Continental Refrigerator DLF27-SS-U-D User Manual

DESIGNER LINE UNDERCOUNTER FREEZER (0°F)

Project Name:

Model: DLF27-SS-U-D

27” Undercounter Freezer
with Drawers

Stainless steel exterior and interior with stainless steel top.

Designed to maintain NSF-7 temperatures in 100°F ambient.

Model Specied:

Location:

Item No: Quantity:

AIA #: SIS #:

Standard Model Features

REFRIGERATION SYSTEM

Performance-rated refrigeration system
Environmentally-safe R-134a refrigerant
Automatic, hot gas condensate evaporator

Non-corrosive, plasticized n evaporator coil

Easily serviceable back mounted compressor

Options and Accessories

(upcharge and lead times may apply)

Stainless steel back Drawer locks
Solid door in lieu of drawers Special electrical requirements (consult factory)
Glass door in lieu of drawers

Consult factory for other model congurations, options and accessories.

CABINET ARCHITECTURE

2” non-CFC polyurethane foam insulation
Stainless steel roll-out drawers
Magnetic snap-in drawer gaskets
Completely enclosed, vented and removable case back
1 3/8” diameter plate casters (factory installed)

MODEL FEATURES

Electronic controller w/ digital display
2” high, bottom mounted front breather air divider
Automatic electric defrost
Expansion valve system

Toll-Free: 800-523-7138

Phone: [phone]
Fax: [phone]

539 Dunksferry Road
Bensalem, PA 19020

www.continentalrefrigerator.com

APPROVAL:

Model Specications

DIMENSIONAL DATA

Net Capacity (cu. ft.) 7.4 (210 cu l)
Width, Overall (in.) 27 1/2 (699 mm)
Depth, Overall (in.)

(incl. handles & bumpers)

Height, Overall (in.)

(incl. 1 3/8” plate casters)

No. of Drawers (two tier) 2
No. of Drawers (three tier) 3

REFRIGERANT DATA

Condensing Unit Size (H.P.) 1/4
Capacity (BTU/Hr)* 1325

31 9/16 (802 mm)

31 13/16 (808 mm)

Model Plan Views

27 1/2”

(699 mm)

ELECTRICAL DATA

Voltage (int’l) 115/60/1 (n/a)
Fans 1
Total Amps (int’l) 4.8 (n/a)
Defrost Amps (int’l) 5.7 (n/a)
10 ft. Cord/Plug [attached] (int’l) Yes (n/a)

SHIPPING DATA

Weight (lbs.) 165 (75 kg)
Height - Crated (in.) 43 1/4 (1099 mm)
Width - Crated (in.) 35 3/4 (908 mm)
Depth - Crated (in.) 37 1/4 (946 mm)

DRAWER PAN CONFIGURATIONS

Two Tier: (1) 12 x 20 x 6 pan per drawer
Three Tier: (1) 12 x 20 x 4 pan per drawer

* Rating @ -15°F evaporator, 90°F ambient

Figures in parentheses reect metric equivalents rounded to the nearest

whole unit.

Equipped with one NEMA-5-15P Plug

(varies by country)

Toll-Free: 800-523-7138

Phone: [phone]
Fax: [phone]

539 Dunksferry Road
Bensalem, PA 19020

www.continentalrefrigerator.com

Due to our continued efforts in developing innovative
products, specifications subject to change without notice.

FRONT VIEW

31 9/16”

1 1/2”

(38 mm)

SIDE VIEW

NOTE: For proper operation, the area under and in front of the cabinet must not be obstructed in any way.

REFRIGERATION SYSTEM

The self-contained refrigeration system is rear
mounted, concealed behind a removable back
cover. Bottom mounted, low prole air divider al­lows for even air circulation to condensing unit.
A “performance-rated”, air-cooled, hermetically
sealed, expansion valve refrigeration system is in­stalled in model. Plasticized nned coil and air cir­culating fans are contained within an easily acces-

sible rear mounted housing. Unique airow design

allows the cabinet to be enclosed on both sides or

mounted ush against a wall. Refrigeration system,

fully charged with R-134a refrigerant, is designed to
maintain 0°F while operating with an unrestricted air
supply in an ambient temperature of 100°F. All con­densate water is directed to a hot gas condensate
vaporizer located in the compressor compartment,
no plumbing is required. A strict quality assurance
team inspects all materials and components to cer­tify the model conforms to the most exacting stan­dards. Model is performance tested for a minimum
of 16 hours prior to crating.

INSULATION

All cabinet walls, top and bottom have high density,
foamed-in-place, non-CFC polyurethane insulation.

(802 mm)

30”

(762 mm)

29 3/4”

(756 mm)

2 1/16”

(52 mm)

CABINET CONSTRUCTION

Materials are top quality, assembled under rigid
supervision conforming to strict quality assurance
requirements. Case is welded metal construction,
internally supported and braced for rigid unit con­struction. Exterior cabinet back and bottom are
heavy-gauge galvanized steel.

Design eliminates overlapping panels with raw
edges. Interior corners are rounded with 1/4” radi­us. Joints and seams are vapor-tight sealed. Easily
removable anti-sweat door heaters, concealed by
non-metallic, non-conductive, high impact ther­mal breaker strips, eliminates condensation build­up on case front.

DRAWER CONSTRUCTION

Front/backs are constructed of heavy-gauge, pol­ished stainless steel with heavy-duty, safety grip,
chrome-plated handles. Drawer fronts are insu­lated with non-CFC polyurethane foam insulation.
Full extension, lift-out frames are heavy gauge,
welded stainless steel mounted on heavy-duty,
easy glide, self-closing slides. Self-adjusting, full
perimeter, magnateic snap-in gaskets guarantee a
positive seal.

31 13/16”

(808 mm)

®

MADE IN THE U.S.A.

© Copyright 2017. Continental Refrigerator.
A Division of National Refrigeration & Air Conditioning Products, Inc.

DLF27-SS-U-D (1/18/17)