Contec IPC-DT/L40S(PC)T, IPC-DT/H40X(PC)T User Manual

IPC Series

FLAT PANEL DISPLAY
For PanelLink

IPC-DT/L40S(PC)T
IPC-DT/H40X(PC)T

User’s Manual

CONTEC CO.,LTD.

Copyright

Copyright 2001 CONTEC CO., LTD. ALL RIGHTS RESERVED
No part of this document may be copied or reproduced in any form

by any means without prior written consent of CONTEC CO., LTD.

CONTEC CO., LTD. makes no commitment to update or keep
current the information contained in this document.
The information in this document is subject to change without
notice.

All relevant issues have been considered in the preparation of this
document. Should you notice an omission or any questionable
item in this document, please feel free to notify
CONTEC CO., LTD.

Regardless of the foregoing statement, CONTEC assumes no
responsibility for any errors that may appear in this document or for
results obtained by the user as a result of using this product.

Trademarks

MS, Microsoft, Windows, Windows NT and MS-DOS are
trademarks of Microsoft Corporation. Other brand and product
names are trademarks of their respective holder.

User’s Manual

i

Table of Contents

Copyright...........................................................................i

Trademarks........................................................................ i

Table of Contents.............................................................. ii

1.Introduction.......................................................................1

Features........................................................................ 1

Limited One-Year Warranty........................................ 2

How to Obtain Service................................................. 2

Liability ........................................................................ 2

Handling Precautions.................................................. 3

2.Specifications.....................................................................7

Function Specifications.................................................... 7

General Specifications ..................................................... 8

Optical Display Specifications......................................... 9

3.Outside Dimensions and Part Names............................11

Outside Dimensions........................................................11

Part Names..................................................................... 14

4.Setting the Display .........................................................15

Setting the DIP switch................................................... 15

Specifications of Remote Control Cable Connector...... 16

Connector application example................................. 16

5.Installation Procedure ....................................................17

6.Connection to the Host Computer and Power Supply ...19

Setting up the Host Computer....................................... 19

Connection Example ...................................................... 23

Power Supply.................................................................. 24

Panel Link Connector Specifications ............................ 25

7.Touch Panel..................................................................... 27

8.Options ............................................................................29

ii

User’s Manual

1. Introduction

The IPC-DT/L40S(PC)T and IPC-DT/H40X(PC)T are TFT color
liquid crystal displays (LCDs) to be used with host computers such
as the CONTEC IPC Series and SBCs (s in g le -boa rd co mp u ters).

Features

- Full-bright, wide-angle-of-visibility type of liquid crystals
capable of displaying up to 262,144 colors

- Touch panel enables mouse-style keyboard-less operation .

- Panel Link Interface allowing a cable of up to 5 m in length to be
used

- Thin panel unit has a mounting depth of only 38mm (when input
directly to 5VDC terminal)

- Back-mounted, dedicated power supply unit [IPC-POA1 00D]
available as an option, enabling the LCD to be used with an AC
power supply

- Equipped with a connector for remote control to get the full
benefit of the LCD

- Front structure with IP65-compliant ingress protection

* For the host computer to be used with the display or its options,

contact your local CONTEC branch or sales office.

1. Introduction

User’s Manual

1

1. Introduction

Limited One-Year Warranty

CONTEC Products are warranted by CONTEC CO., LTD. to be
free from defects in material and workmanship for up to one year
from the date of purchase by the original purchaser.

Repair will be free of charge only when this device is returned
freight prepaid with a copy of the origina l invoic e and a Return
Merchandise Authorization to the distributor or the CONTEC group
office, from which it was purchased.

This warranty is not applicable for scratches or normal wear, but
only for the electronic circuitry and original products. The
warranty is not applicable if the device has been tampered with or
damaged through abuse, mistreatment, neglect, or unreasonable use,
or if the original invoice is not included, in which case repairs will
be considered beyond the warranty policy.

