Continental Fireplaces CDVS600-1N, CS600-1N, CDVS600-1P, CS600-1P Installation And Operation Manual

NATURAL GAS MODELS:

CDVS600-1N / CS600-1N

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

ENGLISH

PROPANE GAS MODELS:

SAFETY INFORMATION

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

- Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

CDVS600-1P / CS600-1P

FRENCH

PG. 71

INSTALLATION AND

ADD MANUAL TITLE

OPERATION MANUAL

Product Name / Code

Gas Stoves Series

(MUST use title from Price Book)

SAFETY BARRIER

ADD PRODUCT IMAGE

(CDVS600-1 illustrated)

ADD ____ ILLUSTRATED

- Installation and service must be performed

by a qualiﬁ ed installer, service agency, or the supplier.

This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁ ed kit is used.

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.continentalﬁ replaces.com • ask@continentalﬁ re.com

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

CSA /

INTERTEK

LOGO

SHOWN WITH OPTIONAL

TRIVET

FOR INDOOR USE ONLY

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

IF INSTALLATION + OPERATION, ADD SERIAL

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE

BARCODE LABEL ON THE OWNER’S MANUAL”

$10.00

W415-1330 / B / 12.06.18

safety information

WARNING

• This appliance is hot when operated and can cause severe burns if contacted.

• Any changes or alterations to this appliance or its controls can be dangerous and is prohibited.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating instructions could cause ﬁ re or injury.

• Ensure the glass door is opened or removed when lighting the pilot for the ﬁ rst time and when the gas supply has run out.

• Risk of ﬁ re or asphyxiation, do not operate appliance with ﬁ xed glass removed and never obstruct the front opening of the appliance.

• Do not connect 110 volts to the control valve, with the exception of models; GSST8 and GT8.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves, protective footwear, and safety glasses during installation. Sheet metal edges may be sharp.

• Do not burn wood or other materials in this appliance.

• Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing and operating the appliance.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at test pressures above 1/2 psig. Close the manual shut-off valve before pressure testing gas line at test pressures equal to or less than 1/2 psig (35mb).

• The appliance must not be operated at temperatures below freezing (32°F / 0°C). Allow the appliance to warm to above freezing prior to operation, with the exception of models; GSS36, GSS42; these appliances are suitable for 0°F / -18°C.

• Children and adults should be alerted to hazards of high surface temperature and should stay away to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and draperies.

• Furniture or other objects must be kept a minimum of 4 feet (1.22m) away from the front of the appliance.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.

• Even after the appliance is off, it will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior to operating the appliance.

• It is imperative that the control compartments, burners and circulating blower and its passageway in the appliance and venting system are kept clean. The appliance and its venting system should be inspected before use and at least annually by a qualiﬁ ed service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• If the appliance shuts off, do not re-light until you provide fresh air. If appliance keeps shutting off, have it serviced. Keep burner and control compartment clean.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not allow wind or fans to blow directly into the appliance. Avoid any drafts that alter burner ﬂ ame patterns.

DANGER

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

W415-1330 / B / 12.06.18

safety information

WARNING

• Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this appliance.

• This appliance must not be connected to a chimney ﬂ ue pipe serving a separate solid fuel burning

appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass

should be done by a licensed or qualiﬁ ed service person, if equipped.

• Do not strike or slam shut the appliance glass door, if equipped.

• Only doors / optional fronts certiﬁ ed with the appliance are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Carbon or soot should not occur in a vent free appliance as it can distribute into the living area of your home. If you notice any signs of carbon or soot, immediately turn off your appliance and arrange to have it serviced by a qualiﬁ ed technician before operating it again.

• If equipped, the screen must be in place (closed) when the appliance is in operation.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating to prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of the exhaust escaping through these openings can also cause the surrounding combustible materials to overheat and catch ﬁ re.

• Carbon monoxide poisoning may lead to death; early signs of carbon monoxide poisoning resemble the

ﬂ u, with headache, dizziness and/or nausea. If you have these signs, the appliance may not be working properly. Get fresh air at once! Have appliance serviced. Some people; pregnant women, persons with heart or lung disease, anemia, those under the inﬂ uence of alcohol, those at high altitudes are more affected by carbon monoxide than others. Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.

• As with any combustion appliance, we recommend having your appliance regularly inspected and

serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and your family against Carbon Monoxide (not applicable for outdoor appliances).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to decorations, a TV or other electronic components.

• For appliances equipped with a safety barrier; if the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this appliance.

• Installation and repair should be done by a qualiﬁ ed service person. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean.

• For outdoor products only: this appliance must not be installed indoors or within any structure that

prevents or inhibits the exhaust gases from dissipating in the outside atmosphere.

• If applicable, the millivolt version of this appliance uses and requires a fast acting thermocouple. Replace

only with a fast acting thermocouple supplied by Wolf Steel Ltd.

WARNING:

which are known to the State of California to cause cancer, and chemicals including carbon

Add California Prop 65 warning

monoxide, which are known to the State of California to cause birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

This product can expose you to chemicals including lead and lead compounds,

WARNING

FIRE RISK HAZARD / DELAYED IGNITION

High supply pressure will damage the valve / controls.

Disconnect the appliance main gas valve/control

from the supply piping when pressure testing that

system at pressures in excess of 1/2 psi (3.5 kPa).

Isolate the appliance with it’s shut off valve during

any pressure testing of the supply piping at

pressures equal to or less than 1/2 psi (3.5 kPa).

W415-1330 / B / 12.06.18

table of contents

1.0 general information 5

1.1 rating plate information 7

1.2 dimensions 7

1.3 shipping bracket 8

2.0 direct venting - model CDVS600-1 9

2.1 typical vent installations 10

2.2 special vent installations 12

2.2.1 periscope termination 12

2.2.2 corner termination 12

2.3 vent terminal clearances 13

2.4 venting application ﬂ ow chart 14

2.5 deﬁ nitions 15

2.6 elbow vent length values 15

2.7 top exit horizontal termination 16

2.8 top exit horizontal termination 17

2.9 rear exit horizontal termination 18

2.10 top or rear exit vertical termination 20

3.0 installation preparation - model CDVS600-1 22

3.1 oriﬁ ce replacement 22

3.2 changing a top vent to a rear vent 23

4.0 installation 24

4.1 minimum clearance to combustibles 24

4.1.1 horizontal installation 25

4.1.2 vertical installation 26

4.1.3 horizontal air terminal installation -

model CDVS600-1 27

4.1.4 vertical air terminal installation - model

CDVS600-1 28

4.2 appliance vent connection - model

CDVS600-1 29

4.3 vertical through existing chimney 30

4.4 mobile home installation - model

CDVS600-1 31

4.5 gas installation 31

4.6 optional wall switch 31

4.7 natural vent speciﬁ cs - model CS600-1

4.7.1 chimney installation 32

4.7.2 installing natural vent 33

4.7.3 natural vent 33

4.7.4 combustion air 33

4.7.5 adding vent sections 34

4.7.6 installing ﬂ ashing and storm collar 35

5.0 finishing 36

5.1 front cast removal 36

5.2 safety barrier installation and removal 36

5.3 glass door installation and removal 37

5.4 battery housing installation 38

5.5 glass / door replacement 38

5.6 log placement 39

5.7 logo placement 40

5.8 switch and bracket installation 40

6.0 optional blower installation 41

7.0 wiring diagram 42

8.1 operating instructions 43

8.0 operation 43

8.2 operating instructions - for your safety

read before operating 44

8.3 lighting instructions 44

8.4 anti condensation switch 44

9.1 pilot burner adjustment 45

9.2 venturi adjustment 45

9.0 adjustment 45

9.3 ﬂ ame characteristics 46

9.4 restricting vertical vents - model

CDVS600-1 46

10.0 maintenance 47

10.2 annual maintenance 48

10.1 care of glass 48

11.0 replacement parts 49

12.0 accessories 52

13.0 troubleshooting 53

14.0 warranty 55

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

Batteries must be disposed of according to the local laws and regulations. Some batteries may be recycled, and may be accepted for disposal at your local recycling center. Check with your municipality for recycling instructions.

