Contec DIO-1616TB-PE, DIO-3232B-PE User Manual
PC-HELPER
Digital I/O Board
with High-Speed Opto-Isolation
for PCI Express
DIO-1616TB-PE
User’s Guide
CONTEC CO.,LTD.
Check Your Package
Thank you for purchasing the CONTEC product.
The product consists of the items listed below.
Check, with the following list, that your package is complete. If you discover damaged or missing
items, contact your retailer.
Product Configuration List
- Board [DIO-1616TB-PE] …1
- First step guide …1
- CD-ROM *1 [API-PAC(W32)] …1
*1 The CD-ROM contains the driver software and User’s Guide (this guide)
Board
DIO-1616TB-PE
First step guide
CD-ROM
[API-PAC(W32)]
i
Copyright
Copyright 2007 CONTEC CO., LTD. ALL RIGHTS RESERVED.
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this
document. The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document or for results obtained by the user as a result of using this product.
Trademarks
MS, Microsoft, Windows and MS-DOS are trademarks of Microsoft Corporation. Other brand and
product names are trademarks of their respective holder.
ii
DIO-1616TB-PE
Table of Contents
Check Your P ackage................................................................................................................................ i
Copyright .................................................................................................................................................ii
Trademarks ..............................................................................................................................................ii
Table of Contents ...................................................................................................................................iii
1. BEFORE USING THE PRODUCT 1
About the Bo ard ......................................................................................................................................1
Features............................................................................................................................................. 1
Support Software.............................................................................................................................. 2
Cable & Connector (Option) ........................................................................................................3
Accessories (Option).....................................................................................................................3
Customer Support.................................................................................................................................... 4
Web Site ...........................................................................................................................................4
Limited Th r ee-Years Warranty............................................................................................................... 4
How to Obta in Service............................................................................................................................ 4
Liability ...................................................................................................................................................4
Safety Precautions................................................................................................................................... 5
Safety Information ...........................................................................................................................5
Handling Precautions.......................................................................................................................6
Environment..................................................................................................................................... 7
Inspection .........................................................................................................................................7
Storage.............................................................................................................................................. 7
Disposal ............................................................................................................................................7
2. SETUP 9
What is Setup?......................................................................................................................................... 9
Using the Bo ard under Win d ows Using the Driver Library API-PAC(W 32)............................... 9
Using the Board under Windows Using Software Other than the Driver Library
API-PAC(W32)................................................................................................................................9
Using the Board under an OS Other than Windows..................................................................... 10
Step 1 Installing the Software...............................................................................................................11
About the d r iver to be used............................................................................................................11
Starting th e Install Pro gram...........................................................................................................12
Select API-DIO(WDM) .................................................................................................................13
Select API-DIO(98/PC) .................................................................................................................14
Step 2 Setti ng the Hardw a re .................................................................................................................16
Parts of the Board and Factory Defa u lts ....................................................................................... 1 6
Setting the Board ID ......................................................................................................................17
Selecting Power Supply .................................................................................................................18
Plugging the Board......................................................................................................................... 19
DIO-1616TB-PE
iii
Step 3 Installing the Hardware..............................................................................................................20
Turning on the PC ..........................................................................................................................20
When Using API-DIO(WD M ) .......................................................................................................20
When Using API-DIO(98/PC)...................................................................................................... .23
Step4 Initi a lizing the So ftware..............................................................................................................26
When Using API-DIO(WD M ) .......................................................................................................26
When Using API-DIO(98/PC)...................................................................................................... .28
Updating th e Settings .....................................................................................................................28
Step 5 Check ing Operations with the Diagnosis Program...................................................................29
What is the Diagnosis P r o gram?....................................................................................................29
Check Metho d.................................................................................................................................29
Using the Di agnosis Prog r am.........................................................................................................30
Setup Troubleshooting...........................................................................................................................34
Symptoms and Actions...................................................................................................................34
If your problem cannot be resolved ...............................................................................................34
3. EXTERNAL CONNECTION 35
How to conn e ct the connectors .............................................................................................................35
Connector shape .............................................................................................................................35
Connector P i n Assignment.............................................................................................................36
Relationshi ps between API- PAC(W32) Lo gical Ports/B its and Connector Signal P ins.............37
Connecting I n put Signals ......................................................................................................................38
Input Circuit....................................................................................................................................38
Connecting a Switch.......................................................................................................................39
Connecting O utput Signals....................................................................................................................40
Output Circuit.................................................................................................................................40
Connection to the LED...................................................................................................................41
Surge Protection.....................................................................................................................................42
4. FUNCTION 43
Data I/O Function ..................................................................................................................................43
Data Input .......................................................................................................................................43
Data Output.....................................................................................................................................43
Monitoring Output Data .................................................................................................................43
Digital Filter...........................................................................................................................................44
Digital Filter Function Principle....................................................................................................44
Set Digital Filter Time....................................................................................................................44
Interrupt Control Func tion.....................................................................................................................45
Disabling/ en a b li ng I n t er ru p t s.........................................................................................................45
Selecting the Interrup t Edge ...........................................................................................................45
Clearing th e Interrupt S t atus and Int errupt Sign al ........................................................................4 6
iv
DIO-1616TB-PE
5. ABOUT SOFTWARE 47
CD-ROM Directory Stru c ture ..............................................................................................................47
About Software for Windows............................................................................................................... 48
Accessing the Help File .................................................................................................................48
Using Sampl e Programs.................................................................................................................48
Uninstalling the Driver Libraries...................................................................................................50
About Software for Lin u x .....................................................................................................................51
Driver Software Instal l Procedure .................................................................................................51
Accessing the Help File .................................................................................................................52
Using Sampl e Programs.................................................................................................................52
Uninstalling the driver ...................................................................................................................52
6. ABOUT HARDWARE 53
For detailed technical information........................................................................................................53
Hardware sp e cification ......................................................................................................................... 54
Specification...................................................................................................................................54
Block Diagr am.......................................................................................................................................55
DIO-1616TB-PE
v
vi
DIO-1616TB-PE
1. Before Using the Product
1. Before Using the Product
This chapter provides information you should know before using the product.
About the Board
This product is a PCI Express board used to provide a digital signal I/O function on a PC. This product
features TTL level input 16ch, TTL level output 16ch opto-coupler isolated type with an intern al 5VDC
power supply that does not require external power. You can use all of the input signals as interrupt
inputs. In addition, digital filter function to prevent wrong recognition of input signals is provided.
Windows/Linux driver is bundled with this product.
Possible to be used as a data recording device for LabVIEW, with dedicated libraries.
Features
Opto-coupler isolated TTL level input, opto-coupler isolated TTL level output
This product has the opto-coupler isolated TTL level input 16ch and output 16ch whose high speed
response speed is 1µsec.
Opto-coupler bus isolation
As the PCI Express bus (PC) is isolated from the input and output interfaces by opto-couplers, this
product has excellent noise performance.
Power supply (5VDC 600mA) for driving opto-coupler
Power supply (5VDC 600mA) for driving opto-coupler is equipped. Whether or not to use the internal
power supply can be specified by jumpers in blocks of 16ch.
You can use all of the input signals as interrupt events.
You can use all of the input signals as interrupt events and also disable or enable the interrupt in bit
units and select the interrupt edge.
Windows/Linux compatible driver libraries are attached.
Using the attached driver library API-PAC(W32) makes it possible to create applications of
Windows/Linux. In addition, a diagnostic program by which the operations of hardware can be
checked is provided.
This product has a digital filter to prevent input signals from carrying noise or a chattering.
This product has a digital filter to prevent input signals from carrying noise or a chattering. All input
terminals can be added a digital filter, and the setting can be performed by software.