How to Obtain Service

For replacement or repair, return the device freight prepaid, with a
copy of the original invoice. Please obtain a Return Merchandise
Authorization Number (RMA) from the CONTEC group office
where you purchased before returning any product.

* No product will be accepted by CONTEC group without the

RMA number.

Liability

The obligation of the warrantor is solely to repair or replace the product.
In no event will the warrantor be liable for any incidental or
consequential damages due to such defect or consequences that arise
from inexperienced usage, misuse, or malfunction of this device.

2

User’s Manual

Handling Precautions

Take the following precautions when handling this bo ard.

- This display is made of the precise electric parts, so do not use or
store it in the vicinity of impulse or vibration.

- Do not use or store the product in a location exposed to extremely
high or low temperature or susceptible to rapid temperature
changes.
Example: - Exposure to direct sun

- In the vicinity of a heat source

- There are switches and jumpers on the board that need to be set in
advance. Be sure to check these before installing to the
expansion slot. Only set the switches and jumpers on the board
to the specified settings. Otherwise, the product may cause a
failure.

- Do not use the product in extremely humid or dusty locations.

- This product is not intended for use in aerospace, space, nuclear
power, medical equipment, or other applications that require a
very high level of reliability. Do not use the product in such
applications.

- If you utilize this product in such usages where high reliability
and safety are required as on the trains, vessels, automotives or
crime- or disaster-prevention devices, contact your retailer.

- Do not use touch panel key operations to initiate actions where
there is a risk of loss of life or serious injury. Ensure that the
system design can handle the case when a key is pressed by
mistake.

- Do not use any sharp-pointed object such as a mechanical pencil
to touch the touch panel. Doing so may scratch the touch panel,
resulting in malfunctions.

- Do not subject the touch panel to shock as doing so may break it.

- Do not modify the product. CONTEC will bear no
responsibility for any problems, etc., resulting from modifying
this product.

- Use the power supply intended for use with this unit whenever
possible. If using a power supply other than the intended power
supply, ensure that it satisfies the required voltage and maximum
current ratings.

- Never disconnect the display cable when the ho st computer is
turned on. To avoid damage to the display, turn off the computer
before inserting or disconnecting the display cable.

- In the event of failure or abnormality, contact your retailer.

1. Introduction

User’s Manual

3

1. Introduction

- When the surface or frame of the touch panel has become dirty,
wipe it with neutral detergent. Do not wipe the touch panel with
thinner, alcohol, ammonia, or a strong chlorinated solvent. Use
a protective sheet (available as an option) if the touch panel is
used where it can easily collect dust and dirt.

- This display does not support the OS other than the following OS.
Windows 2000 Professional, Windows NT 4.0 Workstation,
Windows 98 Second Edition

- A characteristic of analog touch panels is that the detected
position may vary due to changes in the ambient environment
(temperature and humidity) and chan g es in re sis tan c e valu es ov er
time. In such cases, the touch panel should be recalibrated and
the calibration data updated.

- LCD display may have some pixels being dropped (bright and
black spots) below a certain threshold.
Note that this is not a failure or a defect.

- Regular maintenance is necessary for the backlight on the touch
panel and the display for the longevity parts.

Burn-in on TFT Display

- "Burn-in" may occur if the same display is retained for a long
time. Avoid this by periodically switching the display so that
the same display is not maintained for a long time.

* Burn-In---Phenomenon characterized by a TFT display as a result

of long-time display of the same screen where a
shadow-like trace persists because electric charge
remains in the LCD element even after the patterns are
changed.

- Component Life

(1) backlight--- The operating lifetime of the backlight is at least

seven years. (Brightness reduced to 50% of
original, assuming continuous operation at 25
degrees centigrade, Utilization rates 18 hours/one)

(2)Touch panel--- The operating lifetime of the touch panel is at

least 1 million touches (as tested by
mechanical touching under 300g of force at a
rate of two presses per second).