W415-1330 / B / 12.06.18

Installer, please ﬁ ll out the following information:

Customer: Address: Date of Installation: Location of appliance: Installer: Dealer/Distributor contact number: Serial #:

Model:

standard checklist

Natural Gas: CDVS600-1N CS600-1N

Propane: CDVS600-1P CS600-1P

1.0 general information

When the appliance is installed at elevations above 4,500ft (1371m), and in the absence of speciﬁ c recommendations from the local authority having jurisdiction, the certiﬁ ed high altitude input rating shall be reduced at the rate of 4% for each additional 1,000ft (305m).

Change in ﬂ ame appearance from "HI" to "LO" is more evident in natural gas than in propane.

Expansion / contraction noises during heating up and cooling down cycles are normal and to be expected.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁ ed kit is used.

CDVS600-1 - This appliance is not approved for closet or recessed installations. It is approved for bathroom, bedroom and bedsitting room installations. This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home, where not prohibited by local codes. (Rear vent) Rear exit installations which terminate horizontally and have no vertical vent runs must have the BTU input reduced to 21,000 BTU/hr by changing the oriﬁ ce (supplied).

CS600-1- This appliance is approved for bedroom and bed-sitting room installations.

CDVS600-1 CS600-1

NG P NG P

Altitude (FT) 0-4,500 0-4500 0-4500 0-4500 Max. Input (BTU/

HR) Max. Output (BTU/

HR) Max. Steady State

Efﬁ ciency (w/the fan on)

Max. A.F.U.E. 72% 71% 72% 71%

Min. Inlet Gas Supply Pressure

Max. Inlet Gas Supply Pressure

Manifold Pressure (Under Flow Conditions)

35,000 (Top vent)

21, 000 (Rear vent only)

27,300 24,570 27,300 24,570

78% 78% 78% 78%

4.5" (11mb)

Water Column

7" (17mb)

Water Column

3.5" (9mb)

Water Column

31,500 (Top vent)

21,000 (Rear vent only)

11" (27mb)

Water Column

13" (32mb) W

ater Column

10" (25mb)

Water Column

35, 000 31,500

4.5" (11mb)

Water Column

7" (17mb)

Water Column

3.5" (9mb)

Water Column

11" (27mb)

Water Column

13" (32mb)

Water Column

10" (25mb)

Water Column

W415-1330 / B / 12.06.18

general information

WARNING

• Always light the pilot - whether for the ﬁ rst time or if the gas supply has run out - with the glass door opened or removed.

• Provide adequate clearance for servicing and operating the appliance.

• Provide adequate ventilation.

• Never obstruct the front opening of the appliance.

• Objects placed in front of the appliance must be kept a minimum of 48" (121.9cm) from the front face of the appliance.

• Surfaces around and especially above the appliance can become hot. Avoid contact when the appliance is operating.

• Fire risk. Explosion hazard.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at test pressures above 1/2psig. Close the manual shut-off valve before pressure testing gas line at test pressures equal to or less than 1/2psig (35mb).

• Use only Wolf Steel-approved optional accessories and replacement parts with this appliance. Using non-listed accessories (blowers, doors, louvres, trims, gas components, venting components, etc.) could result in a safety hazard and will void the warranty and certiﬁ cation.

THIS GAS APPLIANCE MUST BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local codes. Installation practices vary from region to region and it is important to know the speciﬁ cs that apply to your area, for example in the state of Massachusetts:

• This product must be installed by a licensed plumber or gas ﬁ tter when installed within the commonwealth of Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of an appliance insert or gas log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂ exible connector must not be longer than 36 inches (0.9m).

• A carbon monoxide detector is required in all rooms containing gas ﬁ red appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed combustion product.

The installation must conform with local codes or, in absence of local codes, the National Gas and Propane Installation Code CSA B149.1 in Canada, or the National Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United States. Suitable for mobile home installation if installed in accordance with the current standard CAN/CSA Z240MH Series, for gas equipped mobile homes, in Canada or ANSI Z223.1 and NFPA 54 in the United States.

The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (35 mb). The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (35 mb). When installed with a blower or fan, the junction box must be electrically connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI / NFPA 70 National Electric Code in the United States. In the case where the blower is equipped with a power cord, it must be connected into a properly grounded receptacle. The grounding prong must not be removed from the cord plug.

The following does not apply to inserts; as long as the required clearance to combustibles is maintained, the most desirable and beneﬁ cial location for an appliance is in the center of a building, thereby allowing the most efﬁ cient use of the heat created. The location of windows, doors and, the trafﬁ c ﬂ ow in the room where the appliance is to be located should be considered. If possible, you should choose a location where the vent will pass through the house without cutting a ﬂ oor or roof joist. If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood ﬂ ooring, the appliance shall be installed on a metal or wood panel extending the full width and depth, unless otherwise tested.

www.ncertied.org

We suggest that our gas hearth products be installed and serviced by professionals who are certied in the U.S. by the National Fireplace

Institute

(NFI) as NFI Gas

Specialists

When the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood ﬂ ooring, the appliance shall be installed on a metal or wood panel extending the full width and depth.

The appliance, when installed with a blower, must be electrically connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI/NFPA 70-1996 National Electrical Code in the United States. The blower power cord must be connected into a properly grounded receptacle. The grounding prong must not be removed from the cord plug.

W415-1330 / B / 12.06.18

1.1 rating plate information

general information

CONFORMS TO / CONFORME AUX: ANSI Z21.50-2016, CERTIFIED TO / CERTIFIE CSA 2.22-2016

VENTED DECORATIVE GAS APPLIANCE / FOYER À GAZ VENTILÉ.

NOT FOR USE WITH SOLID FUEL

9700539 (WSL) 4001658 (NAC)

MODEL NATURAL GAS/GAZ NATURAL MODEL PROPANE/PROPANE MODÈLE

DIRECT VENT B-VENT B-VENT DIRECT VENT

GDS60-1N GS60-1N GS60-1P GDS60-1P CDVS600-1N CS600-1N CS600-1P CDVS600-1P TOP VENT REAR VENT TOP VENT REAR VENT

0-4500 0-4500 0-4500 ALTITUDE(FT/PT)ELEVATION 0-4500 0-4500 0-4500 35,000 *21,000 35,000 INPUT(BTU/H)ALIMENTATION 31,500 31,500 *21,000 21,000 12,000 21,000 REDUCED INPUT(BTU/H)ALIMENTATION REDUITE 22,000 22,000 *13,000 24,500 *14,700 OUTPUT(BTU/H)RENDEMENT 22,050 *14,700

63.1% P4 63.1%

MANIFOLD PRESSURE: 3.5 INCHES W.C. (NG) / 10 INCHES W.C. (LP) PRESSION AU COLLECTEUR: 3.5” (GN) / 10” (PG) D’UNE COLONNE DEAU MIN SUPPLY PRESSURE: 4.5” W.C. (NG) / 11” (LP) PRESSION D’ALIMENTATION MIN: 4.5” (GN) / 11” (PG) D’UNE COLONNE

D’EAU MAX. SUPPLY PRESSURE: 7” W.C. (NG) / 13” W.C. (LP) PRESSION D’ALIMENTATION MAX: 7” (GN) / 13” (PG) D’UNE COLONNE D’EAU FOR USE WITH GLASS DOORS CERTIFIED WITH THIS UNIT ONLY. UTILISER AVEC LES PORTES VITREES HOMOLOGUEES SEULEMENT AVEC CETTE UNITE. WARNING: DO NOT ADD ANY MATERIAL TO THE APPLIANCE, WHICH WILL COME IN CONTACT WITH THE FLAMES, OTHER THAN THAT SUPPLIED BY THE MANUFACTURER WITH THE APPLIANCE. DECORATIVE PRODUCT: NOT FOR USE AS A HEATING APPLIANCE OPTIONALBLOWER KIT / ENSEMBLE DE VENTILATEUR FACULTATIF: GS64-KT

WOLF STEEL LTD.

