Continental Automotive Systems US RCKF Users Manual

The device under test is manufactured by the grantee (Continental Automotive Systems US Inc.);
and sold as an OEM product. Per 47 CFR 2.909, 2.927, 2.931, 2.1033, etc…, the grantee must
ensure the end-user has all applicable / appropriate operating instructions. When end-user
instructions are required, as in the case of this product, the grantee must notify the OEM to notify the
end-user.

Continental Automotive Systems US Inc. will supply this document to the reseller/distributor
dictating what must be included in the end user’s manual for the co mmercial product.

USA FCC and ISED Can ada Information

This device complies with Part 15 of the FCC Rules and Industry Canada license exempt RSS
standard(s). Operation is subject to the following two conditions:

(1) this devi ce may no t cause harm ful interference , and
(2) this device must accept any interference received, including interference that may cause

undesired operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation es t autorisée aux deux conditions suivantes :

(1) l'appareil n e doi t pas prod uire de b rouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receivi ng antenna.

• Increase the separation between the equip ment and re ceiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an ex perienced radio/TV techni cian for hel p.

Grantee and OEM Integrators

This device is intended for Grantee and OEM integrator use only. Please see the full grant of
equipment document for restrictions.

Label Information to the End User by the OEM Integrators

If the FCC ID of this modu le is no t v isible w hen it is i nstalled inside another de v ice, then the o utside o f
the device into which the module is ins talled mus t be label w i th:

“Contains FCC ID: M3N-RCKF and IC: 7812A-RCKF”.

Antenna caution

This radio transmitter IC: 7812A-RCKF has been approved by Innovation, Science and Economic
Development Canada to operate one with its integral trace antennas. The use of any other antenna
is strictly prohibited for use w ith this devi ce.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This transmitter module must not be co-located or operating in conjunction with any
other antenna or transmitter. Co-location with other transmitter antennas would require the use of
FCC multi-transmitter product procedu res.

IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain chassis
configurations or co-location with another transmitter), then the FCC authorization may no longer be
considered valid and the FCC ID could not be used on the final product. In these circumstances, the
OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and
potentially obtaining a separate FCC auth orization.

Page 2 of 2