Page 1
Pentium 4 2.8/2.4GHz, Celeron 2.0GHz CPU
with HeatSink-FAN
PCP4-28, PCP4-24, PCP4C-20
User’s Guide
CONTEC CO.,LTD.
Thank you for purchasing the product. The product is a combination of a CPU and a heat sink fan.
Follow the procedure in this manual to install the CPU and heat sink fan.
WA RN IN G
Before starting installation, be sure to turn off the power to prevent electric shocks and burns.
Product configuration
- CPU…1
- Heat Sink fan…1
- User’s Guide (this booklet) …1
Target Model
- SPI-8450-LLVA
- SPI-8451-LLVA
- SPI-8451-LVA
Specification
Item PCP4-28 PCP4-24 PCP4C-20
Model Intel(R) Pentium(R) 4
C
P
External Bus Speed 533MHz 400MHz
U
Built-in L2 Cash 512KB 128KB
Core voltage 1.525V
Package FCPGA2 478Pin
Fan speed 5400rpm (Typ.) / 4860rpm (Min.)
F
Life time 40,000 hours
A
Speed sensor Built in
N
Safety features Reverse-connection protection, Stuck-burn prevention
Rated current 0.48A (Typ.) / 0.52A (Max.)
Operating temperature 0 - 50°C
Storage temperature -30 - 75°C
Operating/ Storage humidity
range
Heat-Sink FAN dimensions
(mm)
Heat-Sink FAN weight About 450g
Processor 2.8GHz
20 - 85%RH (No condensation)
90(D) x 95(W) x 62(H)
1
Intel(R) Pentium(R) 4
Processor 2.4GHz
PCP4-28, PCP4-24, PCP4C-20
Intel(R) Celeron(R) Processor
2.0GHz
Page 2
PCP4-28, PCP4-24, PCP4C-20 Instruction Manual
How to attach
(1) Unlock the CPU socket following one of the procedures described below, depending on its type:
Lever type :
Pull up the lever.
(2) Install the CPU onto the socket.
After the installation, lock the CPU socket following one of the procedures described below,
depending on its type:
Lever type :
Push down the lever.
Screw type :
Turn the screw and align it to the release position.
Screw type :
Turn the screw and align it to the lock position.
Lock position
Release position
(3) Mount the heat sink fan on the CPU. Make sure that the levers on the heat sink fan are positioned
as shown below.
PCP4-28, PCP4-24, PCP4C-20 2
Page 3
PCP4-28, PCP4-24, PCP4C-20 Instruction Manual
(4) Press the four corners of the heat sink fan from above to hook the four ends of the heat sink fan clips
into the retention frame on the CPU board.
(5) Push the right and left levers on the heat sink fan slowly down at the same time to fasten the heat sink
fan.
(6) Connect the fan cable to the fan connector on the CPU board.
3
PCP4-28, PCP4-24, PCP4C-20
Page 4
PCP4-28, PCP4-24, PCP4C-20 Instruction Manual
Copyright
Copyright 2003 CONTEC CO., LTD. ALL RIGHTS RESERVE.
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this
document. The information in this document is subject to change without notice. All relevant issues
have been considered in the preparation of this document. Should you notice an omission or any
questionable item in this document, please feel free to notify CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document nor for results obtained by the user as a result of using this product.
Limited One-Year Warranty
CONTEC Interface boards are warranted by CONTEC to be free from defects in material and
workmanship for up to one year from the date of purchase by the original purchaser .
Replacement or repair will be free of charge only when this device is returned to CONTEC freight
prepaid with the original invoice.
This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and
original boards. The warranty is not applicable if the device has been tampered with or damaged
through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in
which case repairs will be considered beyond the warranty policy. If replacement with a new device is
needed, regular factory prices will be charged, the product will be returned to you COD, and no other
written warranty will apply.
The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor
be liable for any incidental or consequential damages due to such defect or consequences that arise from
inexperienced usage, misuse, or malfunction of this device.
How to Obtain Service
For replacement or repair, return the device fr eight prepaid, with a copy of the original invoice. Please
obtain a Return Merchandise Authorization Number (RMA) from our Sales Administration Department
before returning any product. No product will be accepted without an RMA number.
Liability
The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor
be liable for any incidental or consequential damages due to such defect or consequences that arise from
inexperienced usage, misuse, or malfunction of this device.
Copyright 2005 CONTEC CO., LTD. ALL RIGHTS RESERVED.
CONTEC CO., LTD. Jun 2010 Edition
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Japanese http://www.contec.co.jp/
English http://www.contec.com/ A-46-806 (LYDC022)
Chinese http://www.contec.com.cn/ 06212010_rev3 [09192003]
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
Loading...