24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA

4001659 (WUSA) 4001657 (NGZ)

*WHEN VENTING OFF THE REAR OF THE UNIT AND TERMINATING HORIZONTALLY

UN COMBUSTIBLE SOLIDE NE DOIT

PAS ETRE UTILISE AVEC CET APPAREIL

AVERTISSEMENT: N’AJOUTEZ PAS A CET APPAREIL AUCUN MATERIAU DEVANT ENTRER EN CONTACT AVEC LES FLAMMES AUTRE QUE CELUI QUI EST FOURNI AVEC CET APPAREIL PAR LE FABRICANT. PRODUIT DÉCORATIF: NE PAS UTI;ISER COMME APPARIEL DE CHAUFFAGE

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIAL / DEGAGEMENTS MINIMAUX DES MATERIAUX COMBUSTIBLES:

A 6” B 6” C 2” 20” TO CEILING FROM STOVE TOP

1” TO DIRECT VENT AND B-VENT / L’EVACUATION DIRECTE & L’EVACUATION B 6” TO C-VENT/ A L’EVACUATION C 20” ENTRE LE DESSUS DU FOYER ET LE PLAFOND ELECTRICAL RATING/CLASS: 115V 1.5AMP 60HZ

MODEL CDVS600-1/GDS60-1 APPROVED FOR BEDROOM, BATHROOM & BEDSITTING ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCORDANCE WITH THE CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONTRUCTION AND SAFETY STANDARD, TITLE 24 CFR, PART 3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATIONS, SITES AND COMMUNITIES, ANSI/NFPA 501A. FOR

USE WITH BARRIER W010-3296. FOLLOW THE INSTALLATION INSTRUCTIONS LOCATED IN THE INSTALLATION MANUAL.

HOMOLOGUE POUR INSTALLATION DANS UNE CHAMBRE A COUCHER, UNE SALLE DE BAIN ET UN STUDIO. APPROPRIE POUR INSTALLATION DANS UNE MAISON MOBILE SI SON INSTALLATION CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SERIE DE MAISONS MOBILES EQUIPEES AU GAZ, EN VIGUEUR AU CANADA OU AUX ETATS-UNIS DE LA NORME DE SECURITE ET DE CONSTRUCTION DE MAISONS MANUFACTUREES, TITRE 24 CFR, SECTION 3280. DANS LE CAS OU CETTE NORME D’ETATS-UNIS NE PEUT ETRE APPLIQUEE, SE REFERER A LA NORME RELATIVE AU CRITERE DE MESURES DE SECURITE CONTRE L’INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURES, LES SITES ET LES COMMUNAUTES, ANSI/NFPA 501A. POUR UNE

UTILISER AVEC BARRIÈRE W010-3296. SUIVEZ LES INSTRUCTIONS D'INSTALLATION SE TROUVENT DANS LE MANUEL D'INSTALLATION.

MINIMUM AND MAXIMUM HORIZONTAL VENT LENGTHS ARE 25 INCHES AND 20 FEET RESPECTIVELY FOR TOP VENTED UNITS AND 13 INCHES AND 20 FEET RESPECTIVELY FOR REAR VENTED UNITS. LES LONGUEURS HORIZONTALES MINIMALE ET MAXIMALE SONT 25 POUCES ET 20 PIEDS RESPECTIVEMENT POUR UN EVACUATION VERTICALE ET 13 POUCES ET 20 PIEDS RESPECTIVEMENT POUR UN EVACUATION HORIZONTALE. THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE NAPOLEON VENT KITS. SEE OWNERS INSTALLATION MANUAL FOR VENTING SPECIFICS. PROPER REINSTALLATION AND RESEALING IS NECESSARY AFTER SERVICING THE VENT-AIR INTAKE SYSTEM. L’APPAREIL DOIT EVACUER SES GAZ EN UTILISANT L’ENSEMBLE D’EVACUATION PROPRE A NAPOLEON. REFERER AU MANUEL D’INSTALLATION DE PROPRIETAIRE POUR L’EVACUATION PRECISE. IL EST IMPORTANT DE BIEN REINSTALLER ET RESCELLER L’EVENT APRES AVOIR ASSURE LE MAINTIEN DU SYSTEME DE PRISE D’AIR.

MODEL CS600-1/GS60-1

APPROVED FOR BEDROOM, & BEDSITTING ROOM INSTALLATION. HOMOLOGUE POUR INSTALLATION DANS UNE CHAMBRE A COUCHER, & UN STUDIO. THIS APPLIANCE MUST BE INSTALLED USING AN ADAPTER KIT GS-150KT. CET APPAREIL DOIT ETRE INSTALLE EN UTILISANT UN ENSEMBLE ADAPTATEUR GS-150KT.

SERIAL NUMBER

NO. DE SERIE

GDS60

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

W385-1961 / B

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

1.2 dimensions

37"

SAFETY BARRIER

940mm

30 1/2"

775mm

454mm

17 7/8"

495mm

19 1/2"

24"

610mm

27"

686mm

102mm

178mm

DIA.

5 1/2"

140mm

W415-1330 / B / 12.06.18

general information

1.3 shipping bracket

WARNING

• The top casting is not fastened to the stove assembly. It simply sits on the stove as a lid. For shipping purposes, it is held in place by plastic strapping. Once the strapping is cut, the top should be lifted off carefully and stored in a safe place to avoid damage while completing the installation of the stove. To avoid the appliance being damaged during shipping, a shipping bracket has been used and must be unbolted before the appliance can be installed.

SHIPPING BRACKET REMOVAL A. Remove the four screws holding the shipping bracket to the

bottom of the appliance.

B. Lift the appliance off the skid and set on a ﬂ at surface. C. Discard the screws, brackets and skid.

GLASS DOOR REMOVAL A. Lift the top casting off. B. Open the valve control cover. Pull the latch handles forward to

release. The door may now be safely removed by swinging the bottom out and lifting it off.

SHIPPING BRACKET

LATCH

W415-1330 / B / 12.06.18

2.0 direct venting - model CDVS600-1

WARNING

• Risk of ﬁ re. Maintain speciﬁ ed air space clearances to vent pipe and appliance.

• The vent system must be supported every 3’(0.9m) for both vertical and horizontal runs. Use support ring assembly W0100067 or equivalent non-combustible strapping to maintain the minimum clearance to combustibles for both vertical and horizontal runs. Spacers are attached to the inner pipe at predetermined intervals to maintain an even air gap to the outer pipe. This gap is required for safe operation. A spacer is required at the start, middle, and end of each elbow to ensure this gap is maintained. These spaces must not be removed.

This appliance uses a 4” (102mm) exhaust / 7” (178mm) air intake vent pipe system. Refer to the section applicable to your installation.

For safe and proper operation of the appliance, follow the venting instructions exactly. Deviation from the minimum vertical vent length can create difﬁ culty in burner start-up and/or carboning. Under extreme vent conﬁ gurations, allow several minutes (5-15) for the ﬂ ame to stabilize after ignition. Although not a requirement, it is recommended for vent lengths that pass through unheated spaces (attics, garages, crawl spaces) be insulated with the insulation wrapped in a protective sleeve to minimize condensation. Provide a means for visually checking the vent connection to the appliance after the appliance is installed. Use a

ﬁ restop, vent pipe shield or attic insulation shield when penetrating interior walls, ﬂ oor or ceiling.

