Control Products 104L Installation Manual

Download

Page 1

TLP LOW

27/04/16

PROFILE EVAPORATORS

PRODUCT DATA &

INCLUDES RATINGS FOR

INSTALLATION

AIR, ELECTRIC, HOT GAS & WARM FLUID DEFROST

ELECTRICAL POWER: 115/1/60, 208-230/1/60, 208-230/3/60, 460/1/60

Bulletin T30-TLP-PDI-17 1087151

Questions about this product?

Email: evaps@t-rp.com

Call: 1-844-893-3222 x520

CONTENTS

Page

Nomenclature....................................................................................................................

See Page 22 for details

Features & Options...........................................................................................................

Capacity Data...................................................................................................................

Electrical Data..................................................................................................................

Wiring Diagrams - Models with standard PSC motors ....................................................

Wiring Diagrams - Models with optional EC Motors /

Dimensional Data.............................................................................................................

Shipping Weights.............................................................................................................

Recommended Expansion Valve Selections...................................................................

Installation Instructions....................................................................................................

Hot Gas Piping Schematics.............................................................................................

Glycol Fluid Cooler Data..................................................................................................

Service Parts..................................................................................................................

Warranty..........................................................................................................................

Project Information..........................................................................................................

“As Built” Service Parts List.............................................................................................

...............................

2 3

4 - 11 12 - 21 22 - 26

28 29 - 30 31 - 33 34 - 36

BACK

Page 2

NOMENCLATURE

27/04/16

T30-TLP-PDI-17

- 2 -

T LP 3 17 L E - S2 B

T = Trenton

Low Prole Evaporator

Number of Fans Nominal Capacity:

x 1000 @ 10°F TD, Btu/H, R404A

Application Range:

M = Medium to High Temp 6 FPI (10°F to 45°F (-12°C to 7°C) Evap Temp) L = Low Temp 6 FPI (-40°F to 0°F(-40°C to -17°C) Evap Temp) V = Low Temp 4 FPI (-40°F to 0°F (-40°C to -17°C) Evap Temp) W = Fluid Air Cooler (with water or glycol)

STANDARD FEATURES

• Compatable with Low GWP Refrigerants

• Streamlined cabinet style

Generation: B = 2nd

Voltage:

S1 = 115/1/60 (air defrost & hot gas models only) S2 = 208-230/1/60 S4 = 460/1/60 (2 to 6 fan models only) T3 = 208-230/3/60

Defrost*:

A = Air E = Electric T = 3 Pipe Hot Gas w/ Electric Heater Pan

or Warm Fluid w/ Electric Heater Pan for Fluid Air Coolers H = 3 Pipe Hot Gas w/ Hot Gas Loop Pan (optional) G = Reverse Cycle w/ Electric Heater Pan R = Reverse Cycle w/ Hot Gas Loop Pan (optional) * T, H, G, R, available on 2 to 6 fan models only

• PSC Motors

• Proven motor/fan/motor mount design

• High e󰀩ciency and high strength fan guard

• Front access

• Higher capacity

• Compact

• Internally enhanced tubing

• More uniform air ow

• Reverse cycle & 3 pipe hot gas available

• Convenient mounting brackets

• Ample electrical and header compartments

• Lower heater wattage

OPTIONAL FEATURES

• Liquid line solenoid valve wire harness factory

installed

• Schrader valve on suction header

• Positive slope, hinged drain pan

• Central drain connections (approximate)

• Universal drain tting

• Large 3/4” ID (3/4” MPT) drain hole

• Factory installed distributor nozzle

• 460/1/60 PSC motor only

• EC motors with patented SmartSpeed® Technology.

See page 22

• Hot gas loop pan with hot gas defrost models

• Factory installed expansion valve,

solenoid valve and room thermostat

• Wire fan guard

Page 3

CAPACITY DATA - ALL MODELS

27/04/16

T30-TLP-PDI-17

- 3 -

TLP

Medium Temperature Models - Capacity @ 6 F.P.I. *

Medium Temp. Models 104M 106M 107M 209M 211M 214M 317M 320M 423M 426M 532M 639M Number Of Fans 1 1 1 2 2 2 3 3 4 4 5 6

R407A

R407C

R404A

R507

R22

Capacity

BTUH

(WATTS)

Evap

Temp.

25°F

(-4°C)

R134a

Air Flow CFM (L/S) Refrigerant **

Charge

R407A

LB. (KG)

Low Temperature Models - Capacity @ 6 F.P.I. *

Low Temp. Models 104L 105L 106L 207L 209L 211L 314L 317L 419L 422L 527L 631L Number Of Fans 1 1 1 2 2 2 3 3 4 4 5 6

R407A

Capacity

BTUH

(WATTS)

Air Flow CFM (L/S) Refrigerant **

Charge

Evap

Temp.

-20°F

(-29°C)

R407A

R407C

R404A

R507

R22

R134a

LB. (KG)

4090 5230 6460 8170 10450 13300 16200 19000 21900 24700 30400 37100

(1197) (1530) (1891) (2394) (3059) (3895) (4731) (5567) (6403) (7230) (8902) (10830)

3870 4950 6120 7740 9900 12600 15400 18100 20800 23500 28900 35200

(1134) (1449) (1791) (2268) (2898) (3690) (4482) (5274) (6066) (6849) (8433) (10260)

4300 5500 6800 8600 11000 14000 17000 20000 23000 26000 32000 39000

(1260) (1610) (1990) (2520) (3220) (4100) (4980) (5860) (6740) (7610) (9370) (11400)

4090 5230 6460 8170 10500 13300 16200 19000 21900 24700 30400 37100

(1197) (1530) (1891) (2394) (3059) (3895) (4731) (5567) (6403) (7230) (8902) (10830)

3870 4950 6120 7740 9900 12600 15300 18000 20700 23400 28800 35100

(1134) (1449) (1791) (2268) (2898) (3690) (4482) (5274) (6066) (6849) (8433) (10260)

1010

(470)

0.7

(0.3)

3610 4560 5510 7030 8550 10500 13300 16200 18100 20900 25700 29500

(1055) (1340) (1615) (2062) (2508) (3059) (3895) (4731) (5292) (6118) (7515) (8626)

3420 4320 5220 6660 8100 9900 12600 15400 17200 19900 24400 28000

(999) (1269) (1530) (1953) (2376) (2898) (3690) (4482) (5013) (5796) (7119) (8172)

3800 4800 5800 7400 9000 11000 14000 17000 19000 22000 27000 31000

(1110) (1410) (1700) (2170) (2640) (3220) (4100) (4980) (5570) (6440) (7910) (9080)

3610 4560 5510 7030 8550 10500 13300 16200 18100 20900 25700 29500

(1055) (1340) (1615) (2062) (2508) (3059) (3895) (4731) (5292) (6118) (7515) (8626)

3420 4320 5220 6660 8100 9900 12600 15300 17100 19800 24300 27900

(999) (1269) (1530) (1953) (2376) (2898) (3690) (4482) (5013) (5796) (7119) (8172)

1010

(470)

0.7

(0.3)

950

(450)

1.1

(0.5)

950

(450)

1.1

(0.5)

900

(430)

1.5

(0.7)

900

(430)

1.5

(0.7)

2020

(950)

1.3

(0.6)

2020

(950)

1.3

(0.6)

1910

(900)

1.4

(0.6)

1910

(900)

1.4

(0.6)

1800

(850)

2.0

(1.2)

1800

(850)

2.0

(1.2)

2860

(1350)

3.0

(1.4)

2860

(1350)

3.0

(1.4)

2700

(1270)

4.0

(1.8)

2700

(1270)

4.0

(1.8)

3810

(1800)

3.9

(1.8)

3810

(1800)

3.9

(1.8)

60Hz

3600

(1700)

(2.4)

3600

(1700)

(2.4)

(2120)

3.3

(2120)

3.3

4500

6.5

(3.0)

4500

6.5

(3.0)

5400

(2550)

7.8

(3.5)

5400

(2550)

7.8

(3.5)

Low Temperature Models - Capacity @ 4 F.P.I. *

Low Temp. 4 FPI Models 103V 104V 105V 206V 208V 209V 312V 315V 416V 419V 523V 627V Number Of Fans 1 1 1 2 2 2 3 3 4 4 5 6

R407A

R407C

R404A

R507

R22

Capacity

BTUH

(WATTS)

Evap

Temp.

-20°F

(-29°C)

R134a

Air Flow CFM (L/S) Refrigerant **

Charge

Capacities rated using 10°F (5.6°C) TD & 100°F (38°C) liquid temperature. Capacities at other TD within a range of 8 to 15 °F (4.4 to 8.3°C) are directly proportional to TD, or use formula: Capacity = Rated capacity ÷ 10 x TD. For capacities at TD outside of range 8 to 15 °F (4.4 to 8.3°C), or liquid temperature lower than 75°F (24°), consult factory . Capacities for R407A and R407C are based on mean temperature. Mean temperature is the average temperature between the saturated suction temperature and the temperature feeding the evaporator. For dew point ratings, consult factory.

* CAPACITY CORRECTION FACTORS FOR LOW TEMPERATURE UNITS

NO CORRECTION FACTOR REQUIRED FOR MEDIUM TEMP. UNITS

R407A

SATURATED SUCTION TEMPERATURE °F (°C)0 (-17.8)

FACTOR 1.06 1.03 1.0 0.92 0.85

LB. (KG)

2850 3900 4750 6080 7410 8840 11400 14300 15200 18100 21900 25700

(836) (1140) (1397) (1786) (2176) (2584) (3344) (4171) (4456) (5292) (6403) (7515)

2700 3690 4500 5760 7020 8370 10800 13600 14400 17200 20800 24400

(792) (1080) (1323) (1692) (2061) (2448) (3168) (3951) (4221) (5013) (6066) (7119)

3000 4100 5000 6400 7800 9300 12000 15000 16000 19000 23000 27000

(880) (1200) (1470) (1880) (2290) (2720) (3520) (4390) (4690) (5570) (6740) (7910)

2850 3900 4750 6080 7410 8840 11400 14300 15200 18100 21900 25700

(836) (1140) (1397) (1786) (2176) (2584) (3344) (4171) (4456) (5292) (6403) (7515)

2700 3690 4500 5760 7020 8370 10800 13500 14400 17100 20700 24300

(792) (1080) (1323) (1692) (2061) (2448) (3168) (3951) (4221) (5013) (6066) (7119)

1070

(510)

(0.3)

0.7

-10

(23.3)

1010

(480)

1.1

(0.5)

(450)

-20

(-28.9)

950

1.5

(0.7)

2140

(1010)

(0.6)

-30

(-34.4)

1.3

-40

(-40)

2020

(950)

1.4

(0.6)

1910

(900)

2.0

(1.2)

3030

(1430)

3.0

(1.4)

** REFRIGERANT CHARGE CONVERSION FACTORS

R407C R404A

0.99 0.92 0.93 1.02 1.03

2860

(1350)

4.0

(1.8)

4040

(1910)

3.9

(1.8)

R507

3810

(1800)

3.3

(2.4)

R22

4770

(2250)

(3.0)

R134a

6.5

5720

(2700)

7.8

(3.5)

Page 4

ELECTRICAL DATA - 115/1/60

27/04/16

T30-TLP-PDI-17

- 4 -

TLP

AIR DEFROST &

60Hz

HOT GAS DEFROST WITH HOT GAS LOOP PAN MODELS

FAN MOTORS

MODEL

TLP

104MA-S1 * 106MA-S1 * 1 1/15 1.0 100 1.3 15 1/15 1.0 60 1.3 15 107MA-S1 * 1 1/15 1.0 100 1.3 15 1/15 1.0 60 1.3 15

209M#-S1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 211M#-S1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 214M#-S1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 317M#-S1 3 1/15 3.0 300 3.3 15 1/15 3.0 180 3.3 15 320M#-S1 3 1/15 3.0 300 3.3 15 1/15 3.0 180 3.3 15 423M#-S1 4 1/15 4.0 400 4.3 15 1/15 4.0 240 4.3 15 426M#-S1 4 1/15 4.0 400 4.3 15 1/15 4.0 240 4.3 15 532M#-S1 5 1/15 5.0 500 5.3 15 1/15 5.0 300 5.3 15 639M#-S1 6 1/15 6.0 600 6.3 15 1/15 6.0 360 6.3 15

207L†-S1 209L†-S1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 211L†-S1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 314L†-S1 3 1/15 3.0 300 3.3 15 1/15 3.0 180 3.3 15 317L†-S1 3 1/15 3.0 300 3.3 15 1/15 3.0 180 3.3 15 419L†-S1 4 1/15 4.0 400 4.3 15 1/15 4.0 240 4.3 15 422L†-S1 4 1/15 4.0 400 4.3 15 1/15 4.0 240 4.3 15 527L†-S1 5 1/15 5.0 500 5.3 15 1/15 5.0 300 5.3 15 631L†-S1 6 1/15 6.0 500 6.3 15 1/15 6.0 360 6.3 15

206V†-S1 208V†-S1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 209V†-S1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 312V†-S1 3 1/15 3.0 300 3.3 15 1/15 3.0 180 3.3 15 315V†-S1 3 1/15 3.0 300 3.3 15 1/15 3.0 180 3.3 15 416V†-S1 4 1/15 4.0 400 4.3 15 1/15 4.0 240 4.3 15 419V†-S1 4 1/15 4.0 400 4.3 15 1/15 4.0 240 4.3 15 523V†-S1 5 1/15 5.0 500 5.3 15 1/15 5.0 300 5.3 15 627V†-S1 6 1/15 6.0 600 6.3 15 1/15 6.0 360 6.3 15

# = A, H or R. Refer to Nomenclature for details * = H and R available on 2 to 6 fan models only.

† = H or R. Refer to Nomenclature for details

FPI

QTY.

