Control Products UMTVS-BB User Manual

Page 1
116
845.778.5566 Fax: 845.778.7123
www.nicholsonsteamtrap.com
The UMTVS Big Block may be used in conjunction with any two-bolt universal mount steam trap. It combines a universal mount connector block with isolation valves, strainer, blowdown valves and test port to permit fast and easy testing, maintenance, and repair or replacement of a universal mount steam trap.
Integral Strainer and Blowdown Valve
The built-in strainer captures dirt and scale. The blowdown valve at the bottom of the connector block may be used periodically to clean out the strainer.
1st Inlet Isolation Valve (left)
Turning the first isolation valve to the off position (clockwise) stops the flow before it reaches the universal mount stream trap, strainer and blowdown valve. If the first isolation valve is opened (counter-clockwise) flow will be directed through the strainer and blowdown valve ports and to the universal mount steam trap.
Test port (on face)
Condensate exiting the universal mount steam trap is directed to the test port. Fully open the test port by loosening the larger test port valve located on the face of the block (counter-clockwise). This will provide a visual indication of the trap discharge pattern to determine the steam trap functionality.
2nd Outlet Isolation Valve (right)
Turning the second isolation valve to the off position (clockwise) stops the flow to the outlet connection. The flow still may be exhausted through any of the previously mentioned ports. When the second isolation valve is open (counter­clockwise), flow to the outlet connection will continue. Downstream backflow discharge may be observed through the open test port by closing the first Inlet Isolation Valve and blowdown valve and opening the second Outlet Isolation Valve.
BIG BLOCK
UNIVERSAL MOUNT
TRAP VALVE STATION
Pressures to 1440 PSIG (99 bar)
Temperatures to 750°F (399°C)
Compact Size Isolation valves, test ports, strainer
and blowdown valve combined in one Big Block for easy installation.
Universal Mount — Universal two bolt swivel trap mount
installs permanently into system, simplifying installation and removal of trap.
Highest Pressure and Temperature Ratings Suitable
for virtually all applications.
All Stainless Steel — Body, internal wetted parts and
polished inner stem are durable and corrosion resistant.
Blowout Proof Isolation Valves — Feature grease
fittings to lubricate one way Teflon®seals and flush contaminants. Protected from overtorque.
Adjustable Grafoil Packing Simultaneously seals
stem and valve body.
Inner and Outer Valve Stems Reduce wear. Hardened 440 Stainless Steel Ball Tip provides tight
seal and proper alignment.
High Capacity All internal ports at least 1/4".
MODELS*
UMTVS-BB
APPLICA TIONS
Unit Heaters
Steam Tracing
Drip Legs
Heating
Tire Presses
Cooking Equipment
OPERA TION
Laundry Equipment
Plating Tanks
Platent Presses
Refinery
Process
O
PTIONS
SW - Socketweld Connections
CODES
Designed per ASME B16.5, Class 600
Page 2
845.778.5566 Fax: 845.778.7123
www.nicholsonsteamtrap.com
117
Connections: 1/2" & 3/4" NPT or Socketweld
BIG BLOCK
UNIVERSAL MOUNT
TRAP VALVE STATION
SPECIFICATION
Big Block Universal Mount Trap Valve Station shall be a universal mount connector block with integral strainer, blow-down valve, test ports, and dual isolation valves. Body shall be 304L stainless steel. It shall be suitable for pressures to 1440 PSIG. End connections shall be NPT or Socketweld and accommodate connection sizes of 1/2” and 3/4”. It shall function in any orientation. It shall accept universal mount steam traps. The isolation valves shall be bonnetless and blowout proof with a relubrication system.
MAXIMUM O
PERATING CONDITIONS*
Class 600 - 855 psi (59 barg) @ 750ºF (399ºC)
1440 psi (99 barg) @ 100ºF (170ºC)
MATERIALS OF CONSTRUCTION
Body ………………Investment Cast 304L Stainless Steel** Blowdown Valve …………………………304 Stainless Steel Strainer ………………………. 304 Stainless Steel .033 Perf Test Port & Lock Nut………………………303 Stainless Steel Internal Components …………………………Stainless Steel External Seals…………………………………………… Teflon
®
Packing……………………………………………………Grafoil
* Per ASME B16.5, Class 600 ** Per ASTM A351-CF
DIMENSIONS - INCHES (MM)
WEIGHT: 6 LBS. (2.7 KG)
67⁄16
(163)
41⁄
16
(104)
43⁄4
(121)
17⁄8
(47)
31⁄
8
(78)
INLET PORT
OUTLET PORT
Loading...