Page 1
IPC-PT/SV10DC1-4E
HPC-HSV10DC1-E
Hardware Manual
CONTEC CO.,LTD.
Page 2
Copyright
Copyright 2004 CONTEC CO., LTD. ALL RIGHTS RESERVED.
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this
document.
The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify
CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document or for results obtained by the user as a result of using this product.
Trademarks
MS, Microsoft and Windows are trademarks of Microsoft Corporation. Other brand and product
names are trademarks of their respective holder.
Hardware Manual
i
Page 3
Table of Contents
Copyright ................................................................................................................................................. i
Trademarks .............................................................................................................................................. i
Table of Contents.................................................................................................................................... ii
1. INTRODUCTION 1
Features.............................................................................................................................................1
Customer Support....................................................................................................................................2
Web Site............................................................................................................................................2
Limited One -Year Warran ty ...................................................................................................................2
How to Obtai n Service ............................................................................................................................2
Liability....................................................................................................................................................2
Safety Precautions ...................................................................................................................................3
Safety Inf ormation............................................................................................................................3
Handling Precautions .......................................................................................................................3
2. OVERVIEW 7
Specifications...........................................................................................................................................7
External D imensions .............................................................................................................................10
3. EACH COMPONENT FUNCTION 11
Component Locations ....................................................................................................................11
Serial Port Interface (COM1, COM2)...........................................................................................13
Ethernet ( UTP) ...............................................................................................................................14
PCMCIA (PC M CIA) ......................................................................................................................15
USB port (USB) .............................................................................................................................15
General-purpose I/O ports (I/O) ................................................................................................ ....16
AC adapter jack ..............................................................................................................................19
Power supp l y input connector........................................................................................................19
External Speaker Outpu t Terminal ( SPK).....................................................................................20
Touch Panel....................................................................................................................................20
DIP-Switch setting .........................................................................................................................21
LED display....................................................................................................................................22
4. HARDWARE SETUP 23
Installation Requirements...............................................................................................................23
Card removal prevention fitting.....................................................................................................23
Back light exchange .......................................................................................................................24
Attaching the Fitting Used to Attach to the Main Unit.................................................................24
Removing the cover for O S operation s etup DIP switch (SW2) ..................................................25
AC adapter r emoval prevention fitti ng..........................................................................................26
Hardware Manual
ii
Page 4
5. LIST OF OPTIONS 27
Hardware Manual
iii
Page 5
Hardware Manual
iv
Page 6
1. Introduction
1. Introduction
This product is a panel mount computer based on the SH-4 CPU, integrating a TFT color LCD display
with a touch screen. As the unit has assorted interfaces including the USB, PC Card, 100BASE-TX,
and RS-232C connectors, it can be used widely as a general-purpose terminal for embedded
applications.
Under Windows CE .NET 4.2 loaded from Flash ROM along with user programs, the unit is
implemented as diskless hardware without the need for a shutdown procedure.
A full line of models is available to support any power supply environment.
The product employs an aluminum front panel, resulting in shorter outside dimensions and lighter
weight than the conventional model. It also employs a simplified structure that makes installation
easier than the conventional model.
Features
- Slim, compact design with a lightweight aluminum front panel
(Embedded portion 60mm)
- LCD arm (VESA compliant 75mm type) available for installation
- 128MB(SDRAM) system memory standard
- 128MB of internal, erasable programmable Flash ROM available as a user area, allowing user
programs to be added and deleted.
Equipped with serial ports (2ch), USB ports (2ch), PC card slots, 100BASE-TX, general
-
purpose I/O, stereo sound function as standard. Installed supporting I/F drivers as
standard.
- XIP & memory loading boot function enabling quick startup in shortest about 10 seconds.
- Installed "CONTEC Manager" for system development support
- IP65/NEMA4 compliant front panel.
- Rear fitting to easily fix the unit in the installation hole
(such as scheduling, FTP server, autorun).
Hardware Manual
1
Page 7
1 Introduction
Customer Support
CONTEC provides the following support services for you to use CONTEC products more efficiently
and comfortably.
Web Site
Japanese http://www.contec.co.jp/
English http://www.contec.com/
Chinese http://www.contec.com.cn/
Latest product information
CONTEC provides up-to-date information on products.