1 1/15 1.0 100 1.3 15 1/15 1.0 60 1.3 15

2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15

FLA

TOTAL

PSC MOTORS EC MOTORS

WATTS

MIN. CIRC.

AMPACITY (A)

MAX. FUSE

(AMPS)

FLA

TOTAL

WATTS

MIN. CIRC.

AMPACITY (A)

MAX. FUSE

(AMPS)

Page 5

ELECTRICAL DATA - 208-230/1/60

27/04/16

T30-TLP-PDI-17

- 5 -

TLP

AIR DEFROST &

60Hz

HOT GAS DEFROST WITH HOT GAS LOOP PAN MODELS

FAN MOTORS

MODEL

TLP

104MA-S2 * 106MA-S2 * 1 1/15 0.5 100 0.6 15 1/15 0.6 60 0.8 15 107MA-S2 * 1 1/15 0.5 100 0.6 15 1/15 0.6 60 0.8 15

209M#-S2 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 211M#-S2 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 214M#-S2 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 317M#-S2 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 320M#-S2 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 423M#-S2 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 426M#-S2 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 532M#-S2 5 1/15 2.5 500 2.6 15 1/15 3.0 300 3.2 15 639M#-S2 6 1/15 3.0 600 3.1 15 1/15 3.6 360 3.8 15

207L†-S2 209L†-S2 2 1/15 1.0 100 1.1 15 1/15 0.6 60 0.75 15 211L†-S2 2 1/15 1.0 100 1.1 15 1/15 0.6 60 0.75 15 314L†-S2 3 1/15 1.5 200 1.6 15 1/15 1.2 120 1.4 15 317L†-S2 3 1/15 1.5 200 1.6 15 1/15 1.2 120 1.4 15 419L†-S2 4 1/15 2.0 200 2.1 15 1/15 1.2 120 1.4 15 422L†-S2 4 1/15 2.0 300 2.1 15 1/15 1.8 180 2.0 15 527L†-S2 5 1/15 2.5 300 2.6 15 1/15 1.8 180 2.0 15 631L†-S2 6 1/15 3.0 400 3.1 15 1/15 2.4 240 2.6 15

206V†-S2 208V†-S2 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 209V†-S2 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 312V†-S2 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 315V†-S2 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 416V†-S2 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 419V†-S2 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 523V†-S2 5 1/15 2.5 500 2.6 15 1/15 3.0 300 3.2 15 627V†-S2 6 1/15 3.0 600 3.1 15 1/15 3.6 360 3.8 15

# = A, H or R. Refer to Nomenclature for details * = H and R available on 2 to 6 fan models only. † = H or R. Refer to Nomenclature for details

FPI

QTY.

1 1/15 0.5 100 0.6 15 1/15 0.6 60 0.8 15

2 1/15 1.0 100 1.1 15 1/15 0.6 60 0.75 15

2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15

FLA

TOTAL

PSC MOTORS EC MOTORS

WATTS

MIN. CIRC.

AMPACITY (A)

MAX. FUSE

(AMPS)

FLA

TOTAL

WATTS

MIN. CIRC.

AMPACITY (A)

MAX. FUSE

(AMPS)

Page 6

ELECTRICAL DATA - 460/1/60

27/04/16

T30-TLP-PDI-17

- 6 -

TLP

AIR DEFROST &

HOT GAS DEFROST WITH HOT GAS LOOP PAN MODELS

FAN MOTORS

MODEL

TLP

209M#-S4 211M#-S4 2 1/15 0.8 200 0.9 15 214M#-S4 2 1/15 0.8 200 0.9 15 317M#-S4 3 1/15 1.2 300 1.3 15 320M#-S4 3 1/15 1.2 300 1.3 15 423M#-S4 4 1/15 1.6 400 1.7 15 426M#-S4 4 1/15 1.6 400 1.7 15 532M#-S4 5 1/15 2.0 500 2.1 15 639M#-S4 6 1/15 2.4 600 2.5 15

207L†-S4 209L†-S4 2 1/15 0.8 200 0.9 15 211L†-S4 2 1/15 0.8 200 0.9 15 314L†-S4 3 1/15 1.2 300 1.3 15 317L†-S4 3 1/15 1.2 300 1.3 15 419L†-S4 4 1/15 1.6 400 1.7 15 422L†-S4 4 1/15 1.6 400 1.7 15 527L†-S4 5 1/15 2.0 500 2.1 15 631L†-S4 6 1/15 2.4 600 2.5 15

206V†-S4 208V†-S4 2 1/15 0.8 200 0.9 15 209V†-S4 2 1/15 0.8 200 0.9 15 312V†-S4 3 1/15 1.2 300 1.3 15 315V†-S4 3 1/15 1.2 300 1.3 15 416V†-S4 4 1/15 1.6 400 1.7 15 419V†-S4 4 1/15 1.6 400 1.7 15 523V†-S4 5 1/15 2.0 500 2.1 15 627V†-S4 6 1/15 2.4 600 2.5 15

# = A, H or R. Refer to Nomenclature for details † = H or R. Refer to Nomenclature for details

FPI

QUANTITY

2 1/15 0.8 200 0.9 15

FLA

TOTAL

PSC MOTORS

WATTS

MIN. CIRC.

AMPACITY (A)

60Hz

MAX. FUSE

(AMPS)

Page 7

ELECTRICAL DATA -

27/04/16

T30-TLP-PDI-17

- 7 -

TLP

208-230/1/60 & 208-230/3/60

60Hz

ELECTRIC DEFROST MODELS

FAN MOTORS DEFROST HEATERS

MODEL

TLP

104ME-* 106ME-* 1 1/15 0.5 100 1.4 15 1/15 0.6 60 0.8 15 1060 4.6 5.8 15 3.0 3.8 15 107ME-* 1 1/15 0.5 100 1.4 15 1/15 0.6 60 0.8 15 1060 4.6 5.8 15 3.0 3.8 15 209ME-* 2 1/15 1.0 200 2.5 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15 211ME-* 2 1/15 1.0 200 2.5 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15 214ME-* 2 1/15 1.0 200 2.5 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15 317ME-* 3 1/15 1.5 300 3.6 15 1/15 1.8 180 2.0 15 2730 11.9 14.8 15 7.7 10 15 320ME-* 3 1/15 1.5 300 3.6 15 1/15 1.8 180 2.0 15 2730 11.9 14.8 15 7.7 10 15 423ME-* 4 1/15 2.0 400 4.7 15 1/15 2.4 240 2.6 15 3560 15.5 19.3 20 10 12 15 426ME-* 4 1/15 2.0 400 4.7 15 1/15 2.4 240 2.6 15 3560 15.5 19.3 20 10 12 15 532ME-* 5 1/15 2.5 500 5.8 15 1/15 3.0 300 3.2 15 4400 19.1 23.9 25 12 15.1 20 639ME-* 6 1/15 3.0 600 6.9 15 1/15 3.6 360 3.8 15 5230 22.7 28.4 30 15 18 20 104LE-* 105LE-* 1 1/15 0.5 100 1.4 15 1/15 0.6 60 0.75 15 1060 4.6 5.8 15 3.0 3.8 15 106LE-* 1 1/15 0.5 100 1.4 15 1/15 0.6 60 0.75 15 1060 4.6 5.8 15 3.0 3.8 15 207LE-* 2 1/15 1.0 200 2.5 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15 209LE-* 2 1/15 1.0 200 2.5 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15 211LE-* 2 1/15 1.0 200 2.5 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15 314LE-* 3 1/15 1.5 300 3.6 15 1/15 1.8 180 2.0 15 2730 11.9 14.8 317LE-* 3 1/15 1.5 300 3.6 15 1/15 1.8 180 2.0 15 2730 11.9 14.8 15 7.7 10 15 419LE-* 4 1/15 2.0 400 4.7 15 1/15 2.4 240 2.6 15 3560 15.5 19.3 20 10 12 15 422LE-* 4 1/15 2.0 400 4.7 15 1/15 2.4 240 2.6 15 3560 15.5 19.3 20 10 12 15 527LE-* 5 1/15 2.5 500 5.8 15 1/15 3.0 300 3.2 15 4400 19.1 23.9 25 12 15.1 20 631LE-* 6 1/15 3.0 600 6.9 15 1/15 3.6 360 3.8 15 5230 22.7 28.4 30 15 18 20 103VE-* 104VE-* 1 1/15 0.5 100 1.4 15 1/15 0.6 60 0.75 15 1060 4.6 5.8 15 3.0 3.8 15 105VE-* 1 1/15 0.5 100 1.4 15 1/15 0.6 60 0.75 15 1060 4.6 5.8 15 3.0 3.8 15 206VE-* 2 1/15 1.0 200 2.5 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15 208VE-* 2 1/15 1.0 200 2.5 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15 209VE-* 2 1/15 1.0 200 2.5 15 1/15 1.2 120 1.4 15 1890 8.2 10.3 15 5.3 6.7 15 312VE-* 3 1/15 1.5 300 3.6 15 1/15 1.8 180 2.0 15 2730 11.9 14.8 15 7.7 10 15 315VE-* 3 1/15 1.5 300 3.6 15 1/15 1.8 180 2.0 15 2730 11.9 14.8 15 7.7 10 15 416VE-* 4 1/15 2.0 400 4.7 15 1/15 2.4 240 2.6 15 3560 15.5 19.3 20 10 12 15 419VE-* 4 1/15 2.0 400 4.7 15 1/15 2.4 240 2.6 15 3560 15.5 19.3 20 10 12 15 523VE-* 5 1/15 2.5 500 5.8 15 1/15 3.0 300 3.2 15 4400 19.1 23.9 25 12 15.1 20 627VE-* 6 1/15 3.0 600 6.9 15 1/15 3.6 360 3.8 15 5230 22.7 28.4 30 15 18 20

* = S2 or T3. Refer to Nomenclature for details

FPI

QTY.

1 1/15 0.5 100 1.4 15 1/15 0.6 60 0.8 15 1060 4.6 5.8 15 3.0 3.8 15

1 1/15 0.5 100 1.4 15 1/15 0.6 60 0.75 15 1060 4.6 5.8 15 3.0 3.8 15

PSC MOTORS EC MOTORS

FLA

TOTAL

WATTS

MCA

(A)

MAX. FUSE

(AMPS)

FLA

TOTAL

WATTS

MCA

(A)

MAX.

FUSE

(AMPS)

TOTAL WATTS

208-230/1/60 208-230/3/60

MCA

(A)

MAX.

TOTAL

FUSE

(AMPS)

AMPS

15 7.7 10 15

TOTAL

AMPS

MCA

(A)

MAX.

FUSE

(AMPS)

Page 8

ELECTRICAL DATA - 460/1/60

27/04/16

T30-TLP-PDI-17

- 8 -

TLP

MODEL

TLP

209ME-S4 211ME-S4 2 1/15 0.8 200 0.9 15 1890 4.1 5.1 15 214ME-S4 2 1/15 0.8 200 0.9 15 1890 4.1 5.1 15 317ME-S4 3 1/15 1.2 300 1.3 15 2730 5.9 7.4 15 320ME-S4 3 1/15 1.2 300 1.3 15 2730 5.9 7.4 15 423ME-S4 4 1/15 1.6 400 1.7 15 3560 7.7 9.7 15 426ME-S4 4 1/15 1.6 400 1.7 15 3560 7.7 9.7 15 532ME-S4 5 1/15 2.0 500 2.1 15 4400 9.6 12.0 15 639ME-S4 6 1/15 2.4 600 2.5 15 5230 11.4 14.2 15

207LE-S4 209LE-S4 2 1/15 0.8 200 0.9 15 1890 4.1 5.1 15 211LE-S4 2 1/15 0.8 200 0.9 15 1890 4.1 5.1 15 314LE-S4 3 1/15 1.2 300 1.3 15 2730 5.9 7.4 15 317LE-S4 3 1/15 1.2 300 1.3 15 2730 5.9 7.4 15 419LE-S4 4 1/15 1.6 400 1.7 15 3560 7.7 9.7 15 422LE-S4 4 1/15 1.6 400 1.7 15 3560 7.7 9.7 15 527LE-S4 5 1/15 2.0 500 2.1 15 4400 9.6 12.0 15 631LE-S4 6 1/15 2.4 600 2.5 15 5230 11.4 14.2 15

206VE-S4 208VE-S4 2 1/15 0.8 200 0.9 15 1890 4.1 5.1 15 209VE-S4 2 1/15 0.8 200 0.9 15 1890 4.1 5.1 15 312VE-S4 3 1/15 1.2 300 1.3 15 2730 5.9 7.4 15 315VE-S4 3 1/15 1.2 300 1.3 15 2730 5.9 7.4 15 416VE-S4 4 1/15 1.6 400 1.7 15 3560 7.7 9.7 15 419VE-S4 4 1/15 1.6 400 1.7 15 3560 7.7 9.7 15 523VE-S4 5 1/15 2.0 500 2.1 15 4400 9.6 12.0 15 627VE-S4 6 1/15 2.4 600 2.5 15 5230 11.4 14.2 15

FPI

QTY.

