Continental LNADVW User Manual

FCC ID: LHJ:LNADVW, IC: 2807E-LNADVW

Feature

Description

Cellular Operating Bands

LTE FDD: 17, 4, 2 and 5 WCDMA: II and V

WiFi Operating Bands and Protocols

2.4 GHz:

- 802.11b

- 802.11g

- 802.11n

5 GHz:

- 802.11a

- 802.11n

Application Interface

USB 4 wire UART 2 wire UART Audio: PCM ACC_POWER_ON pin

Operation Guide for LNADVW Module

1. Product Overview

LNADVW wireless module is a proprietary modem designed and manufactured by Continental Automotive Systems, Inc. The modem will be integrated into Data Connectivity Modules (DCMs) designed and produced by Continental for use by automotive OEMs. DCMs will be installed into vehicles during the OEM’s factory assembly process and will not be accessible without use of special tools. Primary use-cases are data-centric with data and voice connections to Telematics Service Providers (TSP). LNADVW also supports WiFi and will be used provide WiFi Hotspot functionality within the vehicle.

Fig. 1. Top view of LNADVW module. Fig. 2. Bottom view of LNADVW module.

LNADVW Feature Table:

Hardware Reset Pin BOOT_OK status pin MSG indicator pin JTAG Antenna interface (Primary, MIMO)

Data Services

LTE data rates: up to 100MBps DL / 50Mbps UL

WiFi data rates:

- 802.11a up to 54 Mbit/s

- 802.11b up to 11 Mbit/s

- 802.11g up to 54 Mbit/s

- 802.11n up to 150 Mbit/s

2. Regulatory Compliance Notes

FCC:

This device complies with Part 15, Part 22(H), Part 24(E) and Part 27 of the FCC Rules. The FCC ID for this device is LHJ-LNADVW. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Industry of Canada:

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.”

« Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. »

This radio transmitter (2807E-LNADVW) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

FCC ID: LHJ:LNADVW, IC: 2807E-LNADVW

« Le présent émetteur radio (2807E-LNADVW) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.»

3. Device Installation and User Manual

The LNADVW module is a proprietary product designed and manufactured by Continental Automotive Systems, Inc. for integration into telematics control units manufactured by Continental Automotive Systems, Inc. for automotive OEMs.

i. The module is limited to installation ONLY in an integrated device manufactured by

Continental Automotive Systems, Inc.

ii. During manufacturing process of the integrated device, the module is soldered onto the

pcb of the integrated device.

iii. The integrated device must provide RF connectors to external antennas or RF traces to

connect the LNADVW modules to antennas inside the integrated device.

The typical reference design for the trace layout, including pcb stack-up and trace length is as described and shown in a Figure 3 below:

Typical RF trace layout between the LNADVW module and RF Connector:

- Recommended RF Connector Type: Fakra

- Main LTE/WCDMA antenna connector (MIMO1) is X203. o Recommended RF trace length is less than 40 mm.

- Diversity LTE/WCDMA antenna connector (MIMO2) is X202. o Recommended RF trace length is less than 45 mm.

- WiFi antenna connector is X201.

o Recommended RF trace length is less than 50 mm.

+ 4 hidden pages