Continental Fireplaces CEFB24H, CEFB27H, CEFB29H Installation And Operating Instructions Manual

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

EN

OPERATING INSTRUCTIONS

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA C22.2 No-46 / UL 2021

CEFB24H, CEFB27H

& CEFB29H

ELECTRIC FIREPLACE

FR
PG
25

SAFETY INFORMATION

WARNING

!

If the information in these instructions are

not followed exactly, a  re or explosion
may result causing property damage,
personal injury or loss of life.

- Do not store or use gasoline or other  ammable
vapors and liquids in the vicinity of this or any
other appliance.

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone [phone] • Fax [phone] • www.continental replaces.com • ask@continental re.on.ca

$10.00

1.42A

W415-1438 / A / 06.02.17

2

TABLE OF CONTENTS

EN

1.0 INTRODUCTION 3

1.1 DIMENSIONS 4

1.2 LISTING APPROVALS 5

1.3 GENERAL INSTRUCTIONS 5

1.4 RATING PLATE INFORMATION 6

1.5 LABEL LOCATION 6

2.0 LOCATING APPLIANCE 7

2.1 UNPACKING AND TESTING APPLIANCE 7

2.2 GROUNDING APPLIANCE 7

3.0 INSTALLATION 8

3.1 MINIMUM CLEARANCE TO COMBUSTIBLES 8

3.2 MINIMUM MANTEL CLEARANCES 8

3.3 FRAMING 9

3.3.1 APPLIANCE INSTALLATION 10

3.3.2 HARD WIRING INSTALLATION 11

4.0 OPERATING INSTRUCTIONS 13

4.1 OPERATING CONTROL PANEL 13

4.2 OPERATING BY REMOTE CONTROL 14

5.0 FINISHING 15

5.1 GLASS DOOR REMOVAL AND INSTALLATION 15

5.2 LOG, GRATE AND EMBER BED ASSEMBLY REMOVAL 15

5.3 BRICK PANEL INSTALLATION AND REMOVAL (CEFB29H ONLY) 16

6.0 WIRING DIAGRAM 17

7.0 REPLACEMENT PARTS 18

7.1 CEFB24H OVERVIEW 19

7.2 CEFB27H OVERVIEW 20

7.3 CEFB29H OVERVIEW 21

8.0 TROUBLESHOOTING 22

9.0 WARRANTY 23

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

W415-1438 / A / 06.02.17

Batteries must be disposed of according to the local laws and regulations. Some batteries may be
recycled, and may be accepted for disposal at your local recycling center. Check with your
municipality for recycling instructions.

1.0 INTRODUCTION

!

WARNING

3

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF
CONTACTED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate
appliance according to operating instructions could cause  re or injury.

• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before
servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.

• Do not install damaged, incomplete or substitute components.

• Do not burn wood or other materials in this appliance.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier
is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,
install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the
room and away from hot surfaces.

• Clothing or other  ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of traf c and away from furniture and

draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot
surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the  oor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• It is imperative that the control compartments, circulating blower and its passageway in the appliance

and are kept clean. The appliance should be inspected before use and at least annually by a quali ed
service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding
material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and
other  ammable vapors and liquids.

• Under no circumstances should this appliance be modi ed.

• Do not use this appliance if any part has been under water. Immediately call a quali ed service technician

to inspect the appliance and to replace any part of the control system which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the
glass should be done by a licensed or quali ed service person.

• Do not strike or slam shut the appliance glass door.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Servicing should be done only while the appliance is disconnected from the power supply circuit.

• Always unplug appliance when not in use.

• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been

dropped or damaged in any manner. Return appliance to authorized service facility for examination,
electrical or mechanical adjustment, or repair.

• Do not use outdoors.

• Never locate appliance where it may fall into a bathtub or other water container.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord

away from traf c area and where it will not be tripped over.

• Connect to properly grounded outlets only.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an

electric shock or  re, or damage the appliance.

• To prevent a possible  re, do not block air intakes or exhaust in any manner. Do not use on soft
surfaces, like a carpet, where openings may become blocked.

• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or
relocatable power tap (outlet/power strip).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the
appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,
discolouration or damage to decorations, a T.V. or other electronic components.

3.7C

EN

W415-1438 / A / 06.02.17

4

1.1 DIMENSIONS

EN

24"

610mm

533mm

14 5/8"
371mm

21"

CEFB24H ILLUSTRATED

686mm

27"

610mm

15 3/4"

399mm

24"

17 5/8"
448mm

11 5/8"

294mm

12 3/4"
323mm

18 5/8"

473mm

8 5/8"

219mm

17"

432mm

18"

457mm

22 1/8"

25 1/8"

563mm

639mm

CEFB27H ILLUSTRATED

737mm

29"

17 1/4"
437mm

26"

660mm

CEFB29H ILLUSTRATED

20 1/8"
511mm

14 1/4"
361mm

9 1/2"

9 1/2"

241mm

241mm

19 1/2"

495mm

27 1/4"

20 1/8"

691mm

510mm

W415-1438 / A / 06.02.17

A.

B.

C.

D.
E.

This electric appliance meets the construction and safety standards of H.U.D. for application in manufactured
homes when installed according to these instructions.

!

WARNING

1.2 LISTING APPROVALS

This appliance has been tested in accordance with the CSA Standards for xed and location-dedicated electric
room appliances in the United States and Canada. If you need assistance during installation, please contact

your local dealer.

Model Number CEFB24H CEFB27H CEFB29H

NOTE: This appliance must be
electrically wired and grounded in
accordance with local codes or, in the

absence of local codes, with National

Electric Code ANSI/NFPA 70-latest
edition in the United States or the
Canadian Electric Code, CSA C22.1 in
Canada.

Description 24" Electric

Fireplace

Voltage 120V AC / 60Hz 120V AC / 60Hz 120V AC / 60Hz

Watts Max 1500W Max 1500W Max 1500W

Amps 15 AMP

Grounded
Circuit

Appliance Width 24" (610mm) 27" (686mm) 29" (737m)

Appliance Height 17 5/8"

(448mm)

Appliance Depth 8 5/8" (219mm) 9 1/2" (241mm) 9 1/2" (241mm)

Net Weight 31lbs (14kg) 36lbs (16kg) 38lbs (17kg)

Gross Weight 36lbs (16kg) 40.9lbs (18.6kg) 42lbs (19kg)

27" Electric
Fireplace

15 AMP Ground­ed Circuit

18 5/8" (473mm) 20 1/8" (511mm)

29" Electric
Fireplace

15 AMP Ground­ed Circuit

1.3 GENERAL INSTRUCTIONS

5

EN

READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO

FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY

AND/OR PROPERTY DAMAGE.

ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE

IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL
ACCESSORIES LISTED IN THESE INSTRUCTIONS. USE OF OPTIONAL ACCESSORIES NOT

SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR

RESULT IN A SAFETY HAZARD.

DO NOT OPEN. RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE.

DO NOT USE DAMAGED ELECTRICAL CORDS.

SERVICING SHOULD BE DONE ONLY WHILE THE APPLIANCE IS DISCONNECTED FROM THE

POWER SUPPLY CIRCUIT.

TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF

RECEPTACLE AND FULLY INSERT.

Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the

outlet are on.

The appliance may emit a slight, harmless odour when  rst used. This odour is normal and it is caused

by the initial heating of internal appliance elements and will not occur again.

If your appliance does not emit heat, consult the operation section of this manual for further

information.

Use with a CSA- or UL-certi ed surge protector.

Do not route the power cord directly underneath the appliance.

As with most electronic devices, your new electric replace has been designed to operate at temperatures
between 5°C (41°F) and 35° C (95°F). During the colder winter months, allow the replace to reach room
temperature before turning it on.

4.8B

W415-1438 / A / 06.02.17

6

SAMPLE

1.4 RATING PLATE INFORMATION

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARD: CSA 22.2 NO. 46 AND UL 2021 /

EN

HOMOLOGUÉ SELON LES NORMES NATIONALES CANADIENNES ET AMÉRICAINES: CSA 22.2 NO. 46 UL

2021 / CERTIFICADO SEGÚN LA NORMA NACIONAL DE CANADÁ Y EE. UU.: CSA 22.2 Nº 46 Y UL 2021
ELECTRIC FIREPLACE. SUITABLE FOR
BEDROOM AND BED-SITTING ROOM
INSTALLATION. SUITABLE FOR MOBILE
HOME INSTALLATION.
HOMOLOGUÉ POUR INSTALLATION DANS UNE
CHAMBRE À COUCHER,

MASTER CONTRACT: 161746

VOLTAGE: 120 VAC TENSION: 120 VCA VOLTAJE: 120 VAC
FREQUENCY: 60Hz FRÉQUENCE: 60Hz FRECUENCIA: 60Hz
POWER: 1500W PUISSANCE: 1500W POTENCIA: 1500W
DATE CODE: CODE DE DATE: CÓDIGO DE FECHA:

DESIGNED IN NORTH AMERICA DESIÑADO EN NORTE AMERICA
BY WOLF STEEL LTD. POR WOLF STEEL LTD.
MADE IN CHINA

WOLF STEEL LTD.

24 NAPOLEON ROAD,
BARRIE, ON, L4M 0G8 CANADA

FOYER À ÉLECTRIQUE.

MODEL / MODÈLE / MODELO:

FABRIQUÉ EN CHINE HECHO EN CHINA

UNE SALLE DE BAIN ET UN STUDIO. APPROPRIÉ
POUR INSTALLATION DANS UNE MAISON MOBILE.
CHIMENEA ELÉCTRICA. ADECUADA PARA

INSTALAR EN DORMITORIOS Y SALAS DE ESTAR.
ADECUADA PARA INSTALAR EN HOGARES
MÓVILES.

CONTRAT CADRE: 161746 CONTRATO PRINCIPAL: 161746

DÉSIGNÉ AMÉRIQUE DU
NORD PAR WOLF STEEL LTD.

SERIAL NUMBER / NO. DE SÉRIE /
NÚM. DE SERIE

CEFB29H

CEFB

W385-2218

INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to
the model of the appliance.

For rating plate location, see “LABEL LOCATION” section.

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

1.5 LABEL LOCATION

"DO NOT COVER" LABEL

(W385-2210)

"HOT SURFACE" LABEL

(W385-2017)

FRONT

"ATTENTION" LABEL

(W385-2017)

WARNING

LABEL

(W385-2200)

HARD WIRING

LABEL

(W385-2202)

JUNCTION

BOX

SIDE

RATING PLATE

CEFB24H (W385-2001)

CEFB27H (W385-2217)
CEFB29H (W385-2218)

WARNING LABEL

(W385-2211)

W415-1438 / A / 06.02.17

CAUTION LABEL

(W385-2199)

WIRE DIAGRAM LABEL

(W385-2203)

REAR

2.0 LOCATING APPLIANCE

This appliance is for use on 120 volts. The cord has a plug
as shown in (A). An adapter as shown in (C) is available for
connecting three-blade grounding type plugs to two-slot
receptacles. The green grounding plug extending from the
adapter must be connected to a permanent ground such as
a properly grounded outlet box. The adapter should not be
used if a three-slot grounded receptacle is available.

To disconnect appliance, turn controls to off, then remove
plug from outlet.

!

WARNING

DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF

TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS,

CLOTHES AND CURTAINS AT LEAST 36" FROM THE FRONT OF THE APPLIANCE.

NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER

WATER CONTAINER.

WEAR SAFETY GLOVES, SAFETY FOOTWEAR, AND SAFETY GLASSES FOR PROTECTION DUR-

ING INSTALLATION AND MAINTENANCE.

TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE ELECTRIC APPLIANCE

MUST NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED

OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.

DO NOT EXPOSE THE ELECTRIC APPLIANCE TO THE ELEMENTS (SUCH AS RAIN, ETC.)

2.1 UNPACKING AND TESTING APPLIANCE

Carefully remove the appliance from the box and remove the support brackets. Prior to installing the
appliance, remove all packaging material and test to make sure the appliance operates properly by plugging
the power supply cord into a conveniently located 120V,15 Amp minimum grounded outlet.

7

EN

2.2 GROUNDING APPLIANCE

NOTE: Must be connected to a dedicated15 amp circuit. The
use on an extension cord is NOT permitted.

GROUNDING METHODS

METAL SCREW

(A)

COVER OF

GROUNDED

OUTLET BOX

GROUNDING PIN

(C)

GROUNDING

(B)

ADAPTER

MEANS

NOT ALLOWED IN CANADA

96.1

W415-1438 / A / 06.02.17

8

!

WARNING

3.0 INSTALLATION

EN

RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE CORD TO AVOID

TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY. DO NOT RUN

CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS OR THE LIKE. ARRANGE CORD

AWAY FROM TRAFFIC AREAS AND WHERE IT WILL NOT BE TRIPPED OVER.

RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY MANNER. DO NOT

USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.

RISK OF FIRE! DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED OPTIONAL ACCESSORIES.

USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE

WARRANTY AND/OR RESULT IN A SAFETY HAZARD.

IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE.

HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED AS IT MAY CREATE A FIRE

HAZARD.

DO NOT RUN THE POWER CORD HORIZONTALLY, DIRECTLY BELOW THE APPLIANCE.

68.5A

Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high trafc
areas.

NOTE: Follow all National and local electrical codes.

3.1 MINIMUM CLEARANCE TO COMBUSTIBLES

Measurements are taken from the glass front.

Bottom 0" Top 0" to 2" (51mm) mantel

Sides 1/4" (6.3mm) Top 3" (76mm) to ceiling

Back 1/4" (6.3mm) Top 1/4" (6.4mm) to enclosure

NOTE: The control panel is located on the upper right hand side of the appliance. Always ensure that
access to this switch remains accessible.

3.2 MINIMUM MANTEL CLEARANCES

!

WARNING

WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE

HEAT RESISTANT TO PREVENT DISCOLOURATION.

8"8"

3"

76mm

2"

51mm

1"

25mm

TOP OF APPLIANCE

203mm

152mm

6"

102mm

4"

2"

MANTEL

51mm

1/4"

6.3mm

W415-1438 / A / 06.02.17

L

K

J

B

3.3 FRAMING

Prepare rough in framing following the recommended dimensions in Figure 1. For the corner rough in framing,
follow the recommended dimension in Figure 2.

Select a location that is not prone to moisture and is located at least 36" (914mm) away from combustible
materials such as curtain drapes, furniture, bedding, paper etc.

9

EN

Fig. 1

FLOOR

(Or mantel base thickness)

F

(502mm) + F

B

19 3/4"

32 1/2"

(826mm)

32 1/2"

(826mm)

A

CEFB24H CEFB27H CEFB29H

A 9" (229mm) 10" (254mm) 10" (254mm)
B 23" (584mm) 26" (660mm) 28" (711mm)
C 17 1/4"

(438mm) + F

J 41"

(1041mm)

K 29" (736mm) 31 1/2"

L 29" (736mm) 31 1/2"

18 1/4"

(463mm) + F

44" (1118mm) 46" (1168mm)

(800mm)

(800mm)

C

Fig. 2

K

B

J

A. Once the rough opening has been

prepared, and the power has been
routed to the right side of the recess,

B. The electrical connection must be

the appliance may be installed.

made prior to placing the appliance
into position. (See "HARD WIRING
INSTALLATION" section). Have two
people lift the appliance up and insert

into the opening of the wall.

L

W415-1438 / A / 06.02.17

10

MANTEL

TABLETTE

MANTEL

TABLETTE

APPLIANCE

APPAREIL

STEP 2: INSERT

ÉTAPES 2: INSÉREZ

STEP 3: SET APPLIANCE

ÉTAPES 3: RÉGLÉ APPAREIL

DO NOT SLIDE APPLIANCE

NE GLISSEZ PAS L'APPAREIL

!

!

1/4"

!

!

3.3.1 APPLIANCE INSTALLATION

A. With two people, lift the appliance up and insert into the opening, leave a 3/8" (9.5mm) gap between

EN

B. Set the appliance down and into place, see Figure 2.

the appliance and oor base. Do not push or slide the bottom of the appliance on the oor base, see

Figure 1.

Fig. 1

STEP 1: LIFT

ÉTAPES 1: SOULEVER

APPLIANCE

APPAREIL

MANTEL

MANTEL

TABLETTE

STEP 2: INSERT

ÉTAPES 2: INSÉREZ

DO NOT SLIDE APPLIANCE

NE GLISSEZ PAS L'APPAREIL

F

Fig. 2

MANTEL

W415-1438 / A / 06.02.17

GREEN

BLACK

WHITE

WARNING

3.3.2 HARD WIRING INSTALLATION

!

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

HARD WIRING CONNECTION

If it is necessary to hard wire this appliance, a qualied electrician must remove the cord connection, and
wire the appliance directly to the household wiring. The wire and power supply breaker must rated for 120V
minimum 15 Amps.

This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In
the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the
current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

NOTE: There are 3 wires from the replace junction; white (neutral), black (power L1) and green
(ground) that connect to 120V power supply (breaker panel), see below.

11

EN

White, Green and

Black wires:

Connect to 120V

power supply.

WHITE

BLACK

GREEN

W415-1438 / A / 06.02.17

NEGRO

BLANCO

SUMINISTRO

DE

POTENCIA

VERDE

EN

12

A. Remove the securing screw from the electrical cover plate, located on the right hand side of the

replace.

B. Add an electrical box connector and feed the supply wires through the 7/8" (22mm) hole.
C. Separate the black, white and green wires that have the wire nuts on them.
D. Remove the wire nuts and secure the black wire (power L1) to the black (power L1) lead of the

power supply. Connect the white wire from the unit to the white (neutral) wire from the power
supply. Connect the green wire to the ground wire.

E. Resecure the cover plate.

CHIMENEA

EMPALME

NEGRO

(L1)

BLANCO

VERDE

(N)

(G)

TUERCA DEL

CABLE

NOTE: Leave enough wire so that the appliance can be removed from the enclosure without
disconnecting the power supply.

W415-1438 / A / 06.02.17

POWER

Turns the appliance ON/OFF.

FLAME & EMBER LIGHT
CONTROL

HEATER CONTROL

DECORATIVE LIGHT
(CEFB27/29H ONLY)

TIMER

TEMPERATURE
CONTROL

Controls Flame brightness and the Ember Light.

5 Settings

:

Flame & Ember off (FO), Ember on but Flame
off (LL), small Flame & Ember (F1), medium Flame &
Ember (F2), brightest Flame and Ember (F3).

Turns the Heater and Blower ON/OFF.

4 Settings: Heater & Blower off (HO), Blower on (BL), low
heat (H1), high heat (H2).

Controls Decorative Light settings.
4 Settings

: Decorative Light off (do), white colour (d1),
auto-cycle from White / Orange / Blue / Orange-Blue /
White-Orange / White-Blue (d2), lock to desired colour
(d3). It will take 8.5 seconds to switch between colours
(on d2 setting).

Timer can be programed to run appliance for specific
lengths of time (30mins. minimum to 6hrs maximum).

Press and hold the Timer button for 5 seconds. This
will change the button to Temperature Control, or vice
versa. There are 7 temperature settings (61

°F, 64°F, 70°F,

75

°F, 81°F, 85°F and OFF)

F° / C° SWITCH

Hold 5

seconds

To change temperature format, Fahrenheit or Celsius.
Press and hold the Flame button for 5 seconds.

HEATER LOCK

Hold 5

seconds

Heater button can be locked or unlocked by holding the
Heater button for 5 seconds.

Hold 5

seconds

4.0 OPERATING INSTRUCTIONS

Once the appliance has been plugged into a grounded electrical outlet or hard wired to a dedicated 120V
power supply, it is ready to operate.

NOTE: Ensure the house circuit breakers for the power supply are turned on. In the event of a power
failure, the ame generation lights will come back on at the high setting, when the power supply

returns.

4.1 OPERATING CONTROL PANEL

The Control Panel are located on the top front of the appliance.

13

EN

W415-1438 / A / 06.02.17

14

WARNING

4.2 OPERATING BY REMOTE CONTROL

TO AVOID DANGER OF SUFFOCATION KEEP THE PACKAGING BAG AWAY FROM BABIES AND

EN

CHILDREN. DO NOT USE IN CRIBS, BED, CARRIAGES OR PLAY PENS. THIS BAG IS NOT A TOY.

KNOT BEFORE THROWING AWAY.

NOTE: When operating the remote control, it must be directed towards the front center of the appliance.

A. The power button can be used to power up or down the appliance.

Pressing this button activates the power to the appliance.
Pressing the power button again will turn off the appliance. The
ember and log will fade out after 4 seconds.

B. To adjust the ame brightness and ember log light, press the ame

button . There is one ember log light and three ame brightness
levels to cycle through and then an off setting ( LL, F1, F2, F3 and
then F0).F3 is the brightest ame level, LL is the ember log light only.

C. To begin the thermostat function press the thermostat button ,

there are 7 temperature settings (61°F, 64°F, 70°F, 75°F, 81°F 85°F
and off). Press the thermostat button to cycle through the settings.
Once you have selected the desired temperature the heater will
automatically function until that temperature is reached. The default
setting will display Fahrenheit. When the room temperature is 2
degrees lower than the temperature setting, the heater will turn on.

!

D. To activate the heater and blower, press the heater button , the

blower will turn on. Press the heater button again to set desired low

or high heat temperature; press the heater button again to turn off the

heater.

E. The timer controls all operating modes of the appliance. To activate

the timer, press the timer button , the icon will illuminate and the
time will appear on the LED display. To choose the desired time,
continue to press the timer button, there are 8 settings (30mins,1h,
2h, 3h, 4h, 5h, 6h and off). The replace will turn off at the setting time.

F. To activate the decoration light (CEFB27/29H Only), press the light button .There are three settings

to cycle through and then an off setting (d1, d2, d3 and then d0). d1 white colour, d2 colour cycles from
White / Orange / Blue / Orange-Blue / White-Blue. It will take 8.5 seconds to switch from one colour to
the next when in d2 setting, d3 will lock to a desired colour.

G. To turn off the appliance, press the power button once on the remote, or press the power button once

on the control panel on the unit.

NOTE: This hand held remote control must remain within 6 meters or 19 feet of the appliance to be
effective.

* CEFB29H REMOTE ILLUSTRATED

4.3 REMOTE BATTERY INSTALLATION

1. To replace the existing battery, remote the battery
holder.

2. To remove the battery holder, turn remote onto front
side and press the left side lever towards the center
while pulling the battery holder out using the slot
provided.

3. Replace existing battery, type CR 2025, with a
new battery and reinstall the battery holder into the
remote by sliding it into position, as shown.

4. Battery cover is secure onto the remote control
when a "CLICKING" noise is heard.

BATTERY (CR 2025)

BATTERY COVER

REMOTE

(REAR SIDE)

W415-1438 / A / 06.02.17

5.0 FINISHING

!

WARNING

!

WARNING

POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID

RECONSTRUCTION.

HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES.

5.1 GLASS DOOR REMOVAL AND INSTALLATION

FACING AND/OR FINISHING MATERIAL MUST NOT INTERFERE WITH AIR FLOW THROUGH AIR

OPENINGS, LOUVRES OPENINGS, OPERATION OF LOUVRES OR DOORS OR ACCESS FOR

SERVICE. OBSERVE ALL CLEARANCES WHEN APPLYING COMBUSTIBLE MATERIALS.

BEFORE DOOR IS REMOVED TURN THE APPLIANCE OFF AND WAIT UNTIL APPLIANCE IS COOL

TO THE TOUCH. DOORS ARE HEAVY AND FRAGILE SO HANDLE WITH CARE.

A. Remove the 4 screws off the appliance, as shown.
B. Remove the glass front and place on a soft non-abrasive

surface.

C. Reverse these steps to reinstall the glass front.

15

EN

SCREW

5.2 LOG, GRATE AND EMBER BED ASSEMBLY REMOVAL

For Model CEFB24H and CEFB27H:

A. Remove the 4 screws securing the ember bed to the sides (and bottom, if applicable) of the

appliance, as shown.

NOTE: Some models only have two screws.

B. Lift the log, grate and ember bed up from the appliance and remove.

For Model CEFB29H:

A. Remove the packaging materials holding the logs, grate and ember bed assembly to the appliance.
B. Pinch the back of the assembly and lift it up from the appliance.

CEFB27H ILLUSTRATED

SCREW SCREW

SCREW

(if applicable)

SCREW

(if applicable)

W415-1438 / A / 06.02.17