Control Company THERMOMETER WITH TIME DATE MAX MIN MEMORY User Manual

TRACEABLE®

SPECIFICATIONS

Range: –40° to 176°F / –40° to 80°C (probe) 14° to 176°F / –10° to 80°C (ambient) Resolution: 0.1°

OPERATION

1. Remove the battery and re-insert it to set the clock on the unit. After the segment test has been run, the minutes counter wi ll flash. Set the minutes by pressing the MIN/MAX butt on. Press and hol d the MIN/MAX button to increase the minute counter rapidly until the button is released. Press the IN/ DATE butt on to conf i rm the correct minut e setting.

2. The hour counter will begin flashing. Set the hour by pressing the MIN/MAX button. Press and hold the MIN/MAX button to i ncreas e the hour counter rapidly unti l t he butt on is releas ed. Press the IN/DATE button to confirm the correct hour sett ing.

3. The mont h indicator will begin flashing. Set the month by pressing the MIN/MAX button. Press and hold the MIN/MAX button to i ncreas e the counter rapidly unti l t he butt on is releas ed. Press t he IN/DATE button to confirm the correct mont h sett i ng. If no butt on is pressed f or 15 seconds, the unit will be set and will begin recordi ng temperature.

4. To select °F or °C, slide the switch located on the back of the unit to the desired setting.

5. To s witch the display between date and indoor temperature, press the IN/DATE button. While in date mode, “DATE” wi ll appear on the display. Whil e in ambient temperat ure m ode, “I N” wi ll appear on t he display.

6. To recall the stored memories, press the MIN/MAX button repeatedly and the display will indicate the following: Maximum outdoor temperature Minimum outdoor temperature Maximum indoor temperature Minimum indoor temperature The display will also show the correspondi ng date and t ime that the MIN/MAX readings occurred. P ress t he MIN/MAX butt on again to return to the current temperature mode.

7. To delete a minimum/maximum memory, press and the MIN/MAX button until the desired memory is displ ayed. Press the IN/DATE button and the displayed memory will be cleared. Repeat this process to clear each desired memory.

BENCH STAND

The unit is supplied with a bench stand that is a part of the batt ery c over. To use the bench stand, locate the small opening at the bott om of the unit. Place your fingernail into the opening and flip the stand up. To close the stand, simply snap it shut.

WALL MOUNTI NG THE UNI T

Set two screws into the wall at the desired locat i on. Do not set the screw flush to the wall; the heads of the screws will need to sli p into the rec eptac les on the back of the unit. Once the screws have been properly set, hang the unit in place by sliding the receptacles on the back of the unit over the heads of the screws.

THERMOMETER WITH TIME/DATE MAX/MIN MEMORY

ALL OPERATI ONAL DIFFICULTIES

If this unit does not function properly for any reason, replace the battery with a new high quality battery (see “Battery Replacement” section). Low battery power can occasionally cause any number of “apparent ” operational difficult ies. Replacing the battery with a new fresh battery will solve most difficulties.

BATTERY REP L ACEM ENT

Erratic readings, faint readings, or no di splay are all i ndications that the battery must be replaced. R em ove the battery cover. Remove the exhausted bat tery and replace with a new AAA alkaline batt ery. Replace t he battery c over making certai n to run the probe c able through the slot on the right or left bottom side of t he battery c over. Upon initial i nstallation of the battery, the time and date will require set ting. (See th e “Operation” section.)

WARRANTY, SERVICE, OR RECALIBRATION

For warranty, service, or recalibration, contact:

Friendswood, Texas 77546 USA

Ph. 281-482-1714 Fax 281-482-9448

Control Company is ISO 9001 Quality-

Certified by DNV and ISO 17025 accredited

as a Calibration Laboratory by A2LA.

INSTRUCTIONS

CONTROL COMPANY

4455 Rex Road

E-mail sales@control3.com

www.control3.com

Control Company Cat. No. 4105, 4305 & 4605