Continental Refrigerator DL60-SS-U-D User Manual
DESIGNER LINE UNDERCOUNTER REFRIGERATOR
Project Name:
Model: DL60-SS-U-D
60” Undercounter Refrigerator
with Drawers
Stainless steel exterior and interior with stainless steel top.
Designed to maintain NSF-7 temperatures in 100°F ambient.
Model Specied:
Location:
Item No: Quantity:
AIA #: SIS #:
Standard Model Features
REFRIGERATION SYSTEM
Performance-rated refrigeration system
Environmentally-safe R-134a refrigerant
Automatic, energy-saving, non-electric
condensate evaporator
Non-corrosive, plasticized n evaporator coil
Easily serviceable back mounted compressor
Options and Accessories
(upcharge and lead times may apply)
Stainless steel back Expansion valve system
Solid doors in lieu of drawers Drawer locks
Automatic electric condensate evaporator
Consult factory for other model congurations, options and accessories.
Special electrical requirements
(consult factory)
CABINET ARCHITECTURE
2” non-CFC polyurethane foam insulation
Stainless steel roll-out drawers
Magnetic snap-in drawer gaskets
Completely enclosed, vented and removable case back
1 3/8” diameter plate casters (factory installed)
MODEL FEATURES
Electronic controller w/ digital display
2” high, bottom mounted front breather air divider
Toll-Free: 800-523-7138
Phone: 215-244-1400
Fax: 215-244-9579
539 Dunksferry Road
Bensalem, PA 19020
www.continentalrefrigerator.com
APPROVAL:
Model Specications
Model Plan Views
DIMENSIONAL DATA
Net Capacity (cu. ft.) 17.0 (481 cu l)
Width, Overall (in.) 60 (1524 mm)
Depth, Overall (in.)
(incl. handles & bumpers)
Height, Overall (in.)
(incl. 1 3/8” plate casters)
31 9/16 (802 mm)
31 13/16 (808 mm)
No. of Drawers (two tier) 4
No. of Drawers (three tier) 6
REFRIGERANT DATA
Condensing Unit Size (H.P.) 1/4
Capacity (BTU/Hr)* 1940
ELECTRICAL DATA
Voltage (int’l) 115/60/1 (220/50/1)
Fans 3
Total Amps (int’l) 6.6 4.4)
10 ft. Cord/Plug [attached] (int’l) Yes (No)
SHIPPING DATA
Weight (lbs.) 284 (129 kg)
Height - Crated (in.) 43 1/4 (1099 mm)
Width - Crated (in.) 68 1/4 (1734 mm)
Depth - Crated (in.) 37 1/4 (946 mm)
FRONT VIEW
1 1/2”
(38 mm)
(1524 mm)
31 9/16”
(802 mm)
30”
(762 mm)
60”
29 3/4”
(756 mm)
31 13/16”
(808 mm)
DRAWER PAN CONFIGURATIONS
Two Tier: (1) 12 x 20 x 6 pan per drawer
Three Tier: (1) 12 x 20 x 4 pan per drawer
* Rating @ +25°F evaporator, 90°F ambient
Figures in parentheses reect metric equivalents rounded to the nearest
whole unit.
Equipped with one NEMA-5-15P Plug
(varies by country)
Toll-Free: 800-523-7138
Phone: 215-244-1400
Fax: 215-244-9579
539 Dunksferry Road
Bensalem, PA 19020
www.continentalrefrigerator.com
Due to our continued efforts in developing innovative
products, specifications subject to change without notice.
2 1/16”
SIDE VIEW
NOTE: For proper operation, the area under and in front of the cabinet must not be obstructed in any way.
REFRIGERATION SYSTEM
The self-contained refrigeration system is rear
mounted, concealed behind a removable back cover.
Bottom mounted, low prole air divider allows for
even air circulation to condensing unit. A “performance-rated”, air-cooled,hermetically sealed, capillary type refrigeration system is installed in model.
Plasticized nned coil and air circulating fans are
contained within an easily accessible rear mounted
housing. Unique airow design allows the cabinet to
be enclosed on both sides or mounted ush against
a wall. Refrigeration system, fully charged with R134a refrigerant, is designed to maintain 38°-41°F
while operating with an unrestricted air supply in an
ambient temperature of 100°F. All condensate water
is directed to a non-electric condensate vaporizer located in the compressor compartment, no plumbing
is required. A strict quality assurance team inspects
all materials and components to certify the model
conforms to the most exacting standards. Model is
performance tested for a minimum of 16 hours prior
to crating.
INSULATION
All cabinet walls, top and bottom have high density,
foamed-in-place, non-CFC polyurethane insulation.
CABINET CONSTRUCTION
Materials are top quality, assembled under rigid
supervision conforming to strict quality assurance
requirements. Case is welded metal construction,
internally supported and braced for rigid unit construction. Exterior cabinet back and bottom are
heavy-gauge galvanized steel.
Design eliminates overlapping panels with raw
edges. Interior corners are rounded with 1/4” radius. Joints and seams are vapor-tight sealed. Easily
removable anti-sweat door heaters, concealed by
non-metallic, non-conductive, high impact thermal breaker strips, eliminates condensation buildup on case front.
DRAWER CONSTRUCTION
Front/backs are constructed of heavy-gauge, polished stainless steel with heavy-duty, safety grip,
chrome-plated handles. Drawer fronts are insulated with non-CFC polyurethane foam insulation.
Full extension, lift-out frames are heavy gauge,
welded stainless steel mounted on heavy-duty,
easy glide, self-closing slides. Self-adjusting, full
perimeter, magnateic snap-in gaskets guarantee a
positive seal.
(52 mm)
®
MADE IN THE U.S.A.
© Copyright 2017. Continental Refrigerator.
A Division of National Refrigeration & Air Conditioning Products, Inc.
DL60-SS-U-D (1/18/17)
Loading...