Control4 C4SWTV User Manual

™

Switch Installation Guide

Supported Model

• C4-SW120277 Switch

Introduction

The Control4® Switch operates independently or as part of a Control4 home automation system. It installs in a standard back box using typical wiring standards and communicates to the Control4 system using a wireless connection.

Box Contents

• Switch

• Wire Nuts

• Warranty Card

• SwitchInstallationGuide (this document)

Speciﬁcations and Supported Load Types

The speciﬁcations are described below.

Model Number C4-SW120277-xx

Power Requirements 110-277VAC +/-10%, 50/60Hz

This device requires a neutral connection. See the “Sample Wiring Conﬁgurations” later in this guide.

Power Consumption 120V: 400mW

277: 1150mW

Load Types and Ratings

Supported Load Types Incandescent, Halogen, Electronic (Solid

State) Low Voltage (ELV) transformers, Magnetic (Iron Core, Inductive) Low Voltage (MLV) transformers, Fluorescents, Compact Fluorescents, LEDs, Motors

Maximum Load 120V: 15A, 1/2HP

277V: 8A, 1/2HP

Environmental

Operational Temperature 32˚ F - 104˚ F (0˚ C - 40˚ C)

Humidity 5% to 95% non-condensing

Storage -4˚ F - 158˚ F (-20˚ C - 70˚ C)

Miscellaneous

Control Communications ZigBee, IEEE 802.15.4, 2.4 GHz, 15-channel

spread spectrum radio

Wallbox Volume 5.75 cubic inches

Weight 0.12 lb (0.05 kg)

Shipping Weight 0.18 lb (0.08 kg)

Warnings and Considerations

WARNING! Turn OFF electrical power before installing or servicing this

product. Improper use or installation can cause SERIOUS INJURY, DEATH or LOSS/DAMAGE OF PROPERTY.

ATTENTION! Coupez l’alimentation électrique avant d’installer ou de

réparer ce produit. Une mauvaise installation ou utilisation peut entraîner des blessures graves, décès ou perte / dommages à la propriété.

WARNING! This device must be protected by a circuit breaker (20A max). ATTENTION! Cet appareil doit être protégé par un disjoncteur (20A max.)

WARNING! Ground this device in accordance with the National Electric

Code (NEC) requirements. DO NOT rely solely upon the yoke plate’s contact with a metal back box for adequate grounding. Use the device’s ground wire to make a secure connection to the safety ground of the electrical system.

ATTENTION! Cet appareil doit être en conformité avec le Code national

de l’électricité (NEC). Ne comptez pas uniquement au contact de la plaque avant avec un boîtier mural métallique pour la mise à la terre adéquate. Utilisez cet appareil à la terre de l’appareil pour établir une connexion sécurisée au système électrique.

IMPORTANT! This device must be installed by a licensed electrician in

accordance with all national and local electrical codes.

IMPORTANT! If you are unsure about any part of these instructions,

consult a qualiﬁed electrician.

IMPORTANT! Use this device only with copper or copper-clad wire. Do

not use aluminum wiring. This product has not been approved for use with aluminum wiring.

IMPORTANT! Using this product in a manner other than outlined in this

document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See “Troubleshooting.”

IMPORTANT! Do NOT use a power screwdriver to install this device. If you

do, you may overtighten the screws and strip them. Also, overtightening the screws may interfere with proper button operation.

IMPORTANT! This is an electronic device with intricate components.

Handle and install with care!

Installation Instructions

1 Ensure that the location and intended use meet the following criteria:

• Do not exceed the load capacity requirements of the switch. Refer to the load ratings in the speciﬁcations above for details.

• Install in accordance with all national and local electrical codes.

• The range and performance of the wireless control system is highly

dependent on the following: (1) distance between devices; (2) layout of the home; (3) walls separating devices; and (4) electrical equipment located near devices.

2 Turn o the local electrical power by either switching o the circuit breaker or

removing the fuse from the fuse box. To ensure the wires do NOT have power running to them, use an inductive voltage detector.

NOTE: The back box wiring shown in this document is an example. Your

wire colors and functions may dier. If you are not sure which wires are the Hot, Neutral, Load, Traveler, and Ground wires, have a trained electrician perform the installation.

3 Prepare each wire. Wire insulation should be stripped back 5/8 of an inch

from the wire end (see Figure 1).

Figure 1. Strip Wire Insulation

4 Identify your wiring application, and then see the appropriate wiring diagram

in the “Sample Wiring Conﬁgurations” section below.

IMPORTANT! Not grounding this product, as described in the section

“Warnings and Considerations,” may result in an installation less immune to damage caused by electrical disturbances, such as ESD or lightning, and may void the warranty.

5 Identify and connect the switch wires to the back box wires using the wire

nuts.

