DESIGNER LINE ROLL-IN FREEZER
Project Name:
Model: DL1FI-E
1-Section Extra-High Roll-In
Freezer with 72” Cart Capacity
Standard - Stainless steel front, aluminum end panels and interior
Suffix SA- Stainless steel exterior, aluminum interior
Suffix SS - Stainless steel exterior and interior
Options and Accessories
(upcharge and lead times may apply)
Stainless steel case back Roll-Thru
Epoxy-coated steel shelves Hinged glass door
Chrome or stainless steel shelves Increased refrigeration systems
Rehinging of door (consult factory) Special electrical req. (consult factory)
Expansion valve system
Dial thermometer • One way security screws
Remote models • Locking hasp (lock not included)
Custom laminates • Stainless steel mesh cover
Half doors • Coverless hinges
Consult factory for other model configurations, options and accessories.
Correctional Facility Options
Toll-Free: 800-523-7138
Phone: 215-244-1400
Fax: 215-244-9579
539 Dunksferry Road
Bensalem, PA 19020
www.continentalrefrigerator.com
Model Specified:
Location:
Item No: Quantity:
AIA #: SIS #:
Standard Model Features
REFRIGERATION SYSTEM
Environmentally-safe R-404A refrigerant
Self contained, performance-rated
“plug” refrigeration system
Automatic hot gas condensate evaporator
Unique air flow distribution ducts evenly distributes
air to all pan levels
Refrigeration system is accessible on top of cabinet,
separate from the food zone
CABINET ARCHITECTURE
Removable stainless steel rack guide
Removable stainless steel ramp
Reinforced stainless steel floor
3” non-CFC polyurethane foam insulation
Chrome-plated flow line handle
Cam action, lift off hinges
Magnetic snap-in door gasket
Cylinder lock in door
Self-closing door
72 1/2” high door openings (72”H rack capacity*)
Standard Finish
Stainless steel front, aluminum end panels and interior
-SA Finish
Stainless steel exterior, aluminum interior
-SS Finish
Stainless steel exterior and interior
MODEL FEATURES
External digital thermometer
Energy saving switch for door heater
Automatic electric defrost
* Rack not supplied
IMPORTANT NOTE: Cabinet upper side panels and refrigeration “plug”
system can be easily removed and reinstalled at installation site where
space limitations are confining.
APPROVAL:
Model Specifications
DIMENSIONAL DATA
Net Capacity (cu. ft.) 34 (963 cu l)
Width, Overall (in.) 35 1/4 (895 mm)
Depth, Overall (incl. handles) (in.) 35 3/8 (899 mm)
Depth [less door] (in.) 32 (813 mm)
Depth [door open 90°] (in.) 65 (1651 mm)
Clear Door Width (in.) 27 3/8 (695 mm)
Clear Full Door Height (in.) 72 1/2 (1842 mm)
Height, Overall (in.) 92 (2337 mm)
No. of Door(s) 1
Rack Capacity** 1 ea.
REFRIGERANT DATA
Condensing Unit Size (H.P.) 3/4
Capacity (BTU/Hr)* 3530
ELECTRICAL DATA
Voltage (int’l)
Feed Wires (incl. ground) 4
Total Amps (int’l) 11.1 (10.2)
Defrost Amps (int’l) 9.6 (4.8)
10 ft. Cord/Plug [attached] (int’l) No (No)
SHIPPING DATA
Height - Crated (in.) 97 (2464 mm)
Width - Crated (in.) 43 (1092 mm)
Depth - Crated (in.) 42 (1067 mm)
Volume - Crated (cu. ft.) 98 (2489 cu l)
Weight Std - Crated (lbs.) 475 (215 kg)
Weight SS - Crated (lbs.) 580 (263 kg)
Weight Std - Uncrated (lbs.) 380 (172 kg)
Weight SS - Uncrated (lbs.) 460 (209 kg)
* Rating @ -15°F evaporator, 90°F ambient
** Maximum rack size including wheels - 27”W x 29”D x 72”H
Figures in parentheses reflect metric equivalents rounded to the nearest
whole millimeter.
Due to our continued efforts in developing innovative
products, specifications subject to change without notice.
®
© Copyright 2013. Continental Refrigerator.
A Division of National Refrigeration & Air Conditioning Products, Inc.
115/208-230/60/1
(220/50/1)
Toll-Free: 800-523-7138
Phone: 215-244-1400
Fax: 215-244-9579
539 Dunksferry Road
Bensalem, PA 19020
www.continentalrefrigerator.com
MADE IN THE U.S.A.
Model Plan Views
35 1/4”
(895 mm)
15 1/2”
(394 mm)
92”
(2184 mm)
76 1/2”
(1781 mm)
FRONT VIEW
(899 mm)
SIDE VIEW
IMPORTANT NOTE: If the cabinet is located directly against a wall and/or under a low ceiling, a minimum
clearance of 12” is required.
REFRIGERATION SYSTEM
A “performance rated”, air-cooled, hermetically
sealed, capillary-type refrigeration system is installed on the top of each freezer. Plasticized fin
coil and air circulation fans are contained within a
concealed “plug”-type insulated housing, readily
accessible on top of the cabinet and separate from
the food zone to increase food storage capacity.
The entire “plug” system is fully charged with environmentally safe R-404A refrigerant and mounted
on a sturdy steel, rail-type base which can be easily removed if refrigerator conversion is desired.
Freezers are designed to maintain 0°F (-18° Centigrade) while operating with an unrestricted air supply in a maximum ambient temperature of 100°F.
Automatic electric defrost timer initiates defrost
cycles at predetermined intervals. All condensate
water is evaporated by an automatic, non-electric,
corrosion-resistant condensate evaporator. A strict
quality-assurance team inspects all materials and
components to certify that each model conforms
to the most exacting standards. All models are
factory performance- tested for a minimum of 16
hours prior to crating.
INSULATION
All cabinet walls, top and bottom have high density,
foamed-in-place, non-CFC polyurethane insulation.
CABINET CONSTRUCTION
All materials are of top quality, assembled to conform with strict quality-assurance requirements.
The cabinet front is constructed of heavy-gauge
polished stainless steel for durability. All cabinet
joints and seams are sealed vapor-tight. Case is of
6”
(152 mm)
32”
(813 mm)
all metal, welded construction and internally supported and braced for a rigid unit construction.
Cabinet design eliminated overlapping panels with
raw edges. Cabinet body is insulated with nonCFC, foamed-in-place polyurethane foam with an
average thickness of 3 inches to ensure increased
energy efficiency. Full-length louvered air grille
located above the doors allows equal air circulation to the condensing unit. Easily removable, lowwattage, anti-sweat door heaters concealed by a
non-metallic, non-conductive, high-impact thermal
breaker strip eliminate condensate build-up on the
cabinet front. Automatic interior lighting is controlled by door openings. Cabinets are equipped
with an easily removable, stainless steel ramp and
interior rack guides.
DOOR CONSTRUCTION
Solid hinged door shells are constructed of heavygauge stainless steel and are internally braced and
urethane-foam-insulated for rigidity. Door corners
are welded construction and polished. Replaceable
snap-in door gaskets are self-adjusting, heavyduty, magnetic type. Door handles and hinges are
chrome-plated and non-corrosive. Doors are provided with built-in cylinder locks which are keyed
alike. Hinges are cam action, lift-off type featuring
positive safety stop at 120 degrees.
DL1FI-E (8/14/13)