Contec DIO-1616L-PE Quick Start Manual
Isolated Digital I/O board
for PCI Express
DIO-1616L-PE
Item
Specification
Input
Input format
Opto-coupler isolated input
(Compatible with current sink output) (Negative logic *1)
Number of input
signal channels
16ch (all available for interrupts) (1 common in 16ch)
Input resistance
4.7k
Input ON current
2.0mA or more
Input OFF current
0.16mA or less
Interrupt
16 interrupt input signals are arranged into a single output of
interrupt signal INTA.
An interrupt is generated at the rising edge (HIGH-to-LOW
transition) or falling edge (LOW-to-HIGH transition).
Response time
Within 200sec
Output
Output format
Opto-coupler isolated open collector output (current sink type)
(Negative logic *1)
Number of output
signal channels
16ch (1 common)
Output
rating
Output
voltage
35VDC (Max.)
Output
current
100mA (par channel) (Max.)
Residual voltage with
output on
0.5V or less (Output current50mA), 1.0V or less (Output
current100mA)
Surge protector
Zener diode RD47FM(NEC) or equivalent to it
Response time
Within 200sec
Common
Built-in power
None
Allowable distance of
signal extension
Approx. 50m (depending on wiring environment)
I/O address
Any 32-byte boundary
Interruption level
1 level use
Max. board count for
connection
16 boards including the master board
Isolated Power
1000Vrms
External circuit power
supply
12 - 24VDC(±10%)
Power consumption
3.3VDC 350mA
Operating condition
0 - 50°C, 10 - 90%RH (No condensation)
Bus specification
PCI Express Base Specification Rev. 1.0a x1
Dimension (mm)
121.69(L) x 110.18(H)
Connector
37 pin D-SUB connector [F (female) type]
DCLC-J37SAF-20L9E [mfd by JAE] or equivalent to it
Weight
130g
Features
Specification
* Specifications, color and design of the products are subject to
change without notice.
Opto-coupler isolated input (supporting current sink
output) and opto-coupler isolated open-collector output
(current sink type)
This product has the opto-coupler isolated input 16ch
(supporting current sink output) whose response speed is
200sec and opto-coupler isolated open-collector output 16ch
(current sink type).
Common terminal provided per 16ch, capable of supporting a
different external power supply Supporting driver voltages of 12
- 24 VDC for I/O
Opto-coupler bus isolation
As the PCI Express bus (PC) is isolated from the input and
output interfaces by opto-couplers, this product has excellent
noise performance.
You can use all of the input signals as interrupt events.
You can use all of the input signals as interrupt events and also
disable or enable the interrupt in bit units and select the
interrupt edge.
Windows/Linux compatible driver libraries are attached.
Using the attached driver library API-PAC(W32) makes it
possible to create applications of Windows/Linux. In addition,
a diagnostic program by which the operations of hardware can
be checked is provided.
This product has a digital filter to prevent input signals
from carrying noise or a chattering.
This product has a digital filter to prevent input signals from
carrying noise or a chattering. All input terminals can be
added a digital filter, and the setting can be performed by
software.
Output circuits include zener diodes for surge voltage
protection and overcurrent protection circuit.
Zener diodes are connected to the output circuits to protect
against surge voltages. Similarly, overcurrent protection
circuits are fitted to each group of 8ch outputs.
Functions and connectors are compatible with PCI
compatible board PIO-16/16L(PCI)H.
The functions same with PCI compatible board
PIO-16/16L(PCI)H are provided.
In addition, as there is compatibility in terms of connector
shape and pin assignments, it is easy to migrate from the
existing system.
Ver.2.11
This product is a PCI Express bus-compliant interface board
that extends the digital signal I/O functions of a PC.
This product is a 12 - 24VDC opto-coupler isolated type with
opto-coupler isolated input 16ch and opto-coupler isolated
open-collector output 16ch. You can use all of the input
signals as interrupt inputs. Equipped with the digital filter
function and output transistor protection circuit (surge voltage
protection and overcurrent protection).
Windows/Linux driver is bundled with this product.
Possible to be used as a data recording device for LabVIEW,
with dedicated libraries.
LabVIEW is supported by a plug-in of dedicated library
VI-DAQ.
