed with detergent and rinsed. In case it is not eliminated,
rub with 1 unit of pure alcohol (96 degrees) mixed in 2 units of
water and then washed with lukewarm water.
Stretch the stained area of material on the top of a container and
Tea and
coffee
pour water as hot as the material can endure on it. If the type of
material is suitable, wash it with lye (Do not use lye on coloured
clothes)..
Leave your clothes in cold water and rub with soap or detergent,
Chocolate
and cocoa
wash it in the highest temperature that the material type can
endure. If there is still a stain of oil left, wipe with oxygenated water
(in proportion of 3%).
Tomato
paste
Meat
broth or
egg
Scrape the dried pieces without ruining the material, then leave
in cold water for about 30 minutes and wash by rubbing with
detergent.
Eliminate the dried stain residues and wipe with a sponge or soft
cloth wetted in cold water. Rub with detergent and wash with diluted
lye (Do not use lye on coloured clothes)..
27
BWD60CL-C&L-A5 GB-IM-07.indd 27 12/16/13 4:10 PM
GB
Troubleshooting
IE
Stain removal guide
Stain Removal method
BWD60CL Washer Dryer
Grease
In more detail...
and oil
stains
Mustard
Blood
stain
Cream,
ice cream
and milk
Mould
Ink
Fruit
Grass
stain
First wipe the residues. Rub the stain with detergent and then wash
with lukewarm soapy water.
First apply glycerine to the stained area. Rub with detergent and
then wash. If the stain still does not disappear, wipe with alcohol
(on synthetic and coloured cloth, a mixture of 1 unit alcohol, 2 units
water should be used).
Lay your clothes in cold water for 30 minutes. If the stain still does
not disappear, lay in mixture of water and ammonia (3 table-spoons
of ammonia in 4 litres of water) for 30 minutes.
Lay your clothes in cold water and rub the stained area with
detergent. If the stain has still not disappeared, apply lye on the
fabric of your clothes in proper proportion (Do not use lye on
coloured clothes).
Mould stains should be cleaned as soon as possible. The stain
should be washed with detergent, and if it does not disappear, it
should be wiped with oxygenated water (in proportion of 3%).
Hold the stained area under cold water and wait until the inky water
completely runs off. Then rub with water diluted with lemon juice
and detergent. Wait 5 minutes and then wash.
Stretch the stained area of your clothes on the top part of a
container and pour cold water on it. Do not pour hot water on the
stain. Wipe with cold water and apply glycerine. Wait for 1-2 hours
and rinse after wiping with a few drops of white vinegar.
Rub the stained part with detergent. If the type of fabric is suitable
for use of lye, wash it with lye. Rub your woollen clothes with
alcohol (for coloured one, a mixture of 1 unit pure alcohol and
2 units of water).
Oil paint
The stain should be eliminated before it dries by applying thinner on
it. Then it should be rubbed with detergent and washed.
If your fabric is suitable for the use of lye (Do not use lye on
Burnt
stain
coloured clothes), you can add lye into your washing water. For
woollen fabrics, a cloth dampened in oxygenated water should be
pressed on the stain and it should be ironed with a dry cloth on it. It
should be washed after rinsing well.
28
BWD60CL-C&L-A5 GB-IM-07.indd 28 12/16/13 4:11 PM
BWD60CL Washer Dryer
Technical and legal information
Technical specications
Model number BWD60CL
Power source 220.240V~/50Hz
Max. working current (A) 10
Water pressure (MPa) 0.03≤P≤1
Nominal load (kg) 6
Spinning speed (r/min) 1200
Washing programs 11
Drying programs 1
Max power (W) 2000
Dimensions (H x D x W mm) 825 x 535 x 595
Net weight (kg) 64
Power consumption of the off-mode (W) 0.48
Power consumption of the left-on (W) 0.48
Dry heating (W) 1400
Dry load (kg) 3
Recycling and disposal
GB
IE
In more detail...
Recycling and disposal
Environmental protection
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer for
recycling advice.
