Conwin Helium / Hi-Float Adapter User Manual

Helium / Hi-Float™ Adapter

Instruction Sheet

Hi-Float™ Adapter - Set Up

Firmly press-fit connect the

1

Helium/Hi-Float Adapter on to
the outlet of the Hi-Float pump. The
Adapter has a locking ring that will
hold it in place.

Attach the helium line to the fill-

2

ing outlet of a Duplicator 2 infla-

tor or Dual Split-Second Sizer.

Hi-Float™ Adapter - Inflating Instructions

Hold the balloon under the

1

Helium/Hi-Float Adapter with
the silver outlet in the center of the
balloon.

Press the pump to inject the Hi-

2

Float into the body of the bal
loon. Rub the balloon to evenly coat
the inside of the balloon with Hi-Float
– be sure not to get Hi-Float into the
neck of the balloon.

Set the Duplicator 2 or Dual

3

Sizer to the appropriate size set­ting for 11-inch or larger balloons.
Note, if using a Dual Sizer, be sure to
set the inflator mode to operate from
one outlet – not both.

Tap the foot pedal of the

-

3

automatically inflate the balloon to
the perfect size.

ator 2 or Dual Sizer to

Duplic

Place the Hi-Float clip on the

4

stem of the Hi-Float pump. (Clips
are included with the Hi-Float pump.)
See www.Hi-Float.com for Hi-Float
recommendations.

Pinch the neck of the balloon and

4

remove it from the filling outlet.
Wipe off any excess Hi-Float from the
outlet.

Removing the Helium/Hi-Float™ Adapter

To release the Helium/Hi-Float Adapter from the Hi­Float pump press the locking ring do
nails. This will release the Adapter and it will easily slide
off the pump. Be sure to depress the locking ring fully
before pulling the Adapter off the pump.

wn with your finger

Maintenance Tips

Always cover the tip of the Helium/Hi-Float Adapter with the red plastic Hi-

•
Float pump cap when the unit is not in use. This prevents Hi-Float from clogging
the Adapter
stretched over the tip works well.)

• If Hi-Float clogs the Helium/Hi-Float Adapter remove the Adapter from the
pump and flush it with warm water

. (Note, if you misplace the pump c

arm water dissolves dried Hi-Float.

. W

ap, a 5-inch or smaller balloon

Hi-Float™ Power Pump

Instruction Sheet

Hi-Float™ Power Pump - Set Up Tips

• If the balloons are going to be

Connect the Power Pump regulator

1

to a nitrogen or helium cylinder. 2

Follow the instructions on the reverse page to set-up the Helium/Hi-Float Adapter.

Place a large bottle of Ultra
Hi-Float on the holder and

secure in place with the Velcro belt.

Hi-Float™ Power Pump - Operating Instructions

Hook the wire loop under the

3

pump handle. Place the 11-inch
Hi-Float clip on the Hi-Float
pump (included with the Hi­Float pump).

treated and immediately inflated use
the T-4-2 Adapter on a helium cylin­der. Use a wrench to tighten the T-4­2 Adapter to the helium cylinder. The
T-4-2 Adapter will enable two regula­tors to work off one helium cylinder.
Hand-tighten the Power Pump regu­lator and the Duplicator 2 or Dual
Sizer regulator to the T-4-2 Adapter.

• If you’re pre-treating balloons with
Hi-Float to be inflated at a later time,
nitrogen is a more economical gas to
use.

• Follow Hi-Float’s charts and recom­mendations to use the appropriate
amount of Hi-Float in the balloon.

• Visit www.Hi-Float.com to learn
more about working with Hi-Float.

T-4-2 Adapter

Hold the balloon under the

1

Helium/Hi-Float Adapter with
the silver outlet in the center of the
balloon.

Service & Warranty

For assistance with service & repair
issues, or for warranty information,

please visit
or call

ConwinOnline.com,

[phone]

Press the button on the control box

2

to activate the Power Pump. Hold

down button until the pump depresses

. (Consult Balloon Size Chart at right)

fully

Rub the balloon to evenly coat the inside
with Hi-Float. Be sure not to get Hi-Float
into the neck of the balloon.

Online

Projects

Designs

Galleries

...and more!

If pre-treating balloons to be filled with
helium at a later time, skip step 3.

Tap the foot pedal of the

3

Duplicator 2 or Dual Sizer to
automatically inflate the balloon to
the perfect size. Pinch the neck of the
balloon and remove it from the filling
outlet. Wipe off any excess Hi-Float
from the outlet.

Conwin’s Masterpiece Series Videos

These exciting instructional videos
feature the industry's top balloon
artists sharing their secrets of the
trade on everything from the latest
decorating techniques to business
management and marketing skills.
Visit ConwinOnline.com
complete line of educ

Visit www.ConwinOnline.com today!

Balloon Size Chart

1

press button 1 time.

14-inch Balloons

Press button 2 times.

16-inch Balloons

Press button 3 times.

to see our

ational videos.

1-inch Balloons

10292004