CONTEC also provides product manuals and various technical documents in the PDF.
Free download
You can download updated driver software and differential files as well as sample programs available in
several languages.
Note! For product information
Contact your retailer if you have any technical question about a CONTEC product or need its price,
delivery time, or estimate information.
Limited One-Year Warranty
CONTEC products are warranted by CONTEC CO., LTD. to be free from defects in material and
workmanship for up to one year from the date of purchase by the original purchaser.
Repair will be free of charge only when this device is returned freight prepaid with a copy of the
original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office,
from which it was purchased.
This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and
original products. The warranty is not applicable if the device has been tampered with or damaged
through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in
which case repairs will be considered beyond the warranty policy.
How to Obtain Service
For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please
obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you
purchased before returning any product.
* No product will be accepted by the CONTEC group without the RMA number.
Liability
The obligation of the warrantor is solely to repair or replace the product. In no event will the
warrantor be liable for any incidental or consequential damages due to such defect or consequences that
arise from Safety Precautions.
Understand the following definitions and precautions to use the product safely.
Hardware Manual
2
Page 8
1. Introduction
Safety Precautions
Understand the following definitions and precautions to use the product safely.
Safety Information
This document provides safety information using the following symbols to prevent accidents resulting
in injury or death and the destruction of equipment and resources. Understand the meanings of these
labels to operate the equipment safely.
DANGER
WAR NI NG
CAUTION
DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury or in property damage.
Handling Precautions
WA RN IN G
Indicates that are assumed to result in possible death or serious injury if they are inappropriately
handled ignoring this icon.
- Do not use this product in the presence of flammable or corrosive gases. This may lead to explosion,
fire, or damage to equipment.
- In the event of smoke, or abnormal smells or sounds, immediately turn OFF the power to this
device, disconnect the plug from the power outlet, and contact the manufacturer. Continued use
could lead to fire or electrical shock.
- Because of the danger of electrical shock or fire, do not contact this device(Other than the front
touch panel) while electrical current is present.
- Never touch this device or connectors with wet hands. This can cause electrical shock.
- Do not allow this device to come into contact with foreign substances (metal particles, flammable
substances, liquids, etc.) This can cause fire or electrical shock.
- Do not place this device in an unstable location or use incomplete mountings. This may cause the
device to fall.
- This device must be operated at the specified voltage. Use of any other voltage level may cause fire
or electrical shock.
- This device must be properly grounded.
- When attaching or removing expansion units, always be sure to unplug the power cable from the
electrical outlet.
- Users should never disassemble or modify this device, or exchange components. This can cause fire
or electrical shock. In addition, the manufacturer is unable to repair products that have been
modified by the user.
- Procedures that could result in serious injury or loss of human life should never be performed from
a touch panel. Use system design methods that can guard against input errors.
Hardware Manual
3
Page 9
1 Introduction
- This product is not intended for use in aerospace, space, nuclear power, medical equipment, or other
applications that require a very high level of reliability. Do not use the product in such
applications.
- If you utilize this product in such usages where high reliability and safety are required as on the
trains, vessels, automotives or crime- or disaster-prevention devices, contact your retailer.
CAUTION
Take the following precautions when handling this product.
- Do not use or store the product in a location such as extremely high or low temperature, rapid
temperature changes, and the place which receives a strong ultraviolet ray.
Example: - Exposure to direct sun
- In the vicinity of a heat source
- Do not use the product in extremely humid or dusty locations.
It is extremely dangerous to use the product with its interior penetrated by water or any other fluid
or conductive dust. If the product must be used in such an environment, install it on a dust-proof
control panel, for example.
- Avoid using or storing the device in locations subject to shock or vibration.
- Do not use the product in the vicinity of devices that generate strong magnetic force or noise.
Such devices will cause this device to malfunction.
- Do not use or store the product in the presence of chemicals.
- To clean the PANECON-PC, wipe it gently with a soft cloth dampened with either water or mild
detergent. Do not use chemicals or a volatile solvent, such as benzene or thinner, to prevent
pealing or discoloration of the paint.
- Do not use any sharp-pointed object such as a mechanical pencil to touch the touch panel. Doing
so may scratch the touch panel, resulting in malfunctions.