The symbol on the product or its packaging indicates that this
product cannot be treated as normal household waste. This
product must be handed over to an electric and electronic
equipment collection point for recycling.
On ensuring that this product is disposed of correctly, you will help to avoid
possible negative consequences for the environment and public health, which
could occur if this product is not handled correctly. To receive more detailed
information about recycling this product, contact your local government, domestic
waste disposal services or the outlet where the product was bought.
Warning
Before discarding an old appliance, switch off and disconnect it from
the power supply. Cut off and render any plug useless. Cut the cable
off directly behind the appliance to prevent misuse. This should be
undertaken by a competent person. Disable the door lock to make sure
that children cannot get stuck inside the appliance.
29
BWD60CL-C&L-A5 GB-IM-07.indd 29 12/16/13 4:11 PM
GB
Guarantee
IE
BWD60CL Washer Dryer
Guarantee
This appliance is covered by a full manufacturer’s 2 year parts and 2 year labour
guarantee and covers all parts and labour costs associated with the repair of the
In more detail...
appliance in a domestic environment. We will repair any defect that arises due to
faulty materials or workmanship and use genuine manufacturers parts.
All claims must be supported with the original receipt or other reasonable proof of
purchase.
If, during the guarantee period, the appliance becomes irreparable as agreed
by the engineer approved by GAA then we reserve the right, at our discretion, to
exchange the defective product with a replacement appliance at GAA’s sole cost.
If the same product is no longer available an alternative will be offered with the
same functions as the faulty item.
After an appliance has been repaired or replaced any remaining balance of the
GAA guarantee will be valid and any further call outs during this prescribed period
will be covered by GAA on the replacement appliance.
Should any person other than an authorized engineer modify or attempt to repair
the appliance then the warranty will be invalid.
The guarantee applies to the UK mainland, Scotland, Ireland, ROI and France but
is not transferable between EU countries.
This guarantee is non-transferable to any other person or product.
The guarantee is covered by UK law and is in addition to and does not diminish
your legal rights.
Extended parts only warranty
As testimony to our commitment to you as a valued customer of Cooke & Lewis,
we will offer you an additional 3 years parts warranty absolutely free.
If during the extended parts warranty period the appliance fails and it is
considered uneconomical to repair our Customer Service Department will offer
you the opportunity to purchase the same or equivalent model at a discounted
price.
All parts supplied free of charge under the extended warranty must be tted by
our approved engineers and will be subject to a call out charge to t the part.
30
BWD60CL-C&L-A5 GB-IM-07.indd 30 12/16/13 4:11 PM
BWD60CL Washer Dryer
Guarantee
Exclusions to the guarantee
Guarantee
GB
IE
This guarantee does NOT cover:
Appliances that have been damaged or neglected as a result of failure to
store, assemble, install, use or care of the products in accordance with the
manufacturer’s instructions - GAA will not accept responsibility under this
guarantee if a product is damaged or becomes defective due to, misuse, neglect,
wilful or accidental damage or act of god.
Normal wear and tear.
Consumable items such as carbon lters and bulbs.
Claims arising from non-domestic use or commercial environment.
Any gas appliance not tted by a gas safe qualied installer.
If no fault is found then GAA reserves the right to charge for the call out at the going
rate.
In the course of the service work carried out it may be necessary to remove the built
in appliance from its tted position. If the appliance is glued, grouted or tiled in such
a manner that it cannot be removed, it is the responsibility of the customer/installer
to remove and reinstall the appliance to facilitate the repair.
This Guarantee does not affect your statutory rights.
In more detail...
The guarantee is offered by GAA Ltd, 1301-1303 Lu Plaza,
2 Wing Yip St, Kwun Tong, Kowloon, Hong Kong.
Customer Service
To arrange an in guarantee service call, please contact customer services on the
following numbers.