* CONTEC accepts your request for replacing each consumable in

the PANECON-PC as a request forrepair (at an additional cost).
Contact your local retailer or CONTEC sales office.

4

User’s Manual

FCC PART 15 Class A Notice

NOTE

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference at his own expense.

WARNING TO USER

Change or modifications not expressly approved the manufacturer can void the user's authority to
operate this equipment.

1. Introduction

User’s Manual

5

1. Introduction

6

User’s Manual

2. Specifications
Function Specifications

Table 2.1. Function Specifications

Item

Assembly type Panel mounted
Screen size 12.1 inches 15 inches
Number of pixels 800 x 600 dots 1024 x 768 dots
Display type TFT color LCD
Number of colors 262,144 colors
Brightness control Provided by software and hardware

Backlight control Provided by software and hardware

Cable length 2m or 5m (use the special-purpose display cable sold separately.)
LCD interface 20-pin MDR connector (Panel Link Interface used) *1
Power supply interface 4-pin nylon connector for +5 VDC power supply

Resolution 4096 x 4096 (Emulated in 800 x 600) 4096 x 4096 (Emulated in 1024 x 768)

Touch
panel

Detection method Resistive-layer analog method
Touch life expectancy The operating lifetime of the touch panel is at least 1 million touches

Touch panel interface 20-pin MDR connector on the back (shared with display signals)

Power consumption 3.3A Max. at +5 VDC±5% 4.0A Max. at +5 VDC±5%

IPC-DT/L40S(PC)T IPC-DT/H40X(PC)T

(Remote control cable connector on the back)

(Remote control cable connector on the back)

(Input at 85 to 264 VAC is enabled by using the back-mounted, optional
power supply unit [IPC-POA100D].)

(as tested by mechanical touching under 300g of force at a rate of two presses
per second)

Specification

2. Specifications

*1 : When used for output to the LCD, the CONTEC IPC or SBC series requires a converter such
as the LCD signal conversion unit [ADPLNK(PC)H] depending on the model of the host.
Check this out before purchase.

User’s Manual

7

2. Specifications

General Specifications

Table 2.2. General Specifications

Condition

Environment

Ambient operating temperature 0 - 50°C
Ambient storage temperature -10 - 60°C
Ambient humidity 10 - 90%RH (No condensation )
Floating dust Normal
Corrosive gas None
Noise

resistance

Vibration
resistance

Shock resista n c e 10 G in the X/Y/Z d irections for 11 ms; Ha l f-sine wave

Structure

Major dimensions (mm) 370(W) x 40.4(D) x 307(H) 428(W) x 40.4(D) x 336(H)
Panel cut dimensions (mm) 344±0.5(W) x 281± 0 .5(H)

Weight About 4.0 kg (*2) About 5.0 kg (*2)
Ingress protection Front part conforming to IP65

*2: The weight includes neither cables nor the optional power supply.

Line noise AC line: 2 kV, Signal line: 1 kV

Electrostatic
withstanding
voltages

Sweep durability 10 - 50 Hz/Single-side amplitude or 0.15 mm

Fixed-vibration
durability

IPC-DT/L40S(PC)T IPC-DT/H40X(PC)T

(IEC1000-4-4Level3, EN61000-4-4Level3)
(Host: IPC-BX/M600(PCW), Power supply: IPC-POA100D)

Contact: 4 kV (IEC1000-4-2 Level 2, EN61000-4-2 Level 2)
Airborne: 8 kV (IEC1000-4-2 Level 3, EN61000-4-2 Level 3)
(Host: IPC-BX/M600(PCW), Power supply: IPC-POA100D)

50 - 500 Hz/2.0 G in the X/Y/Z directions for 23 mi n ut es ea ch
(Conforming to JIS C0040 and IEC68-2-6)

16.7 Hz/2 G in the X/Y/Z directions for 30 minutes each
(Conforming to JIS C0040 and IEC68-2-6)

(Conforming to JIS C0041 and IEC68-2-27)

(12 stud holes are required on
the periphery.)

