Control Company WALKAWAY REPEAT CONTROLLER User Manual

TRACEABLE® WALKAWAY™ REPEAT CONTROLLER INSTRUCTIONS

SPECIFICATIONS

Power: 120 VAC, 60 HZ, 3-pronged grounded plug Switching Capability: 120 VAC, 60 Hz, 1800 watts, 15 amps,

1/3 horsepower Timing Accuracy: 0.01% Timing Ranges: Repeat ON/OFF – 1 hour to 99 hours (H) 1 minute to 99 minutes (M) 1 second to 99 seconds (S) Display: ½-inch (1.3 cm) LCD with backlighting Size: 6 x 2¾ x 3¼ inches Weight: 12 oz. Case: High-impact, ABS plastic Cat. No.: 5058 – Traceable

NOTE: Remove clear plastic COVER by gently lifting one edge with a

paper clip before programming unit. If there is a clear plastic film over face plate, remove and discard. Use COVER to protect against accidental setting changes during timings and to protect keys when unit is not in use.

NOTE: Receptacle outlet on back of unit has power only during count up

ON timing.

DIGITAL DISPLAY AND LIGHTS

1. Steady red light on case indicates controller is receiving power.

2. Flashing red lights indicates ON/OFF timing is in progress.

3. HMS switch above red light sets timing hours H, minutes M, or seconds

4. Yellow PAUSE button pauses timing.

5. Blue START/STOP button starts/stops timing.

6. Blue buttons SET, 4/3, 2/1 set hours, minutes, or seconds for desired

programmed time.

7. Blue RST button resets unit and returns display to 00.00.

LCD display is divided into four areas:

A. Displays programmed ON time

B. Displays elapsed count up ON time

C. Displays programmed OFF time

D. Displays elapsed count up OFF time

OPERATION

1. Plug unit into power source. Red light will turn on.

2. Plug desired equipment into receptacle outlet on back of unit.

3. Remove clear plastic cover by gently lifting one edge with a paper clip.

4. To return display to 00.00, gently press RST with a stylus or the end of

a bent paper clip. Or, move HMS switch to another position and then back to desired setting. (Example: HMS switch is set at H. Move switch to M and then back to H. Display will return to 00.00.)

5. Move HMS switch to desired time using a stylus or the end of a bent

paper clip – hours (H appears on display), minutes (M appears on display), or seconds (S appears on display).

6. Press and hold SET button for three seconds. Display will flash.

7. Press 4 and 3 to set desired ON time. Press and hold button to

advance setting rapidly.

Repeat Walkaway™ Controller

8. Press 2 and 1 to set desired OFF time. Press and hold button to advance setting rapidly. Press SET or PAUSE when desired programmed time is on the display. Or, wait 8 seconds until display stops flashing to lock in programmed time.

9. IMPORTANT NOTE: Both an ON and an OFF time MUST be set for the unit to function correctly.

10. Press START/STOP to begin timing. Red light will continue to flash during ON/OFF timing. Equipment only has power during ON timing.

11. Bar "—" on display appears above ON when ON-timing is in progress. Bar "—" appears above OFF when OFF-timing is in progress.

12. Unit will continue to repeat ON/OFF programmed timing. To stop timing, press START/STOP. Elapsed time returns to 00.00. Red light stops flashing and is continuously ON.

13. Press and hold the buttons 1, 2, 3 and 4 simultaneously for 3 seconds to lock in a set time. A “ of the display. Repeat this step to unlock the set time.

NOTE: When the “ changed, even by pressing the RST key.

TIME-OUT

Press PAUSE to stop timing. Press PAUSE again to resume timing. Any number of time-outs may be taken during a timing.

NOTE

Pressing START/STOP while time is running will stop timing and return count up display to 00.00.

NOTE

1. If electrical power is interrupted at any time, unit will turn OFF. Internal rechargeable battery will continue to light display.

2. During any interruption of electrical power, count up time elapsed will return to 00.00. Programmed time will remain on display.

3. After power is restored, to re-activate unit and re-start programmed ON/OFF timing, press START/STOP.

TROUBLESHOOTING: Make certain both an ON and an OFF time are programmed. Unit will not function with only an ON time programmed.

” will appear in the lower left-hand corner

” is on the display, the set time cannot be

WARRANTY, SERVICE, OR RECALIBRATION

For warranty, service, or recalibration, contact:

CONTROL COMPANY

4455 Rex Road

Friendswood, Texas 77546 USA

Ph. 281-482-1714 Fax 281-482-9448

E-mail sales@control3.com

www.control3.com

Control Company is ISO 9001 Quality-

Certified by DNV and ISO 17025 accredited

as a Calibration Laboratory by A2LA.