2 1/15 0.8 200 0.9 15 1890 4.1 5.1 15

ELECTRIC DEFROST MODELS

FAN MOTORS DEFROST HEATERS

FLA

TOTAL

PSC MOTORS

WATTS

MCA

(A)

MAX. FUSE

(AMPS)

TOTAL

WATTS

TOTAL

AMPS

60Hz

MCA

(A)

MAX. FUSE

(AMPS)

Page 9

ELECTRICAL DATA - 115/1/60

27/04/16

T30-TLP-PDI-17

- 9 -

TLP

HOT GAS DEFROST

60Hz

WITH DRAIN PAN HEATER MODELS

FAN MOTORS DRAIN PAN HEATERS

MODEL

TLP

209M#-S1 211M#-S1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 410 3.6 4.5 15 214M#-S1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 410 3.6 4.5 15 317M#-S1 3 1/15 3.0 300 3.3 15 1/15 3.0 180 3.3 15 560 4.9 6.1 15 320M#-S1 3 1/15 3.0 300 3.3 15 1/15 3.0 180 3.3 15 560 4.9 6.1 15 423M#-S1 4 1/15 4.0 400 4.3 15 1/15 4.0 240 4.3 15 720 6.3 7.8 15 426M#-S1 4 1/15 4.0 400 4.3 15 1/15 4.0 240 4.3 15 720 6.3 7.8 15 532M#-S1 5 1/15 5.0 500 5.3 15 1/15 5.0 300 5.3 15 880 7.7 9.6 15 639M#-S1 6 1/15 6.0 600 6.3 15 1/15 6.0 360 6.3 15 1030 9.0 11.2 15 207L#-S1 209L#-S1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 410 3.6 4.5 15

211L#-S1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 410 3.6 4.5 15 314L#-S1 3 1/15 3.0 300 3.3 15 1/15 3.0 180 3.3 15 560 4.9 6.1 15 317L#-S1 3 1/15 3.0 300 3.3 15 1/15 3.0 180 3.3 15 560 4.9 6.1 15 419L#-S1 4 1/15 4.0 400 4.3 15 1/15 4.0 240 4.3 15 720 6.3 7.8 15 422L#-S1 4 1/15 4.0 400 4.3 15 1/15 4.0 240 4.3 15 720 6.3 7.8 15 527L#-S1 5 1/15 5.0 500 5.3 15 1/15 5.0 300 5.3 15 880 7.7 9.6 15 631L#-S1 6 1/15 6.0 600 6.3 15 1/15 6.0 360 6.3 15 1030 9.0 11.2 15 206V#-S1 208V#-S1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 410 3.6 4.5 15 209V#-S1 2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 410 3.6 4.5 15 312V#-S1 3 1/15 3.0 300 3.3 15 1/15 3.0 180 3.3 15 560 4.9 6.1 15 315V#-S1 3 1/15 3.0 300 3.3 15 1/15 3.0 180 3.3 15 560 4.9 6.1 15 416V#-S1 4 1/15 4.0 400 4.3 15 1/15 4.0 240 4.3 15 720 6.3 7.8 15 419V#-S1 4 1/15 4.0 400 4.3 15 1/15 4.0 240 4.3 15 720 6.3 7.8 15 523V#-S1 5 1/15 5.0 500 5.3 15 1/15 5.0 300 5.3 15 880 7.7 9.6 15 627V#-S1 6 1/15 6.0 600 6.3 15 1/15 6.0 360 6.3 15 1030 9.0 11.2 15

# = T or G. Refer to Nomenclature for details

FPI

QTY.

2 1/15 2.0 200 2.3 15 1/15 2.0 120 2.3 15 410 3.6 4.5 15

PSC MOTORS EC MOTORS

FLA

TOTAL

WATTS

MCA

(A)

MAX.

FUSE

(AMPS)

FLA

TOTAL

WATTS

MCA

(A)

MAX.

FUSE

(AMPS)

TOTAL

WATTS

TOTAL

AMPS

MCA

(A)

MAX. FUSE

(AMPS)

Page 10

ELECTRICAL DATA - 208-230/1/60

27/04/16

T30-TLP-PDI-17

- 10 -

TLP

HOT GAS DEFROST

60Hz

WITH DRAIN PAN HEATER MODELS

FAN MOTORS DRAIN PAN HEATERS

MODEL

TLP

209M^-S2 211M^-S2 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 410 1.8 2.2 15 214M^-S2 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 410 1.8 2.2 15 317M^-S2 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 560 2.4 3.0 15 320M^-S2 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 560 2.4 3.0 15 423M^-S2 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 720 3.1 3.9 15 426M^-S2 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 720 3.1 3.9 15 532M^-S2 5 1/15 2.5 500 2.6 15 1/15 3.0 300 3.2 15 880 3.8 4.8 15 639M^-S2 6 1/15 3.0 600 3.1 15 1/15 3.6 360 3.8 15 1030 4.0 5.0 15

207L^-S2 209L^-S2 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 410 1.8 2.2 15 211L^-S2 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 410 1.8 2.2 15 314L^-S2 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 560 2.4 3.0 15 317L^-S2 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 560 2.4 3.0 15 419L^-S2 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 720 3.1 3.9 15 422L^-S2 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 720 3.1 3.9 15 527L^-S2 5 1/15 2.5 500 2.6 15 1/15 3.0 300 3.2 15 880 3.8 4.8 15 631L^-S2 6 1/15 3.0 600 3.1 15 1/15 3.6 360 3.8 15 1030 4.0 5.0 15 206V^-S2 208V^-S2 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 410 1.8 2.2 15 209V^-S2 2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 410 1.8 2.2 15 312V^-S2 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 560 2.4 3.0 15 315V^-S2 3 1/15 1.5 300 1.6 15 1/15 1.8 180 2.0 15 560 2.4 3.0 15 416V^-S2 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 720 3.1 3.9 15 419V^-S2 4 1/15 2.0 400 2.1 15 1/15 2.4 240 2.6 15 720 3.1 3.9 15 523V^-S2 5 1/15 2.5 500 2.6 15 1/15 3.0 300 3.2 15 880 3.8 4.8 15 627V^-S2 6 1/15 3.0 600 3.1 15 1/15 3.6 360 3.8 15 1030 4.0 5.0 15

^ = T or G. Refer to Nomenclature for details

FPI

QTY.

2 1/15 1.0 200 1.1 15 1/15 1.2 120 1.4 15 410 1.8 2.2 15

PSC MOTORS EC MOTORS

FLA

TOTAL

WATTS

MCA

(A)

MAX. FUSE

(AMPS)

FLA

TOTAL

WATTS

MCA

(A)

MAX.

FUSE

(AMPS)

TOTAL

WATTS

TOTAL

AMPS

MCA

(A)

MAX.

FUSE

(AMPS)

Page 11

ELECTRICAL DATA - 460/1/60

27/04/16

T30-TLP-PDI-17

- 11 -

TLP

HOT GAS DEFROST

60Hz

WITH DRAIN PAN HEATER MODELS

FAN MOTORS DRAIN PAN HEATERS

FLA

PSC MOTORS

WATTS

MCA

(A)

MAX. FUSE

(AMPS)

TOTAL

WATTS

TOTAL

AMPS

MCA

(A)

TLP

MODEL

209M^-S4 211M^-S4 2 1/15 0.8 200 0.9 15 410 0.9 1.1 15 214M^-S4 2 1/15 0.8 200 0.9 15 410 0.9 1.1 15 317M^-S4 3 1/15 1.2 300 1.3 15 560 1.2 1.5 15 320M^-S4 3 1/15 1.2 300 1.3 15 560 1.2 1.5 15 423M^-S4 4 1/15 1.6 400 1.7 15 720 1.6 2.0 15 426M^-S4 4 1/15 1.6 400 1.7 15 720 1.6 2.0 15 532M^-S4 5 1/15 2.0 500 2.1 15 880 1.9 2.4 15 639M^-S4 6 1/15 2.4 600 2.5 15 1030 2.2 2.8 15 207L^-S4 209L^-S4 2 1/15 0.8 200 0.9 15 410 0.9 1.1 15

211L^-S4 2 1/15 0.8 200 0.9 15 410 0.9 1.1 15 314L^-S4 3 1/15 1.2 300 1.3 15 560 1.2 1.5 15 317L^-S4 3 1/15 1.2 300 1.3 15 560 1.2 1.5 15 419L^-S4 4 1/15 1.6 400 1.7 15 720 1.6 2.0 15 422L^-S4 4 1/15 1.6 400 1.7 15 720 1.6 2.0 15 527L^-S4 5 1/15 2.0 500 2.1 15 880 1.9 2.4 15 631L^-S4 6 1/15 2.4 600 2.5 15 1030 2.2 2.8 15 206V^-S4 208V^-S4 2 1/15 0.8 200 0.9 15 410 0.9 1.1 15 209V^-S4 2 1/15 0.8 200 0.9 15 410 0.9 1.1 15 312V^-S4 3 1/15 1.2 300 1.3 15 560 1.2 1.5 15 315V^-S4 3 1/15 1.2 300 1.3 15 560 1.2 1.5 15 416V^-S4 4 1/15 1.6 400 1.7 15 720 1.6 2.0 15 419V^-S4 4 1/15 1.6 400 1.7 15 720 1.6 2.0 15 523V^-S4 5 1/15 2.0 500 2.1 15 880 1.9 2.4 15 627V^-S4 6 1/15 2.4 600 2.5 15 1030 2.2 2.8 15

^ = T or G. Refer to Nomenclature for details

FPI

QTY.

2 1/15 0.8 200 0.9 15 410 0.9 1.1 15

TOTAL

MAX. FUSE

(AMPS)

Page 12

CONDUCTORS/WIRING

AND NATIONAL CODES.

-TERMINAL BLOCK TERMINAL

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL

-COMPONENT TERMINAL

4). MAY BE FACTORY INSTALLED-MOUNTED AND

3). OVERCURRENT PROTECTION FOR

1). USE COPPER CONDUCTORS ONLY

VALUE SHOWN ON EVAPORATOR NAMEPLATE.

HEATERS MUST NOT EXCEED MAXIMUM

EVAPORATOR FAN MOTORS AND DEFROST

2). USE 75°C WIRE (OR HIGHER)

WIRED ON EVAPORATOR .

NOTES

TERMINALS

OPTIONAL FACTORY OR

1-LP AIR 09/06

BY OTHERS

WIRING BY OTHERS

FACTORY WIRING

WITHOUT DEFROST TIME CLOCK

REQUIREMENTS

REFER TO EVAPORATOR

NAMEPLATE FOR ELECTRICAL

PARAGON # 8145

DEFROST CLOCK

OR EQUIVALENT

THERMOSTAT

CIRCUIT

FUSE OR

NOTE #3

BREAKER

SWITCH

PUMP DOWN

(IF USED)

NOTE #4

SPACE

LIQUID LINE

SOLENOID VALVE

NOTE #4

N.C.

WITH DEFROST TIME CLOCK

GND

SOLENOID VALVE

THERMOSTAT

BREAKER NOTE #3

FUSE OR CIRCUIT

SPACE

NOTE #4

IF(N)

2ND FUSE

OMIT

LIQUID LINE

NOTE #4

N.C.

L2(N)

REFER TO EVAPORATOR DATA PLATE FOR MOTOR QUANTITY

GND.

FAN MTR

FAN

MTR

FAN MTR

EVAPORATOR

TERMINAL BOARD

FAN MOTOR POWER PLUGS

FAN MTR

GND.