Specification

398±0.5(W) x 306±0.5(H)
(12 stud holes are required on the
periphery.)

8

User’s Manual

Optical Display Specifications

Table 2.3. Optical Display Specifications

Item Condition

Visual angle
(Up/Down)

Visual angle
(Right/Left)

Surface brightness
(at center) *1
*1 Surface brightness is a numerical value in a display simple substance. The brightness that let the

touch panel pass serves as about 77% of the above-mentioned numerical value.

Left
( φ =

-

90o )

( θ = 0

CR≥10

o

φ = 180° 50deg 50deg

φ = 0° 70deg 60deg

Display in

monochrome

φ = +90° 70deg 75deg

φ= -90°

Display in white 350cd/m2 (Typ.) 250cd/m2 (Typ.)

Measurement direction

Z

)

θ

Top

o

)

( φ = 180

2. Specifications

Specifications

IPC-DT/L40S(PC)T IPC-DT/H40X(PC)T

70deg 75deg

Note!

User’s Manual

X

Bottom
( φ = 0

φ

o

)

Y

Module

Right
( φ = 90

o

)

Figure 2.1. Viewing Range Definition

The above optical specification data shows optical characteristics
of the liquid crystal in the display; the data does not represent the
actual view on the display or its viewing angles.

9

2. Specifications

10

User’s Manual

3. Outside Dimensions and Part Names

3. Outside Dimensions and Part Names
Outside Dimensions

IPC-DT/L40S(PC)T

12-M4 STUD

370

251

99.7589.75

307

2.438

13

98 9898

279

Figure 3.1. Out side Dimensions of Main Unit

(IPC-DT/L40S(PC)T)

IPC-DT/H40X(PC)T

12-M4 STUD

428

310.1

13

38 2.4

106

4-M4 TAP
(Maximum tapping length : 7mm)

119 119 119

100

137 137 137

342

100

396

100

[mm]

236.7

336

7

User’s Manual

304

100

7

CONTEC

4-M4 TAP
(Maximum tapping
length:4mm)

[mm]

302

157.5

254

138

4-M4 TAP (Including the mate)
Maximum tapping length:4mm)

107106

4-M4 TAP (Including the mate)
Maximum tapping length:4mm)

Figure 3.2. Out side Dimensions of Main Unit

(IPC-DT/H40X(PC)T)

11

3. Outside Dimensions and Part Names

IPC-DT/L40S(PC)T with IPC-POA100D (power supply unit)

119 119 119

342

12-M4 STUD

58

13

2.438
370

98 9898

279

17

Figure 3.3. Dimensions of IPC-DT/L40S(PC)T with

IPC-DT/H40X(PC)T with IPC-POA100D (power supply unit)

137 137 137

107 106106

304

280

14048.5(85)

IPC-POA100D

396

67

12-M4 STUD

58

13

67

307

[mm]

2.438

336

428

167113

(85)

17

16721.5

Figure 3.4. Dimensions of IPC-DT/H40X(PC)T with

IPC-POA100D

12

[mm]

User’s Manual

45mm

20mm

Figure 3.5. Cable Bend Dimension

3. Outside Dimensions and Part Names

User’s Manual

13

3. Outside Dimensions and Part Names

Part Names

Panel Link connector

Remoto control cable connector

DIP-SW

5VDC power supply connecotr

Figure 3.6. Pa rt Names (IPC -D T/L40S(PC ) T and

IPC-DT/H40X(PC)T)

Touch panel over liquid crystals

Power LED

14

User’s Manual

4. Setting the Display

Be sure to check the following settings before using the display.

Setting the DIP switch

The display has a DIP switch (an array of built-in switches) on the
back. For normal use of the display, leave all of the built-in
switches at the OFF positions (as factory-set). The table below
shows the functions of the built-in switches.