- Do not subject the touch panel to shock as doing so may break it.
- When the surface or frame of the touch panel has become dirty, wipe it with neutral detergent. Do
not wipe the touch panel with thinner, alcohol, ammonia, or a strong chlorinated solvent. Use a
protective sheet (available as an option) if the touch panel is used where it can easily collect dust
and dirt.
- It is a characteristic of analog touch panels that their resistance may vary with changes to the
ambient environment (temperature and humidity) and with their own aging, resulting in the
deviation of the detection point. If this is the case, calibrate the touch panel again to re-set
calibration data.
- Burn-in on TFT Display
"Burn-in" may occur if the same display is retained for a long time. Avoid this by periodically
switching the display so that the same display is not maintained for a long time.
* Burn-In: Phenomenon characterized by a TFT display as a result of long-time display of the
same screen where a shadow-like trace persists because electric charge remains in the
LCD element even after the patterns are changed.
Hardware Manual
4
Page 10
1. Introduction
- Life expectancy of components
(1)Battery: A lithium-ion primary battery is used to back up the internal clock/calendar and CMOS
RAM. The non-energized backup time at 25°C is 10 years or more.
(2)LCD backlight: Display brightness decreases over time with use.
The operating lifetime of the backlight is 50,000 hours (the time until the
brightness is lowered to 50% of the initial value)
(3)Touch panel: The operating lifetime of the touch panel is at least 1 million touches (as tested
by mechanical touching under 300 g of force at a rate of two presses per
second).
(4)Flash memory (NFDISK): The number of times of rewriting has restriction that is more th an
300,000. (When the write size is 128KB or less.)
Since CF-CARD is used for Flash memory (NFDISK), When use is
carried out for the use that rewrites frequently, be careful of the
number of times of rewriting.
Moreover, when power supply OFF is done while writing it, data in
flash memory (NFDISK) might be damaged.
* CONTEC accepts your request for replacing each consumable in the PANECON-PC as a request
for repair (at an additional cost).
- If installed horizontally (with the LCD panel face up), the unit should be used at an ambient
operating temperature of not greater than 30 degrees centigrade.
- Be sure to turn off the power before plugging or unplugging any expansion board or connector.
- CONTEC reserves the right to refuse to service a product modified by the user.
- In the event of an abnormal condition or malfunction, please consult the dealer from whom the
equipment was purchased.
- Use an AC cable that is compatible with both the rated supply voltage and the receptacle.
- To connect with peripherals, use a grounded, shielded cable.
- This product contains a lithium battery as the primary cell and a cold cathode tube for the backlight.
When disposing of the product, therefore, treat it in accordance with the disposal regulations
stipulated by your local government.
Hardware Manual
5
Page 11
1 Introduction
Hardware Manual
6
Page 12
2. Overview
2. Overview
Specifications
Functional Specifications
Table 2.1. Functional Specifications
Type IPC-PT/SV10DC1-4E
LCD type 6.5-inch TFT color LCD (640 x 480) LCD type
Number of colors 65536
Resolution 4096 x 4096 (emulated in 640 x 480 mode) Touch panel
Detection method Analog resistive
CPU
Memory
COM port RS-232C(2ch)
RTC Benchmarq bq3287AMT Error tolerance ± 1 minute/month
LAN 10BASE-T/100BASE-TX 1ch, NS DP83816A
PC card slots PCMCIA Type II x 2 or TypeIII x 1
General-purpose I/O Photocoupler insulated inputs and outputs: 4 channels each
USB 2ch (USB 1.1)
Output terminals for external
speakers
DIP-SW DIP-SW input opened to user (4 bits)
LED The same function with POWER LED (Front Power LED: 3-color display)
Front function switch Front switch input: 4 points;
Front Power LED 3-color display
Input power supply
Outside dimensions (mm) 210(W) x 65(D) x 166(H)
Panel cut dimensions (mm) 199(W) x 155(H)
Weight About 1.5kg *1
*1 Does not include cables, optional accessories, and screws, etc.
