2.5 inch Hard Disk Drive
PC-HDD40G User’s Guide
CONTEC CO.,LTD.
Thank you for purchasing the CONTEC PC-HDD40 G. Please use
this product in accordance with the procedures described in this
document.
General Caution
- Do not apply pressing force on the top of cover (See Figure 1. on
page 2).
- Do not cover the breathing hole on the top cover (See Figure 2. on
page 2).
- Do not touch the interface connector pins and the surface of printed
circuit board.
- Hard disk are precision instruments. Be extremely careful in
handling during and after assembly.
- The drive can be easily damaged by shocks or ESD (Electrical
Static Discharge), so any damages applied to the drive after taking
out from shipping package and opening ESD protective bag are
user’s responsibilities.
- Be sure to turn off the power of the unit when plugging in or
unplugging connectors.
- Use the mounting screws (M3x5 with sw, w : for screwing the base)
provided with the product. Longer screws may damage the interior
of the product.
- CONTEC bears absolutely no responsibility for use if modified hard
disk.
- This hard disk drive (HDD) has not guaranteed use by continuation
operation and continuation power for 24 hours. When it is used by
continuation operation and continuation power a life fails extremely.
In the case of a 24-hours operation system, use of our company
silicon disk drive is recommended.
-
The life of a hard disk drive changes with environment or operating
conditions. As a standard, power time (motor-on time) below
333hours/month (below 11 hours/day), disk access time is 20% or less, it
becomes which for 20,000 hours (power time) or five years, or an early
thing.
1
PC-HDD40G
Caution of usage
DO NOT PRESS!
Figure 1. Handling caution of PC-HDD20G
- DO NOT PRESS WHEN YOU TAKE OUT THE DRIVE.
- DO NOT PRESS WHEN YOU CARRY THE DRIVE.
- ATTACH THE DRIVE FREE FROM PRESSING FORCE.
DO NOT COVER THIS HOLE
Figure 2. Breathing hole caution of PC-HD D 2 0G
COVERING THIS HOLE WILL RESULT LOSS OF DATA.
PC-HDD40G User’s Guide
Absolutely No Impact!
Excessive impact (greater than 1000G;1ms or 120G;11ms), if this hard
disk is subjected to, might cause a fatal error that is not recoverable.
When transporting, avoid leaving the disk in the equipment. Instead,
use the box the product came in. An impact of 100G is equivalent to
the impact when dropped from a height of about 1cm.
Unaccommodated host PCs
You can not use this drive when if you use these host PCs.
IPC-PT/M30(PC), IPC-PE/M30(PC), IPC-PS/M30(PC),
IPC-PL/M30(PC), IPC-BX/M20(PC ), IPC -B X/ M10(PC), PC-386(PC),
PC-386(PC)S, PC-486M(PC), IPC-PT/M140(PC), IPC-PS/M140(PC),
IPC-PT/M100(PC), IPC-PS/M100(PC), PC-IDE/FD(98)A,
PC-486M(PC)H, IPC-PT/M340(PC)H, IPC-PT/M500(PC),
IPC-PT/M500S(PC), IPC-PT/M530(PC), IPC-PT/M530S(PC),
IPC-TT/M300(PC), IPC-TT/M310(PC), IPC-TT/M340(PC),
IPC-TT/M340S(PC), IPC-TT/M500(PC), IPC-TT/M5 00 S(PC),
IPC-PT/M140(PC), IPC-PT/M140(PC)H, IPC-BX/M400(PC),
IPC-BX/M400(PC)H, IPC-BX/P400(PC)
PC-HDD40G
2
PC-HDD40G User’s Guide
Product Configuration
- Hard Disk Drive……1
- Screw (M3x5, with sw, w) ……4
- Insulation Film……1
- Jumper……1
Note!
Check the contents to make sure that you have everything listed
above.
If you don’t have all the items, Please contact CONTEC.
External Dimensions
100.2 ±0.25
76.6 ±0.2514.0 ±0.25
8-M3
(Depth 3.5±0.5)
61.72 ±0.25
10.00
3.99 3.00 ±0.25
10.14
69.85 ±0.25
9.5 ±0.25
[mm]
Figure 3. External Dimension
3
PC-HDD40G
Master/Slave Settings
43
41
44
42
CA
3
CA
PC-HDD40G User’s Guide
1
AC
24
DB
Note!
D
Master Setting
(Open : Default Setting)
B
D
Slave Setting
A-B Short
B
Figure 4. Master/Slave Settings External Dimension
Specifications differ slightly depending on the drive manufacturer.
Sometimes two drives from two different manufacturers will not
operate together.
Installation
Screw (with sw,w)
Installation Part
HDD
Figure 5. Installation
Insulation Film
PC-HDD40G
4
PC-HDD40G User’s Guide
Mounting orientation
Item Specification
Format Capacity 40Gbyte
Bus Specification AT Interface conforming ATA/ATAPI-7
Transfer Speed (Max.) 100MB/sec (Ultra DMA 100)
Nominal Supply/Tolerance +5VDC/±5%
Consumed Current
Operating Conditions
Nonoperating Conditions
Weight 95g
Startup(max.) 4.5W(RMS Typ.)
Read / Write / Seek 1.4 / 1.4 / 1.7W(RMS Typ.)
Performance idle average 1.25W(RMS Typ.)
Temperature 5°C to 55°C (Ambient)
Humidity 8% to 90%RH (With no condensation)
Maximum Wet Bulb
Temperature
Maximum Temperature Gradient 20°C/Hour
Altitude -300m to 3048m
Ramdom Vibration (RMS) 0.67G (5 to 500Hz)
Swept sine vibration 1G (0-peak), (5 to 500Hz)
Shock 160G (1ms) / 300G (2ms ) / 15G(11ms)
Temperature -40°C to 65°C
Humidity 5% to 95%RH (With no condensation)
Maximum Wet Bulb Te mperature 40°C(With no condensation)
Maximum Temperature Gradient 20°C/Hour
Altitude -300m to 12192m
Ramdom Vibration (RMS) 3.01G (5 to 500Hz)
Swept sine vibration 5G ( 0-peak), (5 to 500Hz)
Shock 1000G (1ms ) / 120G(11ms)
5°C to 60°C (Surface)
29.4°C(With no condensation)
5
PC-HDD40G
PC-HDD40G User’s Guide
Connector Pin Assignment
Pin Signal I/O Type Pin Signal I/O Type
1 RESET- I TTL 2 GND TTL
3 DD07 I/O 3-state 4 DD08 I/O 3-state
5 DD06 I/O 3-state 6 DD09 I/O 3-state
7 DD05 I/O 3-state 8 DD10 I/O 3-state
9 DD04 I/O 3-state 10 DD11 I/O 3-state
11 DD03 I/O 3-state 12 DD12 I/O 3-state
13 DD02 I/O 3-state 14 DD13 I/O 3-state
15 DD01 I/O 3-state 16 DD14 I/O 3-state
17 DD00 I/O 3-state 18 DD15 I/O 3-state
19 GND 20 KEY
21 DMARQ O O3-state 22 GND
23 DIOW- I TTL 24 GND
25 DIOR- I TTL 26 GND
27 IORDY O 3-state 28 CSEL I TTL
29 DMACK- I TTL 30 GND
31 INTRQ O 3-state 32 (reserved)
33 DA01 I TTL 34 PDIAG- I/O OD
35 DA00 I TTL 36 DA02 I TTL
37 CS0- I TTL 38 CS1- I TTL
39 DASP- I/O OD 40 GND
41 +5V logic 42 +5V motor
43 GND 44 (reserved)
Drive Characteristics (Logical Drive Format)
Description Logical
Number
PC-HDD40G 16 63 16,383 512 78,140,160 40,007,761,920
Head
Logical
Sector
/Track
Logical
Cylinder
Number
Logical
Sector
Size
Number
of
Sectors
Total
logical data
Bytes
PC-HDD40G
6
PC-HDD40G User’s Guide
Copyright
Copyright 2006 CONTEC CO., LTD. ALL RIGHTS RESERVE
No part of this document may be copied or reproduced in any form by
any means without prior written consent of CONTEC CO., LTD.
CONTEC CO., LTD. makes no commitment to update or keep current
the information contained in this document. The information in this
document is subject to change without notice.
All relevant issues have been considered in the preparation of this
document. Should you notice an omission or any questionable item
in this document, please feel free to notify CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no
responsibility for any errors that may appear in this document nor for
results obtained by the user as a result of using this product.
Limited One-Year Warranty
CONTEC Interface boards are warranted by CONTEC to be free from
defects in material and workmanship for up to one year from the date
of purchase by the original purchaser.
Replacement or repair will be free of charge only when this device is
returned to CONTEC freight prepaid with the original invoice.
This warranty is not applicable for scratches or normal wear, but only
for the electronic circuitry and original boards. The warranty is not
applicable if the device has been tampered with or damaged through
abuse, mistreatment, neglect, or unreasonable use, or if the original
invoice is not included, in which case repairs will be considered
beyond the warranty policy. If replacement with a new device is
needed, regular factory prices will be charged, the product will be
returned to you COD, and no other written warranty will apply.
The obligation of the warrantor is solely to repair or replace the
product. In no event will the warrantor be liable for any incidental or
consequential damages due to such defect or consequences that arise
from inexperienced usage, misuse, or malfunction of this device.
How to Obtain Service
For replacement or repair, return the device freight prepaid, with a
copy of the original invoice. Please obtain a Return Merchandise
Authorization Number (RMA) from our Sales Administration
Department before returning any product. No product will be
accepted without an RMA number.
7
PC-HDD40G
PC-HDD40G User’s Guide
Copyright 2006 CONTEC CO., LTD. ALL RIGHTS RESERVED.
CONTEC CO., LTD.
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Japanese http://www.contec.co.jp/
English http://www.contec.com/ A-51-347 (LYGW171)
Chinese http://www.contec.com.cn/ [10172006]
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
Loading...