SERIES D88
VALVE PARTS AND IDENTIFICATION
1/2” - 2-1/2”
3” - 4”
PART NO. PART QTY. MATERIAL
1 Body 1 316L CF3M ASTM 351
2 Pipe Ends 3 316L (CE) ASTM A479
316L (BTE) ASTM A270
316L (BE) ASTM A351
316L (CE) ASTM A351
3 Ball 1 316L
4 Stem 1 316L
5 Valve Seat 2 RTFE / Cavity Filler PTFE / PTFE
6 Valve Seal 2/3 PTFE (3 IN BUTTWELD TUBE EXTENDED)
7 Thrust Bearing 1 Nova*
7A Stem Location
Ring (3” & 4”) 1 Stainless Steel
8 Thrust Bearing 1 Peek
8A Thrust Bearing 1 Nova*
9 Stem Packing 2 Nova*
9A Stem Packing 3 Nova*
(3” & 4”)
10 Seal Protector 1 Peek
11 Gland Packing 1 Stainless Steel
12 Belleville Washer 2 Stainless Steel
* Nova: Carbon and Graphite Filled Teon
PART NO. PART QTY. MATERIAL
13 Packing Nut 1 Stainless Steel
14 Lock Tab 1 Stainless Steel
15 Lower Lock Latch 1 Stainless Steel
15B Upper Lock Latch 1 Stainless Steel
15C Latch Bolt 1 Stainless Steel
16 Handle (1/4”-2”) 1 Stainless Steel
16A Wrench (2-1/2”-4”) 1 Stainless Steel
16B Wrench Block 1 Stainless Steel
16C Hex Head Bolt 1 Stainless Steel
17 Lock Washer 1 Stainless Steel
18 Handle Nut 1/4”-2”) 1 Stainless Steel
19 Body Bolts 4/8 Stainless Steel
1/2”-2-1/2”
19A Body Connector Nut 16/24 Stainless Steel
3”-4”
20 Nuts 4/8 Stainless Steel
21 Stop Pin 1 Stainless Steel
(1/4”-1/2”) 2 Stainless Steel
21A Stopper 1 Stainless Steel
22 Seat 1 Stainless Steel
Retainer
SERIES D88
The dimensions above are for information only, not for construction. For complete actuator mounting dimensions refer to Engineering Bulletin EB-2003.
VALVE PARTS AND IDENTIFICATION
PRESSURE TEMPERATURE DATA
-
1500
1480
-
1400
-
1300
-
1200
-
1100
-
1000
-
900
-
800
720
-
700
-
STEM
ARRANGEMENT
600
-
500
Maximum Pressure PSIG
-
400
-
300
-
200
-
100
100 180 200 300 400 450 500 600 700
-
BOTTOM/
SIDE CENTER USGPM
SIZE A* A1** A2 B J* J1** C D E F G L M N Q R T V O.D. I.D. PORT PORT CV
1/2” 3.50 5.50 2.50 .97 1.70 4.00 1.25 .939 1.00 1.75 1.50 3/8-24 .22 1.76 1.00 4.50 M5 .28 .50 .37 .37 .37 3.2
3/4” 4.00 6.00 2.73 1.05 1.80 4.60 1.50 1.24 1.00 2.05 1.59 3/8 UNF .22 1.87 1.00 4.50 M5 .28 .75 .62 .62 .62 5
1” 4.50 6.50 3.62 1.54 1.95 5.10 1.75 1.51 1.18 2.42 2.19 7/16 UNF .30 2.40 1.18 5.75 M5 .30 1.00 .87 .87 .87 10
1-1/2” 5.50 7.50 4.47 2.13 2.30 5.70 2.25 1.71 1.38 3.16 2.88 9/16 UNF .35 3.16 1.38 7.00 M6 .42 1.50 1.37 1.37 1.37 24
2” 6.28 8.00 4.90 2.66 2.50 5.80 2.62 1.87 1.38 3.56 3.06 9/16 UNF .35 3.35 1.38 7.00 M6 .42 2.00 1.87 1.87 1.87 36
2-1/2” 6.75 10.00 5.86 3.20 2.65 7.75 3.35 2.92 2.75 4.57 4.56 M20 .55 5.58 1.25 10.00 M8 .55 2.50 2.37 2.37 2.37 60
3” 6.75 10.00 6.66 3.96 3.20 8.30 5.50 3.87 3.38 6.44 7.25 1.14 UNS .745 7.25 1.75 13.80 M10 .66 3.00 2.87 2.87 2.87 130
4” 8.25 11.00 8.40 4.75 3.60 9.50 6.97 4.48 3.38 8.12 7.84 1.14 UNS .745 7.84 1.75 22.00 M10 .66 4.00 3.83 3.83 3.83 240
* A & J = TR
** A1 & J1 = XBTE
Delrin
1/4” - 2-1/2” NOVA
1/4” - 2-1/2” Reinforced Teon
1/4” - 2-1/2” Teon
UHMWPE
-
-
-
Maximum Temperature °F
1/4” - 2” PEEK
3” - 4”
NOVA
-
-
-
-
-
FLOW PATTERN
The Diverter Valve is designed to accept media through the bottom or side port and direct the ow to either
of the two outlet ports. Series D88 is available with two different porting congurations.
P1: 90˚ Rotation ow from center to right or left
Flow Left Flow Right
P3: 90˚ Rotation ow from center to right or left.
HORIZONTAL FLOW
Flow Left Flow Right
P4: 180˚ Rotation ow from center to right or left or shut-off position.
Flow Left Flow Through Flow Right
P2: 180˚ Rotation ow from center to
right or left or shut-off position.
Flow Left Shut Off Flow Right
HORIZONTAL FLOW
HOW TO ORDER
VALVE VALVE BODY & BALL & BALL
SIZE SERIES ENDS STEM SEAT SEAL ENDS CONFIG. FINISH OPTIONS
1/2” D88 6-316L 6-316L R = Reinforced Telfon® T = Teon® CE = Clamp P1 1=240 GRIT PP=PURG
3/4” T = Teon® XBTE = Buttweld P2 2=320 GRIT
1” C = Cavity Filler Tube Extended P3 3=240 GRIT EP
1-1/2” BE = Buttweld P4 4=320 GRIT EP
2”
2-1/2”
3”
4”
3 2
1
3/4” D88 6 6 T T 1-XBTE P2 1 PP
2-CE
3-CE
Teon® and Viton® are registered trademarks of E.I. DuPont.
Toll-Free 1-877-7SHARPE
(877) 774-2773
Fax: (708) 562-9250
E-Mail: info@sharpevalves.com
www.sharpevalves.com
A Division of Smith-Cooper International, LLC
Northlake, Illinois 60164 U.S.A.
Due to continuous development of our product range we reserve the right to change the dimensions and information contained in the leaet as required. Rev. 1/09
1260 Garnet Drive
Loading...