The vent terminal may be painted with a high temperature paint to match exterior colours. Use an outdoor paint suitable for 400°F (200°C). Application and performance of paint is the consumer’s responsibility. Spot testing is recommended.

note:

If for any reason the vent air intake system is disassembled, re-install per the instructions provided for the initial installation.

This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing alternate constructions such as a chimney as part of the vent system is not permitted.

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting components. Minimum and maximum vent lengths, for both horizontal and vertical installations, clearances from vent pipes to combustibles and air terminal locations as set out in this manual apply to all vent systems and must be adhered to. For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab, follow the installation procedure provided with the venting components or on the website for your venting supplier. A starter adaptor must be used with the following vent systems and may be purchased from the corresponding supplier:

direct venting - model CDVS600-1

Vent Manufacturer

Duravent W175-0053 Wolf Steel www.duravent.com

Amerivent 4DSC-N2 American Metal www.americanmetalproducts.com

Direct Temp 4DT-AAN Selkirk www.selkirkcorp.com

SuperSeal 4DNA Metal-Fab www.mtlfab.com

For vent systems that provide seals on the inner exhaust ﬂ ue, only the outer air intake joints must be sealed using a red high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent pipe joints of all other approved vent systems except for the exhaust vent pipe connection to the appliance ﬂ ue collar which must be sealed using the black high temperature sealant Mill Pac. High temperature sealant must be ordered separately.

When using Wolf Steel venting components, use only approved Wolf Steel rigid / ﬂ exible components with the following termination kits: wall terminal kit GD-222, GD-222R, or 1/12 to 7/12 pitch roof terminal kit GD-110, 8/12 to 12/12 roof terminal

This template must be used in conjunction with templates 7.1.1 or 7.1.2, depending on

kit GD-111, ﬂ at roof terminal kit GD-112 or periscope kit GD-201 (for wall penetration below grade). With ﬂ exible venting, in

termination shape (i.e. round, or round and square). See appropriate templates folder.

conjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD-220 or the 10 foot (3.1m) vent kit GD-330. For stoves only: wall terminal kit GD-175 (venting included).

For optimum ﬂ ame appearance and appliance performance, keep the vent length and number of elbows to a minimum.

The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that it is unobstructed and undamaged.

Rigid and ﬂ exible venting systems must not be combined. Different venting manufacturer components must not be combined.

These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run is 20 feet (6.1m). The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of vent connections is two horizontally or three vertically (excluding the appliance and the air terminal connections) when using ﬂ exible venting.

Starter Adapter Part Number Supplier Website

W415-1330 / B / 12.06.18

direct venting - model CDVS600-1

Horizontal runs may have a 0” rise per foot or 0mm rise per meter however for optimum performance it is recommended that all horizontal runs have a minimum 1/4” rise per foot or 21mm rise per meter using ﬂ exible venting. For safe and proper operation of the appliance, follow the venting instructions exactly.

A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings. Local codes or regulations may require different clearances.

Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼” (31.8mm) air gap all around between the inner liner and outer liner is required for safe operation.

Use a ﬁ restop when penetrating interior walls, ﬂ oor or ceiling.

If approved for use with a power vent kit, state: “This appliance is certiﬁ ed for use with a power vent kit. Contact your local authorized dealer for more information.”

If not, cover with a white box.

clearances.

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp or American Metal Amerivent venting components. Minimum and maximum vent lengths, for both horizontal and vertical installations, and air terminal locations for either systems are set out in this manual and must be adhered to.

2.1 typical vent installations

16" (40.6cm)

min.

W415-1330 / B / 12.06.18

TOP VENT

40 ft. (12m)

max.

34" (864mm) min.

30 1/2"

(77.5cm)

40 ft. (12m)

max.

34" (864mm)

min.

24"

(61cm)

REAR VENT

24" (61cm) max.

24" (61cm)

min. plus rise*

direct venting - model CDVS600-1

34" (86.4cm) max.

29" (73.7cm)

min.

59 1/2"

(151.1cm)

min. plus rise*

24” (610mm) min.

horizontal vent length

* See "venting" section.

regardless of

Max. horizontal run

20 ft. (6m)

max.

12” (305mm)

min. to grade

W415-1330 / B / 12.06.18

direct venting - model CDVS600-1

2.2 special vent installations

2.2.1 periscope termination

Use the periscope kit to locate the air termination above grade. The periscope must be installed so that when ﬁ nal grading is completed, the bottom air slot is located a minimum 12” (305mm) above grade. The maximum allowable vent length (including both rise and run) is 10’ (3m) for a ﬁ replace and 8’ (2m) for a stove. An insulation sleeve is illustrated in the top vent image below, use only when supplied with the appliance. (The insulation sleeve is not required with a stove appliance)

12"

(30.5cm)

min. to grade

24"

(61cm) min.

2.2.2 corner termination

The maximum vent length for a corner installation is 24" (61cm).

24” (610mm)

0” (0mm) RISE

12"

(30.5cm)

min. to grade

29"

(73.7cm) min.

30 1/2"

(77.5cm)

TOP VENTREAR VENT

MAXIMUM

CORNER INSTALLATION

W415-1330 / B / 12.06.18

2.3 vent terminal clearances

direct venting - model CDVS600-1

Covered balcony applications ††*

= 3 feet

MIN

(0.9m)

INSTALLATIONS

CANADA U.S.A.

12” (30.5cm) 12” (30.5cm) Clearance above grade, veranda porch, deck or balcony.

12” (30.5cm)

12” (30.5cm)* 12” (30.5cm)* Clearance to permanently closed windows.

18”

(45.7cm)**

12” (30.5cm)** 12” (30.5cm)** Clearance to unventilated sofﬁ t.

0” (0mm) 0” (0mm) Clearance to an outside corner wall.

0” (0mm)*** 0” (0mm)***

2” (51mm)*** 2” (51mm)*** Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).

3’(0.9m) 3’(0.9m)****

3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.

12” (30.5cm) 9” (229mm) Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.

6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet.

7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.

12” (30.5cm)†† 12” (30.5cm)**** Clearance under a veranda, porch or deck.

9” (229mm) ΔClearance to windows or doors that open.

18”

(45.7cm)**

Vertical clearance to ventilated sofﬁ ts located above the terminal within a horizontal distance of 2’ (0.6m) from the center line of the terminal.

Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).

Clearance to each side of the center line extended above the meter / regulator assembly to a maximum vertical distance of 15’ (4.6m).

note:

Wall terminals are for illustration purposes only. Size and shapes may vary.

= 2 x

MAX

ACTUAL

MAX

IHHW

(4.6m)

16” (40.6cm) 16” (40.6cm) Clearance above the roof.

2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings.

8’ (2.4m) 8’ (2.4m)

3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.

6’ (1.8m) 6’ (1.8m)

12” (30.5cm) 12” (30.5cm) Clearance under a covered balcony

Δ The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.

* Recommended to prevent condensation on windows and thermal breakage

** It is recommended to use a heat shield and to maximize the distance to vinyl clad sofﬁ ts.

*** The periscope requires a minimum 18 inches clearance from an inside corner.

**** This is a recommended distance. For additional requirements, check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the ﬂ oor.

†* Recommended to prevent recirculation of exhaust products. For additional requirements, check local codes.

††* Permitted only if the balcony is fully open on a minimum of one side.

Roof must be non-combustible without openings.

See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an opening between the terminal and the open side of the structure.

note:

Clearances are to be in accordance with local installation codes and the requirements of the gas supplier. In their absence, clearances are to be as listed above and are based on national codes.