TERMINAL BOARD

REFER TO EVAPORATOR DATA PLATE FOR MOTOR QUANTITY

FAN MOTOR POWER PLUGS

EVAPORATOR

IF(N)

OMIT 2ND

L2(N)

TO MULTIPLE EVAPS

(IF APPLIC)

EVAPORATORS (IF APPLIC)

TO MULTIPLE

FUSE

GND

REQUIREMENTS

REFER TO EVAPORATOR

NAMEPLATE FOR ELECTRICAL

TLP

27/04/16

T30-TLP-PDI-17

- 12 -

WIRING DIAGRAM - 115/1/60, 208-230/1/60

STANDARD PSC MOTORS

AIR DEFROST MODELS

PSC

60Hz

Page 13

CONDUCTORS/WIRING

AND NATIONAL CODES.

-TERMINAL BLOCK TERMINAL

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL

-COMPONENT TERMINAL

4). MAY BE FACTORY INSTALLED-MOUNTED AND

3). OVERCURRENT PROTECTION FOR

1). USE COPPER CONDUCTORS ONLY

VALUE SHOWN ON EVAPORATOR NAMEPLATE.

HEATERS MUST NOT EXCEED MAXIMUM

EVAPORATOR FAN MOTORS AND DEFROST

2). USE 75°C WIRE (OR HIGHER)

WIRED ON EVAPORATOR .

NOTES

TERMINALS

OPTIONAL FACTORY OR

6-LP 460 AIR 09/06

BY OTHERS

WIRING BY OTHERS

FACTORY WIRING

WITHOUT DEFROST TIME CLOCK

PARAGON # 8145

DEFROST CLOCK OR EQUIVALENT

THERMOSTAT

CIRCUIT

FUSE OR

NOTE #3

BREAKER

SWITCH

PUMP DOWN

(IF USED)

NOTE #4

SPACE

LIQUID LINE

SOLENOID VALVE

NOTE #4

N.C.

WITH DEFROST TIME CLOCK

380/400-1-50Hz

CONTROL VOLTAGE

GND

IF(N)

2ND FUSE

OMIT

REFER TO EVAPORATOR DATA PLATE FOR MOTOR QUANTITY

GND.

FAN MTR

EVAPORATOR

FAN MOTOR POWER PLUGS

FAN MTR

GND.

TERMINAL BOARD

REFER TO EVAPORATOR DATA PLATE FOR MOTOR QUANTITY

FAN MOTOR POWER PLUGS

EVAPORATOR

IF(N)

OMIT 2ND

TO MULTIPLE

EVAPORATORS (IF APPLIC)

TO MULTIPLE

FUSE

GND

L2(N)

460-1-60 Hz

TERMINAL BOARD

THERMOSTAT

NOTE #4

N.C.

SOLENOID VALVE

SPACE

LIQUID LINE

NOTE #4

GND

L2(N)

460-1-60 Hz

380/400-1-50Hz

CONTROL VOLTAGE

NOTE #3

CIRCUIT BREAKER

FUSE OR

TLP

27/04/16

T30-TLP-PDI-17

- 13 -

WIRING DIAGRAM - 460/1/60

STANDARD PSC MOTORS

AIR DEFROST MODELS

PSC

60Hz

Page 14

WARNING

EVAP FIELD MODIFICATION

MUST BE MADE

REFER TO EVAPORATOR

COMPR INTERLOCK

FOR ALL MODELS WITHOUT DEFROST HEATER CONTACTOR

THERMOSTAT

NOTE #4

EVAPORATOR FAN MOTORS AND DEFROST HEATERS MUST NOT EXCEED

1). USE COPPER CONDUCTORS ONLY

3). OVERCURRENT PROTECTION FOR

MAXIMUM VALUE SHOWN ON EVAPORATOR NAMEPLATE.

NOTES

2). USE 75°C WIRE (OR HIGHER)

FAN MTR

DEFROST TERMINATION

CONTROL

(10.0A MAX.)

& FAN DELAY

FD-FAN DELAY

DT-DEFROST TERM

GND.

(IF USED)

SWITCH

OR EQUIVALENT

PUMP DOWN

SPACE

(IF USED)

DEFROST CLOCK PARAGON # 8145

EVAPORATOR

OPTIONAL FACTORY

FACTORY WIRING

WIRING BY OTHERS

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL AND NATIONAL CODES.

2-LP ED 12/07

-TERMINAL BLOCK TERMINAL

-COMPONENT TERMINAL

CONDUCTORS/WIRING

TERMINALS

DATA PLATE FOR MOTOR QUANTITY

EVAPORATOR

REFER TO

POWER PLUGS

FAN MOTOR

NOTE #4

SOL VALVE

L2L1

N.C.

LIQUID LINE

GND

NAMEPLATE FOR ELECTRICAL

REQUIREMENTS

OR BY OTHERS

AND WIRED ON EVAPORATOR

4.) MAY BE FACTORY INSTALLED-MOUNTED

DEFROST HEATERS

CIRCUIT BREAKER

FUSE OR

USING MAXIMUM 15A HEATER OVERCURRENT PROTECTION

15A

FAN MTR

ORANGE JUMPER

SWITCH

LIMIT

HEATER

(10.0A MAX.)

FROM H2 TO N

INSTALL ORANGE JUMPER (SUPPLIED LOOSE)

N TO H1 AS SHOWN

RELOCATE WHITE WIRE FROM

SEE NOTE:

TLP

27/04/16

T30-TLP-PDI-17

- 14 -

WIRING DIAGRAM - 208-230/1/60

STANDARD PSC MOTORS

PSC

60Hz

ELECTRIC DEFROST MODELS - SINGLE EVAPORATOR 10A MAX.

Page 15

COMPR INTERLOCK

FOR ALL MODELS USING DEFROST HEATER CONTACTOR

THERMOSTAT

NOTE #4

EVAPORATOR FAN MOTORS AND DEFROST HEATERS MUST NOT EXCEED

1). USE COPPER CONDUCTORS ONLY

3). OVERCURRENT PROTECTION FOR

MAXIMUM VALUE SHOWN ON EVAPORATOR NAMEPLATE.

NOTES

2). USE 75°C WIRE (OR HIGHER)

(IF USED)

SWITCH

OR EQUIVALENT

PUMP DOWN

SPACE

(IF USED)

DEFROST CLOCK

PARAGON # 8145

OPTIONAL FACTORY

FACTORY WIRING

WIRING BY OTHERS

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL AND NATIONAL CODES.

3-LP ED CONTACTOR SINGLE 12/07

-TERMINAL BLOCK TERMINAL

-COMPONENT TERMINAL

CONDUCTORS/WIRING

TERMINALS

NOTE #4

SOL VALVE

N.C.

LIQUID LINE

OR BY OTHERS

AND WIRED ON EVAPORATOR

4.) MAY BE FACTORY INSTALLED-MOUNTED

CIRCUIT BREAKER NOTE #3

FUSE OR

CONTACTOR

DEFROST HEATER

NOTE #3

BREAKER

FUSE OR CIRCUIT

GND

L2L1

(10.0A MAX.)

REFER TO

POWER PLUGS

MOTOR QUANTITY

DATA PLATE FOR

EVAPORATOR

FAN MOTOR

621

DEFROST TERMINATION

FD-FAN DELAY

DT-DEFROST TERM

FAN MTR

GND.

FAN MTRMTR

FAN

(10.0A MAX.)

CONTROL

& FAN DELAY

LIMIT

SWITCH

HEATER

EVAPORATOR

DEFROST HEATERS

REFER TO EVAPORATOR NAMEPLATE

FOR ELECTRICAL REQUIREMENTS

TLP

27/04/16

T30-TLP-PDI-17

- 15 -

WIRING DIAGRAM - 208-230/1/60

STANDARD PSC MOTORS

ELECTRIC DEFROST MODELS - SINGLE EVAPORATOR

PSC

60Hz

Page 16

COMPR INTERLOCK

FOR ALL MODELS USING 3 PHASE DEFROST HEATER CONTACTOR

THERMOSTAT

NOTE #4

EVAPORATOR FAN MOTORS AND DEFROST HEATERS MUST NOT EXCEED

1). USE COPPER CONDUCTORS ONLY

3). OVERCURRENT PROTECTION FOR

MAXIMUM VALUE SHOWN ON EVAPORATOR NAMEPLATE.

NOTES

2). USE 75°C WIRE (OR HIGHER)

(IF USED)

SWITCH

OR EQUIVALENT

PUMP DOWN

SPACE

(IF USED)

DEFROST CLOCK

PARAGON # 8145

OPTIONAL FACTORY

FACTORY WIRING

WIRING BY OTHERS

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL AND NATIONAL CODES.

3A-LP ED 3ph.CONTACTOR SINGLE 12/07

-TERMINAL BLOCK TERMINAL

-COMPONENT TERMINAL

CONDUCTORS/WIRING

TERMINALS

NOTE #4

SOL VALVE

N.C.

LIQUID LINE

OR BY OTHERS

AND WIRED ON EVAPORATOR

4.) MAY BE FACTORY INSTALLED-MOUNTED

CIRCUIT BREAKER

NOTE #3

FUSE OR

CONTACTOR

DEFROST HEATER

NOTE #3

BREAKER

FUSE OR CIRCUIT

GND

L2L1

DEFROST HEATERS

H2 H3

DATA PLATE FOR MOTOR QUANTITY

12 6

CONTROL

(10.0A MAX.)

& FAN DELAY

DT-DEFROST TERM

DEFROST TERMINATION

FD-FAN DELAY

MTR

FAN

MTR

FAN

GND.

SWITCH

(10.0A MAX.)

MTR

FAN

FAN MOTOR

REFER TO EVAPORATOR

POWER PLUGS

HEATER

LIMIT

EVAPORATOR

REFER TO EVAPORATOR NAMEPLATE

FOR ELECTRICAL REQUIREMENTS

TLP

27/04/16

T30-TLP-PDI-17

- 16 -

WIRING DIAGRAM - 208-230/3/60

STANDARD PSC MOTORS

ELECTRIC DEFROST MODELS - SINGLE EVAPORATOR

PSC

60Hz

Page 17

WIRING DIAGRAM - 460/1/60

REFER TO EVAPORATOR NAMEPLATE

FOR ELECTRICAL REQUIREMENTS

COMPR INTERLOCK

FOR ALL 460V MODELS USING DEFROST HEATER AND FAN CONTACTORS

THERMOSTAT

NOTE #4

EVAPORATOR FAN MOTORS AND DEFROST HEATERS MUST NOT EXCEED

1). USE COPPER CONDUCTORS ONLY

3). OVERCURRENT PROTECTION FOR

MAXIMUM VALUE SHOWN ON EVAPORATOR NAMEPLATE.

NOTES

2). USE 75°C WIRE (OR HIGHER)

MTR

FANFAN

MTR

FAN

MTR

GND.

(IF USED)

SWITCH

OR EQUIVALENT

PUMP DOWN

SPACE

(IF USED)

BREAKER

NOTE #3

CIRCUIT

FUSE OR

DEFROST CLOCK

PARAGON # 8145

EVAPORATOR

OPTIONAL FACTORY

FACTORY WIRING

WIRING BY OTHERS

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL AND NATIONAL CODES.

7-LP ED CONTACTOR SINGLE 12/07

-TERMINAL BLOCK TERMINAL

-COMPONENT TERMINAL

CONDUCTORS/WIRING

TERMINALS

DATA PLATE FOR MOTOR QUANTITY

EVAPORTOR

REFER TO

POWER PLUGS

FAN MOTOR

NOTE #4

SOL VALVE

L2L1

N.C.

LIQUID LINE

GND

OR BY OTHERS

AND WIRED ON EVAPORATOR

4.) MAY BE FACTORY INSTALLED-MOUNTED

CIRCUIT BREAKER NOTE #3

FUSE OR

GND

L2(N)

CONTACTOR

DEFROST HEATER

EVAP FAN

CONTACTOR

COIL DEFROST HEATERS

H1 H2

DEFROST TERMINATION

CONTROL

& FAN DELAY

(10.0A MAX.)

FD-FAN DELAY

DT-DEFROST TERM

(10.0A MAX.)

LIMIT

SWITCH

HEATER

27/04/16

T30-TLP-PDI-17

- 17 -

TLP

STANDARD PSC MOTORS

ELECTRIC DEFROST MODELS - SINGLE EVAPORATOR

PSC

60Hz

Page 18

MUST BE MADE

EVAP#2 FIELD MODIFICATION

WARNING

COMPR INTERLOCK

FOR ALL MODELS USING DEFROST HEATER CONTACTOR

THERMOSTAT

NOTE #4

EVAPORATOR FAN MOTORS AND DEFROST HEATERS MUST NOT EXCEED

1). USE COPPER CONDUCTORS ONLY

3). OVERCURRENT PROTECTION FOR

MAXIMUM VALUE SHOWN ON EVAPORATOR NAMEPLATE.

NOTES

2). USE 75°C WIRE (OR HIGHER)

MTR

FANFAN

MTR

FAN MTR

DEFROST TERMINATION

CONTROL

(10.0A MAX.)

& FAN DELAY

FD-FAN DELAY

DT-DEFROST TERM

GND.

(IF USED)

SWITCH

OR EQUIVALENT

PUMP DOWN

SPACE

(IF USED)

BREAKER

NOTE #3

CIRCUIT

FUSE OR

DEFROST CLOCK PARAGON # 8145

EVAPORATOR

OPTIONAL FACTORY

FACTORY WIRING

WIRING BY OTHERS

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL AND NATIONAL CODES.

4-LP ED CONTACTOR MULTI 12/07

-TERMINAL BLOCK TERMINAL

-COMPONENT TERMINAL

CONDUCTORS/WIRING

TERMINALS

DATA PLATE FOR MOTOR QUANTITY

EVAPORATOR

REFER TO

POWER PLUGS

FAN MOTOR

NOTE #4

SOL VALVE

N.C.

LIQUID LINE

GND

OR BY OTHERS

AND WIRED ON EVAPORATOR

4.) MAY BE FACTORY INSTALLED-MOUNTED

DEFROST HEATERS

CIRCUIT BREAKER NOTE #3

FUSE OR

DEFROST HEATER

CONTACTOR

EVAPORATOR

MTR

FAN

MTR

FANFAN

MTR

FAN MOTOR POWER PLUGS

EVAPORATOR

MOTOR QUANTITY

DATA PLATE FOR

REFER TO

GND.

DEFROST TERMINATION

DT-DEFROST TERM FD-FAN DELAY

(10.0A MAX.)

CONTROL

& FAN DELAY

DEFROST HEATERS

* Remove & Insulate

* Fan delay not used on second evap / use fan contactor if total fan amps exceeds 10A

PRIMARY

SECONDARY

FUSE OR

BREAKER NOTE #3

CIRCUIT

H1NH2

H1N

LIMIT

(10.0A MAX.)

SWITCH

HEATER

LIMIT

(10.0A MAX.)

SWITCH

HEATER

REFER TO EVAPORATOR NAMEPLATE

FOR ELECTRICAL REQUIREMENTS

RELOCATE WHITE WIRE FROM

N AS SHOWN

SEE NOTE:

REMOVE AND INSULATE

AS SHOWN

TLP

27/04/16

T30-TLP-PDI-17

- 18 -

ELECTRIC DEFROST MODELS - MULTIPLE EVAPORATORS

WIRING DIAGRAM - 208-230/1/60

STANDARD PSC MOTORS

PSC

60Hz

Page 19

WARNING

EVAP#2 FIELD MODIFI-

CATION MUST BE MADE

COMPR INTERLOCK

FOR ALL 460V MODELS USING DEFROST HEATER AND FAN CONTACTORS

THERMOSTAT

NOTE #4

EVAPORATOR FAN MOTORS AND DEFROST HEATERS MUST NOT EXCEED

1). USE COPPER CONDUCTORS ONLY

3). OVERCURRENT PROTECTION FOR

MAXIMUM VALUE SHOWN ON EVAPORATOR NAMEPLATE.

NOTES

2). USE 75°C WIRE (OR HIGHER)

MTR

FANFAN

MTR

FAN MTR

GND.

(IF USED)

SWITCH

OR EQUIVALENT

PUMP DOWN

SPACE

(IF USED)

BREAKER

NOTE #3

CIRCUIT

FUSE OR

DEFROST CLOCK

PARAGON # 8145

EVAPORATOR

OPTIONAL FACTORY

FACTORY WIRING

WIRING BY OTHERS

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL AND NATIONAL CODES.

8-LP 460v ED CONTACTOR MULTI 09/06

-TERMINAL BLOCK TERMINAL

-COMPONENT TERMINAL

CONDUCTORS/WIRING

TERMINALS

DATA PLATE FOR MOTOR QUANTITY

EVAPORATOR

REFER TO

POWER PLUGS

FAN MOTOR

NOTE #4

SOL VALVE

N.C.

LIQUID LINE

GND

OR BY OTHERS

AND WIRED ON EVAPORATOR

4.) MAY BE FACTORY INSTALLED-MOUNTED

CIRCUIT BREAKER NOTE #3

FUSE OR

GND

L2(N)

CONTACTOR

DEFROST HEATER

EVAP FAN

CONTACTOR

MTR

FAN

MTR

FAN

GND.

EVAPORATOR

REFER TO EVAPORATOR

MOTOR QUANTITY

DATA PLATE FOR

MTR

FAN

POWER PLUGS

FAN MOTOR

NOTE #3

FUSE OR CIRCUIT

BREAKER

PRIMARY

SECONDARY

* Note: Fan Delay not used on second evap

DEFROST HEATERS

H1 H2

DEFROST TERMINATION

DT-DEFROST TERM FD-FAN DELAY

CONTROL

(10.0A MAX.)

& FAN DELAY

DEFROST TERMINATION

DT-DEFROST TERM FD-FAN DELAY

CONTROL

(10.0A MAX.)

& FAN DELAY

DEFROST HEATERS

H1 H2

HEATER SWITCH

LIMIT

(10.0A MAX.)

LIMIT

SWITCH

HEATER

N AS SHOWN

RELOCATE WHITE WIRE FROM

REFER TO EVAPORATOR NAMEPLATE

FOR ELECTRICAL REQUIREMENTS

TLP

27/04/16

T30-TLP-PDI-17

- 19 -

ELECTRIC DEFROST MODELS - MULTIPLE EVAPORATORS

WIRING DIAGRAM - 460/1/60

STANDARD PSC MOTORS

PSC

60Hz

Page 20

REFER TO EVAPORATOR

NAMEPLATE FOR ELECTRICAL

REQUIREMENTS

EVAPORATOR FAN MOTORS AND DEFROST HEATERS MUST NOT EXCEED

1). USE COPPER CONDUCTORS ONLY

3). OVERCURRENT PROTECTION FOR

MAXIMUM VALUE SHOWN ON EVAPORATOR NAMEPLATE.

NOTES

2). USE 75°C WIRE (OR HIGHER)

MTR

FANFAN

MTR

FAN

MTR

*FAN HEATER

CONTROL

GND.

EVAPORATOR

OPTIONAL FACTORY

FACTORY WIRING

WIRING BY OTHERS

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL AND NATIONAL CODES.

5-LP HG 08/06

-TERMINAL BLOCK TERMINAL

-COMPONENT TERMINAL

CONDUCTORS/WIRING

TERMINALS

DATA PLATE FOR MOTOR QUANTITY

EVAPORATOR

REFER TO

POWER PLUGS

FAN MOTOR

L2(N)

GND

OR BY OTHERS

AND WIRED ON EVAPORATOR

4.) MAY BE FACTORY INSTALLED-MOUNTED

DRAIN PAN HEATER

CIRCUIT

BREAKER

FUSE OR

USING MAXIMUM 15A HEATER OVERCURRENT PROTECTION

15A

**DEFROST TERMINATION

CONTROL

FAN MOTOR / HEATER WIRING

NOTE: DURING THE HOT GAS DEFROST CYCLE

THE FAN/HEATER CONTROL DE-ENERGIZES THE

EVAPORATOR FANS AND ENERGIZES THE

DRAIN PAN HEAT ER.

(ANYTIME THE TEMPERATURE OF THE INCOMING

REFRIGERANT GAS IS ABOVE 50° F).

*FAN HEATER

CONTROL

ON REVERSE CYCLE LOCATED AT SUCTION LINE.

ON THREE-PIPE LOCATED AT DISTRIBUTOR SIDE PORT.

CONTROL

**DEFROST TERMINATION

OPTIONAL FACTORY WIRED OR BY OTHERS

LOCATED ON TUBE END SHEET

THE CONTROL CLOSES WHEN REACHES 55` F (20 F DIFF)

(IF APPLICABLE)

REFER TO SPECIFIC SYSTEM WIRING DIAGRAM (BY OTHERS) FOR FIELD CONTROL WIRING

TLP

27/04/16

T30-TLP-PDI-17

- 20 -

WIRING DIAGRAM - 115/1/60, 208-230/1/60

STANDARD PSC MOTORS

HOT GAS DEFROST MODELS

PSC

60Hz

Page 21

REFER TO EVAPORATOR

EVAPORATOR FAN MOTORS AND DEFROST HEATERS MUST NOT EXCEED

1). USE COPPER CONDUCTORS ONLY

3). OVERCURRENT PROTECTION FOR

MAXIMUM VALUE SHOWN ON EVAPORATOR NAMEPLATE.

NOTES

2). USE 90°C WIRE (OR HIGHER)

MTR

FANFAN

MTR

FAN MTR

*FAN HEATER

CONTROL

GND.

EVAPORATOR

OPTIONAL FACTORY

FACTORY WIRING

WIRING BY OTHERS

ALL FIELD WIRING MUST BE DONE IN COMPLIANCE WITH ALL APPLICABLE LOCAL AND NATIONAL CODES.

9-LP 460 HG 05/06

-TERMINAL BLOCK TERMINAL

-COMPONENT TERMINAL

CONDUCTORS/WIRING

TERMINALS

DATA PLATE FOR MOTOR QUANTITY

EVAPORATOR

REFER TO

POWER PLUGS

FAN MOTOR

GND

NAMEPLATE FOR ELECTRICAL

REQUIREMENTS

OR BY OTHERS

AND WIRED ON EVAPORATOR

4.) MAY BE FACTORY INSTALLED-MOUNTED

DRAIN PAN HEATER

CIRCUIT

BREAKER

FUSE OR

USING MAXIMUM 15A HEATER OVERCURRENT PROTECTION

15A

**DEFROST TERMINATION

CONTROL

REFER TO SPECIFIC SYSTEM WIRING DIAGRAM

(BY OTHERS) FOR FIELD CONTROL WIRING

FAN MOTOR / HEATER WIRING

NOTE: DURING THE HOT GAS DEFROST CYCLE THE FAN/HEATER CONTROL DE-ENERGIZES THE EVAPORATOR FANS AND ENERGIZES THE DRAIN PAN HEATER. (ANYTIME THE TEMPERATURE OF THE INCOMING REFRIGERANT GAS IS ABOVE 50° F).

*FAN HEATER

CONTROL

ON REVERSE CYCLE LOCATED AT SUCTION LINE. ON THREE-PIPE LOCATED AT DISTRIBUTOR SIDE PORT.

CONTROL

**DEFROST TERMINATION

OPTIONAL FACTORY WIRED OR BY OTHERS LOCATED ON TUBE END SHEET.

THE CONTROL CLOSES WHEN REACHES 55` F (20 F DIFF)

(IF APPLICABLE)

EVAP FAN CONTACTOR

CONTACTOR

DEFROST HEATER

3H1H2N

TLP

27/04/16

T30-TLP-PDI-17

- 21 -

WIRING DIAGRAM - 460/1/60

STANDARD PSC MOTORS

HOT GAS DEFROST MODELS

PSC

60Hz

Page 22

TLP

SmartSpeed

Evaporators

Energy Consumption (Watt

EVAP w/ PSC

EVAP with SmartSpeed

REFRIGERATION = FULL SPEED = 60W PER MOTOR

OFF CYCLE = LOW SPEED = 13W PER MOTOR 40 % EXTRA ENERGY SAVINGS vs. FIXED SPEED EC MOTOR ON EVAPORATOR

10 % EXTRA ENERGY SAVINGS ON COMPRESSOR WHEN USING SMARTSPEED EVAPORATOR

DESIGN HIGHLIGHTS

NO COMPLEX CONTROLS, NO COST ADDER, SIMPLE TO UNDERSTAND

PATENT

PENDING

27/04/16

T30-TLP-PDI-17

- 22 -

ECM

60Hz

DESIGN FEATURES

US Patent No.

8,635,883

• Refrigeration mode – EC motor operates at full speed.

• O󰀨 Cycle mode – EC motor operates at reduced speed.

• Standard on all EC Motors

• NO special controls required.

Consumption 60 W per motor

Consumption 13 W per motor.

• Energy saving benet on motor and compressor wattage consumption:

20000

ENERGY CONSUMPTION COMPA RISON:

-Hours)

18000

16000

14000

12000

10000

with PSC vs ECM vs SmartSpeed Evaporator Fan Motors

Compressor w/ PSC Compressor w/ ECM

Compressor w/ SmartSpeed

8000

6000

4000

2000

0 50 100 150 200 250 300 350 400 450 500

Time (minutes)

Note: Data collected on a typical freezer application with a 3HP low temp condensing unit and a 4 fan TLP evaporator

ADDITIONAL ENERGY SAVINGS WHEN USING SMARTSPEED EVAPS

EVAP w/ ECM

INSTALLATION NOTES

EC motors are factory wired for SmartSpeed operation on evaporators equipped with a factory installed thermostat.