UK & Northern Ireland Republic of Ireland (Eire)
Phone: 0844 800 1128 Phone: 014475261
Email: uksupport@apelson.co.uk
Web: www.myspareparts.co.uk
31
BWD60CL-C&L-A5 GB-IM-07.indd 31 12/16/13 4:11 PM
GB
CE Declaration of Conformity
IE
CE Declaration of Conformity
In more detail...
MANUFACTURER: CATA
BWD60CL Washer Dryer
ADDRESS:
We hereby certify that the mentioned accessory complies with the essential requirements of the
European Directives applicable, including their modifications and the corresponding transpositions
from the national law.
MACHINE APPLICATION:
TYPE :
EC DIRECTIVES APPLIED:
APPLIED HARMONIZED
STANDARDS:
EN 60335-2-25/A2:2006
EN 60335-2-6/A2:2008
EN 60335-1/A13:2008
EN 62233:2008
APPLIED INTERNATIONAL TECHNICAL
STANDARDS AND SPECIFICATIONS: ISO9001.2008
PLACE: Torelló
C/ Ter nº 2, Torelló 08570 - Barcelona (Spain)
BWD60CL
Washer Dryer
Comply with the European Directives 2006/95/CE: LVD and
the 2004/108/CE: EMC
David Sala
Technical Manager
This appliance respects laws of the suppression of radio-interference. The
Manufacturer has a policy of continuous product improvement, it reserves the
right to adapt and carry out any modication considered necessary without prior
warning.
B&Q plc,
Chandlers Ford, Hants,
SO53 3LE United Kingdom
www.diy.com
32
BWD60CL-C&L-A5 GB-IM-07.indd 32 12/16/13 4:11 PM
Installation
535mm
825mm
01
600mm
580mm
868mm
595mm
Appliance dimensions Aperture dimensions
Height: 825mm 868mm
Width: 595mm 600mm
Depth: 535mm 580mm
33
BWD60CL-C&L-A5 GB-IM-07.indd 33 12/16/13 4:11 PM
02
WARNING
THIS INSTALLATION MUST BE COMPLETED BY A
SUITABLY QUALIFIED PERSON. THE MANUFACTURER
ONLY SANCTIONS THE INSTALLATION GIVEN IN
THIS INSTRUCTION MANUAL. YOU SHOULD KEEP
THE TRANSIT PACKAGING, IN CASE YOU NEED TO
TRANSPORT THE MACHINE IN THE FUTURE.
Unpacking the machine and preparing for use.
Note: The bottom cover MUST be installed before
your washer dryer is used for the rst time, AND before
removing the transit bolts.
Lay down the washer dryer on its side and remove the four feet by unscrewing
them.
03
[03] x 1
Place the bottom cover [3] over the bottom of the appliance and align the four
screw holes with the four feet holes. You can then secure the feet back onto the
appliance, thus securing the bottom cover in place.
34
BWD60CL-C&L-A5 GB-IM-07.indd 34 12/16/13 4:11 PM
Removing the transit bolts
Note: The transit bolts MUST be removed before your
washer dryer is used for the rst time.
Remove the four transit bolts from the back of the appliance. The transit bolts stop the
drum from rotating and reduce vibrations during transit.
03
04
03
05
If required, you can remove the back cover of the appliance using a crosshead
screwdriver to assist in removing the transit bolts.
35
BWD60CL-C&L-A5 GB-IM-07.indd 35 12/16/13 4:11 PM
06
[04] x 4
1. Insert the plastic caps (blanking plugs [4]) that are supplied, into the holes
that you have removed the transit bolts from.
2. Keep the transportation bolts in a safe place for future use, should it be
required.
07
Loosen the adjustable feet that are positioned on the base of the appliance.
36
BWD60CL-C&L-A5 GB-IM-07.indd 36 12/16/13 4:11 PM
Positioning and levelling the appliance
Place the washer dryer on a solid and level oor surface.
DO NOT PLACE THE WASHER DRYER ON A CARPET.
Slacken off the lock nut on each of the washer dryer feet using a spanner.
08
09
Adjust the feet to level off the washer dryer.