1234

ON

Figure 4.1. DIP Switch
Table 4.1. DIP Switch Settings

No. ON/OFF setting Function

OFF (Factory setting) Enable the display built-in buzzer to sound upon a touch on the

1

touch panel. (The buzzer ON/OFF setting can also be controlled
by driver software.)

ON Disable the display built-in buzzer from sounding upon a touch on

the touch panel. (The buzzer ON/OFF setting can also be

controlled by driver software.)
OFF (Factory setting) Use a host other than below.2
ON Use an SBC board PC-686C(PC)H-LV , -LVS

IPC-BX/M620(PCW) Series, or IPC-BX/M630(PCI) Series.
OFF (Factory setting) No function3
ON No function
OFF (Factory setting) No function4
ON No function

4. Setting the Display

Notes!

User’s Manual

- The buzzer is disabled by setting the DIP switch (built-in switch
No. 1 to ON).

- Set built-in switch No. 2 depending on the host product to be
used with the display.

15

4. Setting the Display

Specifications of Remote Control Cable

Connector

The display has the remote control cable connector on the back.
Given below are the pin assignments on the connector and an
example of using it.

Table 4.2. Remote Control Cable Connector

Connector type

Model

Pin No.

1
2
3
4
5
6

*1 : The backlight remains off while the backlight ON/OFF signal has the GND level.

Connector application example

Cable connector (Side type)

S6B-XH-A(LF)(SN)(mfd. by JST)

1 2 3 4 5 6

Signal name
Brightness UP
GND
Brightness DOWN
GND
Backlight ON/OFF *1
GND

Pushbutton switches (SW1, SW2)

1
2
3
4
5
6

Connector model: XHP-6 (JST)

SW1

SW2

SW3

ON/OFF switch (SW3)

Figure 4.2. Connector Application Example

Notes!

- Applying a GND-level voltage to the brightness UP or DOWN
signal increases or decreases the brightness.

- The brightness remains unchanged if the two signals (brightness
UP and DOWN signals) are input at the same time.

- The remote control cable is not bundled with this prod uct.

16

User’s Manual

5. Installation Procedure

(1) Cut a panel in the following dimensions for installing the

display.
The four corners of the solid-line rectangle define the panel cut
dimensions. The holes (12) on dashed lines represent stud
holes.

5. Installation Procedure

119 119119

281

98 9898

12 φ 05

344

Figure 5.1. Display Mounting Position

(IPC-DT/L40S(PC)T)

137 137137

306

398

[mm]

User’s Manual

106 106107

12 φ 05

[mm]

Figure 5.2. Display Mounting Position

(IPC-DT/H40X(PC)T)

17

5. Installation Procedure

(2) Insert the supplied gasket between the panel and the display,

Panel

Figure 5.3. Assembling Method

Note!

The panel must be up to 10 mm in thickness.

then fasten them together w ith M4 nu ts a s shown be low.

Display

Gasket

18

User’s Manual

6. Connection to the Host Computer and Power Supply

6. Connection to the Host Computer and Power
Supply

If using IPC or SBC products other than those listed here, refer to
their respective manuals for details of the settings.

Setting up the Host Computer

The IPC-DT/L40S(PC)T and IPC-DT/H40X(PC)T can be used with
host computers such as the CONTEC IPC Series and SBCs (single­board computers). The host computer to be connected must be set
up correctly for using the display. Set the IPC-DT/L40S(PC)T to
SVGA (800 x 600) or the IPC-DT/H40X(PC)T to XGA (1024 x

768).
Set the LCD type as follows depending on the host computer to be

used.

PC-686BX(PC)-LV

To use this SBC board with the display, set the on-board switch
(U2) as shown below.

Note!

User’s Manual

12.1-inch IPC-DT/L40S(PC)T 15-inch IPC-DT/H40X(PC)T
U2 U2

ON

12345678

Set all bits to OFF.

(TFT color LCD in 800 x 600) (TFT color LCD in 1024 x 768)

ON

12345678

Set only 1 to ON

Figure 6.1. U2 Switch Settings

Use this board along with the ISA bus type of LCD signal
conversion board [ADPLNK(PC)].

19

6. Connection to the Host Computer and Power Supply

PC-686C(PC)-LV or -LVS

Since this SBC board is Plug and Play compliant, there is no need
to set up the host computer.

Instead, set the DIP built-in switch No. 2 to ON. (See Chapter 4.)

Note!

Use this board along with the 26/20-pin conversion cable
[IPC-PL2620-002/C].

PC-686E(PC)-LV

To use this SBC board with the display, set the on-board rotary
switch as shown below.

Table 6.1. PC-686E(PC)-LV

12.1-inch IPC-DT/L40S(PC)T 15-inch IPC-DT/H40X(PC)T

Setting No. = 0 (TFT color LCD in 800 x 600) Setting No. = 1 (TFT color LCD in 1024 x 768)

Note!

Use this board along with the ISA bus type of LCD signal
conversion board [ADPLNK(PC)].

20

User’s Manual

6. Connection to the Host Computer and Power Supply

PC-586U(PC)-LV or -LVS

To use this SBC board with the display, set the on-board switch (S2)
as shown below.

12.1-inch IPC-DT/L40S(PC)T 15-inch IPC-DT/H40X(PC)T
S2 S2

ON

ON

Note!

1234

Set all bits to OFF. Set only 1 to ON.

(TFT color LCD in 800 x 600) (TFT color LCD in 1024 x 768)

1234

Figure 6.2. S2 Switch Settings

Use this board along with the LCD signal conversion mini-board
[EXLCD68] and the ISA bus type of LCD signal conversion board
[ADPLNK(PC)].

PC-586HU(PC)-LV

To use this SBC board with the display, set the on-board jumper
(JP8) as shown below.

12.1-inch IPC-DT/L40S(PC)T
JP8

7
8

Leave all pins unconnected. Connect only the 1-2 pins.

(TFT color LCD in 800 x 600)

1
2

15-inch IPC-DT/H40X(PC)T

JP8

7
8

(TFT color LCD in 1024 x 768)

1
2

Note!

User’s Manual

Figure 6.3. JP8 Setting

Use this board along with the ISA bus type of LCD signal
conversion board [ADPLNK(PC)].

21

6. Connection to the Host Computer and Power Supply

IPC-BX/M600(PCW)

To use this box computer with the display, set the on-board switch
(S1) as shown below.

12.1-inch IPC-DT/L40S(PC)T 15-inch IPC-DT/H40X(PC)T
S1 S1

ON

ON

12345678

Set 5, 6, and 7 to ON.

(TFT color LCD in 800 x 600) (TFT color LCD in 1024 x 768)

12345678

Set 6, 7, and 8 to ON.

Figure 6.4. S1 Switch Settings

22

User’s Manual

Connection Example

Illustrated below is an example of connecting the display to the box
computer [IPC-BX/M600(PCW)C, CP].

IPC-BX/M600(PCW)C, CP

Panel Link cable(Option)
[IPC-PL2020-020] (2m)
[IPC-PL2020-050] (5m)

Display

-IPC-DT/L40S(PC)T

-IPC-DT/H40X(PC)T

Figure 6.5. System Configuration

6. Connection to the Host Computer and Power Supply

5VDC

User’s Manual

23

6. Connection to the Host Computer and Power Supply

Power Supply

The display operates at 5VDC. For the supply voltage, use a
power supply satisfying at least the capacity defined in the
Specifications.
Turn the 5VDC supply On in accordance with the following
sequence.

1 - 50ms

(Rise time to 4.75V)

+5V

0V

Figure 6.6.

Power On Sequence

Table 6.2. Power Supply Connector

Connector type

Model

Pin No.

5VDC input connector
B4PS-VH(LF)(SN)(mfd. by JST)

Signal name
1
2
3
4

GND
GND

+5V
+5V

4321

Applicable power cable connector

Housing: VHR-4N (manufactured by JST)
Contact: SVH-21T-1.1(LF)(SN)(AWG22 - 18)

(manufactured by JST)

Although the display operates at 5VDC, the dedicated 5VDC output
AC power supply [IPC-POA100D] is available as an option so that
the display can be used with an AC power supply.

24

User’s Manual

6. Connection to the Host Computer and Power Supply

Panel Link Connector Specifications

The display is equipped with the Panel Link Interface. The table
below lists the pin specifications of the Panel Link connector on the
back of the display.

Table 6.3. Panel Link Connector

Connector type

Model

Panel Link Interface connector(CN3)
N10220-5DG3 PL(mfd. by 3M)

A1A10

Pin No.

A1
A2
A3
A4
A5
A6
A7
A8
A9

A10

B10

TX0-

TX0+
TX0 SHIELD
TX2 SHIELD

TX2-

TX2+

DDC/SCL
DDC/SDA

TXD(HOST)

RXD(HOST)

B1
B2
B3
B4
B5
B6
B7
B8
B9

B10

B1

Signal namePin No.Signal name

TXC-

TXC+
TXC SHIELD
TX1 SHIELD

TX1­TX1+

N.C.

SENS

N.C.

GND

User’s Manual

25

6. Connection to the Host Computer and Power Supply

26

User’s Manual

7. Touch Panel

The IPC-DT/L40S(PC)T) and IPC-DT/H40X(PC)T is equipped
with a quick response touch panel which enables keyboard-less,
mouse-less operations using the serial interface (RS-232C) with the
host computer.

CPU

7. Touch Panel

Touch panel

Host PC Touch panel controller Touch panel

Serial controller

NS16550 compatible

8bit CPU

INT

Serial

communication

Figure 7.1. Touch Panel and Block Diagram

Data input at the touch panel is processed by the touch panel
controller and passed to the host PC via the serial port on the CPU
in the controller.

Before the touch panel can be used, touch panel driver software
(TPBK(PC)S) must be installed. Note that the driver software is
not bundled with this product. Use th e one (to be) downloadable
from the CONTEC’s home page or the one included on the driver
software CD-ROM (IPC-SLIB-01) available as an option
(separately priced). The CD-ROM need to be purchased
separately.

The touch panel driver supports Windows 95, 98, NT4.0, and 2000.
For further details, refer to the READ_ME file for each driver.

Communication format

- Baud rate 9600

- Data length 8 bits

- Parity Even parity

- Stop bit 1 bit

User’s Manual

27

7. Touch Panel

28

User’s Manual

8. Options

Double-sided screen protective sheets

- IPC-CV12 : (12.1-inch screen protective sheets: 10
sheets)

- IPC-CV15 : (15-inch screen protective sheets: 10 sheets)

Driver

- IPC-SLIB-01 : Driver & Utility Soft Set(CD-ROM version)

Power unit

- IPC-POA100D : 100V to 240VAC power unit

- IPC-POD24/5 : 24VDC input power unit

LCD I/F board

- ADPLNK(PC)H : Panel Link I/F board for SBC(ISA bus)

Optional cables

- IPC-PL2020-020 : Panel link cable (2 m)

- IPC-PL2020-050 : Panel link cable (5 m)

- IPC-DVIPL-020 : DVI - panel link conversion display cable
(2m)

- IPC-DVIPL-050 : DVI - panel link conversion display cable
(5m)

8. Options

User’s Manual

29

IPC-DT/L40S(PC)T

IPC-DT/H40X(PC)T

User’s Manual

IPC-DT/x40x-HMU

CONTEC CO.,LTD.

3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Japanese http://www.contec.co.jp/
English http://www.contec.com/
Chinese http://www.contec.com.cn/

No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD. [08012007]

[02222001] Management No. A-46-452
[08012007_rev7] Parts No. LZS9912

August 2007 Edition