IMPORTANT! The yellow wire is not a traditional traveler. It cannot directly

power a lighting load. It must be used only to connect to a Control4 Auxiliary Keypad. See “Sample Wiring Conﬁgurations.”

TIP: If you are using a Control4 push-on (screwless) faceplate in a multi-

gang installation, attach the black faceplate sub-plate to all of the devices that will be installed into the wallbox prior to attaching the devices to the wallbox. This will help ensure that all the devices are properly aligned and on the same plane after installation.

6 Fit the wires back into the back box. Bend the wires in a zigzag pattern so

that they easily fold into the back box (Figure 2).

Figure 2. Bend the Wires

7 Align the switch to the back box (the load rating label should be at the

bottom) and fasten it with screws. Tighten the screws until the back side of the yoke plate is even with the wall surface, but no further. Overtightening can warp the dimmer and cause mechanical malfunction.

8 Install the Control4 Faceplate following the instructions in the Faceplate

Installation Guide or attach a standard Decora-style faceplate.

9 Turn ON power at the circuit breaker or replace the fuse

from the fuse box.

Operation and Conﬁguration

On initial power up, all status LEDs on the switch will illuminate green indicating that the device has power. To set up this switch for use with a Control4 system, refer to the Composer Pro User Guide.

To operate this switch as a stand-alone device:

• Click the top button to turn the light on.

• Click the bottom button to turn the light o.

Button Tap Sequences

The button tap sequences are deﬁned in the table below. Button tap sequences that require a single (1) button should use the top button.

Function Sequence Button

Identify 4

ZigBee Channel 7

Reboot 15

Factory Reset 9-4-9

Leave Mesh and Reset 13-4-13

Troubleshooting

If the light does not turn on:

• Ensure at least one LED on the face of the switch is lit.

• Ensure the light bulb is not burned out and is screwed in tightly.

• Ensure that the circuit breaker is not turned OFF or tripped.

• Check for proper wiring (see “Sample Wiring Conﬁgurations”).

• For help on the installation or operation of this product, email or call the

Control4 Technical Support Center. Please provide your exact model number. Contact support@control4.com or see the web site www.control4.com.

Care and Cleaning

• Do NOT paint the switch or its wall plate.

• Do NOT use any chemical cleaners to clean the switch.

• Clean surface of the switch with a soft damp cloth as needed.

Regulatory/Safety Information

To review Regulatory information for your particular Control4 products, see the information located on the Control4 website at: http://www.control4.com/ regulatory/.

Patent Information

Applicable patents are available at http://www.control4.com/legal/patents.

Warranty

For complete warranty information, including details on consumer legal rights as well as warranty exclusions, review the Warranty card or visit www.control4.com/ warranty.

About this Document

Part Number: 200-00310, Rev A 2/25/2013

™

Sample Wiring Conﬁgurations

Figure 3. Single Device Location

Figure 4. Multiple Device Location Using Auxiliary Keypad

Figure 5. Multiple Device Location Using Conﬁgurable Keypad

the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners Pricing and speciﬁcations are subject to change without notice

™

0-10V Dimmer Installation Guide

Warnings and Considerations

WARNING! Turn OFF electrical power before installing or servicing this

product. Improper use or installation can cause SERIOUS INJURY, DEATH or LOSS/DAMAGE OF PROPERTY.

ATTENTION! ATTENTION! Coupez l’alimentation électrique avant

d’installer ou de réparer ce produit. Une mauvaise installation ou utilisation peut entraîner des blessures graves, décès ou perte / dommages à la propriété.

3 Prepare each wire. Wire insulation should be stripped back 5/8 of an inch

from the wire end (see Figure 1).

Figure 1. Strip Wire Insulation

To operate this dimmer as a stand-alone device:

• Click the top button to turn the light on.

• Click the bottom button to turn the light o.

• Press and hold the top button to ramp the light up. Release the button at the

desired light level.

• Press and hold the bottom button to fade the light down. Release the button at the desired light level.

Button Tap Sequences

Supported Model

• C4-TV120277 0-10V Dimmer

Introduction

The Control4® 0-10V Dimmer operates independently or as part of a Control4 home automation system. It installs in a standard back box using typical wiring standards and communicates to the Control4 system using a wireless connection.

Box Contents

• 0-10V Dimmer

• Wire Nuts

• Warranty Card

• 0-10VDimmerInstallationGuide (this document)

Speciﬁcations and Supported Load Types

The speciﬁcations are described below.

Model Number C4-TV120277-xx

Power Requirements 110-277VAC +/-10%, 50/60Hz

This device requires a neutral AC connection. See “Sample Wiring Conﬁgurations” later in this guide.

