Continental Automotive Systems US RCKFBLE Users Manual

The device under test is manufactured by the grantee (Continental Automotive Systems US Inc.);
and sold as an OEM product. Per 47 CFR 2.909, 2.927, 2.931, 2.1033, etc…, the grantee must
ensure the end-user has all applicable / appropriate operating instructions. When end-user
instructions are required, as in the case of this product, the grantee must notify the OEM to notify the
end-user.

Continental Automotive Systems US Inc. will supply this document to the reseller/distributor
dictating what must be included in the end user’s manual for t he commercial product .

INFORMATION TO BE INCLUDED IN THE END USER’S MANUAL

The following information (in blue) must be included in the end product user’s manual to
ensure continued FCC regulatory compliance. The ID numbers must be included in the
manual if the device label is not readily accessible to the end user. The compliance
paragraphs below must be included in the user's manual.

******************************************************************************

USA FCC and ISED Canada Information

This device complies with Part 15 of the FCC Rules and Industry Canada license exempt RSS
standard(s). Operation is subject to the following two cond itions:

(1) this device may not cause harmful interferenc e, and
(2) this device must accept any interference received, including interference that may cause

undesired operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouil lage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instru c tions, m ay
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Grantee and OEM Integrators

This device is intended for Grantee and OEM integrator use only. Please see the full grant of
equipment document for restrictions.

Label Information to the End User by the OEM Integrators

If the FCC ID of this module is not visible when it is installed in side another device, then th e outside of
the device into which the module is installed must be label wi th:

“Contains FCC ID: M3N-RCKFBLE and IC: 7812A-RCKFBLE”.

Antenna caution

This radio transmitter IC: 7812A-RCKFBLE has been approved by Innovation, Science and
Economic Development Canada to operate one with its integral trace ante nnas. T he use of any other
antenna is strictly prohibited for use with this dev ice.

FCC Radiation Exposure Statement

This equipment complies with FCC and ISED radiation exposure limits set forth for an
uncontrolled environment. This transmitter module must not be co-located or operating in
conjunction with any other antenna or transmitter. Co-location with other transmitter antennas
would require the use of FCC multi-transmitter product procedures.

Cet équipement est conforme aux limites d'exposition aux radiations de la FCC et de l'ISDE
établies pour un environnement non contrôlé. Ce module émetteur ne doit pas être co-localisé
ou fonctionner en conjonction avec une autre antenne ou un autre émetteur. La
co-localisation avec d’autres antennes d’émetteur nécessiterait l’utilisation des procédures
FCC relatives aux produits multi-émetteurs.

IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain chassis
configurations or co-location with another transmitter), then the regulatory authorization may no
longer be considered valid and the certification number could not be used on the final product. In
these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and potentially obtaining a sep arate authorization.