W415-1330 / B / 12.06.18

direct venting - model CDVS600-1

2.4 venting application ﬂ ow chart

Top Exit

Horizontal Termination

Vertical rise is equal

to or greater than the

horizontal run

Horizontal run +

vertical rise to

maximum of

40 feet (12.2m)

Horizontal Termination

Vertical rise is equal

to or greater than the horizontal run

Vertical rise is less than horizontal run

Horizontal run +

vertical rise to

maximum of

24.75 feet (7.5m)

4.2 times the vertical rise equal to or

greater than the

horizontal run

REAR EXIT

Vertical rise is less

than horizontal run

Vertical Termination

Vertical rise is equal

to or greater than the

horizontal run

Horizontal run +

vertical rise to

maximum of

40 feet (12.2m)

Vertical Termination

Vertical rise is equal

to or greater than the horizontal run

Vertical rise is less than horizontal run

Horizontal run +

vertical rise to

maximum of

19 (5.8m)

3 times the vertical

rise equal to or

greater than the

horizontal run

Vertical rise is less than horizontal run

Horizontal run +

vertical rise to

maximum of

40 feet (12m)

Horizontal run +

vertical rise to

maximum of

24.75 feet (7.5m).

3.5 times the

vertical rise equal to

or greater than the

horizontal run

Horizontal run +

vertical rise to

maximum of

40 feet (12m)

Horizontal run +

vertical rise to

maximum of

40 feet (12m)

3 times the vertical

rise equal to or

greater than the

horizontal run

W415-1330 / B / 12.06.18

direct venting - model CDVS600-1

2.5 deﬁ nitions

For the following symbols used in the venting calculations and examples are: > - greater than > - equal to or greater than < - less than < - equal to or less than

- total of both horizontal vent lengths (Hr) and offsets (Ho) in feet

HR - combined horizontal vent lengths in feet HO - offset factor: .03 (total degrees of offset - 90°*) in feet HO - offset factor: .03 (total degrees of offset - 135°*) in feet VT - combined vertical vent lengths in feet

2.6 elbow vent length values

Feet Inches Millimeters 1° 0.03 0.5 12.7 15° 0.45 6.0 152.4 30° 0.9 11.0 279.4 45° 1.35 16.0 406.4 90°* 2.7 32.0 812.8

* The ﬁ rst 90° offset has a zero value and is shown in the formula as - 90° * The ﬁ rst 45° and° offset have a zero value and is shown in the formula as -45° and -90° respectively

or -135° when combined (for 45° exit only).

W415-1330 / B / 12.06.18

V V V

direct venting - model CDVS600-1

2.7 top exit horizontal termination

(HT) > (VT)

Simple venting conﬁguration (only one 90° elbow)

See graph to determine the required vertical rise VT for

12.3 (3.8)

(3733.8)

the required horizontal run H

150 (3810) 147

REQUIRED

100 (2540)

8.3 (2.5)

57 (1447.8)

4.8 (1.5)

4.2 (1.3)

29 (737)

1.6 (5)

50 (1270)

(1.5)

(0.6)

(3.1)

12.5 (3.8)

12.5

(3.8)

(4.6)

19.5 (5.9)

20 (6.1)

19.5 (5.9)

VERTICAL RISE IN

INCHES (MILLIMETERS)

FEET (METERS) V

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERES) H

The shaded area within the lines represents acceptable

values for H

and VT

For vent conﬁgurations requiring more than one 90° elbow, the following formulas apply:

Formula 1: H Formula 2: HT + V

Example:

= VT = 6 FT (1.8m)

= 3 FT (0.9m)

= 5 FT (1.5m)

= H

= .03 (two 90° elbows - 90°) = .03 (180° - 90°) = 2.7FT (0.8m)

= H

+ V

Formula 1: H

< 4.2 V

+ H

= 3FT (0.9m) + 5FT (1.5m) = 8 FT (2.4m)

+ H

= 8FT (2.4m) + 2.7FT (0.8m) = 10.7FT (3.3m)

< 24.75 feet (7.5m)

= 10.7FT (3.3m) + 6FT (1.8m) = 16.7FT (5.1m)

< 4.2 V

90°

4.2 VT = 4.2FT (1.3m) x 6FT (1.8m) = 25.2FT (7.7m)

10.7FT (3.3m) < 25.2FT (7.7m)

Formula 2: HT + V

16.7FT (5.1m) < 24.75 (7.5m)

Since both formulas are met, this vent conﬁguration is acceptable.

< 24.75 FT (7.5m)

90°

Example:

= 4 FT (1.2m)

= 1.5 FT (0.5m)

= V

+ V

= 2 FT (0.6m)

= 1 FT (0.3m)

= 1.5 FT (0.5m)

= H

= .03 (four 90° elbows - 90°) = .03 (360° - 90°) = 8.1 FT (2.5m)

= H

+ V

Formula 1: H

4.2 VT = 4.2 FT (1.3m) x 5.5 FT(1.7m) = 23.1 FT (7m)

= 4FT (1.2m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

+ H2 + H

+ H

= 13.6 FT (4.2m) + 5.5 FT (1.7m) = 19.1 FT (5.8m)

+ H4 = 2FT (0.6m) + 1FT (0.3m) + 1FT (0.3m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

= 5.5 FT (1.7m) + 8.1 FT (2.5m) = 13.6 FT (4.2m)

< 4.2 V

90°

13.6 FT (4.2m) < 23.1 FT (7m) Formula 2: HT + V

19.1FT (5.8m) < 24.75 FT (7.5m)

< 24.75 FT (7.5m)

Since both formulas are met, this vent conﬁguration is acceptable.

W415-1330 / B / 12.06.18

2.8 top exit horizontal termination

direct venting - model CDVS600-1

(HT) ≤ (VT)

Simple venting conﬁguration (only one 90° elbow)

See graph to determine the required vertical rise VT for

the required horizontal run HT.

40 (12.2)

39 (11.9)

Required vertical

rise in feet

(meters) V

30 (9.1)

20 (6.1)

10 (3.1)

2.5

(0.8)5(1.5)

(2.3)

Horizontal vent run plus offset in feet (meters) H

The shaded area within the lines represents acceptable

values for H

For vent conﬁgurations requiring more than one 90° elbow, the following formulas apply:

Formula 1: H Formula 2: HT + V

< V

< 40 feet (12.2m)

Example: V

= 3 ft (0.9m)

= 8 ft (2.4m)

= V1 + V2 = 3 ft (0.9m) + 8 ft (2.4m) = 11 ft (3.4m)

= 2.5 ft (0.8m)

= 2 ft (0.6m)

= H

+ H

= .03 (two 90° elbows - 90°) = .03 (180° - 90°) = 5.4 ft (1.7m)

= H

+ V

Formula 1: H

= 2.5ft (0.8m) + 2 ft (0.6m) = 4.5 ft (1.4m)

+ H

= 4.5 ft (1.4m) + 5.4 ft (1.6m) = 9.9 ft (3m)

= 9.9 ft (3m) + 11 ft (3.4m) = 20.9 ft (6.4m)

< V

9.9 ft (3m) < 11 ft (3.4m) Formula 2: HT + V

< 40 ft (12.2m)

20.9 ft (6.4m) < 40 ft (12.2m) Since both formulas are met, this vent conﬁguration is acceptable.

7.5

90°

(3.1)

and VT

12.5 (3.8)15(4.6)

90°

17.5 (5.3)20(6.1)

W415-1330 / B / 12.06.18

direct venting - model CDVS600-1

2.9 rear exit horizontal termination

(HT) < (VT)

Simple venting conﬁguration

(only two 90° elbows)

For vent conﬁgurations requiring more than two 90° elbows, the following formulas apply:

Formula 1: H Formula 2: HT + V

< V

< 40 feet (12.2m)

Example: V

= 9 FT (2.7m)

= 6 FT (1.8m)

= V

+ V

= 3 FT (0.9m)

= 2 FT (0.6m)

= 1.5 FT (0.5m)

= H

= .03 (four 90° elbows - 90°) = .03 (360° - 90°) = 8.1 FT (2.5m)

= H

+ V

Formula 1: H

= 9FT (2.7m) + 6FT (1.8m) = 15FT (4.6m)

+ H2 + H

+ H

= 14.6FT (4.5m) + 15FT (4.6m) = 29.6 FT (9m)

= 3FT (0.9m) + 2FT (0.6m) + 1.5FT (0.5m) = 6.5FT (2m)

= 6.5FT (2m) + 8.1FT (2.5m) = 14.6FT (4.5m)

< V

14.6 FT (4.5m) < 15 FT (4.6m) Formula 2: HT + V

< 40 FT (12.2m)

29.6 FT (9m) < 40 FT (12.2m)

Since both formulas are met, this vent conﬁguration is acceptable.

