Continental Refrigerator DL1FI User Manual

DESIGNER LINE ROLL-IN FREEZER

Project Name:

Model: DL1FI

1-Section Roll-In Freezer with 66¼” Cart Capacity

Standard - Stainless steel front, aluminum end panels and interior Suffix SA- Stainless steel exterior, aluminum interior Suffix SS - Stainless steel exterior and interior

Options and Accessories

(upcharge and lead times may apply)

Stainless steel case back Roll-Thru Epoxy-coated steel shelves Hinged glass door Chrome or stainless steel shelves Increased refrigeration systems Rehinging of door (consult factory) Special electrical req. (consult factory) Expansion valve system Dial thermometer • One way security screws Remote models • Locking hasp (lock not included) Custom laminates • Stainless steel mesh cover Half doors • Coverless hinges

Consult factory for other model configurations, options and accessories.

Correctional Facility Options

Toll-Free: 800-523-7138

Phone: 215-244-1400 Fax: 215-244-9579

539 Dunksferry Road Bensalem, PA 19020

www.continentalrefrigerator.com

Model Specified:

Location:

Item No: Quantity:

AIA #: SIS #:

Standard Model Features

REFRIGERATION SYSTEM

Environmentally-safe R-404A refrigerant Self contained, performance-rated

“plug” refrigeration system Automatic hot gas condensate evaporator Unique air flow distribution ducts evenly distributes

air to all pan levels Refrigeration system is accessible on top of cabinet,

separate from the food zone

CABINET ARCHITECTURE

Removable stainless steel rack guides Removable stainless steel ramp Reinforced stainless steel floor 3” non-CFC polyurethane foam insulation Chrome-plated flow line handle Cam action, lift off hinges Magnetic snap-in door gasket Cylinder lock in door Self-closing door 66 1/2” high door opening (66 1/4”H rack capacity*)

Standard Finish

Stainless steel front, aluminum end panels and interior

-SA Finish

Stainless steel exterior, aluminum interior

-SS Finish

Stainless steel exterior and interior

MODEL FEATURES

External digital thermometer Energy saving switch for door heater Automatic electric defrost

* Rack not supplied

IMPORTANT NOTE: Cabinet upper side panels and refrigeration “plug” system can be easily removed and reinstalled at installation site where space limitations are confining.

APPROVAL:

Model Specifications

35 3/8”

DIMENSIONAL DATA

Net Capacity (cu. ft.) 32 (906 cu l) Width, Overall (in.) 35 1/4 (895 mm) Depth, Overall (incl. handles) (in.) 35 3/8 (899 mm) Depth [less door] (in.) 32 (813 mm) Depth [door open 90°] (in.) 65 (1651 mm) Clear Door Width (in.) 27 3/8 (695 mm) Clear Full Door Height (in.) 66 1/2 (1676 mm) Height, Overall (in.) 86 (2184 mm) No. of Door(s) 1 Rack Capacity** 1 ea.

REFRIGERANT DATA

Condensing Unit Size (H.P.) 3/4 Capacity (BTU/Hr)* 3530

ELECTRICAL DATA

Voltage (int’l)

Feed Wires (incl. ground) 4 Total Amps (int’l) 11.1 (10.2) Defrost Amps (int’l) 9.6 (4.8) 10 ft. Cord/Plug [attached] (int’l) No (No)

SHIPPING DATA

Height - Crated (in.) 90 (2286 mm) Width - Crated (in.) 43 (1092 mm) Depth - Crated (in.) 42 (1067 mm) Volume - Crated (cu. ft.) 94 (2661 cu l) Weight Std - Crated (lbs.) 475 (215 kg) Weight SS - Crated (lbs.) 580 (263 kg) Weight Std - Uncrated (lbs.) 380 (172 kg) Weight SS - Uncrated (lbs.) 460 (209 kg)

* Rating @ -15°F evaporator, 90°F ambient ** Maximum rack size including wheels - 27”W x 29”D x 66 1/4”H

Figures in parentheses reflect metric equivalents rounded to the nearest whole millimeter.

Due to our continued efforts in developing innovative products, specifications subject to change without notice.

115/208-230/60/1 (220/50/1)

Toll-Free: 800-523-7138

Phone: 215-244-1400 Fax: 215-244-9579

539 Dunksferry Road Bensalem, PA 19020

www.continentalrefrigerator.com

MADE IN THE U.S.A.

Model Plan Views

35 1/4”

(895 mm)

15 1/2”

(394 mm)

86”

(2184 mm)

70 1/2”

(1781 mm)

FRONT VIEW

(899 mm)

SIDE VIEW

IMPORTANT NOTE: If the cabinet is located directly against a wall and/or under a low ceiling, a minimum clearance of 12” is required.

REFRIGERATION SYSTEM

A “performance rated”, air-cooled, hermetically sealed, capillary-type refrigeration system is installed on the top of each freezer. Plasticized fin coil and air circulation fans are contained within a concealed “plug”-type insulated housing, readily accessible on top of the cabinet and separate from the food zone to increase food storage capacity. The entire “plug” system is fully charged with environmentally safe R-404A refrigerant and mounted on a sturdy steel, rail-type base which can be easily removed if refrigerator conversion is desired. Freezers are designed to maintain 0°F (-18° Centigrade) while operating with an unrestricted air supply in a maximum ambient temperature of 100°F. Automatic electric defrost timer initiates defrost cycles at predetermined intervals. All condensate water is evaporated by an automatic, non-electric, corrosion-resistant condensate evaporator. A strict quality-assurance team inspects all materials and components to certify that each model conforms to the most exacting standards. All models are factory performance- tested for a minimum of 16 hours prior to crating.

INSULATION

All cabinet walls, top and bottom have high density, foamed-in-place, non-CFC polyurethane insulation.

CABINET CONSTRUCTION

All materials are of top quality, assembled to conform with strict quality-assurance requirements. The cabinet front is constructed of heavy-gauge polished stainless steel for durability. All cabinet joints and seams are sealed vapor-tight. Case is of

6”

(152 mm)

32”

(813 mm)

all metal, welded construction and internally supported and braced for a rigid unit construction. Cabinet design eliminated overlapping panels with raw edges. Cabinet body is insulated with nonCFC, foamed-in-place polyurethane foam with an average thickness of 3 inches to ensure increased energy efficiency. Full-length louvered air grille located above the doors allows equal air circulation to the condensing unit. Easily removable, lowwattage, anti-sweat door heaters concealed by a non-metallic, non-conductive, high-impact thermal breaker strip eliminate condensate build-up on the cabinet front. Automatic interior lighting is controlled by door openings. Cabinets are equipped with an easily removable, stainless steel ramp and interior rack guides.

DOOR CONSTRUCTION

Solid hinged door shells are constructed of heavygauge stainless steel and are internally braced and urethane-foam-insulated for rigidity. Door corners are welded construction and polished. Replaceable snap-in door gaskets are self-adjusting, heavyduty, magnetic type. Door handles and hinges are chrome-plated and non-corrosive. Doors are provided with built-in cylinder locks which are keyed alike. Hinges are cam action, lift-off type featuring positive safety stop at 120 degrees.

DL1FI (8/14/13)