Control4 WA2200 Users Manual

WA-2200-C, WA-2200-C-1

802.11ac 2x2 Wave 2 Access Point,
In-Ceiling

BakPak

Lite

QUICK START GUIDE

WA-2200-C features

Mounting into the bracket

• 802.11ac 2x2 Wave 2 Access Point, In-Ceiling

• Built-in 2×2 internal antennas

• Powered by PoE (or 12VDC 1A power adapter, not included)

• 1 Gigabit LAN port

• BakPak Lite built in: Manage device from the standard BakPak interface

• For more detailed instructions, refer to the WA-2200 User Guide
(

pkdge.co/wa2200-ug

).

System requirements

• Windows or Mac PC with an Ethernet interface

Default settings and credentials

• Operation mode: Access Point

• IP address: If no DHCP server is detected, the default IP address will be
automatically set to 192.168.1.21.

• Username/Password (default): admin/password

• SSIDs (default): Pakedge-Main (5 GHz), Pakedge-Alt (2.4 GHz), security/
password: WPA2-PSK/pakedgewireless

• Guest SSIDs (default): PakedgeGuest2.4 and PakedgeGuest5, security/password:
WPA2/pakedgeguest

• Transmit power: Default is 13dBm for 2.4GHz and 18 dBm for 5 GHz.

2 32 3

1 Place the included template against the ceiling or wall at the desired location,

then cut along the dotted line with a drywall saw.

2 To mount the access point into the bracket, review the visual guide that follows:

Powering up

The access point can be powered only by either PoE or the optional AC power adapter
(not included).

To power up the access point:

1 Connect power using a POE injector or POE switch, or with the optional AC

power adapter (not included).
The access point should now be up and running with its default settings. It does

not need to be configured to be functional. To make changes to the SSID and
security settings, you need to access the AP’s interface using a web browser.

4 54 5

Logging in to the access point

Registering your device with BakPak Lite

To log in to the access point:

1 Connect the access point to your PoE switch with an Ethernet cable.
2 Log in to your router to find the IP address assigned to the access point under

the DHCP Client Table, then enter into a web browser (or click) that IP address to
open the access point interface. The Log In page opens.

Tip: If you do not have a router in your network that distributes IP addresses, you
can try to access the access point through its default IP address of 192.168.1.21.

3 In the username box, type admin. In the password box, type password, then click

Log in. The first time you log in, the Configure page opens.

4 Enter and verify a new password (required) before continuing, then click Apply to

complete the setup.

Caution: For international models, you must change the Country Code (a drop-down

list defaulting to GB - United Kingdom), to the specific country of operation.

6 76 7

You can connect your access point to your existing BakPak account or create a new
account to manage all of your BakPak network management agents.

To register your device to your BakPak account:

1 In the device’s Connections tab, to the right of the “This product is not managed

by BakPak” message, click Click here to enroll.

The BakPak Registration page opens.

2 Follow the on-screen instructions to complete your device registration.

Adding more WA Series APs to the BakPak site

Adding WA Series APs to the site

To manage and set up more than one WA-2200, a BakPak site must be created to
manage them as a group.

To create a BakPak site:

1 Log in to your BakPak account, then click Add Site to create a site.
2 In the Management Agent list, select the first WA-2200, complete the site

information, then click OK.

The site is created, and the WA-2200 will act as the “master AP” for adding more
WA Series APs to the site.

8 98 9

To add APs and provision them with the existing configuration:

1 Make sure that the first AP is already configured, and that the additional APs are

turned on for at least five minutes and connected to your network.

2 In BakPak, select the new WA-2200 site, then click Device Discovery.

Any additional WA Series APs are discovered and appear as tiles that can be
selected (already selected by default).

3 Click OK. The APs are added to the site.
4 To apply the first AP’s settings to the new APs, in the BakPak site select the first

AP you set up (on the previous page), then complete the site information and
click Save & Apply Multiple at the bottom. The settings are copied to the APs.

Technical Support

For technical help:

www.pakedge.com/portal

[e-mail]

[phone]

For regulatory information:

www.pakedge.com/regulatory

11734 S. Election Road
Draper, UT 84020
Main: [phone] Fax: [phone]

www.pakedge.com
[e-mail]
©2018 Control4. All rights reserved.

Latest version at

pkdge.co/wa2200c-qsg

200-00577-B 2018-12-04 MS