For SmartSpeed operation on Evaporators without a factory installed thermostat,

a eld wired SPDT type thermostat is required.

Page 23

TLP

27/04/16

T30-TLP-PDI-17

- 23 -

WIRING DIAGRAM - 115/1/60, 208-230/1/60

OPTIONAL EC MOTORS with

AIR DEFROST MODELS

ECM

60Hz

Page 24

TLP

27/04/16

T30-TLP-PDI-17

- 24 -

WIRING DIAGRAM - 208-230/1/60

OPTIONAL EC MOTORS with

ELECTRIC DEFROST MODELS

ECM

60Hz

Page 25

TLP

27/04/16

T30-TLP-PDI-17

- 25 -

ELECTRIC DEFROST MODELS - MULTIPLE EVAPORATORS

WIRING DIAGRAM - 208-230/1/60

OPTIONAL EC MOTORS with

ECM

60Hz

Page 26

TLP

27/04/16

T30-TLP-PDI-17

- 26 -

WIRING DIAGRAM - 115/1/60, 208-230/1/60

OPTIONAL EC MOTORS with

HOT GAS DEFROST MODELS

ECM

60Hz

Page 27

.438 SLOTS IN MOUNTING BRACKETS

AIR THROW APPROX 35' IN OPEN SPACE

MINIMUM

11 7/83 1/8

[305][302] [79]

[76]

[403]

15 7/8

[35]

1 3/8

3/4 MPT / 3/4 FLARE DRAIN CONNECTION

4, 5 AND 6 FAN MODELS.

6 1/2

[165]

MTG SLOTS

13 7/16

[341]

(TOP VIEW)

REFRIGERATION CONNECTIONS. SUCTION & LIQUID.

ELECTRICAL CONNECTIONS.

13 7/16

MTG SLOTS

[165]

6 1/26 1/2

TYP

[102]

[341]

1, 2 AND 3 FAN MODELS.

(TOP VIEW)

TLP

27/04/16

T30-TLP-PDI-17

- 27 -

DIMENSIONAL DATA

MODEL

NO. OF

FANS

A B C

IN (mm) IN (mm) IN (mm)

SUCTION

CONNECTION

(ID) SWEAT

DISTRIBUTOR

INLET

SIZE

HOT GAS

DISTRIBUTOR

SIDE PORT

DRAIN PAN

LOOP

104M^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 1/2 1/2 N/A 106M^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 1/2 1/2 N/A 107M^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 1/2 1/2 N/A 209M# 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 1/2 1/2 5/8 211M# 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 1/2 1/2 5/8 214M# 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 1/2 1/2 5/8 317M# 3 62 1/4 (1581) 49 1/4 (1251) N/A N/A 7/8 1/2 1/2 7/8 320M# 3 62 1/4 (1581) 49 1/4 (1251) N/A N/A 7/8 1/2 1/2 7/8 423M# 4 78 1/4 (1988) 32 5/8 (829) 32 5/8 (829) 1 1/8 1/2 1/2 7/8 426M# 4 78 1/4 (1988) 32 5/8 (829) 32 5/8 (829) 1 1/8 1/2 1/2 7/8 532M# 5 94 1/4 (2394) 32 5/8 (829) 48 5/8 (1235) 1 3/8 1/2 1/2 1 1/8 639M# 6 110 1/4 (2800) 48 5/8 (1235) 48 5/8 (1235) 1 3/8 7/8 5/8 1 1/8

104L^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 1/2 1/2 N/A 105L^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 1/2 1/2 N/A 106L^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 1/2 1/2 N/A 207L# 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 1/2 1/2 5/8 209L# 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 1/2 1/2 5/8 211L# 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 1/2 1/2 5/8 314L# 3 62 1/4 (1581) 49 1/4 (1251) N/A N/A 7/8 1/2 1/2 7/8 317L# 3 62 1/4 (1581) 49 1/4 (1251) N/A N/A 1 1/8 1/2 1/2 7/8 419L# 4 78 1/4 (1988) 32 5/8 (829) 32 5/8 (829) 1 1/8 1/2 1/2 7/8 422L# 4 78 1/4 (1988) 32 5/8 (829) 32 5/8 (829) 1 1/8 7/8 5/8 7/8 527L# 5 94 1/4 (2394) 32 5/8 (829) 48 5/8 (1235) 1 3/8 7/8 5/8 1 1/8 631L# 6 110 1/4 (2800) 48 5/8 (1235) 48 5/8 (1235) 1 3/8 7/8 5/8 1 1/8

103V^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 1/2 1/2 N/A 104V^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 1/2 1/2 N/A 105V^ 1 30 1/4 (768) 17 1/4 (438) N/A N/A 5/8 1/2 1/2 N/A 206V# 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 1/2 1/2 5/8 208V# 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 1/2 1/2 5/8 209V# 2 46 1/4 (1175) 33 1/4 (845) N/A N/A 7/8 1/2 1/2 5/8 312V# 3 62 1/4 (1581) 49 1/4 (1251) N/A N/A 7/8 1/2 1/2 7/8 315V# 3 62 1/4 (1581) 49 1/4 (1251) N/A N/A 1 1/8 1/2 1/2 7/8 416V# 4 78 1/4 (1988) 32 5/8 (829) 32 5/8 (829) 1 1/8 1/2 1/2 7/8 419V# 4 78 1/4 (1988) 32 5/8 (829) 32 5/8 (829) 1 1/8 7/8 5/8 7/8 523V# 5 94 1/4 (2394) 32 5/8 (829) 48 5/8 (1235) 1 3/8 7/8 5/8 1 1/8 627V# 6 110 1/4 (2800) 48 5/8 (1235) 48 5/8 (1235) 1 3/8 7/8 5/8 1 1/8

# = A, E, T, H, G, or R. ^ = A or E. T, H, G or R available in 2 to 6 fan models only Refer to Nomenclature for details

Page 28

SHIPPING WEIGHTS

27/04/16

T30-TLP-PDI-17

- 28 -

TLP

Air Defrost and Hot Gas Defrost with Drain Pan Heater Models

MODEL NUMBER

104MA N/A N/A N/A N/A N/A N/A 104WA 45 (20) 106MA N/A N/A N/A N/A N/A N/A 106WA 47 (21) 107MA N/A N/A N/A N/A N/A N/A 107WA 49 (22) 209MA 209MT 209MG 207LG 207LT 206VG 206VT 209WA 70 (32) 211MA 211MT 211MG 209LG 209LT 208VG 208VT 211WA 74 (33) 214MA 214MT 214MG 211LG 211LT 209VG 209VT 214WA 78 (35) 317MA 317MT 317MG 314LG 314LT 312VG 312VT 317WA 101 (46) 320MA 320MT 320MG 317LG 317LT 315VG 315VT 320WA 107 (48) 423MA 423MT 423MG 419LG 419LT 416VG 416VT 423WA 117 (53) 426MA 426MT 426MG 422LG 422LT 419VG 419VT 426WA 135 (61) 532MA 532MT 532MG 527LG 527LT 523VG 523VT 532WA 163 (74) 639MA 639MT 639MG 631LG 631LT 627VG 627VT 639WA 192 (87)

Electric Defrost Models

MODEL NUMBER

104ME 104LE 103VE 104WE 49 (22) 106ME 105LE 104VE 106WE 51 (23) 107ME 106LE 105VE 107WE 53 (24) 209ME 207LE 206VE 209WE 76 (34)

211ME 209LE 208VE 211WE 80 (36) 214ME 211LE 209VE 214WE 84 (38) 317ME 314LE 312VE 317WE 109 (49) 320ME 317LE 315VE 320WE 115 (52) 423ME 419LE 416VE 423WE 127 (58) 426ME 422LE 419VE 426WE 145 (66) 532ME 527LE 523VE 532WE 176 (80) 639ME 631LE 627VE 639WE 207 (94)

SHIPPING WEIGHT LB. (kg)

Hot Gas Defrost with Drain Pan Loop Models

MODEL NUMBER

209MH 209MR 207LH 207LR 206VH 206VR 87 (39)

211MH 211MR 209LH 209LR 208VH 208VR 91 (41) 214MH 214MR 211LH 211LR 209VH 209VR 95 (43) 317MH 317MR 314LH 314LR 312VH 312VR 124 (56) 320MH 320MR 317LH 317LR 315VH 315VR 130 (59) 423MH 423MR 419LH 419LR 416VH 416VR 145 (66) 426MH 426MR 422LH 422LR 419VH 419VR 163 (74) 532MH 532MR 527LH 527LR 523VH 523VR 198 (90) 639MH 639MR 631LH 631LR 627VH 627VR 233 (106)

SHIPPING WEIGHT

LB. (kg)

Page 29

RECOMMENDED EXPANSION VALVE SELECTIONS

27/04/16

T30-TLP-PDI-17

- 29 -

TLP

SPORLAN

MODEL

104M N/A EBQE-AA-*C EBQE-AAA-VC EBQE-AAA-JC 106M L-1/2 EBQE-AA-*C EBQE-AA-VC EBQE-AA-JC 107M L-1/2 EBQE-A-*C EBQE-AA-VC EBQE-AA-JC 209M L-3/4 EBQE-A-*C EBQE-AA-VC EBQE-AA-JC 211M L-1 EBQE-A-*C EBQE-A-VC EBQE-A-JC 214M L-1 EBQE-B-*C EBQE-A-VC EBQE-A-JC 317M L-1 1/2 EBQE-B-*C EBQE-A-VC EBQE-A-JC 320M L-1 1/2 EBQE-B-*C EBQE-B-VC EBQE-A-JC 423M L-2 EBQE-B-*C EBQE-B-VC EBQE-A-JC 426M L-2 EBQE-C-*C EBQE-B-VC EBQE-B-JC 532M L-2 1/2 EBQE-C-*C EBQE-B-VC EBQE-B-JC 639M G-3 EBQE-C-*C EBQE-C-VC EBQE-C-JC

* Varies with refrigerant: S = R404A, P = R507

FACTORY

INSTALLED

NOZZLE

ALCO

MODEL

104M N/A HFESC 1/4 SC HFESC 1/2 HC HFESC 1/2 MC 106M L-1/2 HFESC 1/2 SC HFESC 1/2 HC HFESC 3/4 MC 107M L-1/2 HFESC 1/2 SC HFESC 1/2 HC HFESC 3/4 MC 209M L-3/4 HFESC 1 SC HFESC 1 HC HFESC 3/4 MC 211M L-1 HFESC 1 SC HFESC 1 HC HFESC 1 MC 214M L-1 HFESC 1-1/4 SC HFESC 1-1/2 HC HFESC 1 MC 317M L-1 1/2 HFESC 1-1/2 SC HFESC 1-1/2 HC HFESC 1-1/2 MC 320M L-1 1/2 HFESC 1-1/2 SC HFESC 2 HC HFESC 1-3/4 MC 423M L-2 HFESC 2 SC HFESC 2 HC HFESC 1-3/4 MC 426M L-2 HFESC 2 SC HFESC 2-1/2 HC HFESC 2-1/2 MC 532M L-2 1/2 HFESC 3-1/2 SC HFESC 2-1/2 HC HFESC 2-1/2 MC 639M G-3 HFESC 3-1/2 SC HFESC 3 HC HFESC 4 MC

FACTORY

INSTALLED

NOZZLE

DANFOSS

MODEL

104M N/A TUAE-R404A-4-N TUAE-R22-4-N TUAE-R134a-4-N 106M L-1/2 TUAE-R404A-5-N TUAE-R22-5-N TUAE-R134a-5-N 107M L-1/2 TUAE-R404A-6-N TUAE-R22-5-N TUAE-R134a-5-N 209M L-3/4 TUAE-R404A-7-N TUAE-R22-6-N TUAE-R134a-6-N 211M L-1 TUAE-R404A-7-N TUAE-R22-6-N TUAE-R134a-6-N 214M L-1 TUAE-R404A-8-N TUAE-R22-7-N TUAE-R134a-7-N 317M L-1 1/2 TUAE-R404A-8-N TUAE-R22-8-N TUAE-R134a-8-N 320M L-1 1/2 TUAE-R404A-9-N TUAE-R22-8-N TUAE-R134a-8-N 423M L-2 TUAE-R404A-9-N TUAE-R22-8-N TUAE-R134a-9-N 426M L-2 TCAE-R404A-TC1-N TUAE-R22-9-N TUAE-R134a-9-N 532M L-2 1/2 TCAE-R404A-TC2-N TUAE-R22-9-N TCAE-R134a-TC1-N 639M G-3 TCAE-R404A-TC3-N TCAE-R22-TC1-N TCAE-R134a-TC2-N

† If using 407C, superheat setting must be adjusted by turning 1 - 1.5 turns clockwise.