Type SH-4 HD6417751RBP 240MHz
Internal cache Data: 16KB, Instruction: 32KB
Clock frequency 240MHz
Flash memory
(NFDISK)
System memory 128MB SDRAM
OS loading
Flash memory
128MB
32MB
COM1(16550, 9-pin D-SUB)
COM2(16550, 9-pin D-SUB)
Baud rate : 50 - 115200bps
φ3.5 Stereo mini jack Full-scale output level 1.0Vrms(Typ.)
USER LED (LED opened to user: 3-color display)
+12VDC
Input range: 12V±5% 2.5A(Max.)
Hardware Manual
7
Page 13
2 Overview
Installation Environment Requirements
Table 2.2. Installation Environment Requirements
Item Specification
Ambient specifications
Operating temperature 0 - 50ºC
Storage temperature -10 - 60ºC
Operating Humidity 20 - 85%RH(no condensation)
Floating dust particles Not to be excessive
Corrosive gases None
Line-noise
resistance
Vibration
resistance
Impact resistance
Ground Class D grounding (previous class 3 grounding)
Water-proof and dust-proof IP65, front
Line noise
Static
electricity
resistance
Anti-shaking
AC line: 2kV (Using the AC adapter IPC-ACAP12-01)
Signal line: 1kV (EN61000-4-4 Level3, IEC1000-4-4 Level 3)
Contact discharge / 4kV (EN61000-4-2 Level 2, IEC1000-4-2 Level 2)
Atmospheric discharge / 8kV (EN61000-4-2 Level 3, IEC1000-4-2 Level 3)
10 - 57Hz/semi-amplitude 0.15mm
One cycle (10-150-10 Hz) of 1 oct/min test at 19.6 m/s2 (2G) between 57 an
150 Hz x 10 times in three (X/Y/Z) directions (80 minutes each)
(JIS C0040-compliant, IEC60068-2-6-compliant)
Tested with 11-ms half-sine wave at 98 m/s2 (10G) three times in each of
three (X/Y/Z) directions
(JIS C0041-compliant, IEC60068-2-27-compliant)
Power Up Specification for DC Powered Models
Vol t
11.4 V
Hardware Manual
8
1 - 30mS
Time
Page 14
2. Overview
Display Optical Specifications
Table 2.3. IPC-PT/SV10 series
Parameter Condition Min. Typ.
View angle
(Vertical)
View angle
(Horizontal)
Contrast Display. Monochrome 150 250
Brightness
(at center)
φ = 180° 30deg 35deg
φ = 0° 40deg 45deg
CR⊇10
φ = +90° 45deg 50deg
φ= -90°
Display. White 250cd/m
Display.
Monochrome
45deg 50deg
2
300cd/m
2
Contrast ratio (CR) =
Left
( φ =
-
90o )
Brightness at screen center with white displayed
Brightness at screen center with black displayed
Measurement direction
Z
o
( θ = 0
)
θ
Top
o
( φ = 180
)
X
Bottom
( φ = 0
φ
o
)
Y
Module
Right
( φ = 90
o
)
Figure 2.1. Definition of viewable range
CAUTION
The above optical specification data shows optical characteristics of the liquid crystal in the display;
the data does not represent the actual view on the display or its viewing angles.
Hardware Manual
9
Page 15
2 Overview
External Dimensions
27
75
75
198
4-M4 TAP
(Maximum tapping length: 5mm)
(Maximum tapping length: 5mm)
50
154
M3 TAP
ACTLNK
PWR
USER
UTP
I/O
USB RST
105
COM1 COM2
SPK
PCMCIA
2341
SW1
ON*
FG
V+
V-
12VDC-IN
***
****
**
*
138
210
58
166
Figure 2.2. External Dimensions
60
16
5
[mm]
Hardware Manual
10
Page 16
3. Each Component Function
3. Each Component Function
Component Locations
CF card (NFDISK) cover
***
****
**
*
LAN
Function switch
DIP-SW(SW2) cover
POWER LED
USER LED
POWER LED
RESET
USB
PCMCIA
I/O
COM2
PWR
USER
UTP
RSTUSB
LNK A CT
I/O
COM2COM1
COM1
DIP-SW(SW1)
SPERKER
+12VDC power connector
AC adapter jack
* Refer to the software manual for the function switches, POWER LED and
Figure 3.1. Component Locations
Hardware Manual
SPK
PCMCIA
SW1
1432
ON*
V-
V+
FG
12VDC-IN
USER LED.
11
Page 17
3 Each Component Function
Table 3.1. Component Identification
Component Function
Function switch Refer to the software manual.
POWER LED Power supply ON display LED
USER LED USER LED (3-colors, opened to user)
+12VDC power connector +12V power supply input (3P phoenix contact)
AC adapter jack +12V power supply input (AC adapter: for IPC-ACAP12-01)
PCMCIA PCMCIA card slot
I/O Insulated I/O connector
SPEAKER Output terminals for external speakers
RESET Hard reset push button
USB USB port connector (2ch)
LAN Ethernet connector (RJ-45)
COM1 Serial port 1
COM2 Serial port 2
Hardware Manual
12
Page 18
3. Each Component Function
Serial Port Interface (COM1, COM2)
The PANECON-PC is equipped with two RS-232C-compliant serial port connectors (Serial Port 1:
COM1 and Serial Port : COM2).
Table 3.2. COM1/COM2 Serial Port Inter Connector
Main unit connector D-SUB 9-pin (Male)
Pin no.
1
2
3
4
5
6
7
8
9
1 5
6
Signal
CD
RD
TD
DTR
GND
DSR
RTS
CTS
RI
9
Carrier detection
Received data
Transm it te d d at a
Data terminal ready
Signal ground
Data set ready
Request to send
Clear to send
Ring indica tor
Function
No.4-40UNC
Inch screw
Direction
In
In
Out
Out
-----
In
Out
In
In
Hardware Manual
13
Page 19
3 Each Component Function
Ethernet (UTP)
Table 3.3. Ethernet connector (RJ-45)
Connector type
LINK ACT
RJ-45
18
Pin No.
Singal name
1
2
3
4
5
6
7
8
TD+
TD-
RX+
N.C.
N.C.
RX-
N.C.
N.C.
Function
Transmitted data (+) output
Transmitted data (-) output
Received data (+) input
Not connected
Not connected
Received data (-) input
Not connected
Not connected
LED indicator
- LINK(Green)
Indicates the LINK status. (Comes on when the link is established.)
- ACT(Orange)
Goes on to indicate that data is being transmitted/received. (Blinking when data is
transmitted/received)
Hardware Manual
14
Page 20
3. Each Component Function
PCMCIA (PCMCIA)
PCMCIA compliant card slots are provided [TYPE II×2 (TYPE III×1) size].
Slot 1
Slot 2
Front (LCD) side
↓
Figure 3.2. Slot Numbers and Locations
CAUTION
A type III card should be inserted into slot 2.
Power Supply to the Card
The voltage that can be used and the current capacity of each slot are as shown below:
Table 3.4. Power Supply to the Card
Voltage Current capacity (Max.)
+5V 250mA/Slot
+3.3V 250mA/Slot
+12V Not supplied.
USB port (USB)
The PANECON-PC is equipped with USB interface 2 channels.
Table3.5. USB connector
4
USB
1
Pin No. Signal name
1 Vcc
2 DATA+
3 DATA4 GND
Hardware Manual
15
Page 21
3 Each Component Function
General-purpose I/O ports (I/O)
The unit has four channels of general-purpose insulated I/O port.
Refer to the bundled CD-ROM(CONTEC SDK for CE420) for programming this ports.
Table 3.6. General-purpose I/O ports connector
113
↓ Front (LCD) side
Pin No. Signal name Remarks
1 PI_PCOM General-purpose input
(plus common)
2 PI(0) General-purpose Input 0
3 PI(1) General-purpose Input 1
4 PI(2) General-purpose Input 2
5 PI(3) General-purpose Input 3
6 P_PO(0) General-purpose Output 0+
7 N_PO(0) General-purpose Output 08 P_PO(1) General-purpose Output 1+
9 N_PO(1) General-purpose Output 1-
10 P_PO(2) General-purpose Output 2+
11 N_PO(2) General-purpose Output 212 P_PO(3) General-purpose Output 3+
13 N_PO(3) General-purpose Output 3-
Connector: MC1,5/13-GF-3,5(PHOENIX CONTACT)
Cable connector: MC1,5/13-STF-3,5(PHOENIX CONTACT)
Hardware Manual
16
Page 22
3. Each Component Function
Specifications
[Input section]
- Input specification : Photocoupler-insulated current drive input
- Input resistance : 3kΩ
- Number of input signals : 4
- Input protection circuit : Reverse-connection protection diode
- Input response time : Within 100μsec
- External circuit power supply : 12 - 24VDC(±10%)
[Output section]
- Output specification : Photocoupler-insulated open-collector output
- Output rating : 30VDC, 100mA max.
- No. of output signals : 4
- Output response time : Within 300μsec
Hardware Manual
17
Page 23
3 Each Component Function
External Connection
PI_PCOM
10kΩ
Figure 3.3. Input circuit
330Ω
PC357
Figure 3.4. Output circuit
P_PO(0) - P_PO(2)
2SD780A
4.7k
Ω
N_PO(0) - N_PO(2)
I/O connector
3kΩ
1/2W
PI(0) - PI(2)
I/O connector
Load
Input
contact
(External cuiruit)
External power supply
(12 - 24VDC)
External power supply
(Max. 30VDC)
Hardware Manual
18
Page 24
3. Each Component Function
AC adapter jack
This jack accepts the optional AC adapter [IPC-ACAP12-01].
Do not plug any other AC adapter into the AC adapter jack.
Table 3.7. AD adapter jack pinouts
Pin No. Name
+12V input
1
GND
2
CAUTION
1
2
When the AC adapter jack is used, the unit requires no power input via the power input connector.
As the AC adapter, be sure to use the option [IPC-ACAP12-01].
Power supply input connector
The power supply to be used must conform to the following specifications:
- Power supply voltage: +12VDC±5%
- Power supply capacity: 2.5A or more
The following table lists the pin specifications of the power connector on the back of the unit.
Table 3.8. Power input connector pinouts
Connector type +12VDC input connector
Type MC1,5/3-GF-3,81 (PHOENIX CONTACT)
1
2
3
Pin No. Signal name
1 FG(Frame Gnd)
2 GND
3 +12V
* Use the bundled MC1,5/3-STF-3,81 (PHOENIX CONTACT) for the connector on the cable side.
CAUTION
- Connect a power supply to either the power connector or the AC adapter jack. Never connect it to
both of them, or the unit can cause faults.
- If you use a power supply other than the option, be sure to take safety measures for the power
supply, such as overload protection. Use meticulous care not to use the power supply at wrong
polarities or voltage as doing so can break the unit and/or the power supply.
Hardware Manual
19
Page 25
3 Each Component Function
External Speaker Output Termi n al (SPK)
Connector type: HSJ1456-010330 (HOSIDEN)
Table 3.9. External Speaker Terminal
Pin no.
1
2
3
Signal
GND
Analog signal(R)
Analog signal(L)
Remarks
---
Speaker(Right)
Speaker(Left)
1pin
GND
2pin
R Analog signal
3pin
L Analog signal
Applicable connector: Small jack of φ3.5mm
Full-scale output level 1.0Vrms(Typ.)
Touch Panel
The PANECON-PC is equipped with an analog touch panel that enables keyboard-less, mouse-less
operations.
Refer to the software manual for details on how to use the touch panel.
Table 3.10. Touch panel specifications
Model IPC-PT/SV10 series
Detection method Analog resistive
Active area 133 x 100(mm)
Surface treatment No glare
Resolution 4096 x 4096 (emulated in 640 x 480 mode)
Operating lifetime 1 million touches minimum
(as tested by mechanical touching under 300g of force at a rate of two presses per second)
Hardware Manual
20
Page 26
3. Each Component Function
DIP-Switch setting
Table 3.11. SW list
Silk Function Remarks
SW2 Setting the OS operation 8-bits
SW1 Opened SW to user 4-bits
DIP switch for Opened SW to user (SW1)
SW1 is a general-purpose switch available for use by the application.
Refer to the bundled CD-ROM(CONTEC SDK for CE420) for details on how to use this DIP switch.
SW1
34
2
ON
1
Figure 3.5. DIP switch
DIP switch for Setup of OS operation (SW2)
This switch sets OS operation. For details, refer to the software manual.
Factory setting
ON
Back side of unit
12345678
Figure 3.6. Setup of OS operation
CAUTION
To use the unit normally, leave the DIP switch as above.
WA RN ING
Operating a connector or jumper on the internal CPU board, which is not covered by this manual,
can cause the unit to malfunction or develop operational problems. Never touch any of those
on-board connectors and jumpers.
Hardware Manual
21
Page 27
3 Each Component Function
LED display
POWER
USER
Figure 3.7. LED display
POWER LED (Side and front view) : Two colors (green/orange)
The same function with the POWER LED on the front side of this unit.
It turns on orange or green when starting. After it starts, it always turns on green.
Turning on Orange: When internal NFDISK drive is read and written.
Turning on Green: Times except the above-mentioned.
USER LED : Three colors (green/yellow/red)
USR LED is a general-purpose three-colors switch available for use by the application.
For more details on the method of using this USR LED, refer to the software manual.
Hardware Manual
22
Page 28
4. Hardware Setup
4. Hardware Setup
Installation Requirements
To maintain the ambient temperature within the installation environment requirement range, provide a
gap of 30mm or more between the main unit and any adjacent equipment.
Panel
30mm or more
(Top view)
30mm or more
(Side view)
30mm or more
(Side view)
30mm or more
30mm or more
(Side view)
Side view
(Bottom view)
Bottom view
Figure 4.1. Distances between the PANECON-PC and Its Vicinity
Card removal prevention fitting
(1) Insert a PC or CF card.
(2) Clip the pawl on the bottom of the fitting into the long slot on the PANECON-PC unit.
(3) Use a screw to attach the top of the fitting.
PCMCIA Card
Figure 4.2. Attaching the card removal prevention fitting
Hardware Manual
Panel
23
Page 29
4 Hardware Setup
Back light exchange
The backlight used in the LCD module has a limited life. When it expires and requires replacement,
contact your local CONTEC sales office.
Attaching the Fitting Used to Attach to the Main Unit
(1) Hold the main unit from the outside of the panel.
Figure 4.3. Attaching the Fitting Used to Attach to the Main Unit < 1 / 2 >
(2) Hold the attachment from the inside of the panel.
Fitting
Main unit
Tightening the screw excessively
can break the unit.
The appropriate tightening torque
to take drip-proof effect is 0.6 N/m.
Panel
Figure 4.3. Attaching the Fitting Used to Attach to the Main Unit < 2 / 2 >
Hardware Manual
24
Page 30
4. Hardware Setup
Panel cut dimensions Figure
+1
199
-0
+1
-0
155
Panel thickness range 1.6 - 7mm
[mm]
Figure 4.4. Panel cut dimensions figure
CAUTION
Use a panel with a thickness in the range 1.6 - 7mm.
Removing the cover for OS operation setup DIP switch (SW2)
When setting the SW2, you need to remove the back cover.
(1) Undo the 2 flat-head screws and remove the cover.
Figure 4.5. Removing the cover for OS operation setup DIP switch
Hardware Manual
25
Page 31
4 Hardware Setup
AC adapter removal prevention fitting
(1) Insert the plug of AC adapter.
(2) Use the screw to fasten the fitting.
Figure 4.6. Attaching the code removal prevention fitting
Hardware Manual
26
Page 32
5. List of Options
5. List of Options
Screen protective sheets
- IPC-CV6 : Screen protective sheets for 6.4inch (10 sheets)
Stand
- IPC-SND-03 : Desk stand
AC adapter
- IPC-ACAP12-01 : +12VDC output AC adapter
Manual
- IPC-PT/SV10DC1-HMJ : Hardware manual (Japanese)
- IPC-SH4CE4-SMJ : Software manual (Japanese)
- IPC-SH4CE4-SME : Software manual (English)
Hardware Manual
27
Page 33
IPC-PT/SV10DC1-4E
Hardware Manual
IPC-PT/SV10DC1-HME
CONTEC CO., LTD. July 2008 Edition
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Japanese http://www.contec.co.jp/
English http://www.contec.com/
Chinese http://www.contec.com.cn/
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD. [07092008]
[06162004] Management No. A-46-875
[07092008_rev5] Parts No. LYDT853
Loading...