Control Company WATERPROOF COUNTDOWN TIMER User Manual

SPECIFICATIONS

Timing capacity: 99 minutes 59 seconds.
Battery: silver-oxide button cell

COUNT-UP TIMING

The unit counts up to 99 minutes 59 seconds. Once the
timer reaches 99 minutes 59 seconds it starts the timing
over again from 00 minutes 00 seconds.

COUNTDOWN ALARM TIMING

1. Press the MIN and SEC buttons simultaneously to
clear the display to zero.

2. Press the MIN (minutes) button to advance the
minutes digits. Press and hold down the MIN
button to rapidly advance the minutes.

3. Press the SEC (seconds) button to advance the
seconds digits. Press and hold down the SEC
button to rapidly advance the seconds.

4. Once the desired time is on the display, press the
START/STOP button to begin countdown timing.

5. When the timer reaches zero, an alarm will sound.
The alarm will sound for one minute and then turn off
automatically to preserve battery life.

While the alarm is sounding, pressing the START/STOP
button will silence the alarm, stop the count-up timing,
and recall the last programmed time. After one minute,
pressing the START/STOP button will stop the count-up
timing and recall the last programmed time.

MEMORY RECALL

When timing repetitive intervals, the memory function
will recall the last programmed time. This feature
allows the timer to be dedicated to a frequently timed
test. The timer will return to the last programmed time
again and again.

1. Follow steps 1 through 5 in the “Countdown Alarm
Timing” section.

2. When the alarm starts, press the START/STOP
button to stop the alarm and recall the last
programmed time.

3. Press the START/STOP button a again to begin
countdown timing.

CLEARING THE DISPLAY TO ZERO

If an error is made during an entry, press the MIN and
SEC buttons simultaneously to clear the display to zero.
To clear the display to zero when time is running, press
the MIN and SEC buttons simultaneously.

STOPWATCH (COUNT-UP) TIMING

1. Clear the display to zero (simultaneously press
the MIN and SEC buttons).

2. Press the START/STOP button to begin count-up
timing.

3. Press the START/STOP button to stop count­ up timing.

Once timing is completed and the timer has stopped,
press the MIN and SEC buttons simultaneously to clear
the display to zero.

TIMEOUT

The timer may be started or stopped during any running
time by pressing the START/STOP button.

CONVERT A TIMEOUT TO A COUNTDOWN TIME

Once the timing has been stopped, pressing the MIN
or SEC button will increment the display from the point
that it was stopped and will set the timer into countdown
mode. Once the desired time is on the display, press the
START/STOP button to begin countdown timing.

REMOVABLE SUCTION CUP

To remove the suction cup located on the back of the
timer. Flip the timer over, so the back is facing up. Gently
pull the suction cup to the right, and the suction cup will
pop out.

To replace the suction cup. Place the ball of the suction
cup into the larger end of the mounting slot. Gently pull
the suction cup to the left, and the suction cup will pop in.

ALL OPERATIONAL DIFFICULTIES

If this timer does not function properly for any reason, re­place the battery with a new high quality battery (see the
“Battery Replacement” section). Low battery power can
occasionally cause any number of “apparent” operational

difculties. Replacing the battery with a new fresh battery
will solve most difculties.

BATTERY REPLACEMENT

An incorrect display, no display or operational difculties

indicate that the battery should be replaced. Using a
small screwdriver, unscrew the four screws located on
the back of the timer. Remove the battery cover. Remove
the exhausted battery and replace it with a new 1.5 volt
silver-oxide 357 size battery. Make certain the positive (+)
side is visible. Replace the battery cover. Screw the four
screws back into the unit. Do not over-tighten the screws
as this may cause damage to the battery cover.

WARRANTY, SERVICE, OR CALIBRATION

For warranty, service, or calibration contact:

CONTROL COMPANY

4455 Rex Road

Friendswood, Texas 77546 USA

Ph. 281 482-1714 • Fax [phone]

www.control3.com • [e-mail]

Control Company is ISO 9001 Quality-Certied by DNV and

ISO 17025 accredited as a Calibration Laboratory by A2LA

Control Company Cat. No. 5200

®

is a registered trademarks of Control Company.

Traceable

2013 Control Company. 92-5200-00 Rev. 0 073013

©

TRACEABLE

WATERPROOF

COUNTDOWN

TIMER

INSTRUCTIONS

®