Page 1
Operation Guide for FANW Module
FANW wireless module is a proprietary modem designed and manufactured by Continental
Automotive Systems, Inc. The modem will be integrated into Data Connectivity Modules
(DCMs) designed and produced by Continental for use by automotive OEMs. DCMs will b
installed into vehicles during the OEM’s factory assembly process and will not be accessible
without use of special tools. Primary use
connections to Telematics Service Providers (TSP). FANW also supports WiFi
used provide WiFi Hotspot functionality within the vehicle.
Fig. 1. Top view of FANW module. Fig. 2. Bottom view of FANW module.
WiFi Operating Bands and Protocols
FCC ID: LHJ:FANW, IC: 2807E-FANW
centric with data and voice
ACC_POWER_ON pin
1.
Product Overview
e
-cases are dataand will be
FANW Feature Table:
Feature
Cellular Operating Bands
Application Interface
Description
LTE FDD: 17, 4, 2 and 5
WCDMA: II and V
2.4 GHz:
- 802.11b
- 802.11g
- 802.11n
5 GHz:
- 802.11a
- 802.11n
USB
4 wire UART
2 wire UART
Audio: PCM
Hardware Reset Pin
Page 2
Regulatory Compliance Notes
This device complies with Part 15, Part 22(H), Part 24(E) and Part 27 of the FCC Rules. The
FCC ID for this device is LHJ
This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
This device complies with Industry Canada’s license
the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
« Le présent appareil est conforme
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage
brouillage est susceptible d'en compromettre le fonctionnement. »
This radio transmitter (2807E
the antenna types listed below with the maximum permissible gain i
not included in this list, having a gain greater than the maximum gain indicated for that type,
are strictly prohibited for use with this device.
JTAG Antenna interface (Primary, MIMO)
LTE data rates: up to 100MBps DL / 50Mbps
802.11a up to 54 Mbit/s
802.11b up to 11 Mbit/s
Mbit/s
802.11n up to 150 Mbit/s
FANW. Operation is subject to the following two conditions:
on is subject to
aux CNR d'Industrie Canada applicables aux appareils
radioélectrique subi, même si le
FANW) has been approved by Industry Canada to operate with
ndicated. Antenna types
Data Services
2.
FCC:
FCC ID: LHJ:FANW, IC: 2807E-FANW
BOOT_OK status pin
MSG indicator pin
UL
WiFi data rates:
-
-
- 802.11g up to 54
-
1.
undesired operation.
Industry of Canada:
operation of the device.”
-
-exempt RSSs. Operati
-
Page 3
« Le présent émetteur radio (2807E
ctionner avec les types d'antenne énumérés ci
maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain
maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
Device Installation and User Manual
The FANW module is a proprietary product designed and manufactured by Continental
Automotive Systems, Inc. for integration into telematics control units manufactured by
Continental Automotive Systems, Inc. for automo
The module is limited to installation ONLY in an integrated device manufactured by
Continental Automotive Systems, Inc.
During manufacturing process of the integrated device, the module is soldered onto the
pcb of the integrated device.
The integrated device must provide RF connectors to external antennas or RF traces to
connect the FANW modules to antennas inside the integrated device.
The typical reference design for the trace layout, including pcb stack
described and shown in a Figure 3 below:
Typical RF trace layout between the FANW module and RF Connector:
Recommended RF Connector Type: Fakra
Main LTE/WCDMA antenna connector (MIMO1) is X203.
Recommended RF trace length is less than 40 mm.
LTE/WCDMA antenna connector (MIMO2) is X202.
Recommended RF trace length is less than 45 mm.
WiFi antenna connector is X201.
Recommended RF trace length is less than 50 mm.
FCC ID: LHJ:FANW, IC: 2807E-FANW
FANW) a été approuvé par Industrie Canada pour
dessous et ayant un gain admissible
»
up and trace length is as
-
fon
-
3.
tive OEMs.
i.
ii.
iii.
-
-
-
o
- Diversity
o
-
o
Page 4
Fig. 3. Typical trace routing recommended for use with the FANW module.
FCC ID: LHJ:FANW, IC: 2807E-FANW
Page 5
PCB design information:
Microstrip on layer 1 with ground on layer 2 / 50 ohm Single Ended Line/ 840
Stripline on layer 2 with ground on layers 1&3 / 50 Ohm Single Ended Line/ 405
Fig. 4. Recommended PCB stack
FCC ID: LHJ:FANW, IC: 2807E-FANW
information for use while integrating FANW module.
- PCB Material: FR 4
-
-
mm W 840 mm
-
mm W
-up
Page 6
Automotive OEM is responsible for ensuring that the end
to remove or install module.
The module is limited to installation in mobile applications, according to Par
No other operation configurations are allowed.
Changes or modifications to this system by other than a facility authorized by
Continental could void authorization to use this equipment.
The module must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co
The integrator is responsible for fulfilling FCC and IC requir
use modular approval, then the TCU shall be clearly labeled with
an external label containing the integrated modem’s FCC ID. For example, the label can
include text “Contains device with FCC I
Antenna requirements for use with FANW module:
The module must be installed to provide a separation distance of at least 20cm from all
located or operating in conjunction with any other antenna
The FANW module is for use with external antennas ONLY.
For all LTE/WCDMA operating bands the maximum antenna gain is 6 dBi including
For WiFi 2.4 GHz operating band the maximum antenna gain is 2 dBi including cable
For WiFi 5 GHz operating band the maximum antenna gain is 6 dBi including cable loss.
The maximum gain of the antenna path (cable loss + antenna gain) shall not exceed the
This radio transmitter (FCC ID: LHJ
and Industry Canada to operate with the antenna types listed below with the maximum
permissible gain indicated. Antenna types not included in this list, having a gain greater than
the maximum gain indicated for that type, are str
« Le présent émetteur radio (ID: LHJ
Industrie Canada pour fonctionner avec les types d'antenne énumérés ci
gain admissible maximal. Les types d'antenn
FCC ID: LHJ:FANW, IC: 2807E-FANW
user has no manual instructions
located or operate in conjunction with any other antenna or
ements for the integrated
FAN
) has been approved by FCC
ictly prohibited for use with this device.
FANW) a été approuvé par
dessous et ayant un
e non inclus dans cette liste, et dont le gain est
iv.
-
v.
vi.
vii.
viii.
transmitter.
ix.
device.
If Continental chooses to re-
4.
·
persons and must not be cotransmitter.
t 2.1091(b).
-
D: LHJ-FANW and IC: 2807E-
W”.
or
·
·
cable loss.
·
loss.
·
·
above mentioned values.
-FANW; IC: 2807E-FANW
-FANW; IC: 2807E-
-
Page 7
supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
Continental must instruct the automotive OEM and provide them to include the follow
information into the car user’s manual (i.e. for the DCM):
users must be provided with transmitter/antenna installation requirements and
operating conditions for satisfying RF exposure compliance:
A separate section should clearly state “FCC RF Exposure requirements:”
Required operating conditions for end users.
The antenna used with this device must be installed to provide a separation distance of at
least 20cm from all persons, and must not
transmitter, except in accordance with FCC multi
The Maximum ERP/EIRP and maximum antenna gain required for compliance with Parts
ing the other party’s responsibility to obtain station licensing.
transmit simultaneously with any other
transmitter product procedures.
l'émetteur.»
5.
1. End-
2.
FCC ID: LHJ:FANW, IC: 2807E-FANW
Instructions to OEMs:
ing
3.
4.
5.
15, 22H, 24E, and 27.
6. Clear instructions describ
-
Loading...