FACTORY

INSTALLED

NOZZLE

R404A

R507

MEDIUM TEMPERATURE MODELS

R407A

R404A

R507

R404A

R507

R407C

R22

R407A

R407C

R22

R407A

R407C

R22

R134a

†

R134a

If correct nozzle is not

available, the proper

orice size can be

drilled in the eld using

the following chart

NOZZLE ORIFICE

No.

1/2 .070 3/4 .086

1 .0995

1-1/2 .120

2 .1406

2-1/2 .157

3 .172 4 .199 5 .211 6 .242 8 .266

10 .281

DRILL

SIZE

IN.

Above selections based on:

1) 100°F (38°C) vapor free liquid entering expansion valve

2) 110°F (43°C) Condensing temperature

3) 8 -12°F (4.4 -6.7°C) evaporator TD

Page 30

TLP

27/04/16

T30-TLP-PDI-17

- 30 -

RECOMMENDED EXPANSION VALVE SELECTIONS

LOW TEMPERATURE MODELS

SPORLAN -

MODEL

104L L-1/2 EBQE-AAA-VC EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 105L L-3/4 EBQE-AA-VC EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 106L L-1 EBQE-AA-VC EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 207L L-1 EBQE-AA-VC EBQE-AA-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 209L L-1-1/2 EBQE-AA-VC EBQE-A-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 EBQE-A-VZP40

211L L-2 EBQE-A-VC EBQE-A-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 EBQE-B-VZP40 314L L-2 EBQE-A-VC EBQE-A-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 317L L-3 EBQE-A-VC EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 419L L-3 EBQE-A-VC EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 422L G-4 EBQE-B-VC EBQE-B-VZP40 EBQE-B-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 527L G-4 EBQE-B-VC EBQE-C-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 631L G-5 EBQE-C-VC EBQE-C-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 103V L-1/2 EBQE-AAA-VC EBQE-AAA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 104V L-3/4 EBQE-AAA-VC EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 105V L-1 EBQE-AA-VC EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 206V L-1 EBQE-AA-VC EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-AA-VZP40 EBQE-A-VZP40 208V L-1 1/2 EBQE-AA-VC EBQE-AA-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 209V L-2 EBQE-A-VC EBQE-A-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 EBQE-A-VZP40 312V L-2 EBQE-A-VC EBQE-A-VZP40 EBQE-A-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 315V L-2 1/2 EBQE-A-VC EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 416V L-2 1/2 EBQE-A-VC EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 419V G-3 EBQE-A-VC EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 EBQE-B-VZP40 523V G-4 EBQE-B-VC EBQE-B-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 627V G-5 EBQE-B-VC EBQE-C-VZP40 EBQE-C-VZP40 EBQE-C-VZP40 EBQE-C-VZP40

FACTOR Y INSTALLED

R407A

NOZZLE

0° F (-18° C) EVAP. -10° F (-23° C) EVAP. -20° F (-29° C) EVAP. -30° F (-34° C) EVAP. -40° F (-40° C) EVAP.

SPORLAN -

MODEL

104L L-1/2 EBQE-AA-SC EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP 105L L-3/4 EBQE-AA-SC EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP 106L L-1 EBQE-AA-SC EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP 207L L-1 EBQE-A-SC EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP 209L 1-1/2 EBQE-A-SC EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP 211L L-2 EBQE-A-SC EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP 314L L-2 EBQE-B-SC EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP 317L L-3 EBQE-B-SC EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP 419L L-3 EBQE-B-SC EBQE-B-SZP EBQE-C-SZP EBQE-C-SZP EBQE-C-SZP 422L G-4 EBQE-C-SC EBQE-C-SZP EBQE-C-SZP EBQE-C-SZP EBQE-C-SZP 527L G-4 EBQE-C-SC EBQE-C-SZP EBQE-C-SZP EBSE-6-SZP EBSE-6-SZP 631L G-5 EBSE-6-SC EBSE-6-SZP EBSE-6-SZP EBSE-6-SZP EBSE-6-SZP

103V L-1/2 EBQE-AA-SC EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP 104V L-3/4 EBQE-AA-SC EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP 105V L-1 EBQE-AA-SC EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP EBQE-AA-SZP 206V L-1 EBQE-A-SC EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP 208V L-1 1/2 EBQE-A-SC EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP 209V L-2 EBQE-A-SC EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP EBQE-A-SZP 312V L-2 EBQE-A-SC EBQE-A-SZP EBQE-A-SZP EBQE-B-SZP EBQE-B-SZP 315V L-2 1/2 EBQE-B-SC EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP 416V L-2 1/2 EBQE-B-SC EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP EBQE-B-SZP 419V G-3 EBQE-B-SC EBQE-B-SZP EBQE-C-SZP EBQE-C-SZP EBQE-C-SZP 523V G-4 EBQE-C-SC EBQE-C-SZP EBQE-C-SZP EBQE-C-SZP EBQE-C-SZP 627V G-5 EBQE-C-SC EBQE-C-SZP EBQE-C-SZP EBSE-6-SZP EBSE-6-SZP

FACTOR Y INSTALLED

R404A

NOZZLE

0° F (-18° C) EVAP. -10° F (-23° C) EVAP. -20° F (-29° C) EVAP. -30° F (-34° C) EVAP. -40° F (-40° C) EVAP.

Above selections based on:

1) 100°F (38°C) vapor free liquid entering expansion valve

2) 110°F (43°C) Condensing temperature

3) 8 -12°F (4.4 -6.7°C) evaporator TD

Page 31

TLP

27/04/16

T30-TLP-PDI-17

- 31 -

INSTALLATION INSTRUCTIONS

INSTALLATION

The installation and start-up of evaporators should only

be performed by qualied refrigeration mechanics.

This equipment should be installed in accordance with all applicable codes, ordinances and local by-laws.

INSPECTION

Inspect all equipment before unpacking for visible signs of damage or loss. Check shipping list against material

received to ensure shipment is complete. IMPORTANT: Remember, you, the consignee, must

make any claim necessary against the transportation company. Shipping damage or missing parts, when discovered at the outset, will prevent later unnecessary and costly delays.

If damage or loss during transport is evident, make claim to carrier, as this will be their responsibility, not the manufacturer’s.

Should carton be damaged, but damage to equipment is

not obvious, a claim should be led for “concealed

damage” with the carrier. IMPORTANT: The electrical characteristics of the unit

should be checked at this time to make sure they correspond to those ordered and to electrical power available at the job site.

Save all shipping papers, tags and instruction sheets for reference by installer and owner.

APPLICATION

LP evaporators are designed for walker-in cooler and freezer applications used with wide range of refrigerants. For room temperatures above 35°F (2 °C) AND evaporating temperatures above 26°F (-3 °C), positive defrosting means (with electric or hot gas) may not be required, otherwise, electric defrost or hot gas defrost models should be used. Electric defrost models come with defrost termination and fan delay as standard to control the defrost cycle termination and fan delay, while defrost initiation means (e.g. defrost timer) is not included.

The coil must not be exposed to any abnormal atmospheric or acidic environments. This may result in corrosion to the cabinet and possible coil failure (leaks). (Consult manufacturer for optional baked on phenolic

protective coatings).

LOCATION

The unit location in the room should be selected to ensure uniform air distribution throughout the entire space to be refrigerated. Be sure that the product does not obstruct the free circulation of air. Allow a minimum of 24” clearance at each end. Do not locate evaporators over doors. Consideration should be given to the coil location in order to minimize the piping run length to the

condensing unit and oor drain.

EXPANSION VALVE (TXV) SELECTION

All units require the use of an externally equalized expansion valve. (A 1/4” (6 mm) O.D. equalizer line has been provided on the coil) TX valves should not be selected strictly by their nominal ton rating. (This rating

is based at a specic pressure di󰀨erential and entering liquid temperature). Since applications will di󰀨er it is

suggested the following selection procedure be followed.

1. Determine actual evaporator capacity. The nominal rating is based at 10°F T.D. (5 .6°C) (Entering Air Temp. minus Evap. Temp.) Note that a higher / lower operating T.D.will increase / decrease this capacity rating by their direct ratio within a range of 8 to 12°F (4 .4 to 8.3°C) T.D.

2. Determine the pressure drop across the valve by subtracting the evaporating pressure and distributor pressure drop from the high side liquid pressure. The distributor pressure drop is typically in the range of 20 to 35 psig (1.4 to 2.4 bar) depending on the type of refrigerant and operating conditions.

3. Estimate entering liquid temperature. Temperatures lower than 100°F (38 °C) increase valve capacity ratings. Refer to valve manufacturer’s specs for details.

4. Select valve from the valve manufacturer selection charts for the appropriate refrigerant, evaporating temp and pressure drop.

For best performance, the outlet of the expansion valve should be installed directly to the distributor body. If this is not possible, a straight tube up to 12 inches may be used for the connection.

Locate the expansion valve bulb on a horizontal length of suction line preferably 3 to 6 inches from the suction header. Locate the bulb at 4 or 8 clock position and insulate with a waterproof type of insulation. Clamp the bulb to ensure 100% contact of the bulb with the suction line.

Ensure appropriate nozzle has been installed in the distributor before installing valve. After following the manufacturer’s installation instructions and after the room has reached the desired temperature the valve

superheat should be checked. This will conrm that

the evaporator is operating properly and performing to

maximum e󰀩ciency. The superheat should be around

6 (3.3 °C) to 8°F (4.4 °C) for a 10 to 12°F T.D (5.6 to

6.7 °C). Too high or low a super heat will result in

unsatisfactory system performance and possible compressor problems.

Page 32

INSTALLATION INSTRUCTIONS

27/04/16

T30-TLP-PDI-17

- 32 -

TLP

NOZZLE INSTALLATION

For common applications (Medium temp. R404A, R22, R407A, 8 to 12°F (4 .4 to 6.7°C) T.D.; low temp. R404A/ R407A, 8 to 12°F (4 .4 to 6.7°C) T.D.) the nozzle for all

models has been factory installed. For other applications, refer to nozzle manufacturer’s selection guide. To replace a nozzle, the nozzle retainer clip (in distributor) must be removed before inserting nozzle. Re-install clip ensuring nozzle is properly in place. A small nozzle can be drilled larger using the drill size listed in table on page

23. Ensure the hole must be accurately centered and smooth. A lathe is preferred for the drilling.

To prevent freeze-up when the temperature of the refrigerated space is 35 should be heated along its run inside the cold room. The heated drain line should be insulated. It is recommended that the heater be energized at all times. A heat input of 20 watts per foot in a 28°F (-2°C) room and 30 watts per foot for -20°F (-29°C) rooms, is satisfactory. Drain line heaters are not required for constant room temperature above 35°F (2°C). Always trap evaporator drain line individually to prevent vapor migration.

F (2 °C) or lower, the drain line

MOUNTING

Refer to dimensional drawing for recommended mounting arrangements. Ensure adequate clearance is provided behind the coil as well as each end. The evaporators may

be mounted ush with ceiling with bolts, or hanging down

with rod hangers. When using rod hangers, allow adequate space between the top of the unit and the ceiling for cleaning to comply with NSF Standard 7.

Ensure that the ceiling is level since the drain pan has been sloped for drainage during the defrost

cycle.

DRAIN LINE

The drain line should be run from the drain connection, sloping at least 1” (25 mm) per foot and should have the size at least as large as the drain connection. A trap in a warm area outside the room must be provided to allow proper draining through the tubing. Connection should be made to proper drainage facilities that comply with local regulations.

Ensure that the drain line has su󰀩cient slope for

proper drainage (prevention of ice build up/blockage in pan).

PIPING

Refrigeration grade piping must be used for all eld

refrigeration piping. Refrigerant line sizes are important and may not be the same size as the coil connections. Consult ASHRAE handbook or other similar reference book for proper line sizing. Refrigerant piping and control system should be designed to prevent possible liquid slugging (from oil or refrigerant) of the compressors on start-up after the defrost cycle. Also, it should prevent oil logging and minimize refrigerant

pressure drop. For hot gas models, refer to pages 33 - 34 for

recommended piping.

Page 33

TLP

27/04/16

T30-TLP-PDI-17

- 33 -

INSTALLATION INSTRUCTIONS

WIRING

Wire system in accordance with governing standards and local codes. See data and wiring diagrams on pages 4 to 20 for typical wiring arrangement. Electrical wiring is to be sized in accordance with minimum circuit ampacity rating (MCA). Size fuses used must not exceed the Maximum

Fuse Size ratings.

For ease of identifying the proper wiring terminal, unit wiring is color coded and terminal block connections are

identied.

When fan delay thermostats (combination fan delay and defrost termination) are installed, on start-up, the fans do not operate until the coil temperature is reduced to approximately 25oF (-4°C). It is normal for the fans to cycle a few times until the room temperature is brought down. At higher evaporating temperatures this control may not close and therefore should either be by-passed temporarily or replaced with an adjustable type. (set for a higher temperature cut-in point).