Power Consumption 120V: 485 mW

277V: 1.18 W

Load Types and Ratings

Supported Load Types Four-wire 0-10V and 1-10V dimmable

Maximum Load (Switched Hot)

Maximum Load (0-10V

Control)

Operational Temperature 32˚ F - 104˚ F (0˚ C - 40˚ C)

Humidity 5% to 95% non-condensing

Storage -4˚ F - 158˚ F (-20˚ C - 70˚ C)

Control Communications ZigBee, IEEE 802.15.4, 2.4 GHz, 15-channel

Wallbox Volume 5.75 cubic inches

Weight 0.12 lb. (0.05 kg)

Shipping Weight 0.18 lb. (0.08 kg)

ﬂuorescent ballasts and LEDs, sink or source.

120V: 15A 277V: 8A

100mA sink or source

Environmental

All load ratings are based on an ambient temperature of 25˚ C

Miscellaneous

spread spectrum radio

WARNING! This device must be protected by a circuit breaker (20A max). ATTENTION! Cet appareil doit être protégé par un disjoncteur (20A max.)

WARNING! Ground this device in accordance with the National Electric

Code (NEC) requirements. DO NOT rely solely upon the yoke plate’s contact with a metal wallbox for adequate grounding. Use the device’s ground wire to make a secure connection to the safety ground of the electrical system.

ATTENTION! Cet appareil doit être en conformité avec le Code national

IMPORTANT! This device must be installed by a licensed electrician in

accordance with all national and local electrical codes.

IMPORTANT! If you are unsure about any part of these instructions,

consult a qualiﬁed electrician.

IMPORTANT! Use this device only with copper or copper-clad wire. Do

not use aluminum wiring. This product has not been approved for use with aluminum wiring.

IMPORTANT! To reduce the risk of overheating and possible damage

to other equipment, do not install to control a receptacle or a motoroperated appliance.

IMPORTANT! Using this product in a manner other than outlined in this

document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See “Troubleshooting.”

IMPORTANT! Do NOT use a power screwdriver to install this device. If you

do, you may overtighten the screws and strip them. Also, overtightening the screws may interfere with proper button operation.

IMPORTANT! This is an electronic device with intricate components.

Handle and install with care!

Installation Instructions

1 Ensure that the location and intended use meet the following criteria:

• Do not exceed the load capacity requirements of the dimmer. Refer to the load ratings in the speciﬁcations above for details.

• Install in accordance with all applicable national and local electrical codes.

• The range and performance of the wireless control system is highly

dependent on the following: (1) distance between devices; (2) layout of the home; (3) walls separating devices; and (4) electrical equipment located near devices.

2 Turn o the local electrical power by either switching o the circuit breaker or

removing the fuse from the fuse box. To ensure the wires do NOT have power running to them, use an inductive voltage detector.

NOTE: The back box wiring shown in this document is an example. Your

wire colors and functions may dier. If you are not sure which wires are the Hot, Neutral, Load, and Ground wires, have a trained electrician perform the installation.

4 Identify your wiring application, and then see the appropriate wiring diagram

in the “Sample Wiring Conﬁgurations” section below.

IMPORTANT! Not grounding this product as described in the section,

“Warnings and Considerations,” may result in an installation less immune to damage caused by electrical disturbances, such as ESD or lightning, and may void the warranty.

5 Identify and connect the dimmer wires to the back box wires using the wire

nuts.

IMPORTANT! The yellow wire is not a traditional traveler. It cannot directly

power a lighting load. It must be used only to connect to a Control4 Auxiliary Keypad. See “Sample Wiring Conﬁgurations.”

TIP: If you are using a Control4 push-on (screwless) faceplate in a multi-

6 Fit the wires back into the back box. Bend the wires in a zigzag pattern so

that they easily fold into the back box (Figure 2).

Figure 2. Bend the Wires

7 Align the dimmer to the back box (the load rating label should be at the

8 Install the Control4 Faceplate following the instructions in the Faceplate

Installation Guide or attach a standard Decora-style faceplate.

9 Turn ON power at the circuit breaker or replace the fuse

from the fuse box.

Operation and Conﬁguration

On initial power up, all status LEDs on the dimmer will illuminate green indicating that the device has power. To set up this dimmer for use with a Control4 system, refer to the Composer Pro User Guide.

The button tap sequences are deﬁned in the table below. Button tap sequences that require a single (1) button should use the top button.

Function Sequence Button

Identify 4

ZigBee Channel 7

Reboot 15

Factory Reset 9-4-9

Leave Mesh and Reset 13-4-13

Troubleshooting

If the light does not turn on:

• Ensure at least one LED on the face of the dimmer is lit.

• Ensure the light bulb is not burned out and is screwed in tightly.

• Ensure that the circuit breaker is not turned OFF or tripped.

• Check for proper wiring (see “Sample Wiring Conﬁgurations”).

• For help on the installation or operation of this product, email or call the

Control4 Technical Support Center. Please provide your exact model number. Contact support@control4.com or see the web site www.control4.com.

Care and Cleaning

• Do NOT paint the dimmer or its wall plate.

• Do NOT use any chemical cleaners to clean the dimmer.

• Clean surface of the dimmer with a soft damp cloth as needed.

Regulatory/Safety Information

To review Regulatory information for your particular Control4 products, see the information located on the Control4 website at: http://www.control4.com/ regulatory/.

Patent Information

Applicable patents are available at http://www.control4.com/legal/patents.

Warranty

For complete warranty information, including details on consumer legal rights as well as warranty exclusions, review the Warranty card or visit www.control4.com/ warranty.

About this Document

Part Number: 200-00312, Rev A 3/03/2013

™

Sample Wiring Conﬁgurations

Figure 3. Single Device Location, With Neutral Connection

Figure 4. Multiple Device Location Using Auxiliary Keypad, With Neutral Connection

Figure 5. Multiple Device Location Using Conﬁgurable Keypad, Neutral Required

the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners Pricing and speciﬁcations are subject to change without notice

Regulatory Compliance & Safety Information for Contol4 Model C4-SW120277 & C4SW240.

Electrical Safety Advisory Sécurité électrique consultatif

Important Safety Information

Informations de sécurité importantes

Read the safety instructions before using this product.

Lisez les consignes de sécurité avant d'utiliser ce produit.

1. Read these instructions.

1. Lisez ces instructions.

2. Keep these instructions.

2. Conservez ces instructions.

3. Heed all warnings.

3. Respectez tous les avertissements.

4. Follow all instructions.

4. Suivez toutes les instructions.

5. Do not use this apparatus near water.

5. Ne pas utiliser cet appareil près de l'eau.

6. Clean only with dry cloth.

6. Nettoyez-le uniquement avec un chiffon sec.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

7. Ne pas bloquer les ouvertures de ventilation. Installer conformément aux instructions du fabricant.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

8. Ne pas installer près de sources de chaleur telles que des ra diateurs, registres de chaleur, poêles, ou autres appareils (incluant les amplificateurs) qui produisent de la chaleur.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

9. Ne pas contourner le dispositif de sécurité de la fiche polarisée ou de mise à la terre. Une fiche polarisée possède deux lames dont une plus large que l'autre. Une fiche de terre a

deux lames et une troisième broche de terre. La lame large ou la troisième broche est fournie pour votre sécurité. Si la fiche fournie ne s'adapte pas à votre prise, consultez un électricien pour le remplacement de la prise obsolète.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

10. Protégez le cordon d'alimentation ne soit piétiné ou pincé, en particulier au niveau des fiches, des prises et au point où il sort de l'appareil.

11. Only use attachments/accessories specified by the manufacturer.

11. Utilisez uniquement des fixations / accessoires spécifiés par le fabricant.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

12. Utilisez uniquement avec le chariot, le socle, le trépied, le support ou la table spécifiés par le fabricant ou vendu avec l'appareil. Lorsque vous utilisez un chariot, soyez prudent lorsque vous déplacez l'ensemble chariot / appareil pour éviter des blessures dues au renversement.

13. Unplug this apparatus during lightning storms or when unused for long period s of time. This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources. The warranty for this equipment does not cover damage caused by electrical surge or lightning transients. To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor.

13. Débranchez cet appareil pendant les orages ou lorsqu'il n'est pas utilisé pendant de longues périodes de temps. Cet équipement utilise la puissance AC qui peuvent être soumis à des surtensions électriques, la foudre généralement transitoires qui sont très destructives envers les équipements terminaux connectés à des sources d'alimentation CA. La garantie de cet appareil ne couvre pas les dommages causés par les surtensions électriques ou transitoires de foudre. Pour réduire le risque de cet équipement devient endommagé, il est suggéré que le client envisager l'installation d'un limiteur de surtension.

14. Refer all servicing to qualified service personnel. Servicing is req uired when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. Confiez toutes les réparations à un personnel qualifié. Une réparation est nécessaire lorsque l'appareil a été endommagé de quelque façon que ce soit le cordon d'alimentation ou la fiche est endommagé, du liquide a été renversé ou si des objets sont tombés dans l'appareil, l'appareil a été exposé à la pluie ou à l'humidité, ne fonctionne pas normalement , ou s'il est tombé.

15. Use the circuit breaker to disconnect the apparatus from the AC mains. The circuit breaker shall remain readily accessible.

15. Utiliser le disjoncteur pour déconnecter l'appareil de l'alimentation secteur. Le di sjoncteur doit rester facilement accessible.

16. To completely disconnect unit power from the AC mains, turn off the circuit breaker. To reconnect power, turn on the circuit breaker following all safety instructions and guidelines.

+ 14 hidden pages

Control4 C4SWTV User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual