Contour Design Unimouse operation manual

Product Manual

Wired

Box Contents

1. Unimouse

2. User Guide

2

1

Unimouse Wired

/1

Unimouse Functions

Auto scroll/Scroll wheel

Left click

Middle click/Double click*

Right click

Base/tilt

Wire

For additional mouse features and specic

Mac settings, please download our driver at
contourdesign.com/support

*see page 4

Back button

Forward button

Thumb rest

Cursor speed adjustment (DPI)

Cursor speed(LED)

Unimouse Wired

/2

Connecting to a Computer

Plug the Unimouse into the computer’s USB port. Allow your computer a few
seconds to automatically install the mouse drivers.

Middle Click to Double Click

Unimouse comes with middle click as the defualt setting. To change the middle
click function to double click, hold down the cursor speed button and the middle
click button at the same time. To switch back, repeat the same command.

Middle click / Double click

Cursor speed (DPI)

Unimouse Wired

/3

Adjustable Features

Unimouse has 4 key points of articulation. We econourage you to explore a
variety of positions while using your Unimouse. For more details regarding
adjustability, please refer to the Adjustability Guide.

The thumb rest can be extended or

collapsed to accomodate dierent

handsizes.

Slide the thumb support forward or
back to accomodate variations in
thumb length and grip preference.

Unimouse Wired

Adjust tilt for your desired mousing
angle.

e

The thumb support can be rotated
in any direction to adjust to your
prefered thumb position.

/4

Change Cursor Speed

Press the cursor speed button to cycle through cursor speeds. There are ten
speed selections ranging from slow (800 DPI) to fast (2800 DPI). Speed is
indicated by the LED lights as shown.

B

6) 1800 7) 2000 8) 2200 9) 2400 10) 2800

1) 800 2) 1000 3) 1200 4) 1400 5) 1600

Unimouse Wired

/5

For more information please visit:
www.contourdesign.com

Contour Design, Inc.
10 Industrial Drive
Windham, New Hampshire 03087, USA

Phone: [phone]

Email: [e-mail]

Contour Design Nordic A/S

Borupvang 5B, St.
DK-2750 Ballerup/Denmark
Phone: [phone]

Email: [e-mail]

Tested to comply with FCC
and IC standards

FCC Statement

Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IC Statement

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

The term “IC: “ before the certication/registration number only signies that the Industry Canada technical specications were met. This product
meets the applicable Industry Canada technical specications.

Le présent appareil est conforme aux CNR d’Industrie Canada applicable aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage,

et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le

fonctionnement

Warranty

If there is a functional defect due to faulty manufacturing, we will replace the product. This warranty does not cover damage
that results from misuse of the product.

Attention!

If you attempt to dismantle your Unimouse, you will invalidate your warranty.