Contec PC-HDD/LG, PC-HDD20G User Manual

2.5 inch IDE Hard Disk Drive with Legacy-signal
PC-HDD/LG User’s Guide
CONTEC CO.,LTD.
Thank you for purchasing the CONTEC PC-HDD/LG. Please use this product in accordance with the procedures described in this document.
General Caution
- Do not apply pressing force on the top of cover (See Figure 1. on page 2).
- Do not cover the breathing hole on the top cover (See Figure 2. on page 2).
- Do not touch the interface connector pins and the surface of printed circuit board .
- Hard disk are precision instruments. Be extremely careful in handling during and after assembly.
- The drive can be easily damaged by shocks or ESD (Electrical Static Discharge), so any damages applied to the drive after taking out from shipping package and opening ESD protective bag are user’s responsibilities.
- Be sure to turn off the power of the unit whe n plugging in or unplugging connectors.
- Use the mounting screws (M3x5 with sw, w : for screwing the base) provided with the product. Longer screws may damage the interior of the product.
- CONTEC bears absolutely no responsibility for use if modified hard disk.
- This hard disk drive (HDD) has not guaranteed use by continuati on operation and continuation power for 24 hours. When it is used by continuation operation and continuation power a life fails extremely. In the case of a 24-hours operation system, use of our company silicon disk drive (SDD) is recommended.
- The life of a hard disk drive changes with environment or operating conditions. As a standard, power time (motor-on time) below 250hours/month (below 8 hours/day), disk access time is 20% or less, it becomes which for 20,000 hours (power time) or five years, or an early thing.
1
PC-HDD/LG
Caution of usage
DO NOT PRESS!
Figure 1. Handling caution of PC-HDD/LG
- DO NOT PRESS WHEN YOU TAKE OUT THE DRIVE.
- DO NOT PRESS WHEN YOU CARRY THE DRIVE.
- ATTACH THE DRIVE FREE FROM PRESSING FORCE.
DO NOT COVER THIS HOLE
Figure 2. Breathing hole caution of PC-HDD/ L G
COVERING THIS HOLE WILL RESULT LOSS OF DATA.
PC-HDD/LG User’s Guide
Absolutely No Impact!
Excessive impact (greater than 900G;1ms or 120G;11ms), if this hard disk is subjected to, might cause a fatal error that is not recoverable. When transporting, avoid leaving the disk in the equipment. Instead, use the box the product came in. An impact of 100G is equivalent to the impact when dropped from a height of about 1cm.
Unaccommodated host PCs
You can not use this drive when if you use these host PCs. IPC-PT/M30(PC), IPC-PE/M30(PC), IPC-PS/M30(PC),
IPC-PL/M30(PC), IPC-BX/M20(PC ), IPC -B X/ M10(PC), PC-386(PC), PC-386(PC)S, PC-486M(PC), IPC-PT/M140(PC), IPC-PS/M140(PC), IPC-PT/M100(PC), IPC-PS/M100(PC), PC-IDE/FD(98)A, PC-486M(PC)H, IPC-PT/M340(PC)H, IPC-PT/M500S(PC), IPC-PT/M530(PC), IPC-PT/M530S(PC),IPC-TT/M300(PC), IPC-TT/M310(PC), IPC-TT/M340(PC),IPC-TT/M340S(PC), IPC-TT/M500(PC), IPC-TT/M500S(PC),IPC-PT/M140(PC), IPC-BX/M400(PC), IPC-BX/P400(PC)
PC-HDD/LG
2
PC-HDD/LG User’s Guide
Capacity is restricted host PCs
You can use only 8Gbyte when if you use these host PCs. IPC-PT/M140(PC)H*1, IPC-BX/M400(PC)H*1, IPC-PT/M500(PC) *1: BIOS of Ver. 1.21 and up is required. If you need, please
download from http://www.contec.com/.
Product Configuration
- Hard Disk Drive……1
- Screw (M3x5, with sw, w) ……4
- Insulation Film……1
- Jumper……1
Note!
Check the contents to make sure that you have everything listed above. If you don’t have all the items, Please contact CONTEC.
External Dimensions
76.35 ±0.2514.25 ±0.25
100 ±0.4
8-M3
61.72 ±0.25
10.00
3.99±0.25 3±0.25
10.14±0.25
69.35 ±0.25
9.5 ±0.2
[mm]
Figure 3. External Dimension
3
PC-HDD/LG
Master/Slave Settings
43
41
44
42
CA
1
AC
3
24
DB
CA
PC-HDD/LG User’s Guide
Note!
D Master Setting (Open : Default Setting)
B
D
Slave Setting A-B Short
B
Figure 4. Master/Slave Settings External Dimension
Specifications differ slightly depending on the drive manufacturer. Sometimes two drives from two differen t manu facturers will not operate together. PC-HDD/LG (mfd. by Fujitsu,MHT2020AC)
Installation
Screw (with sw,w)
Install ation Par t
HDD
Figure 5. Installation
Insulation Film
PC-HDD/LG
4
PC-HDD/LG User’s Guide
Mounting orientation
The drive will operate in all axes(six directions).
Horizontal Orientation 1 Horizontal Orientation 2
Vertical Orientation 1 Vertical Orientation 2
Vertical Orientation 3 Vertical Orientation 4
The gravity direction
The gravity direction
The gravity direction
5
PC-HDD/LG
Hard W ar e Specifications
Item Specification
Format Capacity 20Gbyte Bus Specification AT Interface conforming ATA/ATAPI-6 Transfer Speed (Max.) 100MB/sec (Ultra DMA 100) Nominal Supply/Tolerance +5VDC/±5% Consumed Current
Operating Conditions
Nonoperating Conditions
Weight 99g
Spin up (motor on) 7.0W(RMS Typ.) Read/Write 2.1W(RMS Typ.) Idle 0.9W(RMS Typ.) Temperature 5°C to 55°C (Ambient)
Humidity 8% to 90%RH (With no condensation) Maximum Wet Bulb Temperature Maximum Temperature Gradient 20°C/Hour Altitude -300m to 3000m Vibration (Swept sine, 1/4 octave per minute) Shock (Half-sine pulse) 225G 0-peak, 2ms Temperature -40°C to 65°C Humidity 5% to 95%RH (With no condensation) Maximum Wet Bulb Te mperature 40°C(With no condensation) Maximum Temperature Gradient 20°C/Hour Altitude -300m to 12000m Vibration (Swept sine, 1/4 octave per minute) Shock 900G 0-peak, 1ms
5°C to 60°C (Surface)
29°C(With no condensation)
1G 0-peak, 5 to 500Hz
5G 0-peak, 5 to 500Hz
120G 0-peak, 11ms
PC-HDD/LG User’s Guide
PC-HDD/LG
6
PC-HDD/LG User’s Guide
Connector Pin Assignment
Pin Signal Function I/O Pin Signal Function I/O
1 RESET- Bus Reset I 2 GND Signal Ground 3 DB7 Data Bus Bit 7 I/O 4 DB8 Data Bus Bit 8 I/O 5 DB6 Data Bus Bit 6 I/O 6 DB9 Data Bus Bit 9 I/O 7 DB5 Data Bus Bit 5 I/O 8 DB10 Data Bus Bit 10 I/O
9 DB4 Data Bus Bit 4 I/O 10 DB11 Data Bus Bit 11 I/O 11 DB3 Data Bus Bit 3 I/O 12 DB12 Data Bus Bit 12 I/O 13 DB2 Data Bus Bit 2 I/O 14 DB13 Data Bus Bit 13 I/O 15 DB1 Data Bus Bit 1 I/O 16 DB14 Data Bus Bit 14 I/O 17 DB0 Data Bus Bit 0 I/O 18 DB15 Data Bus Bit 15 I/O 19 GND Signal Ground I/O 20 KEY Key Pin 21 Open 22 GND Signal Ground 23 IOW- Host I/O Write I 24 GND Signal Ground 25 IOR- Host I/O Read I 26 GND Signal Ground 27 IORDY I/O ch RDY O 28 Reserved 29 Reserved 30 GND Signal Ground 31 INTRQ Interrupt Request O 32 IOCS16- Drive 16 Bit I/O O 33 ADD1 Host Address 1 I 34 PDIAG- Passed Diagnostic I/O 35 ADD0 Host Address 0 I 36 ADD2 Host Address 2 I 37 CSO- Chip Select 0 I 38 CS1- Chip Select 1 I 39 DASP- Active (LED) O 40 GND +5V Return 41 +5V +5VDC 42 +5V +5VDC 43 GND +5V Return 44 Reserved
Drive Characteristics (Logical Drive Format)
Description Logical
Number
PC-HDD/LG 16 63 16,383 512 39,070,080 20,003,880,960
Head
Logical
Sector /Track
Logical Cylinder Number
Logical
Sector
Size
Number
of
Sectors
Total
logical data
Bytes
Copyright
Copyright 2003 CONTEC CO., LTD. ALL RIGHTS RESERVE No part of this document may be copied or reproduced in any form by
any means without prior written consent of CONTEC CO., LTD. CONTEC CO., LTD. makes no commitment to update or keep current
the information contained in this document. The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document. Should you notice an omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may appear in this document nor for results obtained by the user as a result of using this product.
7
PC-HDD/LG
Limited One-Year Warranty
CONTEC Interface boards are warranted by CONTEC to be free from defects in material and workmanship for up to one year from the date of purchase by the original purchaser.
Replacement or repair will be free of charge only when this device is returned to CONTEC freight prepaid with the original invoice.
This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and original boards. The warranty is not applicable if the device has been tampered with or damaged through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in which case repairs will be considered beyond the warranty policy. If replacement with a new device is needed, regular factory prices will be charged, the product will be returned to you COD, and no other written warranty will apply.
The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor be liable for any incidental or consequential damages due to such defect or consequences that arise from inexperienced usage, misuse, or malfunction of this device.
How to Obtain Service
For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please obtain a Return Merchandise Authorization Number (RMA) from our Sales Administration Department before returning any product. No product will be accepted without an RMA number.
PC-HDD/LG User’s Guide
Copyright 2003 CONTEC CO., LTD. ALL RIGHTS RESERVED.
CONTEC CO., LTD. December 2004 Edition
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan Japanese http://www.contec.co.jp/ English http://www.contec.com/ A-46-785 (LYCY311) Chinese http://www.contec.com.cn/ 12212004_rev2 [09022003]
No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., LTD.
Loading...