37
BWD60CL-C&L-A5 GB-IM-07.indd 37 12/16/13 4:11 PM
10
Once levelled correctly, you should tighten the lock nut back up on each of the
washer dryer feet using a spanner.
Important
When the washer dryer is positioned in the location where it will
be used. Make sure that all four feet are resting rmly on the oor,
by pressing down on each corner and checking that the a ppliance
stands still.
11
Take out the attached inlet hose [01].
38
Connecting to the mains water supply
Important
The washer dryer should never be connected to the
water mains using an existing inlet hose, YOU MUST
utilise the inlet hose that is provided with the appliance.
Your appliance should only be connected to a cold water supply.
BWD60CL-C&L-A5 GB-IM-07.indd 38 12/16/13 4:11 PM
Attach the inlet hose [01] vertically to the spiral tap for the washer dryer.
12
[01] x 1
13
Screw the tap tightly in the direction of the screw thread of the inlet hose [01].
39
BWD60CL-C&L-A5 GB-IM-07.indd 39 12/16/13 4:11 PM
14
Connect the hose to the water inlet at the back of the washer dryer.
Important
When connecting the screw thread of the inlet hose and the inlet
valve, prevent the screw thread from being secured incorrectly or it
will wear or leak.
Do not over bend the inlet hose or this will cause damage.
15
40
BWD60CL-C&L-A5 GB-IM-07.indd 40 12/16/13 4:11 PM
Water outlet
Max.
100cm
Min.
80cm
80-100cm
[02]
[02] x 1
Secure the drain hose, so that it cannot move whilst the washer dryer is in use.
Place the end of the drain hose on your drain pipe. Push it a short way down into
your drain pipe.
Caution
Do not insert the drain hose too deeply into the water pipe, as this
may cause siphoning.
NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL
LENGTH.
16
17
[02]
[01]
Alternatively, the drain hose can be connected directly to a sink waste. Ensure the
U bend [02] is secured as high as possible to prevent water owing from the sink
back into the washing machine (xing screw for the U-bend is not supplied).
41
BWD60CL-C&L-A5 GB-IM-07.indd 41 12/16/13 4:11 PM
18
Fitting the furniture door
[05] x 2
[06] x 2
[07] x 1
[09] x 2
[10] x 8
[11] x 8
[10][09]
[11] [06]
[05]
1. Please refer to the building in template for instructions on how to t your
integrated appliance and connect the furniture door to the product.
2. Mount the furniture door to the cabinet of the washer dryer, using the hinges
supplied.
3. Fix the magnet assembly to the front of the washer dryer and the furniture
door.
42
BWD60CL-C&L-A5 GB-IM-07.indd 42 12/16/13 4:11 PM
Connection to a power supply
Warning
As your appliance is a built in product, the electrical
socket must still be accessible once the appliance is
installed.
Consult the rating plate, located on the back of the appliance
BEFORE making the electrical connections. Ensure that the
voltage reaching the plug, is the same as that on the rating plate.
DO NOT REMOVE THE RATING PLATE AS THE INFORMATION
ON IT IS IMPORTANT.
19
The moulded plug that is supplied with the appliance must be placed into an
earthed and insulated socket.
Broken or damaged power leads must only be replaced by a suitably qualied
person. A power lead of a similar type must be used in replacement.
Caution
We do not recommend that this appliance is connected to an
extension lead.
Before rst use maintenance wash
1. When your washer dryer has been correctly installed, we recommend that
you perform a “self-clean” maintenance wash cycle.
2. This will check that all aspects of the installation are correct; it will
also remove any deposits that may have been left on the drum by the
manufacturing process.
3. Select the “Self Clean” wash programme.
4. A small quantity of detergent should be used during this maintenance wash.
BWD60CL-C&L-A5 GB-IM-07.indd 43 12/16/13 4:11 PM
43
GB IE
B&Q plc,
Chandlers Ford, Hants,
SO53 3LE United Kingdom
www.diy.com
BWD60CL-C&L-A5 GB-IM-07.indd 44 12/16/13 4:11 PM
Loading...