MAINTENANCE

The unit should be periodically inspected for any dirt or

ice build-up on the n surface and cleaned if

necessary with a soft whisk or brush. Also ensure coils inner (and outer) drain pans do not have any ice build-up from improper defrost operation. When replacing heater

elements rst remove heater retainer brackets and heater

clips.

SYSTEM CHECK

Before Start-Up:

1. All wiring should be in accordance with local codes.

2. Refrigerant lines should be properly sized.

3. All systems preferably include a liqud line solenoid valve at immediately up stream of the expansion valve.

4. Thorough evacuation and dehydration has been performed.

5. The suction, discharge, and receiver service valves must be open.

6. The system preferably include a liquid line lter drier moisture indicator and suction lter.

7. Pour enough water into the drain pan to allow a good check on drainage and seal the trap.

After Start-Up:

1. Check the oil level to be sure the oil charge is correct.

2. On initial start up the fans do not start until coil temperature is pulled down to approximately 25°F (-4 °C) on the coil. Also, it is normal for the fan to cycle a few times until the room temperature is pulled down.

3. If necessary, temporarily by-pass fan delay control (to run fans until room temp is lowered).

4. Be sure that the expansion valve is properly set to provide the correct amount of superheat.

5. After the box temperature is close to reaching the desired temperature, the evaporator superheat must be checked and adjustment made if necessary.

In general, evaporators running with a TD of 10°F (5.6 °C ) should have a superheat reading of 6° to 8°F (3.3 °C to 4.4 °C). For evaporators with another T.D., the general rule is that the superheat should be around 60 to 80% of T.D.

6. Heavy moisture loads are usually encountered

when starting the system for the rst time. This may

cause a rapid build-up of frost on the evaporator. During the initial pull down, we suggest that the frost build-up be watched and defrosted manually as required.

7. Observe that the system goes through at least one complete DEFROST CYCLE.

Page 34

HOT GAS PIPING SCHEMATICS

WITH HOT GAS DRAIN PAN LOOP

WITH CHECK VALVE LOOSE

HOT GAS

LEAVING

DEFROST LOOP

HOT GAS DRAIN PAN

VALVE

CHECK

REVERSE CYCLE DEFROST

EVAPORATOR COIL

DISTRIBUTOR

STD-R

FACTORY PIPING

HOT GAS

ENTERING

LEAVING

HOT GAS

WITH CHECK VALVE LOOSE

REVERSE CYCLE DEFROST

ELECTRIC DRAIN PAN HEATER

EVAPORATOR COIL

DISTRIBUTOR

STD-G

FACTORY PIPING

CHECK

VALVE

WITH DRAIN PAN HEATER

WITH CHECK VALVE LOOSE

WITH HOT GAS DRAIN PAN LOOP

STD-H

DEFROST LOOP

HOT GAS DRAIN PAN

HOT GAS

LEAVING

VALVE

CHECK

EVAPORATOR COIL

3-PIPE DEFROST

DISTRIBUTOR

FACTORY PIPING

ENTERING HOT GAS

WITH CHECK VALVE LOOSE

VALVE

CHECK

STD-T

EVAPORATOR COIL

ELECTRIC DRAIN PAN HEATER

3-PIPE DEFROST

ENTERING HOT GAS

DISTRIBUTOR

LEAVING

HOT GAS

FACTORY PIPING

WITH DRAIN PAN HEATER

27/04/16

T30-TLP-PDI-17

- 34 -

TLP

Refer to Nomenclature for details

STANDARD CONFIGURATIONS

Standard O󰀨ering: All Models

Check Valve is included with the coil shipped loose as it is a must have component for system operation.

Check Valve & TXV - See next page (OPT 1)

When a TXV is ordered with a HG defrost coil: Its only option will be Factory Installed. The bypass check valve will be factory installed as well as part of the same option.

• Reverse Cycle PanHeater (G Models) when ordered with TXV & Check Valve: o TXV, Check Valve and bypass Tee are factory installed

• Reverse Cycle PanLoop (R Models) when ordered with TXV & Check Valve: o TXV, Check Valve and bypass Tee are factory installed

• 3-Pipe PanHeater (T Models) when ordered with TXV & Check Valve: o TXV and Check Valve are factory installed

• 3-Pipe PanLoop (H Models) when ordered with TXV & Check Valve: o TXV and Check Valve are factory installed

Page 35

HOT GAS PIPING SCHEMATICS

COMPLETE ASSY PROVIDED WHEN TXV IS MTD

WITH HOT GAS DRAIN PAN LOOP

CHECK VALVE MOUNTED

CHECK

DEFROST LOOP

HOT GAS DRAIN PAN

VALVE

REVERSE CYCLE DEFROST

EVAPORATOR COIL

DISTRIBUTOR

TXV

OPT1

FACTORY PIPING

LEAVING

HOT GAS

CHECK VALVE MOUNTED

COMPLETE ASSY PROVIDED WHEN TXV IS MTD

REVERSE CYCLE DEFROST

ELECTRIC DRAIN PAN HEATER

EVAPORATOR COIL

DISTRIBUTOR

CHECK

VALVE

TXV

OPT1

FACTORY PIPING

LEAVING

HOT GAS

WITH DRAIN PAN HEATER

ASSEMBLED OUTSIDE CABINET

WITH HOT GAS DRAIN PAN LOOP

CHECK VALVE MOUNTED

COMPLETE ASSY PROVIDED WHEN TXV IS MTD

HOT GAS DRAIN PAN

DEFROST LOOP

& SHIPPED SEPARATELY

REVERSE CYCLE DEFROST

EVAPORATOR COIL

CHECK

VALVE

DISTRIBUTOR

TXV

FACTORY PIPING FIELD PIPING

ENTERING HOT GAS

OPT2

LEAVING

HOT GAS

CHECK

VALVE

OPT1

HOT GAS DRAIN PAN

DEFROST LOOP

(SUCTION LINE)

LEAVING HOT GAS

ENTERING HOT GAS

FACTORY PIPING

WITH HOT GAS DRAIN PAN LOOP

WITH TXV BY OTHERS OR FACTORY INSTALLED

WITH CHECK VALVE MTD. & CONNECTED TO LOOP

3 PIPE DEFROST

EVAPORATOR COIL

DISTRIBUTOR

TXV

CHECK

OPT1

WITH CHECK VALVE MOUNTED

WITH TXV BY OTHERS OR FACTORY INSTALLED

EVAPORATOR COIL

3 PIPE DEFROST

ELECTRIC DRAIN PAN HEATER

HOT GAS

(SUCTION LINE)

DISTRIBUTOR

LEAVING

CHECK

VALVE

TXV

FACTORY PIPING

ENTERING HOT GAS

27/04/16

T30-TLP-PDI-17

- 35 -

TLP

Refer to Nomenclature for details

OPTIONAL CONFIGURATIONS

Drain pan Loop Kit - See below (OPT 2)

Drain pan loop kit is an assembly that is fully assembled and shipped loose for eld installation outside the cabinet. Two check valves are included, depending on the model size, one or both are factory installed.

• Reverse Cycle PanLoop (R Models) when ordered with TXV & Check Valve: o Suction line piping shipped as a pre-piped assembly for eld installation

Solenoid Valve

Solenoid valves are available as a shipped loose item due to limited space inside the cabinet

Page 36

TLP

27/04/16

T30-TLP-PDI-17

- 36 -

GLYCOL FLUID AIR COOLER DATA

(Contact Factory for Complete Details)

60Hz

MODEL

104W 1 1010 (480) 2100 (620) 6.9 (20.7) 2500 (730) 17 (51.7) 7/8 106W 1 950 (450) 2800 (820) 3.2 (9.7) 3100 (910) 8.1 (24.1) 7/8 107W 1 900 (430) 3400 (1000) 4.4 (13.1) 3700 (1080) 4.6 (13.8) 7/8 209W 2 2020 (950) 3800 (1110) 10 (31.0) 5000 (1470) 25 (73.8) 7/8 211W 2 1910 (900) 4900 (1440) 4.8 (14.5) 5700 (1670) 12 (35.2) 7/8 214W 2 1800 (850) 5900 (1730) 6.5 (19.3) 6700 (1960) 6.9 (20.7) 7/8 317W 3 2860 (1350) 6600 (1930) 6.5 (19.3) 8000 (2340) 15 (46.2) 7/8 320W 3 2700 (1270) 8000 (2340) 8.8 (26.2) 9400 (2750) 9.2 (27.6) 7/8 423W 4 3810 (1800) 8100 (2370) 8.1 (24.1) 10000 (2930) 19 (57.2) 7/8 426W 4 3600 (1700) 9800 (2870) 11 (32.4) 12000 (3520) 11 (33.8) 7/8 532W 5 4500 (2120) 11000 (3220) 13 (38.6) 14000 (4100) 14 (40.7) 7/8 639W 6 5400 (2550) 13000 (3810) 15 (45.5) 16000 (4690) 16 (46.9) 7/8

The above capacities were rated based on 30% Propylene Glycol, 25°F (-4°C) glycol entering temperature and 35°F (-2°C) air entering term-

perature with glycol ow rate listed. For all other conditions, please use “Pi-Coil” software (contact factory).

NO. OF

FANS

AIRFLOW

CFM (L/S)

CAPACITY * - 5 USGPM (.032 L/S) CAPACITY * - 15 USGPM (.095 L/S)

BTU/H (WATTS)

P.D.

(FT. H

P.D.

(kPa)

BTU/H (WATTS)

P.D.

(FT. H20)

P.D.

(kPa)

CONN.

SIZE (IN/

OUT)

Page 37

TLP

27/04/16

T30-TLP-PDI-17

- 37 -

SERVICE PARTS

60Hz

FOR SERVICE PARTS LOOK-UP:

visit: http://www.t-rp.com/serv_parts.htm

email: parts@t-rp.com

call: 1-844-893-3222 x501

Page 38

NOTES

27/04/16

T30-TLP-PDI-17

- 38 -

Page 39

FINISHED GOODS WARRANTY

27/04/16

T30-TLP-PDI-17

- 39 -

The terms and conditions as described below in the General Warranty Policy cover all products manufactured by National Refrigeration.

GENERAL WARRANTY POLICY

Subject to the terms and conditions hereof, the Company warrants all Products, including Service Parts, manufactured by the Company to be free of defects in material or workmanship, under normal use and application for a period of one (1) year from the original date of installation, or eighteen

(18) months from the date of shipment from the Company, whichever occurs rst. Any replacement

part(s) so supplied will be warranted for the balance of the product’s original warranty. The part(s) to be replaced must be made available in exchange for the replacement part(s) and reasonable proof

of the original installation date of the product must be presented in order to establish the e󰀨ective date of the warranty, failing which, the e󰀨ective date will be based upon the date of manufacture plus

thirty (30) days. Any labour, material, refrigerant, transportation, freight or other charges incurred in connection with the performance of this warranty will be the responsibility of the owner at the cur-

rent rates and prices then in e󰀨ect. This warranty may be transferred to a subsequent owner of the

product.

THIS WARRANTY DOES NOT COVER

(a) Damages caused by accident, abuse, negligence, misuse, riot, re, ood, or Acts of God (b) damages

caused by operating the product in a corrosive atmosphere (c) damages caused by any unauthorized

alteration or repair of the system a󰀨ecting the product’s reliability or performance (d) damages caused

by improper matching or application of the product or the product’s components (e) damages caused by failing to provide routine and proper maintenance or service to the product (f) expenses incurred for the erecting, disconnecting, or dismantling the product (g) parts used in connection with normal maintenance,

such as lters or belts (h) products no longer at the site of the original installation (i) products installed

or operated other than in accordance with the printed instructions, with the local installation or building codes and with good trade practices (j) products lost or stolen.

No one is authorized to change this WARRANTY or to create for or on behalf of the Company any other obligation or liability in connection with the Product(s). There is no other representation, warranty or condition in any respect, expressed or implied, made by or binding upon the Company other than the above or as provided by provincial or state law and which cannot be limited or excluded by such law, nor will we be liable in any way for incidental, consequential, or special damages however caused.

The provisions of this additional written warranty are in addition to and not a modication of or subtraction

from the statutory warranties and other rights and remedies provided by Federal, Provincial or State laws.

PROJECT INFORMATION

System Model Number Date of Start-Up

Serial Number Service Contractor Refrigerant Phone Electrical Supply Fax

Page 40

“AS BUILT” SERVICE PARTS LIST

27/04/16

Service Parts List

Label

To Be Attached

HERE

NATIONAL REFRIGERATION & AIR CONDITIONING CANADA CORP.

159 Roy Blvd. Brantford Ontario Canada N3R 7K1 PHONE: (519) 751-0444 800-463-9517 FAX (519) 753-1140 www.t-rp.com

Due to National Refrigeration’s policy of continuous product improvement, we reserve the right to make changes without notice.

Control Products 104L Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual