Contec IPC-DT/M61VT-DC1, IPC-DT/S61VT-DC1, IPC-DT/M61VT-AC0, IPC-DT/L61SVT-DC1, IPC-DT/L61SVT-AC0 User Manual

IPC Series

Flat Panel Display
IPC-DT/61 Series

User’s Manual

CONTEC CO.,LTD.

Copyright

Copyright 2004 CONTEC CO., LTD. ALL RIGHTS RESERVED.
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.

CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this
document. The information in this document is subject to change without notice.

All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.

Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document nor for results obtained by the user as a result of using this product.

Trademarks

MS, Microsoft, MS-DOS and Windows are trademarks of Microsoft Corporation. Other brand and
product names are trademarks of their respective holder.

User’s Manual

i

Table of Contents

Copyright .............................................................................................................................................i

Trademarks ..........................................................................................................................................i

Table of Contents................................................................................................................................ii

1. Introduction 1

Features...............................................................................................................................................1

Customer Support...............................................................................................................................2

Web Site....................................................................................................................................... 2

Limited One-Year Warranty............................................................................................................... 2

How to Obtain Service ....................................................................................................................... 2

Liability .............................................................................................................................................. 2

Safety Precautions .............................................................................................................................. 2

Safety Information....................................................................................................................... 3

Handling Precautions................................................................................................................... 3

2. Specifications 7

Function Specifications...................................................................................................................... 7

General Specifications........................................................................................................................ 9

Optical Display Specifications......................................................................................................... 10

3. Outside Dimensions and Part Names 11

Outside Dimensions.......................................................................................................................... 11

Part Names ........................................................................................................................................ 15

Analog RGB Connector............................................................................................................. 1 8

RS Touch Panel Connector........................................................................................................18

USB Touch Panel Connector.....................................................................................................19

DVI-D Connector ......................................................................................................................20

4. Hardware Setup 21

Installation Requirements................................................................................................................. 21

Panel Cut........................................................................................................................................... 21

Attaching the Fit ti ng Used to A tta ch to th e Ma in Un it............................................................. 23

5. Connection to the Host Computer 25

Analog RGB Connection.................................................................................................................. 25

DVI-D Connection ...........................................................................................................................26

Touch Panel Data Communications................................................................................................. 29

User’s Manual

ii

6. Power Supply Connection 31

AC input type ................................................................................................................................... 31

DC input type ................................................................................................................................... 32

Power Supply Connecto r ........................................................................................................... 32

AC Adapter Jack........................................................................................................................ 33

AC adapter code removal prevention fitting.................................................................................... 34

7. Screen Adjustment and a Setup 35

Menu Screen..................................................................................................................................... 35

Direct Key......................................................................................................................................... 40

Memory of a Setting Value.............................................................................................................. 40

8. LED Indicators 41

9. Touch Panel 43

USB Multi-Touch Panel................................................................................................................... 44

10. Display Mode 45

11. Options 47

User’s Manual

iii

User’s Manual

iv

1. Introduction

1. Introduction

This product is a dual-input (analog RGB and DVI-D), panel-mounted, color TFT LCD display unit for use
with host computers such as the CONTEC IPC series and SBCs (single board computers).

Features

- Full-bright, wide-angle-of-visibility type of liquid crystals capable of displaying up to 262,144
colors (16,777,216 colors on the IPC-DT/H61XT-DC1 and AC0)

- Standard analog RGB input for screen. RS-232C and USB interfaces for touch panel.

- Multiple touch panel configurations containing up to eight touch panels are supported when using
the USB touch panel interface.

- Auto-scaling feature that resizes the input screen to the LCD dot configuration.

- On-screen display setup menu facilitating screen adjustment

- Dual-input function supports analog RGB and DVI-D inputs. The display can be connected to two
different computers at o nce. (Simultane ous displa y is not sup ported. Scree ns are switche d using the
OSD.)

- Analog touch panel enabling mouse emulation using driver software

- Optional AC adapter (IPC-ACAP12-01) available for AC power supply.

- Front structure with IP65-compliant ingress protection

- Optional stand kit available for desktop use.

- A special fitting is provided to prevent the AC adapter cable from being unplugged.

User’s Manual

1

1. Introduction

Customer Support

CONTEC provides the following s upport services fo r you to use CONTEC products more efficiently and
comfortably.

Web Site

Japanese http://www.contec.co.jp/
English http://www.contec.com/
Chinese http://www.contec.com.cn/

Latest product information
CONTEC provides up-to-date information on products.

CONTEC also provides product manuals and various technical documents in the PDF.
Free download

You can download updated driver software a nd diff erenti al files as we ll as sample pr ograms available i n
several languages.

Note! For product information
Contact your retailer if you have any technical question about a CONTEC product or need its price,

delivery time, or estimate information.

Limited One-Year Warranty

CONTEC Products are warranted by CONTEC CO., LTD. to be free from defects in material and
workmanship for up to one year from the date of purchase by the original purchaser.
Repair will be free of char ge only w hen thi s device is ret urned fr eight pr epaid with a c opy of t he origi nal
invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office, from
which it was purchased.
This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and
original products. The warranty is not applicable if the device has been tampered with or damaged
through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in
which case repairs will be considered beyond the warranty policy.

How to Obtain Service

For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please
obtain a Return Merchandise Authorization Number (RMA) from the CONTEC group office where you
purchased before returning any product.
* No product will be accepted by CONTEC group without the RMA number.

Liability

The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor
be liable for any incidental or consequential damages due to s uch defec t or consequence s that arise from
Safety Precautions. Understand the following definitions and precautions to use the product safely.

Safety Precautions

Understand the following definitions and precautions to use the product safely.

User’s Manual

2

1. Introduction

Safety Information

This document provides safety information u sing the foll owing sym bols to prevent a ccidents res ulting in
injury or death and the destructi on of equi pment an d reso urce s. Unders tand t he meanin gs of t hese labe ls
to operate the equipment safely.

DANGER

WARNING

CAUTION

DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury or in property damage.

Handling Precautions

CAUTION

- As this product contains precision electronic components, do not use or store in environments
subject to shock or vibration.

- Do not use or store the product in a location such as extremely high or low temperature, rapid
temperature changes, and the place which receives a strong ultraviolet ray.
Example: - Exposure to direct sun

- In the vicinity of a heat source

- Some products require configuration settings. Always check these requirements before use. Also,
never set switches or jumpers to other than the specified settings as this may cause a fault.

- Do not use or store the equipment in a dusty or humid place.

- If you discover damaged or missing items, contact your retailer.

- Do not perform key operations w ith the t ouc h pan el to implement a process that migh t endan ger li fe
or result in serious damages. Design a system that can cope with incorrect key input operations.

- Do not use a sharp-edged object, such as a mechanical pencil, to operate the touch panel in order to
prevent scratching or malfunctions.

- Protect the touch panel against shock to prevent damage.

- CONTEC is not liable for a product that has been modified by the user.

- For this equipment, use the dedicated power supply unit if po ssible. If y ou conne ct any oth er power
supply unit, be sure to select the one that satisfies the voltage and current capacity standards.

- Never supply power to the power supply con nector and the AC adapter jack at the same time as it
can cause a fault.



User’s Manual

3

1. Introduction

- When the surface or frame of the touch panel has become dirty, wipe it with neutral detergent. Do
not wipe the touch panel with thinner, alcohol, ammonia, or a strong chlorinated solvent.

- Do not plug or unplug the connector with the equipment powered on. as doing so may result in a
malfunction or fault.

- This product is not intended for use in aerospace, space, nuclear power, medical equipment, or other
applications that require a very high level of reliability. Do not use the product in such applications.

- If you utilize this product in such usages where high reliability and safety are required as on the
trains, vessels, automotives or crime- or disaster-prevention devices, contact your retailer.

Use environment
This product operates under the following operating systems:

Windows XP/2000/NT 4.0/98SE/95OSR2, MS-DOS 6.2
* The touch panel USB interface is only supported on Windows XP/2000/98SE.

Life expectancy of components

(1) Backlight--- Display brightness decreases over time with use. The operating life of the backlight

(brightness reduced to 50% of original) is 50,000 hours for all models. (As su ming
continuous operation at 25 degrees centigrade.)

(2) Touch panel--- The operating lifetime of the touch panel is at least 1 million touches (as tested by

mechanical touching under 300g of force at a rate of two presses per second).

(3) Power supply (AC adapter) --- Expected life is six years for continuous operation at 40°C (when

mounted horizontally). However, this life may be reduced
depending on the operating temperature (in the case of higher
temperatures).

* CONTEC accepts your request for replacing each consumable in the PANECON-PC as a request for

repair (at an additional cost). Contact your local retailer or CONTEC sales office.

LCD Display Pixel Drop
LCD display may have som e pixels being dr opped (brig ht and black spots) below a certain thr eshold.

Note that this is not a failure or a defect.

Burn-in on TFT Display
"Burn-in" may occur if the same display is retained for a long time. Avoid this by periodically

switching the display so that the same display is not maintained for a long time.

* Burn-In: Phenomenon characterized by a TFT display as a result of long-time display of the same

screen where a shadow-like trace persists because electric charge remains in the LCD element even
after the patterns are changed.

User’s Manual

4

1. Introduction

Connecting to a host with an existing touch panel function such as a CONTEC panel computer.
This touch panel cannot be used with a touch panel mounted in the host computer. In this case, the

touch panel function will be unavailable but screen display will still work normally.
However, on the following CONTEC panel computers, multiple touch panels can be used together
when connected via the USB interface.

- IPC-PT/630 Series: IPC-PT/H630X(PCI)C, IPC-PT/H630X(PCI)CP ,

IPC-PT/L630S(PCI)C, IPC-PT/L630S(PCI)CP

- IPC-PT/620 Series: IPC-PT/H620X(PCW)C, IPC-PT/H620X(PCW)CP ,

IPC-PT/L620S(PCW)C, IPC-PT/L620S(PCW)CP

- IPC-PT/600 Series: IPC-PT/H600X(PCW)C, IPC-PT/H600X(PCW)P ,

IPC-PT/L600S(PCW)C, IPC-PT/L600S(PCW)P

User’s Manual

5

1. Introduction

User’s Manual

6

2. Specifications

2. Specifications
Function Specifications

Table 2.1. Function Specifications

Item

Screen

Assembly type
Screen size 6.5 inches 10.4 inches 12.1 inches 15.0 inches
Number of pixels 640 x 480 dots 640 x 480 dots 800 x 600 dots 1024 x 768 dots
Display type TFT Color LCD
Number of colors 262,144 colors 262,144 colors 262,144 colors 16,777,216 colors
Screen adjustment Automatic adjustment (display positioning and scaling) and manual

Brightness control Adjustment using the front switch or software control from the host computer
Backlight control
Display interface Analog RGB input HD-SUB 15 pin (Female) connector

Incoming
signal
specification

Cable length which recommends 5mm or less *3

Touch panel
Resolution 4096 x 4096
Detection method Resistive-layer analog method
Touch life expectancy One million repeated touches (silicon rubber load of 3 N)
Touch panel interface

Touch panel driver
(option)

*1

Optional desk stand IPC-SND-03 allowing desktop installation

*2 If the outp ut is f rom a CON TEC IPC se rie s or SB C seri e s mode l, an IS A bus ty pe pa nel lin k I/F boa rd

(ADPLNK(PC)H) is required for some models. Please confirm before purchasing.

*3 Using a cable longer than 5 m may reduce the im ag e q ualit y. T he cabl e shoul d be a s sho rt as possible a s

degradation. in image quality may result even when the cable is 5 m or shorter depending on the type of host
computer or cable.

*4 The touch panel USB interface is only supported on Windows XP/2000/98SE.

Analog
RGB input

DVI-D input Digital RGB (complie s with TMDS ) *2

IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1

Panel mounted, desktop *1

adjustment using the front switches

Can be turned on or off by an OSD switch or via software control from the host
computer.

DVI-D input 24 pin DVI (Female) connector
Separate RGB, analog, positive polarity 0.7Vp-p/75Ω
Separate V/H, TTL, positive/negative polarity
Horizontal: 31 - 80kHz, vertical: 56 - 75 Hz

Connect to the host computer using either USB*4 or RS-232C.
USB: USB1.1-compli an t, Ty peB C onn ect or

RS-232C: 9pin D-SUB ( Male ) Co nne cto r

For Windows: IPC-SLIB-01
For MS-DOS: IPC-TPB1 -DRV

IPC-DT/M61VT-AC0

Specification

IPC-DT/L61SVT-DC1
IPC-DT/L61SVT-AC0

IPC-DT/H61XT-DC1
IPC-DT/H61XT-AC0

User’s Manual

7

2. Specifications

Table 2.2. Power Supply Specifications (DC Input Type)

Item

Power supply input part

Power supply connector
AC adapter jack
Input power supply voltage

Consumption curren t

Consumption curren t

(power save mode)

IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1 IPC-DT/L61SVT-DC1 IPC-DT/H61XT-DC1

4-pin nylon connector for 12 VDC power supply

AC adapter jack for 12 VDC power supply
(An optional AC adapter (IPC-ACAP12-01) can be used for 100 - 240VAC

input.)

+12VDC±5%

1.3A(Max.) 1.4A(Max.) 1.6A(Max.) 2.5A(Max.)

0.4A(Max.)

Specification

Table 2.3. Power Supply Specifications (AC Input Type)

Item

Power supply input part

Power supply connector Three-pin terminal block for the AC power supply
Input power supply voltage
Power consumption

Current consumption
(power save mode)

IPC-DT/M61VT-AC0 IPC-DT/L61SVT-AC0 IPC-DT/H61XT-AC0

Auto-switched 85 - 132VAC / 170 - 265VAC (47 - 63Hz) input
36VA (Max.) 40VA (Max.) 60VA (Max.)

14VA (Max.)

Specification

User’s Manual

8

2. Specifications

General Specifications

Table 2.4. General Specifications

Item Specification

Environment

Operating
temperature
Storage
temperature

Operating humidity
Floating dust Normal

Corrosive gas None

Noise
resistance

Vibration
resistance

Shock resistance 10 G in the X/Y/Z directions for 11 ms; Half-sine wave

Line noise

Electrostatic
withstanding
voltages

Sweep
durability

0 - 50ºC (0 - 40ºC when using an IPC-ACAP12-01 (AC switching adapter))

-10 - 60ºC
(20 - 80% when using an IPC-ACAP12-01 (AC switching adapter))

(No condensation allow ed)

AC line: 2 kV, Signal line: 1 kV
(IEC1000-4-4Level3, EN61000-4-4Level3)
(HOST: IPC-BX/M600(PCW) Power supply: IPC-POA200/12-01)

Contact: 4 kV(IEC1000-4-2Level2, EN61000-4-2Level2)
Airborne: 8 kV(I EC1 000 -4 -2L ev el3 , EN 61 00 0-4 -2L ev el3 )
(HOST: IPC-BX/M600(PCW) Power supply: IPC-POA200/12-01)

10 - 57 Hz/Single-side amplitude or 0.15 mm
57 - 150 Hz/2.0 G in the X/Y/Z directions for 23 minutes each
(Conforming to JIS C0040 and IEC68-2-6)

(Conforming to JIS C0041 and IEC68-2-27)

Table 2.5. Structure specification (DC Input Type)

Item

Structure

Major dimensio n (m m) 210(W) x 40(D) x

Panel cut dimensions
(mm)

Mountable panel
thickness
Weight

Ingress protection Front part conforming to IP65

IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1 IP C- DT /L61SVT-DC1 IPC-DT/H61XT-D C1

166(H)

199.0(W) x 155.0(H) 292.0(W) x 227.0(H) 303.0(W) x 243.0(H) 358.0(W) x 289.0(H)

1.6mm - 7mm

1.3kg 2.6kg 2.9kg 3.9kg

305(W) x 43.5(D) x
240(H)

Table 2.6. Structure specification (AC Input Type)

Item

Structure

Major dimensions (mm) 305(W) x 51.5(D) x

Panel cut dimensions
(mm)

Mountable panel

thickness

Weight 2.8kg 3.1k g 4.1kg
Ingress protection

IPC-DT/M61VT-AC0 IPC-DT/L61SVT-AC0 IPC-DT/H61XT-AC0

240(H)

292.0(W)×227.0(H) 303.0(W)×243.0(H) 358.0(W)x289.0(H)

1.6mm - 7mm

Front part conforming to IP65

316(W) x 54.5(D) x
256(H)

Specification

316(W) x 46.5(D) x
256(H)

Specification

376(W) x 46(D) x
305(H)

376(W) x 54(D) x
305(H)

User’s Manual

9

2. Specifications

Optical Display Specifications

Table 2.7. Optical Display Specifications

Item Condition

Visual angle
(vertical)

Visual angle
(horizontal)

Surface
brightness
(at center)

*1 Surface brightness is a numerical value in a display simple substance.

The brightness that let the touch panel pass serves as about 75% of the above-mentioned numerical value.

φ=180° 45deg 50deg 50deg 45deg

Display in

φ=0° 35deg 70deg 70deg 55deg

CR≥10

Display in white

monochrome

φ=+90° 50deg 70deg 70deg 60deg
φ=-90°

IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1

50deg 70deg 70deg 60deg

2

300cd/m

Measurem ent direction

Z

o

( θ = 0

)

Left

-

90o )

( φ =

θ

Top

o

)

( φ = 180

Specifications (25ºC Typ. Value)

IPC-DT/M61VT-AC0

400cd/m

IPC-DT/L61SVT-DC1
IPC-DT/L61SVT-AC0

2

350cd/m

IPC-DT/H61XT-DC1
IPC-DT/H61XT-AC0

2

260cd/m

2

X

Bottom
( φ = 0

φ

o

)

Right
( φ = 90

Y

Module

o

)

Figure 2.1. Viewing Range Definition

CAUTION

The above optical specification data shows optical characteristics of the liquid crystal in the displ ay;

the data does not represent the actual view on the display or its viewing angles.

User’s Manual

10

3. Outside Dimensions and Part Names

3. Outside Dimensions and Part Names
Outside Dimensions

IPC-DT/S61VT-DC1

4-M4 TAP

27

P

ES

CN

TI

PASS

2

12VDC-IN

CAUTION!

Don't connect 1 and 2 of
12VDC-IN simultaneously.
12VDC-IN*1*2***
************

(Maximum tapping
length : 5mm)

COM DVI VGA USB

1

50

(Maximum
tapping length
: 5mm)

154

M3 TAP

16

105

ESCMENU

-+

138
210

35

5

75

XXXXXXXXX

MODEL :

XXXXXXXXXXXXXXXXXX

CAUTION!

*************
******0.6N*m***

The screw bo lting torque of attachment
must be 0.6N-m(MAX)

SERIAL No. : XXXXXXXXXXXXX
INPUT : XXXXXXXXXXXXXXXXXX

XXXXXXXXX
XXXXXXXXX

75

198

Figure 3.1. Outside Dimensions of Main Unit(IPC-DT/S61VT-DC1)

IPC-DT/M61VT-DC1

58

166

POWER

[mm]

100

27.5

6.5

Figure 3.2.

User’s Manual

100

75

75

291

8-M4 TAP
(Maximum tapping
length : 5mm)

COM USBDVI VG A

212VDC-IN1

FG-+

CAUTION!

************

Don't connect 1 and 2 of

12VDC-IN simultaneou sly.

12VDC-IN*1*2***

49

226

M3 TAP
(Maximum
tapping length
: 5mm)

38.5

18.5
5

Outside Dimensions of Main Unit

163.4

ESC+-MENU

216.2
305

(IPC-DT/M61VT-DC1)

87.7
240

POWER

[mm]

11

3. Outside Dimensions and Part Names

IPC-DT/L61SVT-DC1

100

75

100

75

27.5

6.5

302

8-M4 TAP

(Maximum tapping
length : 5mm)

M3 TAP

(Maximum tapping

54.5

length : 5mm)

242

COM USBDVI VG A

212VDC-IN1

FG-+

CAUTION!

************

12VDC-IN*1*2***

Don't connect 1 and 2 of

12VDC-IN simultaneously.

21.5

41.5
5

Figure 3.3. Outside Dimensions of Main Unit (IPC-DT/L61SVT-DC1)

IPC-DT/H61XT-DC1

21

220
357

U

SB

75

100

DVI VGA

COM

41 5

288

233

189.5

ESC+-MENU

POWER

251
316

96.8
256

[mm]

123

305

ESC+-MENU

POWER

8-M4 TAP

(Maximum tapping
length : 5mm)

75

100

M3 TAP

(Maximum tapping
length : 5mm)

309
376

[mm]

Figure 3.4. Outside Dimensions of Main Unit (IPC-DT/H61XT-DC1)

User’s Manual

12

3. Outside Dimensions and Part Names

IPC-DT/M61VT-AC0

100

75

75

100

27.5

6.5

8-M4 TAP

(Maximum tapping
length : 5mm)

VGADVI USBCOMLN

226

39.3

67.4

291
148

67.5

49

8

38.5

18.5
5

216.2

Figure 3.5. Outside Dimensions of Main Unit (IPC-DT/M61VT-AC0)

IPC-DT/L61SVT-AC0

100

75

75

100

27.5

6.5

8-M4 TAP
(Maximum tapping

length : 5mm)

VGADVI USBCOM

242

NL

40.367.4

163.4

305

189.5

MENU-+ESC

87.7
240

POWER

[mm]

96.8
256

Figure 3.6.

User’s Manual

302
148

67.5

54.5

8

41.5

21.5
5

Outside Dimensions of Main Unit

- +

MENU

ESC

POWER

251
316

(IPC-DT/L61SVT-AC0)

[mm]

13

3. Outside Dimensions and Part Names

IPC-DT/H61XT-AC0

5

21

41

148
220
357

8

67.4
123

305

75

100

8-M4 TAP
(Maximum tapping
length : 5mm)

100

VGADVI USBCOM

LN

75

69.3

288

233

- +

MENU

ESC

POWER

309

376

[mm]

Figure 3.7. Outside Dimensions of Main Unit (IPC-DT/H61XT-AC0)

User’s Manual

14

3. Outside Dimensions and Part Names

Part Names

Right side

Front

MENU ESC

Screen adjustment switch

Back

XXXXXXXXX

XXXXXXXXXXXXXXXXXX

MODEL :
SERIAL No. : XXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXINPUT :

CAUTION!

The screw bolt ing torque
of attachment mus t be

0.6N-m(MAX).

Screen & Touch panel

+-

POWER

POWER LED

USBVGADVICOM

TI

CN

ES

P

PASS

XXXXXXXXX
XXXXXXXXX

1

2

12VDC-IN

+12VDC power connector

CAUTION!

Don't connect 1 and 2 of
12VDC-IN simultaneou sly.

12VDC-IN*1*2***
************

Left side

USB touch panel connector
Analog RGB connect o r

DVI-D connector

RS touch panel connector
AC adapter jack

Figure 3.8. Part Names(IPC-DT/S61VT -D C1 )

User’s Manual

15

3. Outside Dimensions and Part Names

Front

Screen & Touch panel

MENU-+ESC

POWER

Right side

Screen adjustment switch

Back

POWER LED

Left side

USB touch panel connector

VGADV USBCOM

Analog RGB con ne ctor
DVI-D connector

1

12VDC-IN

+

-

2

F

CAUTION!

************

12VDC-IN*1*2***

12VDC-IN simultaneo usly.

Don't c onnect 1 an d 2 of

RS touch panel connector
AC adapter jack

+12VDC power connector

Figure 3.9. Part Names(IPC-DT/M61VT-DC1, IPC-DT/L61SVT-DC1, IPC-DT/H61XT-DC1)

User’s Manual

16

3. Outside Dimensions and Part Names

Front

Screen & Touch panel

MENU-+ESC

POWER

Right side

Screen adjustment switch

Back

POWER LED

COM USBDV VGA

NL

Left side

USB touch panel connector
Analog RGB co n ne ctor

DVI-D connector

RS touch panel connector

AC power supply terminals

Figure 3.10. Part Na mes (IP C- DT/M 61 VT- AC0 , I PC -DT /L61 S VT -A C0, IP C-DT / H61 XT- AC0 )

User’s Manual

17

3. Outside Dimensions and Part Names

Analog RGB Connector

Table 3.1. Analog RGB Connector

Connector type

10

Pin NO.

1
2
3
4
5
6
7
8

15-pin HD-SUB (FEMALE)

5

15

Signal name

RED

GREEN

BLUE

N.C.

GND
R-GND
G-GND
B-GND

1

11

Pin NO.

9
10
11
12
13
14
15

6

Signal name

N.C.

GND

N.C.

DDC DATA

HSYNC

VSYNC

DDC CLK

RS Touch Panel Connector

This connector is RS-232C compliant to be used for touch panel data communication with the host
computer.

Table 3.2. RS Touch Panel Connector

Connector type

Pin NO.

1
2
3
4
5

User’s Manual

18

9-pin D-SUB (MALE)

1 5

6

Signal name

10K pull down

TxD
RxD

N.C.

GND

9

Pin NO.

6

7

8

9

Signal name

10K pull down

N.C.
10K pull down
10K pull down

3. Outside Dimensions and Part Names

USB Touch Panel Connector

The USB connector for communication between the host computer and touch panel.

Table 3.3. USB Touch Panel Connector

Connector type

Pin NO.

1
2

USB Type B (Receptacle)

21

43

Signal name

+5V

DATA-

Pin NO.

Signal name
3
4

DATA+

GND

User’s Manual

19

3. Outside Dimensions and Part Names

DVI-D Connector

Table 3.4. DVI-D Connect r o

Connector

DVI-I 24pin

9

1

17

8

16

24

Pin No. Si gnal name Pin No. Signal name

1

2

3

4 N.C. 16 HPD
5 N.C. 17

6 DDC CLK 18

7

8 N.C. 20 TXD
9

10

11

12 N.C. 24

TMDS

DATA2-

TMDS

DATA2+

TMDS

DATA2

SHIELD

DDC

DATA

TMDS

DATA1-

TMDS

DATA1+

TMDS

DATA1

SHIELD

13 N.C.

14 +5V

15 GND

TMDS

DATA0-

TMDS

DATA0+

TMDS

19

21 RXD

22

23

DATA0

SHIELD

TMDS

DATA0

SHIELD

TMDS

CLK+

TMDS

CLK-

User’s Manual

20

4. Hardware Setup

4. Hardware Setup
Installation Requirements

To maintain the ambient temperature within the installation environment requirement range, provide a
gap of 30mm or more between the main unit and any adjacent equipment.

Side view

30mm or more(back)

Panel

30mm or more(above)

30mm or more
(Bottom)

Bottom view

30mm or more(Side)

CAUTION!

Don't connect 1 and 2 of
12VDC-IN simultaneously.
12VDC-IN*1*2***
************

Interface surface

Panel

Figure 4.1. Distances Between Computer and Surroundings

Panel Cut

Cut the display mount panel in the following dimensions. The four corners of the solid-line rectangle
define the panel cut dimensions.

+1

199

-0

+1

-0

155

Panel thickness range: 1.6 to 7mm [mm]

Figure 4.2. IPC-DT/S61VT-DC1 Panel Cut Dimensions

User’s Manual

21

4. Hardware Setup

+1

292

-0

+1

-0

227

Panel thickness range: 1.6 to 7mm [mm]

Figure 4.3. IPC-DT/M61VT-DC1, IPC-DT/M61VT-AC0 Panel Cut Dimensions

+1

303

-0

R1 or less

+1

-0

243

Panel thicknes range: 1.6 to 7mm [ mm]

Figure 4.4. IPC-DT/L61SVT-DC1, IPC-DT/L61SVT-AC0 Panel Cut Dimensions

+1

358

-0

R1 or less

+1

-0

289

Panel thickness range: 1.6 - 7mm

[mm]

Figure 4.5. IPC-DT/H61XT-DC1, IPC-DT/H61XT-AC0 Panel Cut Dimensions

User’s Manual

22

4. Hardware Setup

Attaching the Fitting Used to Attach to the Main Unit

(1) Hold the main uni t f ro m the ou ts ide of th e pa nel .

Figure 4.6. Attaching the Fitting Used to Attach to the Main Unit < 1 / 2 >

(2) Hold the attach from the inside of the panel.

Metal fittin g s

Main body

Overtightening screws may result in damage.

Example of figure:IPC-DT/M61VT-xxx

Panel

Figure 4.6. Attaching the Fitting Used to Attach to the Main Uni < 2 / 2 >

User’s Manual

23

4. Hardware Setup

User’s Manual

24

5. Connection to the Host Computer

C

5.

Purchase individual connection cables as they are not bundled with this equ ipment.

onnection to the Host Computer

Analog RGB Connection

Connect the analog RGB in put on th is u nit to th e analog RGB connectors on the host computer.

Table 5.1. Recommendation Display Cable

Model Maker Cable length

KC-V2 SANWA SUPPLY INC. 2m
KC-V5 SANWA SUPPLY INC. 5m

If you use any other cable, select a shielded cable the wire carrying the RGB and H/Vsync si gnals and the
grounded wire in a twisted pair. Note that a non-twisted-pair cable may degrade image quality, in
particular, which is longer than 2 m.

Any loss of image quality due to use of a cable other than the recommende d cable or i ts equivale nt is not
covered by warranty.

User’s Manual

25

5. Connection to the Host Computer

DVI-D Connection

Connect the DVI-D input on this un it to th e DVI-D connector on the host computer or the PanelLink
connector. You can use a CONTEC IPC serie s or SBC (single board c omputer) as the host computer. In
this case, settings are required on each host computer.

Set the LCD type as follows depending on the host computer to be used.

When connecting to a SPI-6940-LLVA
To use this SBC board with the display, set the on-board switch (SW1) as shown below.

Table 5.2. SW1 Switch Settings

IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1

ON

IPC-DT/M61VT-AC0

ON

IPC-DT/L61SVT-D C 1
IPC-DT/L61SVT-AC0

ON

IPC-DT/H61XT-DC1
IPC-DT/H61XT-AC0

ON

1234

1234

1234

1234

CAUTION

Use this board along with the LCD signal conversion board [ADP-6940].

When connecting to a PC-686BX(PC)-LV
To use this SBC board with the display, set the on-board switch (U2) as shown below.

Table 5.3. U2 Switch Se tti ngs

IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1

ON

12345678

IPC-DT/M61VT-AC0

ON

12345678

IPC-DT/L61SVT-D C 1
IPC-DT/L61SVT-AC0

ON

12345678

IPC-DT/H61XT-DC1
IPC-DT/H61XT-AC0

ON

12345678

CAUTION

When using this board, also use an ISA bus type panel link I/F board (ADPLNK(PC)H).

User’s Manual

26

5. Connection to the Host Computer

When connecting to a PC-686E(PC)-LV
To use this SBC board wi th th e disp la y, se t th e on -boa rd rot ary s wit ch as shown be low .

Table 5.4. Rotary Switch Setting Number

IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1

IPC-DT/M61VT-AC0

2 2 0 1

IPC-DT/L61SVT-D C 1
IPC-DT/L61SVT-AC0

IPC-DT/H61XT-D C1
IPC-DT/H61XT-AC0

CAUTION

When using this board, also use an ISA bus type panel link I/F board (ADPLNK(PC)H).

When connecting to a PC-586U(PC)-LV, PC-586U(PC)-LVS
To use this SBC board with the display, set the on-board switch (S2) as shown below.

Table 5.5. S2 Switch S et tings

IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1

ON

IPC-DT/M61VT-AC0

ON

IPC-DT/L61SVT-D C 1
IPC-DT/L61SVT-AC0

ON

IPC-DT/H61XT-D C1
IPC-DT/H61XT-AC0

ON

1234

1234

1234

1234

CAUTION

When using this board, also use an LCD connector conversio n board (EXLCD68) or a n ISA bus type

panel link I/F board (ADPLNK(PC)H).

When connecting to a PC-586HU(PC)-LV
To use this SBC board with the display, set the on-board switch (J8) as shown below.

Table 5.6. J8 Switch Se tt ings

IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1

7
8

1
2

IPC-DT/M61VT-AC0

7
8

1
2

IPC-DT/L61SVT-D C 1
IPC-DT/L61SVT-AC0

7
8

* All is open.

1
2

IPC-DT/H61XT-D C1
IPC-DT/H61XT-AC0

7
8

1
2

CAUTION

When using this board, also use an ISA bus type panel link I/F board (ADPLNK(PC)H).

User’s Manual

27

5. Connection to the Host Computer

When connecting to a IPC-BX/M600(PCW) Series
If using this box computer , set the "Embe dded " - "C RT/ FPD" B IOS sett ing to "AU TO S elect " or "SW

Select". If you select "SW Select", set the switch (S1) on the box computer board as shown below.

Table 5.7. S1 Switch S et tings

IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1

ON

IPC-DT/M61VT-AC0

ON

IPC-DT/L61SVT-D C 1
IPC-DT/L61SVT-AC0

ON

IPC-DT/H61XT-DC1
IPC-DT/H61XT-AC0

ON

12345678

12345678

12345678

12345678

When connecting to a IPC-BX/M630(PCI) Series
No specific host settin gs a re requi re d if using th is box co mpu t er. How eve r, if usin g th e Windo ws XP

operating system, only connect the analog RGB cable during installation. Change t o the DVI connection
after installation completes.

When connecting to a IPC-BX/M360(PCI)C Series
When using this box computer, set the size of the connecting display by selecting “Advanced Chipset

Features Setup” – “Panel Type” in the BIOS setting section.
Example) For IPC-DT/L6xSVT-xx : “800 x 600”

CAUTION

If connecting this display to a product with the “AUTO Select” function such as

IPC-BX/M600(PCW) and IPC-BX/M360(PCI)C, or to a product with the “plug and play” function
such as the IPC-BX/M630(PCI) series, first connect cables, then turn on the display, always b ef ore
turning on the host computer. If the host computer is started before the display, it may not be able to
read the information on the disp lay, and as a result, no screen image may come up.

In this case (e.g. when the display is turned on afterward, when a cable is connected afterward),
specify the display size in the BIOS settings on the host computer.

User’s Manual

28

5. Connection to the Host Computer

Touch Panel Data Communications

These connections are used to send touch panel data to the host comput er via the USB or RS- 232C serial
port. Connect to the USB port or serial port (COM port) on the host computer.

Table 5.8. Example of a USB connection cable (USB Type A(Host) Û Type B(Display)cable)

Model Maker Cable length

KU20-2H
KU20-5H

Table 5.9. Option Cable (RS-232C Straight Cable)

Model Maker Cable length

IPC-CBL3-2 CONTEC 2m
IPC-CBL3-5 CONTEC 5m

CAUTION

- The RS-232C cable is not required if using the DVI-D input with a CONTEC host computer because
the DVI-D interface includes the RS-232C signal lines. Note that connecting the RS-232C cable
causes the touch panel to stop working.

- Touch panel driver software is required to use the touch panel. Purchase optional driver software
[IPC-SLIB-01 for windows or IPC-TPB1-DRV for MS-DOS] or download one from the CONTEC’s
web site.

- The USB touch panel driver software requires V1.40 or later of IPC-SLIB-01.

- The USB connection can only be used on Windows XP, 2000, or 98SE. Connect via the RS-232C
interface if using a different OS.

- Use either USB or RS-232C for connecting the touch panel. The touch panel cannot be connected
via both interfaces at the same time.

- When using the USB connection, the screen image may disappear momentarily when t he USB cabl e
is connected or disconnected and when the computer power is turned ON or OFF.

- When using the USB connection via a hub, the unit may not operate correctly in some cases
depending on the other USB devices connected to the hub. Please check the operation before using
in practice.

SANWA SUPPLY INC.
SANWA SUPPLY INC.

2m
5m

User’s Manual

29

5. Connection to the Host Computer

User’s Manual

30

6. Power Supply Connection

6. Power Supply Connection

Two versions of this product are available that use AC input and DC input respectively for the power
supply. The power supply connector consists of a terminal block on the AC input type and a power
supply connector and AC adapter jack on the DC input type.

CAUTION

- On the DC input type, input the power supply to the power supply connector only or the AC adapter
jack only. Never supply power to both of them at the same time as it can cause a fault.

- If you connect a power supply other than the option, be sure to take safety measures for the power
supply, such as overvoltage protection. Use meticulous care not to mistake the connection polarity
or voltage of the power supply as it may break the equipment, the power supply, or both.

AC input type

Table 6.1. Power Supply Connector

Connector type

Pin No. Signal name

1 FG(Frame Gnd)
2 N
3 L

AC Input Terminals

23

1

N

- Screw diameter: M3.5, Terminal pitch: 9.5mm

- Terminal type

L

7.8

3.9

6.2

Note: This product does not have an AC on/off switch.

User’s Manual

31

6. Power Supply Connection

DC input type

Power Supply Connector

When connecting the power sup ply , en su re th at th e su ppl y sati sf ies the spec ifica tion s bel ow .

- Power supply voltage: +12VDC 5%

- Power supply capacity: 2.5A or more
The table below lists the pin specifications of the power connector on the back of the equipment.

Table 6.2. Power Supply Connector (IPC-DT/S61VT-DC1)

Connector type

Model

Pin No.

+12 VDC input connec to r
B4PS-VH(manufactured by JST)

Signal name
1
2
3
4

4321

GND

GND
+12V
+12V

* Please obtain your own connector for the cable.

Applicable power cable connector

Housing: VHR-4N (manufactured by JST)
Contact: SVH-21T-1.1(A WG22-18)

(manufactured by JST)

Table 6.3. Power Supply Connector (IPC-DT/M61VT-DC1, IPC-DT/L61SVT-DC1,
IPC-DT/H61XT-DC1)

Connector

type

Model DFK-MC1,5/3-GF-3,81

Pin No. Signal name

1 FG(Frame Gnd)
2 GND
3 +12V

+12VDC input connector

(PHOENIX CONTACT)
1 2 3

* Use the supplied MC1,5/3-STF-3,81 for the cable connector.

User’s Manual

32

6. Power Supply Connection

AC Adapter Jack

The AC adapter jack is used to connect the AC adapter [IPC-ACAP12-01] available as an option. Do not
connect any AC adapter other than the option.

+12V

GND

Figure 6.1. AC Adapter Jack

User’s Manual

33

6. Power Supply Connection

AC adapter code removal prevention fitting

(1) Insert th e pl ug of AC Ad ap te r.
(2) Tighten the screws on the attachment fitting.

Figure 6.2. Code Removal Prevention Fitting

User’s Manual

34

7. Screen Adjustment and a Setup

7. Screen Adjustment and a Setup

The equipment has s cr een ad jus t ment s wi tch es [ ME NU ], [ +] , and [-] . U se th e se s w itch e s to ad ju s t the
screen. (For the locations of the switches, see “Part Names” in Chapter 3.) When using the equipment
for the first time or after changing the output screen mode of the host computer, execute AUTO ADJUST
first on the menu screen. Use these switches also to adjust the screen brightness and contrast and to make
settings for the touch panel.

Menu Screen

Pressing the [MENU] switch displays the main menu screen. Use the [+] and [-] switches to select
individual items, adjust them, then press the [MENU] to save the settings.

SCREEN MANAGER

BRIGHTNESS
CONTRAST
DISPLAY ADJUST

R

G B

COLOR CONTROL

Othe

r

OTHERS
TOUCH PANEL

INPUT SOURCE
RESET

640x480 60.0Hz

Analog RGB input DVI-D input

Figure 7.1. Main Menu Screen
BRIGHTNESS:

Select this item to adj ust the brightness of the backlight. Press [+] or [-] to optimize

the item. The brightness can also be adjusted by pressing the [+] and [-] keys
without the MENU screen displayed, as the direct brightness control keys.

CONTRAST:

Select this item to adjust the contrast of the screen. Press [+] or [-] to optim ize the

item.

SCREEN MANAGER

BRIGHTNESS
V.POSITION SP

Othe

r

OTHERS
TOUCH PANEL
INPUT SOURCE
RESET

640x480 60.0Hz

User’s Manual

35

7. Screen Adjustment and a Setup

DISPLAY ADJUST

: Adjusts the display position. Selecting this item displays a sub-menu. Use [+]

and [-] to move between items and [MENU] to select.

SCREEN MANAGER

H.POSITION
V.POSITION
V.POSITION SP

WIDTH

A

A

PHASE
AUTO SETUP

HORIZONTAL POSITION

640x480 60.0Hz

Figure 7.2. DISPLAY ADJUST Sub-Menu Screen

H.POSITION: Select this item to adjust the horizontal position of the screen. Press [+] or [-]

while checking the screen to optimize the item.

V.POSITION: Select this item to adjust the vertical position of the screen. Press [+] or [-]

while checking the screen to optimize the item.

V.POSITION SP: Adjusts the position vertically. Use this item if the screen is offset or flickers

WIDTH: Select this item to adjust the horizontal display size of the screen. Press [+] or

PHASE: Adjust this item when the screen is partlyb lurred or flickering. Press [+] or [-]

AUTO SETUP: Select AUTO ADJUST when using the equipment for the first time or when the

CAUTION

AUTO ADJUST may fail to adjust the screen correctly depending on the host computer or th e

display screen (mostly black screen such as in t he DOS text mode). I n such a case, adjust POSITION
and WIDTH to manually optimize the screen.

after using "AUTO SETUP" despite adjusting with "V.POSITION". Press [+]
or [-] while checking the screen to optimize the position.

[-] to optimize the item.

while checking the screen to optimize the item.

screen cannot be displayed normally due to a change made to the display mode.
Select this item and press [MENU] to accept y our se lect ion, and t he eq uipment
starts performing automatic adjustment.

User’s Manual

36

7. Screen Adjustment and a Setup

COLOR CONTROL:

Adjusts the color temperature. Selecting this item displays a sub-menu. Use
[+] and [-] to move betwee n item s and [ME NU] to select . You can select USER
COLOR MODE to adjust RED, GREEN, and BLUE manually.

SCREEN MANAGER

R

G B

R

G B

R

G B

R

G B

COLOR TEMPERATURE

640x480 60.0Hz

Figure 7.3. COLOR CONTROL Sub-Menu Screen

OTHERS:

K

9300
6500

K
K

5000

USER COLOR MODE

The display position and time etc. of the OSD screen can be adjusted. Selecting
this item displays a sub-menu. Use [+] and [-] to move between items and
[MENU] to select.

Figure 7.4. OTHERS Sub-Menu Screen

OSD H.POSITION: Adjusts the horizontal position of the OSD. Press the [+] or [-] while viewing

the screen to adjust the position.

OSD V.POSITION: Adjusts the vertical position of the OSD. Press the [+] or [-] while viewing

the screen to adjust the position.
OSD TIMER: Adjusts the dis pla y ti me for th e OSD . Us e [ +] and [-] to adju st the ti me .
SILENT MODE: SILENT MODE controls display message “No Input Signal" and “Power

Saving" of DISPLAY when it is effective.
INFORMATION: Information on the input signal and version information on OSD are

displayed.

User’s Manual

37

7. Screen Adjustment and a Setup

TOUCHPANEL:

Select this item to adjust the status of the touch panel. Select this item to invoke the

submenu, select a desired item using [+] or [-], then press [MENU] to accept the
setting made.

SCREEN MANAGER

ON/OFF

I D

DISPLAY ID
INTERVAL

Mode

MODE
BEEP

TOUCH PANEL ON/OFF

640x480 60.0Hz

Figure 7.5. TOUCH PANEL sub menu

ON/OFF: Select this item to turn ON (enable) or OFF (disable) the touch panel operation.

(The equipment is started always with this item set to OFF.) Usually, this item does
not have to be set as the touch panel is turned ON (enabled) automatically upon
startup of the touch panel driver. Note, however, that the touch panel does not
work when the equipment is connected to the host with the touch panel driver
already up and running or when the power to the equipment is recycled. In
suchcases, set this item to ON (enabled).

DISPLAY ID: Set the ID to use for USB multi-touch panel operation. See Chapter 9 for details of

USB multi-touch panel operation. (Factory setting: 6)

INTERVAL: Select this item to adjust the scan timing of the touch panel. Press [+] or [-] to

increase or decrease the response of the touch panel. (Factory setting: 5)

MODE: Select the touch panel mode (WINDOWS or DOS) depending on the host OS. For

use in the MS-DOS environment (using the MS-DOS touch panel driver), be sure
to set this item to “DOS”. (Factory setting: WINDOWS)

BEEP: Select this item to turn on or off the click t one of the t ouch pane l. (Fac tory se tting:

OFF)
When using the touch panel driver for Windows, the settings specified in the touch
panel driver are used instead.

User’s Manual

38

7. Screen Adjustment and a Setup

INPUT SOURCE:

Selects the input signal. Selecting this item displays a sub-menu. Use [+] and [-]
to move between items and [MENU] to select.

SCREEN MANAGER

ANALOG RGB

DVI

ANALOG RGB

640x480 60.0Hz

Figure 7.6. INPUT SOURCE Sub-Menu Screen

ANALOG RGB: Displays the input from the ANALOG RGB connector.
DVI: Displays the input from the DVI connector.

Restores all settings to their factory defaults. Use this option to initialize the

RESET:

settings if the screen display is lost or does not work correctly. You can also reset
the settings by holding down the [MENU] direct key when tuning on the power.

User’s Manual

39

7. Screen Adjustment and a Setup

Direct Key

CONTRAST : Pressing the [+] key when the menu is not displayed opens the contrast

BRIGHTNESS : The brightness of the backlight can be adjusted by pressing the [+] and [-] keys

RESET : All the settings can be reset to the factor y defaults by turning on t he equipment

Power save mode : You can place the equipment in the power save m ode by depre ssing both of the

* Recycling the power to the equipment in the power save mode recovers it to the normal display state.
* The POWER LED on the front face remains blinking in green in the power save mode.

Memory of a Setting Value

The equipment retains its settings even when the power is tur ned of f. Note, howe ver, t hat the foll owing
settings are reset to their defaults without being retained.

- The power save mode setting made by the direct key is reset to the normal state when the power is
turned on.

- The TOUCH PANEL ON/OFF setting is set to OFF when the power is turned on.

adjustment sc r e en.

without the menu screen displayed.

while holding down the [ME NU ] ke y.

[+] and [-] keys at the same time without the menu screen displayed. This can
force the screen display and backlight to be turned off. Release the buttons
when “POWER SAVE MODE…” appears on the screen. You can recover the
screen from the power save mode by pressing any of the front switches. The
power consumption of the equipment in the power sav e mode is about 1/5 of
that during normal operation. Turning off the backlight when not requ ired th e
backlight to extend its life.

User’s Manual

40

8. LED Indicators

8. LED Indicators

The POWER LED on the front face indicates each state of the display as follows:

Table 8.1. LED Indicators

LED status Description
OFF The power supply off or the equipment not started normally
Green(ON) Normal operation

Green
(Flashing)

Orange (ON) Unsupported signal input *1

Orange
(Flashing)

*1 The LED looks like this when the equipment cannot process the input

*2 The LED looks like this also when the horizontal or vertical sync

Power save mode

No signal input *2

signal to provide normal display, for example, when the
horizontal/vertical sync signal frequency is exceeding the supported
frequency. See Chapter 9 "Display mode" fo r the di splay mode s
supported by this equi pm ent .

signal is turned of f b y t h e pow e r ma nag e me nt fun ction of the host
computer. The equipment enter s the p owe r save mode a utoma ti call y
when no signal has been input for about two seconds.

User’s Manual

41

8. LED Indicators

User’s Manual

42

9. Touch Panel

9. Touch Panel

This equipment has a touch panel that enables keyboard-less, mouse-less operations by communication
with the host computer using the RS-232C cable.

Touch panel

MENU ESC

+-

POWER

Host PC Touch panel controller Touch panel

CPU

Communicatio n controller

INT

Serial

communication

CPU

Figure 9.1. Touch Panel and Block Diagram

Data input at the touch panel is processed by the tou ch panel contr oller and pa ssed to the host PC via the
serial port on the CPU in the controller.

Before the touch panel can be used, touch panel driver software must be installed. Note that the driver
software is not bundled with this product. Purchase the one separately or download it from the
CONTEC’s web site.

For further details, refer to the READ_ME file for each driver.

<Option touch panel driver>

Windows XP/2000/NT 4.0/98SE/95OSR2 : IPC-SLIB-01
MS-DOS 6.2 : IPC-TPB1-DRV

CAUTION

- The USB touch panel driver software requires V1.40 or later of IPC-SLIB-01.

- The USB connection can only be used on Windows XP, 2000, or 98SE. Connect via the RS-232C
interface if using a different OS.

- Use either USB or RS-232C for connecting the touch panel. The touch panel cannot be connected
via both interfaces at the same time.

- When using the USB connection, the screen image may disappear momentarily when t he USB cabl e
is connected or disconnected and when the computer power is turned ON or OFF.

User’s Manual

43

9. Touch Panel

USB Multi-Touch Panel

This function can be used in the case when t he RGB signal from the host computer is split for connecting
to multiple displays via a splitter. The function permits touch panel operation to be used at all the
displays. A maximum of eight touch panel displays can be connected.

Note that all touch panels must be connected via USB and, to allow the touch panel driver software on
the host computer to identify each device, a different USB ID must be set on the DIP switch located on
the side of each display unit.

USB ID7

RGB cable

USB cable

MENU ESC

+-

POWER

USB ID0

MENU ESC

+-

POWER

Touch panel display

8 sets(Max.)

Host PC

RGB distributor

USB HUB

Figure 9.2. Example of connection of a USB multi-touch panel

You can use a CONTEC IPC-PT/600 series panel computer as the host PC.
In this case, the ID of the touch panel in the panel computer is fixed at ID7. Set the IDs of the external
displays in the range USB ID0 - USB ID6 (a maximum of seven external displays can be connected).

CAUTION

You cannot use multiple touch panels via the RS-232C interface.

User’s Manual

44

10. Display Mode

10. Display Mode

This equipment supports the following display modes:

Table 10.1. Analog RGB Input - Display Modes

Display

Video

Number of
pixels (dot)

mode

VGA 640 x 350 25.18 31.47 70 Ο Ο Ο Ο
VGA 720 x 400 28.32 31.47 70 Ο Ο Δ Ο

VGA 640 x 480 25.18 31.47 60 O O
VESA 640 x 480 31.50 37.86 72 Ο Ο Ο Ο
VESA 640 x 480 31.50 37.50 75 Ο Ο Ο Ο
VESA 800 x 600 36.00 35.16 56 Ο Ο Ο Ο
VESA 800 x 600 40.00 37.88 60 Ο Ο Ο
VESA 800 x 600 50.00 48.08 72 Ο Ο Ο Ο
VESA 800 x 600 49.50 46.88 75 Ο Ο Ο Ο
VESA 1024 x 768 65.00 48.36 60 Ο Ο Ο
VESA 1024 x 768 75.00 56.48 70 Ο Ο Ο Ο
VESA 1024 x 768 78.75 60.02 75 Ο Ο Ο Ο
VESA 1280 x 1024 108.00 63.98 60 Ο Ο Ο Ο
VESA 1280 x 1024 135.00 79.98 75 Ο Ο Ο Ο

Δ: Display availabl e but qu ality i s reduce d
Ο: Display available
: Recommended resolution (mode)

Dot clock

(MHz)

Horizontal

frequency

(kHz)

Vertical

frequency

(Hz)

IPC-DT/S61VT-DC1

IPC-DT/M61VT-DC1,

IPC-DT/M61VT-AC0

IPC-DT/L61SVT-DC1,

IPC-DT/L61SVT-AC0

IPC-DT/H61XT-DC1,

IPC-DT/H61XT-AC0

Table 10.2. DVI-D Input - Display Modes

Display

Video

mode

Number of
pixels (dot)

Dot clock

(MHz)

Horizontal

frequency

(kHz)

Vertical

frequency

(Hz)

IPC-DT/S61VT-DC1

IPC-DT/M61VT-DC1,

IPC-DT/M61VT-AC0

IPC-DT/L61SVT-DC1,

IPC-DT/L61SVT-AC0

IPC-DT/H61XT-DC1,

VGA 640 x 480 25.18 31.47 60 Ο Ο
VESA 800 x 600 40.00 37.88 60 x x Ο
VESA 1024 x 768 65.00 48.36 60 x x x

x: Display unavailable

Ο: Display available

: Display available Recommended resolution (mode)

User’s Manual

IPC-DT/H61XT-AC0

45

10. Display Mode

CAUTION

- The number of display pixels in the LCD is 640 x 480 dots on the IPC-DT/S61VT-DC1,
IPC-DT/M61VT-DC1, and IPC-DT/M61VT-AC0 models, 800 x 600 dots on the
IPC-DT/L61SVT-DC1 and IPC-DT/L61SVT-AC0 models and 1024 x 768 on the
IPC-DT/H61XT-DC1 and IPC-DT/H61XT-AC0 models. The display is automatically enlarged if
the input resolution is less than the LCD size and reduced if larger than the LCD size. Note that, as
a result of enlarging or reducing the display size, the displayed image will not be as clear as when the
resolution matches the LCD display size.

- The screen will not display correctly if the resolution and frequency do not match one of the
supported display modes.

User’s Manual

46

11. Options

11. Options

Screen protective sheets

- IPC-CV6 : 6.4-inch screen protective sheets (10 sheets)

- IPC-CV : 10-inch screen protective sheets (10 sheets)

- IPC-CV12 : 12.1-inch screen protective sheets (10 sheets)

- IPC-CV15 : 15-inch screen protective sheets (10 sheets)

Cable

- IPC-DVI/D-020 : DVI-D cable (2m)

- IPC-DVI/D-050 : DVI-D cable (5m)

- IPC-PLDVI-020 : Panel link - DVI-D conversion cable (2m)

- IPC-PLDVI-050 : Panel link - DVI-D conversion cable (5m)

- IPC-CBL3-2 : Touch panel, COM cable (2m)

- IPC-CBL3-5 : Touch panel, COM cable (5m)

Driver

- IPC-SLIB-01 : Driver & Utility Soft Set (CD-ROM version)

Others

- IPC-ACCODE3 : AC power cable (2m, 125VAC)

- IPC-ACAP12-01 : +12 VDC output AC adapter
Input: Voltage = 90 - 264V AC, Current =1.3A (Typ.)
(for input voltage = 100V AC)
Output: Voltage = 12V DC, Current = 3.5A

- IPC-SND-03 : Desk stand

Recommendation Cable (Maker: SANWA SUPPLY INC.)

- KC-V2 : RGB display cable (2m)

- KC-V5 : RGB display cable (5m)

- KU20-2H : USB cable for touch panel (2m)

- KU20-5H : USB cable for touch panel (5m)

User’s Manual

47

IPC-DT/61 Series

User’s Manual

IPC-DT/61-HME

CONTEC CO.,LTD. September 2007 Edition

3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Japanese http://www.contec.co.jp/
English http://www.contec.com/
Chinese http://www.contec.com.cn/

No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD. [09142007]

[04202004] Management No. A-46-795
[09142007_rev7] Part No. LYDA564