Converters.TV 796 Operation Manual

Video to DVI 1080p Scaler Box

- ID# 796

Operation Manual

Introduction

Features

Video to DVI 1080p Scaler Box is an upgraded design to convert Standard Definition
Composite Video (CV) and S-Video (SV) signals to High Definition PC and HDTV
resolutions. Maximum output resolutions available are WUXGA and 1080p. With
support for NTSC and PAL video format input, an in-built frame rate conversion
feature from 50Hz to 60Hz ensures glitch-free viewing. The Video to DVI 1080p Scaler
Box has many enhanced features to maximize video performance and is ideal for use
in professional large screen presentations or private home theater applications.

The Video to DVI 1080p Scaler Box DVI output is DVI-I (Integrated). This means that
the output supports both Digital and Analog screens. The link can carry single or dual
link all digital video/data signals on 24 pins, or Analog video/data signals and ground
on 5 pins. This makes the Video to DVI 1080p Scaler Box ideal for use with any
digital/analog video system.

1. Motion adaptive 3D Y/C separation comb filter
( for composite video input )

2. 3D( frame Based ) motion adaptive YNR/CNR noise reduction
( for Y/C video input )

3. Advanced 3D motion adaptive deinterlace

4. Automatic 2：2/3：2 film mode detection

5. Supports 50Hz to 60Hz frame rate conversion

6. Video quality improvement：

DCTI (Digital chroma transient improvement), DLTI (Digital luminance
transient improvement),
Black level extension.

7. Average picture level ( APL ), Automatic contrast limiter ( ACL ) function
supported.

8. OSD menu for picture quality adjustment.

9. Built-in 8-bit DAC for RGB or YPbPr output.

10. Front Panel and IR remote control.

11. Automatic NTSC/PAL video format detection and switching.

Operation
Controls and
Functions

Front Panel

1. Power button and LED indicator:

Press the button once to power on the unit, Press again to power off.
when the unit is powered on, one of the input LEDs will illuminate
depending on your last selection of input source before power off.
The factory default setting for the input is CV (composite video).

The green LED illuminates when composite video is selected.
The Yellow LED illuminates when S-Video is selected.

2. Input select button:

Press the button to select your desired input source between composite
video and S- Video.

3. IR Sensor: Infrared remote control sensor.

4. Menu/Enter: This button serves two purposes.

a. Press the button to bring up OSD main control menu as shown in the
"OSD Operation".
b. To act as a "enter" key to enter sub menu of you selected item or adjust
value of the selected item.
5/6. +/- button: Press the button to move up or down the tick "V" to your
desired parameter. Or after a parameter is selected by pressing
MENU/ENTER button,
press the button to alter the value of your selected parameter.

Rear Panel

1. DC power jack: 5V 2A DC power input.

2. Composite Video: Use a Composite video cable to connect the

composite video output of the source equipment to this composite
video(CV) input of the scaler.

3. S-Video: Use a S-Video cable to connect the S-Video output of the
source video equipment to this " S-Video" input on the back of the video
scaler.
S-Video provides improved performance over composite video and is
recommended over composite.

4. DVI output: The Video to DVI Scaler Box can output a variety of PC and
HDTV progressive resolutions, in both digital and analog format through DVI­I connector.
Digital output: Connect Video to DVI Scaler Box's digital DVI output to the
DVI input of your TV/display unit using a DVI to DVI cable .
Analog output: If you are to use Video to DVI Scaler Box's analog output to
connect to the analog input of your PC or HDTV, you need to use a DVI to
VGA adaptor to pull out analog signal from the DVI-I connector . The DVI to
VGA adaptor is then connect to the VGA input of your display monitor
through a VGA cable if output is PC resolution, or connect to the YPbPr
input of your HDTV through a VGA to YPbPr/3 RCA adaptor cable if output
is HDTV resolution.

Note: DVI to VGA adaptor is not included in the standard package,
and has to order separately.