Using the dedicated library VI-DAQ makes it possible to create
each application for LabVIEW.
*1 Data “0” and “1” correspond to the High and Low levels, respectively.
DIO-1616L-PE 1
[mm]
121.69(L)
110.18(H)
The standard outside dimension (L) is
the distance from the end of the board to
the outer surface of the slot cover.
DIO-1616L-PE
Optocoupler
Optocoupler
Opto-
coupler
&
Transistors
Opto-
coupler
&
Transistors
Control
Circuits
Interrupt
Control
Circuit
PCI Express BUS
External digital
Output Port 1
(8ch, Group 3)
External digital
input Port 0
(8ch, Group 0)
External digital
input Port 1
(8ch, Group 1)
External digital
Output Port 0
(8ch, Group 2)
Cable & Connector
Accessories
Packing List
Block Diagram
Support Software
Ver.2.11
Board Dimensions
Flat Cable with One 37-pin D- SUB Connector
: PCA37P-1.5 (1.5m)
: PCA37P-3 (3m)
: PCA37P-5 (5m)
Shielded Cable with One 37-pin D- SUB Connector
: PCA37PS-0.5P (0.5m)
: PCA37PS-1.5P (1.5m)
: PCA37PS-3P (3m)
: PCA37PS-5P (5m)
Windows version of digital I/O driver
API-DIO(WDM)/API-DIO(98/PC)
[Stored on the bundled CD-ROM driver library API-PAC(W32)]
The API-DIO(98/PC) is the Windows version driver library
software that provides products in the form of Win32 API
functions (DLL). Various sample programs such as Visual
Basic and Visual C++, etc and diagnostic program useful for
checking operation is provided.
< Operating environment >
OS Windows Vista, Windows XP, Server
2003, 2000
Adaptation language Visual Basic, Visual C++, Visual C#,
Delphi, C++ Builder
You can download the updated version from the CONTEC’s
Web site (http://www.contec.com/apipac/). For more details
on the supported OS, applicable language and new information,
please visit the CONTEC’s Web site.
Linux version of digital I/O driver API-DIO(LNX)
[Stored on the bundled CD-ROM driver library API-PAC(W32)]
Connector (Option)
37-pin D-SUB Male Connector Set (5 Pieces)
: CN5-D37M
Accessories (Option)
Screw Terminal (M3 x 37P) : EPD-37A *1
Screw Terminal (M3.5 x 37P) : EPD-37 *1
General Purpose Terminal : DTP-3A *1
Screw Terminal : DTP-4A *1
Signal Monitor for Digital I/O : CM-32(PC)E *1
*1 A PCB37P or PCB37PS optional cable is required separately.
* Check the CONTEC’s Web site for more information on these options.
Board [DIO-1616L-PE] …1
First step guide … 1
CD-ROM *1 [API-PAC(W32)] …1
Warranty Certificate …1
Serial number label …1
*1 The CD-ROM contains the driver software and User’s Guide.
The API-DIO(LNX) is the Linux version driver software which
provides device drivers (modules) by shared library and kernel
version. Various sample programs of gcc are provided.
< Operating environment >
OS RedHatLinux, TurboLinux
(For details on supported distributions,
refer to Help available after installation.)
Adaptation language gcc
You can download the updated version from the CONTEC’s
Web site (http://www.contec.com/apipac/). For more details
on the supported OS, applicable language and new information,
please visit the CONTEC’s Web site.
Data acquisition VI library for LabVIEW VI-DAQ
(Available for downloading (free of charge) from the
CONTEC web site.)
This is a VI library to use in National Instruments LabVIEW.
VI-DAQ is created with a function form similar to that of
LabVIEW's Data Acquisition VI, allowing you to use various
devices without complicated settings.
See http://www.contec.com/vidaq/ for details and download of
VI-DAQ.
Cable (Option)
Flat Cable with Two 37-pin D- SUB Connectors
: PCB37P-1.5 (1.5m)
: PCB37P-3 (3m)
: PCB37P-5 (5m)
Shielded Cable with Two 37-pin D- SUB Connectors
: PCB37PS-0.5P (0.5m)
: PCB37PS-1.5P (1.5m)
: PCB37PS-3P (3m)
: PCB37PS-5P (5m)
DIO-1616L-PE 2
Loading...