Page 1
onfetti Cannon Kit Includes:
C
2 Confetti Cannons
Confetti Cannon
Instruction Sheet
2 100-Ft. Spools of Wire
1 Two-Zone Control Box with 12-Volt Sealed Battery
1 Control Box Battery Charger
1 Cannon Recharge Regulator
1 Carrying Case
Charging the Confetti Cannon
1 2 3 4
View a demonstration of the
Confetti Cannon on Conwin’s
Tools of the Trade DVD
Hand-tight connect the regulator to a helium
or nitrogen cylinder. The cylinder must have
a minimum of 1,000 psi gas pressure to
properly charge the cannon.
5
Cylinder
Pressure
Gauge
Bleed
Valve
Filling
Outlet
Cannon
Recharge
Cannon
Pressure
Gauge
Hose
Loading the Barrel
Make sure the bleed valve on the
regulator is closed before filling the
cannon cylinder.
Slowly open the cylinder valve. The preset
regulator on the filling hose will
automatically recharge the cannon with
the proper amount of gas. The gauge on
the cannon will read approximately 1,000
psi when the cannon is fully charged.
Close the cylinder valve. Open the bleed
valve to release the pressure from the
filling hose. Remove the filling hose from
the cannon. Screw the cap back on the
filling outlet and tighten.
Remove the cap from the filling
outlet on the cannon. The cap has a
bead chain attached to insure that it
doesn’t get misplaced.
Hand-tight connect the filling hose to
the cannon.
Charging the Control Box
Plug the Control Box Batter
Plug the other end into the back of the Control Box to charge it.
Important! Recharge the battery with the Battery Charger for at
least 8 hours prior to use. The battery can be recharged at any level.
y Charger into a 11
0-volt electrical outlet.
1
Screw the barrel on to the
cannon. Remove the cap ring
from the barrel and fill the
barrel with confetti. If using
bundled confetti, be sure to
remove the rubber bands before
placing them in the barrel. To
avoid confetti from clumping, do
not tightly pack the confetti in
the barrel.
2
Use a foil balloon to seal the
barrel. Cut a 6” radius circle out
of a foil balloon (Use a popped
ap balloon). One circle will
or scr
provide two pieces of foil
material. Place one foil circle
over the end of the barrel and
screw the barrel into the cannon
base.
Page 2
Rigging the Cannon
Firing the Cannon
1
1. The rigging mount, located at the bottom of the barrel fits a 1/2” electrical conduit. Place the conduit into the mount
and firmly tighten the thumb screw to secure the cannon in place.
2. The angle of the cannon barrel can be adjusted to achieve different effects. Select the proper angle for the event and
tighten the wing nut to hold the barrel in place. Use a heavy weight at the base of the column. Before loading the
Confetti Cannon with confetti and covering the conduit with balloons, test fire the cannon prior to the event to insure
the column is properly secured. The cannon will kick when fired.
3. Plug the detonator line into the cannon. The 100-foot spool of line is designed to remain on the orange
holder–unwind only the necessary length needed to connect the cannon to the detonator box.
IMPORTANT: Prior to event, always verify that the battery is fully charged. To avoid accidentally firing the cannons, do not plug the wire into the Control Box until
the event is ready to start. Make sure that the lead wire is taped to the ground to prevent potential tripping danger. As a finishing touch, cover the conduit with a
column of balloons.
2
3
Firmly plug the
lead wire into
the cannon.
On cue, push and hold down the
Control Box detonator button until the
cannon has completely fired. For best
results, wait for approximately 2 seconds
between pressing the first and second
button. This will prolong the air time of
the confetti.
Optional Cannon Accessories
Dual Cannon Outlet
The Dual Outlet plugs into the Control Box to fire 2 cannons per zone. Using 2 dual
outlets, up to 4 cannons can be fired.
Conwin #85300
Another Great Special Effect Product From Conwin
Create amazing special effects for:
Weddings, Corporate Events,
Confetti Drops, Parties, etc.
Conwin’s Pneumatic Balloon
Exploders are safe, easy to use, and
are non-electric. Powered by helium
or nitrogen gas, they are perfect for
exploding balloon walls and for
special effects created with confettifilled balloons.
SSeerrvviiccee &&WWaarrrraanntty
For assistance with service & repair
issues, or for warranty information,
please visit
or call
CCoonnwwiinnOOnnlliinnee..ccoomm
((881188))224466..99223333
y
Online
Projects
,
Designs
Galleries
...and more!
Conwin’s
Update Y
A picture is worth a thousand words.
Is your portfolio up to date on the latest?
Conwin’s Portfolio Builder images are
the perfect solution for making winning
presentations to your clients. Thirty-two
photo qualit
the full series.
Deluxe Exploder Kit
Everything you need to create
spectacular exploding balloon effects.
Kit includes: Carrying Case, Compact
Aluminum Cylinder, Automatic
Cylinder Charger, Balloon Exploder
Regulator, Detonator Box, 100-Foot
Air Line, 6 Continual Exploders, 6
Elbow-End Exploders, 6 Connecting
Tees, 6 Connecting Crosses, 6
Connecting Air Line Splices
PPoorrttffoolliioo BBuuiillddeerrss
ortfolio!
our P
y images are available in
04052006
Visit www.ConwinOnline.com today!
Loading...