See graph to determine the required vertical rise V

REQUIRED

VERTICAL

RISE IN FEET

(METERS) V

The shaded area within the lines represents acceptable values for H

40 (12.2)

38.3 (11.7)

30 (9.1)

20 (6.1)

10 (3.1)

2 (0.6)

1.6 (0.5)

(0.5)

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

horizontal run H

2.5

(0.8)5 (1.5)

1.6

(0.5)

7.5

(2.3)

and HT

7.5

(2.3)

for the required

12.5

17.5

12.5 (3.8)

(4.6)

(3.8)

(5.3)

17.5 (5.3)

(6.1)

(3.1)

90°

W415-1330 / B / 12.06.18

direct venting - model CDVS600-1

(HT) > (VT)

Simple venting conﬁguration

(only two 90° elbows)

REQUIRED

VERTICAL RISE IN

INCHES (MILLIMETERS)

For vent conﬁgurations requiring more than two 90° elbows, the following formulas apply:

Formula 1: H Formula 2: HT + V

< 3.5V

< 24.75 feet (7.5m)

FEET (METERS)V

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) HT

See graph to determine the required vertical rise V

required horizontal run H

150(3810)

12.3 (3.8)

147 (3733.8

100 (2540)

8.3 (2.5)

5.5 (1.2)

(1676.4)

50 (1270)

4.2 (1.3)

1 (0.3)

(610)

2.5

(0.8)5 (1.5)

(0.8)

3.5

(0.3)

(1.1)

(0.3)

(1.1)

5 (1.5) 7.5

(2.3)

7.5

The shaded area within the lines represents acceptable

values for H

and HT

(3.1)

for the

(4.6)

17.5 (5.3)

19.25

19.25 (5.9)

(5.9)

(6.1)

17.5

(4.6)

(5.3)

12.5

(3.1)

(3.8)

Example: V

= 4 FT (1.2m)

= 1.5 FT (0.5m)

= V

+ V

= 2 FT (0.6m)

= 1 FT (0.3m)

= 1.5 FT (0.5m)

= H1+ H2+H3+H4= 2FT(0.6m) + 1FT(0.3m) + 1FT(0.3m) + 1.5FT(0.5m) = 5.5 FT(1.7m)

= .03 (four 90° elbows + one 45° elbow - 90°)

= 4FT (1.2m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

= .03 (90 + 90 + 90 + 90 + 45 - 90) = 9.45 FT (2.9m)

= H

+ H

+ V

Formula 1: H

3.5VT = 3.5FT (1.1m) x 5.5FT (1.7m) = 19.25FT (5.9m)

= 5.5FT (1.7m) + 9.45FT (2.9m) = 14.95FT (4.6m)

= 14.95FT (4.6m) + 5.5FT (1.7m) = 20.45FT (6.2m)

< 3.5V

14.95 FT (4.6m) < 19.25 FT (5.9m)

Formula 2: HT + V

< 24.75 FT (7.5m)

20.45 FT (6.2m) < 24.75 FT (7.5m)

Since both formulas are met, this vent conﬁguration is acceptable.

90°

W415-1330 / B / 12.06.18

direct venting - model CDVS600-1

2.10 top or rear exit vertical termination

(HT) < (VT)

Simple venting conﬁgurations.

REQUIRED

VERTICAL RISE IN

FEET (METERS)V

See graph to determine the required vertical rise V

40 (12.2)

3 (0.9)

30 (9.1)

20 (6.1)

10 (3.1)

required horizontal run H

5 (1.5) 10

(3.1)

15 (4.6) 20

for the

(6.1)

HORIZONTAL VENT RUN PLUS OFFSET IN FEET

(METERS) H

The shaded area within the lines represents acceptable

values for H

and HT

For vent conﬁgurations requiring one or more 90° elbows (top exit) or one or more 90° elbows (rear exit), the following formulas apply:

Formula 1: H Formula 2: HT + V

< V

< 40 feet (12.2m)

Example: V

= 5 FT (1.5m)

= 6 FT (1.8m)

= 10 FT (3.1m)

= V

+ V2 + V

= 8 FT (2.4m)

= 2.5 FT (0.8m)

= H1+ H2 = 8FT (2.4m) + 2.5FT (0.8m) = 10.5FT (3.2m)

= .03 (four 90° elbows - 90°)

= 5FT (1.5m) + 6FT (1.8m) + 10FT (3.1m) = 21 FT (6.4m)

= .03 (360° - 90°) = 8.1 FT (2.5m)

= H

+ H

+ V

Formula 1: H

= 10.5FT (3.2m) + 8.1FT (2.5m) = 18.6FT (5.7m)

= 18.6FT (5.7m) + 21FT (6.4m) = 39.6FT (12.1m)

< 3.5V

18.6 FT (5.7m) < 21 FT (6.4m) Formula 2: HT + V

< 40 FT (12.2m)

39.6FT (12.1m) < 40 FT (12.2m)

Since both formulas are met, this vent conﬁguration is acceptable.

W415-1330 / B / 12.06.18

direct venting - model CDVS600-1

(HT) > (VT)

Simple venting conﬁgurations. See graph to determine the required vertical rise VT for the

REQUIRED

VERTICAL

RISE IN FEET

(METERS)V

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS)HT

For vent conﬁgurations requiring more than two 90° elbows (top exit) or one 90° elbow (rear exit), the following formulas apply:

Formula 1: HT < 3 V Formula 2: HT + V Example:

= 2 FT (0.6m)

= 1 FT (0.3m)

= 1.5 FT (0.5m)

= V

V H H H H

= .03 (360° - 90°) = 8.1 FT (2.5m)

H H Formula 1: H

+ V2 + V3 = 2FT (0.6m) + 1FT (0.3m) + 1.5FT (0.5m) = 4.5 FT (1.4m)

= 6 FT (1.8m)

= 2 FT (0.6m)

= H

+ H

= .03 (four 90° elbows - 90°)

= H

+ V

+ H

= 16.1FT (4.9m) + 4.5FT (1.4m) = 20.6FT (6.3m)

3.5 V

16.1FT (4.9m) < 13.5 FT (4.1m) Since this formula is not met, this vent conﬁguration is unacceptable. Formula 2: HT + V

16.1FT (4.9m) < 13.5 (4.1m)

Since only formula 2 is met, this vent conﬁguration is unacceptable and a new ﬁreplace location or vent conﬁguration will need to be established to satisfy both formulas.

Example:

= 1.5 FT (0.5m)

= 5 FT (1.5m)

= V

+ V2 = 1.5FT (0.5m)+ 5FT (1.5m) = 6.5 FT (2m)

= 1 FT (0.3m)

= 10.75 FT (3.3m)

= H

H H = .03 (360° + 45° - 90°) = 6.75 FT (2.1m) H H

+ H2 + H3 = 1FT (0.3m) + 1FT (0.3m) + 10.75FT (3.3m) = 12.75FT (3.9m)

= .03 (four 90° elbows + one 45° elbow - 90°)

= H

+ H

+ V

= 19.5FT (5.9m) + 6.5FT (2m) = 26 FT (7.9m)

Formula 1:

< 3 V

3 V

19.5FT (5.9m) = 19.5FT (5.9m)

= 3FT (0.9m) x 6.5FT (2m) = 19.5FT (5.9m)

Formula 2:

HT + V 26 FT (7.9m) < 40 FT (12.2m)

< 40 FT (12.2m)

Since both formulas are met, this vent conﬁguration is acceptable.