Functions and connectors are compatible with PCI compatible board PIO-16/16TB(PCI)H.
The functions same with PCI compatible board PIO-16/16TB(PCI)H are provided. In addition, as
there is compatibility in terms of connector shape and pin assignments, it is easy to migrate from the
existing system.
DIO-1616TB-PE
1
1. Before Using the Product
LabVIEW is supported by a plug-in of dedicated library VI-DAQ.
Using the dedicated library VI-DAQ makes it possible to make a LabVIEW application.
Support Software
You should use CONTEC support software according to your purpose and development environment.
Windows version of digital I/O driver
[Stored on the bundled CD-ROM driver library API-PAC(W32)]
The API-DIO(98/PC) is the Windows version driver library software that provides products in the form of Win32 API
functions (DLL). Various sample programms such as Visual Basic and Visual C++, etc and diagnostic program
useful for checking operation is provided.
< Operating environment >
OS Windows Vista, XP, Server 2003, 2000
Adaptation language Visual Basic, Visual C++, Visual C#, Delphi, C++ Builder
You can download the updated version from the CONTEC’s Web site (http://www.contec.com/apipac/). For more
details on the supported OS, applicable language and new information, please visit the CONTEC’s Web site.
API-DIO(WDM)/API-DIO(98/PC)
Linux version of digital I/O driver
API-DIO(LNX)
[Stored on the bundled CD-ROM driver library API-PAC(W32)]
The API-DIO(LNX) is the Linux version driver software which provides device drivers (modules) by shared library
and kernel version. Various sample programs of gcc are provided.
< Operating environment >
OS RedHatLinux, TurboLinux
Adaptation language gcc
You can download the updated version from the CONTEC’s Web site (http://www.contec.com/apipac/). For more
details on the supported OS, applicable language and new information, please visit the CONTEC’s Web site.
Data acquisition VI library for LabVIEW
(For details on supported distributions, refer to Help available after installation.)
(Available for downloading (free of charge) from
VI-DAQ
the CONTEC web site.)
This is a VI library to use in National Instruments LabVIEW.
VI-DAQ is created with a function form similar to that of LabVIEW's Data Acquisition VI, allowing you to use
various devices without complicated settings.
See http://www.contec.com/vidaq/ for details and download of VI-DAQ.
2
DIO-1616TB-PE
1. Before Using the Product
Cable & Connector (Option)
Flat Cable with Two 37-pin D- SUB Connectors : PCB37P-1.5 (1.5m)
:PCB37P-3 (3m)
:PCB37P-5 (5m)
Shielded Cable with Two 37-pin D- SUB Connectors : PCB37PS-0.5P (0.5m)
: PCB37PS-1.5P (1.5m)
: PCB37PS-3P (3m)
: PCB37PS-5P (5m)
Flat Cable with One 37-pin D- SUB Connector : PCA37P-1.5 (1.5m)
: PCA37P-3 (3m)
: PCA37P-5 (5m)
Shielded Cable with One 37-pin D- SUB Connector : PCA37PS-0.5P (0.5m)
: PCA37PS-1.5P (1.5m)
: PCA37PS-3P (3m)
: PCA37PS-5P (5m)
37-pin D-SUB Male Connector Set (5 Pieces) : CN5-D37M
Accessories (Option)
Screw Terminal (M3 x 37P) : EPD-37A *1
Screw Terminal (M3.5 x 37P) : EPD-37 *1
General Purpose Terminal : DTP-3A *1
Screw Terminal : DTP-4A *1
Signal Monitor for Digital I/O : CM-32(PC)E *1
*1 A PCB37P or PCB37PS optional cable is required separately.
DIO-1616TB-PE
3
1. Before Using the Product
Customer Support
CONTEC provides the following support services for you to use CONTEC products more efficiently
and comfortably.
Web Site
Japanese http://www.contec.co.jp/
English http://www.contec.com/
Chinese http://www.contec.com.cn/
Latest product information
CONTEC provides up-to-date information on products.
CONTEC also provides product manuals and various technical documents in the PDF.
Free download
You can download updated driver software and differential files as well as sample programs available in
several languages.
Note! For product information
Contact your retailer if you have any technical question about a CONTEC product or need its price,
delivery time, or estimate information.
Limited Three-Years Warranty
CONTEC products are warranted by CONTEC CO., LTD. to be free from defects in material and
workmanship for up to three years from the date of purchase by the original purchaser.
Repair will be free of charge only when this device is returned freight prepaid with a copy of the
original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office,
from which it was purchased.
This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and
original products. The warranty is not applicable if the device has been tampered with or damaged
through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in
which case repairs will be considered beyond the warranty policy.
How to Obtain Service
For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please
obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you
purchased before returning any product.
* No product will be accepted by CONTEC group without the RMA number.
Liability
The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor
be liable for any incidental or consequential damages due to such defect or consequences that arise from
inexperienced usage, misuse, or malfunction of this device.
4
DIO-1616TB-PE
1. Before Using the Product
Safety Precautions
Understand the following definitions and precautions to use the product safely.
Safety Information
This document provides safety information using the following symbols to prevent accidents resulting in
injury or death and the destruction of equipment and resources. Understand the meanings of these
labels to operate the equipment safely.
DANGER
WARNING
CAUTION
DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury or in property damage.
DIO-1616TB-PE
5
1. Before Using the Product
Handling Precautions
DANGER
Do not use the product where it is exposed to flammable or corrosive gas. Doing so may result in
an explosion, fire, electric shock, or failure.
CAUTION
- There are switches and jumpers on this product that need to be set in advance. Be sure to check
these before installing this product.
- Only set the switches and jumpers on this product to the specified settings.
Otherwise, this product may malfunction, overheat, or cause a failure.
- Do not strike or bend this product.
Otherwise, this product may malfunction, overheat, cause a failure or breakage.
- Do not touch this product's metal plated terminals (edge connector) with your hands.
Otherwise, this product may malfunction, overheat, or cause a failure.
If the terminals are touched by someone's hands, clean the terminals with industrial alcohol.
- Do not install or remove this product to or from the extension slot while the computer's power is
turne d on. And also d o not connect th i s product a nd external de vice while the p ower is turned o n.
Otherwise, this product may malfunction, overheat, or cause a failure.
Be sure that the personal computer or the I/O extension unit power is turned off.
- Make sure that your PC or extension unit can supply ample power to all this products installed.
Insufficiently energized product s could malfunction, overheat, or cause a failure.
- The specifications of this product are subject to change without notice for enhancement and quality
improvement.
Even when using the product continuously, be sure to read the manual and understand the contents.
- Do not modify the product. CONTEC will bear no responsibility for any problems, etc., resulting
from modifying this product.
- Regardless of the foregoing statements, CONTEC is not liable for any damages whatsoever
(including damages for loss of business profits) arising out of the use or inability to use this
CONTEC product or the information contained herein.
6
DIO-1616TB-PE
1. Before Using the Product
Environment
Use this product in the following environment. If used in an unauthorized environment, this product
may overheat, malfunction, or cause a failure.
Operating temperature
0 - 50°C
Humidity
10 - 90%RH (No condensation)
Corrosive gases
None
Floating dust particles
Not to be excessive
Inspection
Inspect the product periodically as follows to use it safely.
- Check that the bus connector
of the board and its cable have
been plugged correctly.
- Check that the board has
no dust or foreign matter adhering.
- The gold-plated leads of the bus connector
have no stain or corrosion.
Storage
When storing this product, keep it in its original packing form.
(1) Put this product in the storage bag.
(2) Wrap it in the packing material, and then put it in the box.
(3) Store the package at room temperature at a place free from direct sunlight, moisture, shock,
vibration, magnetism, and static electricity.
Disposal
When disposing of the product, follow the disposal procedures stipulated under the relevant laws and
municipal ordinances.
DIO-1616TB-PE
7
1. Before Using the Product
8
DIO-1616TB-PE
2. Setup
2. Setup
This chapter explains how to set up this product.
What is Setup?
Setup means a series of steps to take before the product can be used.
Different steps are required for software and hardware.
The setup procedure varies with the OS and applications used.
Using the Board under Windows
Using the Driver Library API-PAC(W32)
This section describes the setup procedure to be performed before you can start developing application
programs for the board using the bundled CD-ROM “Driver Library API-PAC(W32)”.
Taking the following steps sets up the software and hardware. You can use the diagnosis program later
to check whether the software and hardware function normally.
Step 1 Installing the Software
Step 2 Setting the Hardware
Step 3 Installing the Hardware
Step 4 Initializing the Software
Step 5 Checking Operations with the Diagnosis Program
If Setup fails to be performed normally, see the “Setup Troubleshooting” section at the end of this
chapter.
Using the Board under Windows
Using Software Other than the Driver Library API-PAC(W32)
For setting up software other than API-PAC(W32), refer to the manual for that software. See also the
following parts of this manual as required.
This chapter Step 2 Setting the Hardware
This chapter Step 3 Installing the Hardware
Chapter 3 External Connection
Chapter 6 About Hardware
DIO-1616TB-PE
9
2. Setup
Using the Board under an OS Other than Windows
For using the board under Linux, see the following parts of this manual.
This chapter Step 2 Setting the Hardware
Chapter 3 External Connection
Chapter 5 About Software
Chapter 6 About Hardware
For using the board under an OS other than Windows and Linux, see the following parts of this manual.
This chapter Step 2 Setting the Hardware
Chapter 3 External Connection
Chapter 6 About Hardware
10
DIO-1616TB-PE
2. Setup
Step 1 Installing the Software
This section describes how to install the Driver libraries.
Before installing the hardware on your PC, install the Driver libraries from the bundled
API-PAC(W32) CD-ROM.
The following description assumes the operating system as Windows XP. Although some user
interfaces are different depending on the OS used, the basic procedure is the same.
About the driver to be used
Two digital I/O drivers are available : API-DIO(WDM) and API-DIO(98/PC).
API-DIO(WDM) is a new driver to perform digital I/O under Windows.
API-DIO(WDM) was developed to improve the conventional product version of API-DIO(98/PC) in the
ease of use and functionality.
It is advisable to use API-DIO(WDM) for you to use an digital I/O device. API-DIO(WDM) will
support new OS and devices in the future but will not support Windows NT 4.0, Windows 95, ISA bus.
Use API-DIO(98/PC) if your operating environment contains such an unsupported piece of software or
hardware.
Check the following selection guide to easily select the driver to be used.
OS to be used
Windows Vista
Windows XP/Windows 2000
PCI bus, PC Card
Use the digital board for
the fisrt time?
Yes
Language to be used
VC.Net, VB.Net, VC#.Net
VC6, VB6
API-DIO(WDM)
DIO-1616TB-PE
Device type
Wind ows Me/98/9 5
Wind ows NT 4.0
ISA Bus
Already used.
The existing system
upgrade using
API-DIO(98/PC)?
No
VC2, 4, 5, VB4, 5,
Delphi, C++Builder
Yes
API-DIO(98/PC)
11
2. Setup
Starting the Install Program
(1)
Load the CD-ROM [API-PAC(W32)] on your PC.
(2)
The API-PAC(W32) Installer window appears automatically.
If the panel does not appear, run (CD-ROM drive letter):\AUTORUN.exe.
(3)
Click on the [Install Development or Execution Environment] button.
* When using the Window s V ista, dri ver i s automatically installed.
CAUTION
Before installing the software in Windows Vista, XP, Server 2003 and 2000, log in as a user with
administrator privileges.
12
DIO-1616TB-PE
Loading...