< 40 feet (12.2m)

= 6FT (1.8m) + 2FT (0.6m) = 8 FT (2.4m)

= 8FT (2.4m) + 8.1FT (2.5m) = 16.1FT (4.9m)

< 3.5 V

= 3FT (0.9m) x 4.5FT (1.4m) = 13.5 FT (4.1m)

< 40 FT (12.2m)

= 12.75FT (3.9m) + 6.75FT (2.1m) = 19.5 FT (5.9m)

19 (5.8)

3 (0.9)

20 (6.1)

10 (3.1)

required horizontal run H

(1.5)

(3.1)

(4.6)

(6.1)

(7.6)

The shaded area within the lines represents acceptable

values for H

and HT

90°

45°

90°

(9.1)

90°

W415-1330 / B / 12.06.18

3.0 installation preparation - model CDVS600-1

installation preparation - model CDVS600-1

3.1 oriﬁ ce replacement

REAR VENT TERMINATION:

Rear exit installations which terminate horizontally and have no vertical vent runs must have the BTU input reduced to 21,000 BTU/hr by changing the oriﬁ ce (supplied).

In order to access the oriﬁ ce, the log support secured by two screws, must be removed.

Care should be taken not to damage the manifold gas pipe. When removing the oriﬁ ce, using a socket wrench, a back-up wrench must be used on the manifold, located below the housing, to ensure that the aluminum tubing does not twist or kink.

W415-1330 / B / 12.06.18

installation preparation - model CDVS600-1

3.2 changing a top vent to a rear vent

In order to convert the venting conﬁ guration from a top exit to a rear exit, remove components as illustrated. When reinstalling in the alternate position: Check gaskets for tears, replace if necessary to ensure a proper seal.

Outer Top

Top Heat

Shield

7” (178mm)

Collar

7” (178mm)

Gasket

4” (102mm)

Collar

4” (102mm)

Gasket

SAFETY BARRIER

7” (178mm) Cover Plate

7” (178mm) Gasket

4” (102mm) Cover Plate

4” (102mm) Gasket

Optional trivet required when converting to rear exit.

W415-1330 / B / 12.06.18

installation

4.0 installation

WARNING

• Ensure to unpack all loose materials from inside the ﬁ rebox prior to connecting the gas and electrical supply

• If your appliance is supplied with a remote, ensure the remote receiver is in the “OFF” position prior to connecting the gas and electrical supply to the appliance.

• For safe and proper operation of the appliance, follow the venting instructions exactly.

• The appliance exhaust ﬂ ue collar must be sealed using Mill Pac. All exhaust and intake vent pipe joints must be sealed using red RTV high temp silicone sealant (W573-0002) (not supplied) or black high temp Mill Pac (W573-0007) (not supplied).

• If using pipe clamps to connect rigid vent components, a minimum of 3 screws must also be used to ensure the connection cannot slip off.

• Do not clamp the ﬂ exible vent pipe.

• Risk of ﬁ re, explosion, or asphyxiation. Improper support of the entire venting system may allow vent to sag and separate. Use vent run supports and connect vent sections per installation instructions.

• Risk of ﬁ re, do not allow loose materials or insulation to touch the vent pipe. Remove insulation to allow for the installation of the attic shield and to maintain clearances to combustibles.

• Do not ﬁ ll the space between the vent pipe and enclosure with any type of material. Do not pack insulation or combustibles between ceiling ﬁ restops. Always maintain speciﬁ ed clearances around venting and ﬁ restop systems. Install wall shields and ﬁ restops as speciﬁ ed. Failure to keep insulation or other materials away from vent pipe may cause ﬁ re.

For optimum performance, it is recommended that all horizontal runs have a minimum 1/4" (6mm) rise per foot when venting. For safe and proper operation of the appliance, follow the venting instructions exactly.

4.1 minimum clearance to combustibles

CDVS600-1: HORIZONTAL VENT SECTIONS: A minimum clearance of 2" (51mm) at the top and 1" (25mm) at the bottom and sides of

the vent pipe on all horizontal runs is required.

VERTICAL VENT SECTIONS: A minimum of 1" (25mm) all around the vent pipe on all vertical runs to combustibles is required.

CS600-1:

A minimum of 1" (25mm) all around the B vent pipe on both horizontal and vertical runs to combustibles is required.

MAINTAIN THESE MINIMUM CLEARANCES TO COMBUSTIBLES: A. 6" (152mm) B. 6" (152mm) C. 2" (51mm)*

Minimum 20" (508mm) from appliance top to ceiling. 6" (152.4mm) to single wall connector.

*At a distance of 2" (51mm) from the wall, access to the blower switch, on-off switch or the blower power cord may not be practical.

W415-1330 / B / 12.06.18

installation

4.1.1 horizontal installation

WARNING

• The ﬁ restop assembly must be installed with the vent shield to the top.

• Terminals must not be recessed into a wall or siding more than the depth of the return ﬂ ange of the mounting plate.

This application occurs when venting through an exterior wall. Having determined the correct height for the air terminal location, cut and frame a hole in the exterior wall, as illustrated, to accommodate the ﬁ restop assembly. Dry ﬁ t the ﬁ restop assembly before proceeding to ensure the brackets on the rear surface ﬁ t to the inside surface of the horizontal framing.

The length of the vent shield may be cut shorter for combustible walls that are less than 8 1/2” (215.9mm) thick but the vent shield must extend the full depth of the combustible wall.

note:

Do not ﬁ ll the air space between the ﬁ restop spacer and the exterior wall with any type of insulating material (i.e. spray foam).

A. Apply a bead of caulking (not supplied) around the outer edge of

the hole of the ﬁ restop assembly, ﬁ t the ﬁ restop assembly to the hole and secure using 4 screws.

B. Once the vent pipe is installed in its ﬁ nal position, apply red RTV silicone (W573-0002) (not supplied)

between the pipe and the ﬁ restop.

CAULKING

FIRESTOP

SPACER

CAULKING

VENT

SHIELD

FINISHING MATERIAL

note:

The above is for illustration purposes only. Vents do not always pass through center of frame.

ADD

HEIGHT

WIDTH

DETERMINE THE CORRECT HEIGHT

ADD

W415-1330 / B / 12.06.18

installation

4.1.2 vertical installation

This application occurs when venting through a roof. Installation kits for various roof pitches are available from your authorized dealer / distributor. See the “accessories” section to order speciﬁ c kits required.

A. Determine the air terminal location, cut and frame a square opening,

as illustrated, in the ceiling and the roof to provide the minimum 1" (25mm) clearance between the vent pipe and any combustible material. Try to center the vent pipe location midway between two joists to prevent having to cut them. Use a plumb bob to line up the center of the openings. A vent pipe shield will prevent any materials such as insulation, from ﬁ lling up the 1" (25mm) air space around the pipe. Nail headers between the joist for extra support.

B. Apply a bead of caulking (not supplied) to the framework or to the

Wolf Steel vent pipe shield plate or equivalent (in the case of a ﬁ nished ceiling), and secure over the opening in the ceiling. A ﬁ restop must be placed on the bottom of each framed opening in a roof or ceiling that the venting system passes through. Apply a bead of caulking all around and place a ﬁ restop spacer over the vent shield to restrict cold air from being drawn into the room or around the ﬁ replace. Ensure that both spacer and shield maintain the required clearance to combustibles. Once the vent pipe is installed in its ﬁ nal position, apply red RTV silicone (W573-0002) (not supplied) between the pipe and the ﬁ restop assembly.

C. In the attic, slide the vent pipe collar down to cover up the open end

of the shield and tighten. This will prevent any materials, such as insulation, from ﬁ lling up the 1" (25mm) air space around the pipe.

Vent Pipe

Shield

Vent Pipe

Shield

Firestop

underside

of joist

Caulking

Vent Pipe

Collar

W415-1330 / B / 12.06.18

installation

4.1.3 horizontal air terminal installation - model CDVS600-1

WARNING

• Terminals must not be recessed into a wall or siding more than the depth of the return ﬂ ange of the mounting plate.

A. Stretch the inner ﬂ ex pipe to the required length taking

into account the additional length needed for the ﬁ nished wall surface. Apply a heavy bead of the red RTV silicone (W573-0002) (not supplied) to the inner sleeve of the air terminal. Slip the vent pipe a minimum of 2” (50.8mm) over the inner sleeve of the air terminal and secure with a minimum of 3 screws.

B. Using the outer ﬂ ex pipe, slide over the outer combustion

air sleeve of the air terminal and secure with a minimum of 3 screws. Seal using red RTV silicone (W573-0002) (not supplied).

C. Insert the vent pipes through the ﬁ restop maintaining

the required clearance to combustibles. Holding the air terminal (lettering in an upright, readable position), secure to the exterior wall and make weather tight by sealing with caulking (not supplied).

D. If more vent pipe needs to be used to reach the ﬁ replace,

couple them together, as illustrated. The vent system must be supported approximately every 3 feet (0.9m) for both vertical and horizontal runs. Use non-combustible strapping to maintain the minimum clearance to combustibles.

E. Stove Appliances Only: From inside the house, using

Red RTV Silicone (W573-0002) (not supplied), seal between the vent pipe and the ﬁ restop. Then slide the black trim collar over the vent pipe up to the ﬁ restop.

The air terminal mounting plate may be recessed into the exterior wall or siding no greater than the depth of its return ﬂ ange.

ADD FASTENER TYP

Caulking

Inner Flex

Pipe

Outer Flex Pipe

Screws

Inner Coupler

Outer Coupler

Inner Flex Pipe

Outer Flex

Screws

(Supplied)

Red RTV Silicone

Outer Flex

ADD GRAPHIC

Pipe

2" (50.8mm) Overlap

Red RTV Silicone

Pipe

W415-1330 / B / 12.06.18

installation

4.1.4 vertical air terminal installation - model CDVS600-1

WARNING

• Maintain a minimum 2” (51mm) space between the air inlet base and the storm collar.

note:

Fastening hardware provided with appropriate roof terminal and liner kits.

A. Fasten the roof support to the roof using 6 screws. The roof support is

optional. In this case, the venting is to be adequately supported using either an alternate method suitable to the authority having jurisdiction or the optional roof support.

B. Stretch the inner ﬂ ex pipe to the required length. Slip the inner ﬂ ex

pipe a minimum of 2” (51mm) over the inner pipe of the air terminal connector and secure with a minimum of three screws, when 4/7, 5/8 and 3/5 venting is used and a minimum of six screws when using 8/10 or 8/11 venting. Seal using a heavy bead of red RTV silicone sealant (W573-0002) (not supplied).

C. Repeat using the outer ﬂ ex pipe, using a heavy bead of red RTV

silicone sealant (W573-0002) (not supplied) and a minimum of three screws, when 4/7, 5/8 and 3/5 venting is used and a minimum of six screws when using 8/10 or 8/11 venting.

D. Thread the air terminal connector / vent pipe assembly down through

the roof. The air terminal must be positioned vertically and plumb. Attach the air terminal connector to the roof support, ensuring that the top of the air terminal is 16” (40.6cm) above the highest point that it penetrates the roof.

E. Remove nails from the shingles, above and to the sides of the air

terminal connector. Place the ﬂ ashing over the air terminal connector leaving a min. 3/4” (19mm) of the air terminal connector showing above the top of the ﬂ ashing. Slide the ﬂ ashing underneath the sides and upper edge of the shingles. Ensure that the air terminal connector is properly centered within the ﬂ ashing, giving a 3/4” (19mm) margin all around. Fasten to the roof. Do not nail through the lower portion of the ﬂ ashing. Make weather-tight by sealing with caulking. Where possible, cover the sides and top edges of the ﬂ ashing with rooﬁ ng material.

F. Aligning the seams of the terminal and air terminal connector, place the

terminal over the air terminal connector making sure the vent pipe goes into the hole in the terminal. Secure with a minimum of three screws, when 4/7, 5/8 and 3/5 venting is used and a minimum of six screws when using 8/10 or 8/11 venting.

G. Apply a heavy bead of weatherproof caulking 2” (51mm) above the

ﬂ ashing. Install the storm collar around the air terminal and slide down to the caulking. Tighten to ensure that a weather-tight seal between the air terminal and the collar is achieved.

H. If more vent pipe needs to be used to reach the appliance, see “horizontal

air terminal installation” section.

Connector

2” (51mm)

Roof Support

Inner Pipe

Air

Terminal

Red RTV

Silicone

(W572-0002)

Inner Flex Pipe

Outer Flex Pipe

Air Inlet Base

Caulking

Sto r m Collar

Weather Sealant

Flashing

W415-1330 / B / 12.06.18

installation

4.2 appliance vent connection - model CDVS600-1

A. Attach the adjustable pipe to the last section of rigid pipe. Secure with

screws and seal.

B. Install the inner ﬂ ex pipe to the appliance. Secure with a minimum of

three screws and ﬂ at washers when installing 3”/5”, 4”/7” or 5”/8” venting, or six screws and ﬂ at washers when installing 8”/10” or 8”/11” venting. Seal the joint and screw holes using Mill Pac sealant (W573-0007) (not supplied).

C. Run a bead of high temperature red RTV silicone sealant (W573-

0002) (not supplied) around the inside of the air intake collar. Pull the adjustable pipe a minimum 2” (50.8mm) into the air intake collar.

note:

Always ﬁ nish vent system installation with the appliance vent connection. Ensure that the sealant is not visible on the exterior pipes once installation is completed. An optional decorative black band may be available with this appliance. In the event that the venting must be disassembled, care must be taken to reseal the venting.

#8 X 1/2”

Self Drilling

Screws

INSERT

IMAGE HERE

Mill-Pac Sealant

2” (50.8mm) Overlap

W415-1330 / B / 12.06.18

AIR

INTAKE

EXHAUST

FLUE

FLEX

LINER

* 40 FT (12.2m)

MAX.

10 FT (3.1m)

MIN

COAXIAL TO

CO-LINEAR ADAPATOR

APPLIANCE

VENT ADAPTOR

TERMINATION

installation

4.3 vertical through existing chimney

WARNING

• Risk of ﬁ re.

• Co-axial to co-linear venting conﬁ gurations must only be used in a non-combustible chimney or enclosure. Installation in a combustible enclosure could result in a ﬁ re.

This appliance is designed to be attached to a 3” (76.2mm) co-linear aluminum ﬂ ex vent system running the full length of a masonry chimney.

The ﬂ ex liners accommodate any contours of a masonry chimney, however, it is necessary to keep the ﬂ exible liners as straight as possible. The inlet air collar of the termination cap must be connected to the air intake ﬂ ex liner and the exhaust collar must be connected to the exhaust ﬂ exible liner.

Both Simpson Duravent and Selkirk co-linear to co-axial adaptors have been approved on this appliance

note:

A vent adaptor will be required directly off the appliance.

Follow vent manufacturer’s installation instructions.

Different manufacturer’s venting components must not be combined. Once the preferred manufacturer’s appliance adaptor has been attached, the remainder of the system must be that of the same manufacturer.

The only exception to this rule is to use Wolf Steel’s approved 3” (76.2mm) ﬂ ex liner and co-linear termination.

* Measured from appliance ﬂ ue collar to termination ﬂ ue collar

W415-1330 / B / 12.06.18

+ 82 hidden pages

Continental Fireplaces CDVS600-1N, CS600-1N, CDVS600-1P, CS600-1P Installation And Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual