Contec BX-100n-DC5000-C01, BX-100n-DC5121-C01, BX-100n-DC5000-C02, BX-100n-DC5311-C02 User Manual

Download

Page 1

IPC Series

BOX-PC for BX100n Series

User’s Manual

CONTEC CO.,LTD.

Page 2

Check Your Package

Thank you for purchasing the CONTEC product. The product consists of the items listed below. Check, with the following list, that your package is complete. If you discover damaged or missing items, contact your retailer. If you use IPC-SLIB-01 (driver&utility software set), download it from the CONTEC’s Web site. Product Configuration List

BX-100n-DC5000-C01

Name Pcs. Pcs. Pcs.

BOX-PC

The attachment fittings

CF card removal prevention fitting 1 1 1 *1

USB removal prevention fitting (base)

USB removal prevention fitting (angle)

Washer assembled screw (M3 x 6) 4 4 4

Washer assembled screw (M3 x 8, black)

Washer assembled and cross recessed hexagonal bolt (M4 x 10, black) Power supply connector complete set

Power connector 1 1 1

Contact 4 4 4

Cable clamp

DVI-analog RGB conversion adapter

Product guide

IPC Precaution List 1 1 1 Royalty consent contract

Setup Procedure Document Notes on using Windows Embedded

Standard

Recovery Media *2 None 1 1

*1 It is attached to the main body.

*2 Please confirm latest information on the CONTEC homepage though the manual is stored in Recovery Media

(\MANUAL).

BX-100n-DC5000-C02

1 1 1

2 2 2

1 1 1

4 4 4

6 6 6

4 4 4

2 2 2

1 1 1

None 1 1

None None 1

BX-100n-DC5121-C01 BX-100n-DC5311-C02

BX-100n User’s manual

Page 3

(

)

Product Configuration Image

DVI-analog RGB conversion

CF card removal prevention fitting

Washer assembled and cross recessed hexagonal bolt (M4 x 10, black)

Cable clamp

Windows

Embedded

Standard

Notes

Notes on using Windows Embedded Standard

Product guide

The attachment fittings

IPC

Precaution List

IPC Precaution List

BOX-PC * This product is BX-100n-DC5xxx-C02.

USB removal prevention fitting (base)

USB removal prevention fitting (angle)

Royalty

consent contract

Royalty consent contract

* See the Product Configuration List to check if all the components are included for the specified number of units.

Product guide

Washer assembled screw

M3 x 6

Washer assembled screw (M3 x 8, black)

Setup Procedure

Document

Setup Procedure Document

Contact

Power connector

Power supply connector complete set

Recovery Media *2

Copyright

No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., LTD.

CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this document.

The information in this document is subject to change without notice.

All relevant issues have been considered in the preparation of this document. Should you notice an omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.

Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may appear in this document or for results obtained by the user as a result of using this product.

Trademarks

Intel, Intel Atom, Intel Core and Celeron are registered trademarks of Intel Corporation. MS, Microsoft and Windows are trademarks of Microsoft Corporation. Other brand and product names are trademarks of their respective holder.

BX-100n User’s manual

Page 4

Check your package .................................................................................................................................i

Copyright .................................................................................................................................................ii

Trademarks ..............................................................................................................................................ii

Table of Contents ...................................................................................................................................iii

1. INTRODUCTION 1

About the Product ................................................................................................................................... 1

Features............................................................................................................................................. 2

Supported OS ...................................................................................................................................3

Support Software (Model with multi-signal I/O) ........................................................................... 4

Customer Support.................................................................................................................................... 5

Web Site ........................................................................................................................................... 5

Limited One-Year Warranty ................................................................................................................... 5

How to Obtain Service ............................................................................................................................ 5

Liability ...................................................................................................................................................5

Safety Precautions ................................................................................................................................... 6

Safety Information ........................................................................................................................... 6

Caution on the BX-100n Series .......................................................................................................6

2. SYSTEM REFERENCE 9

Specification ............................................................................................................................................ 9

Power Management Features ................................................................................................................ 13

Power Requirements ............................................................................................................................. 13

Power Consumption ....................................................................................................................... 13

Physical Dimensions .............................................................................................................................14

3. HARDWARE SETUP 17

Before Using the Product for the First Time ........................................................................................ 17

Hardware Setup ..................................................................................................................................... 18

Attaching the CF Attachment Fittings .......................................................................................... 18

Attaching the Attachment Fittings ................................................................................................ 18

Attaching the FG ............................................................................................................................ 19

Fastening the Cable ........................................................................................................................ 19

Installing the Hard Disk................................................................................................................. 20

Installation Requirements ..............................................................................................................21

BX-100n User’s manual

iii

Page 5

4. EACH COMPONENT FUNCTION 27

Component Name ..................................................................................................................................27

Front View ......................................................................................................................................27

Side View ........................................................................................................................................27

Back View.......................................................................................................................................27

System Configuration ............................................................................................................................29

Component Function .............................................................................................................................30

LED: POWER, ACCESS, STATUS .............................................................................................30

DC Power Input Connector : DC-IN .............................................................................................30

POWER SW ...................................................................................................................................31

Line out Interface : LINE OUT......................................................................................................31

MIC in Interface : MIC ..................................................................................................................31

Serial-ATA : S-ATA1 - 2...............................................................................................................31

Giga bit-Ethernet : LAN 1 – 2 .......................................................................................................32

USB Ports .......................................................................................................................................32

Serial Port Interface : SERIAL1 - 5...............................................................................................33

DVI Interface : DVI........................................................................................................................35

CF Card Connector (Primary IDE Connection) : CF1 - 2 ............................................................37

RAS Functions : RAS.....................................................................................................................38

Watchdog Timer .............................................................................................................................39

General-purpose I/O and Remote Reset ........................................................................................43

BUS EXPANDER (PCIe) ..............................................................................................................47

AIO..................................................................................................................................................48

DIO..................................................................................................................................................52

CNT.................................................................................................................................................53

5. BIOS SETUP 55

Introduction............................................................................................................................................55

Starting Setup .................................................................................................................................55

Using Setup .....................................................................................................................................56

Getting Help....................................................................................................................................56

In Case of Problems........................................................................................................................56

A Final Note About Setup..............................................................................................................56

Main Menu .............................................................................................................................................57

Setup Items .....................................................................................................................................57

Standard CMOS Setup ..........................................................................................................................59

Main Menu Selections ...........................................................................................................................60

IDE Adapters ..................................................................................................................................61

Advanced BIOS Features Setup ............................................................................................................62

CPU Feature ...........................................................................................................................................63

Hard Disk Boot Priority ........................................................................................................................64

Virus Warning ................................................................................................................................65

BX-100n User’s manual

Page 6

Advanced Chipset Features Setup ........................................................................................................70

PCI Express Root Port Function ........................................................................................................... 73

VGA setting........................................................................................................................................... 74

Watch Dog Timer Setting ..................................................................................................................... 75

Integrated Peripherals ........................................................................................................................... 76

OnChip IDE Device ..............................................................................................................................77

On Chip Serial ATA setting.................................................................................................................. 80

Onboard Device..................................................................................................................................... 82

Super IO Device .................................................................................................................................... 85

Power Management Setup ....................................................................................................................88

PnP/PCI Configuration Setup ...............................................................................................................93

IRQ n Resources.................................................................................................................................... 95

PCI Express relative items .................................................................................................................... 98

PC Health Status.................................................................................................................................... 99

Frequency/Voltage Control................................................................................................................. 101

Defaults Menu ..................................................................................................................................... 102

Supervisor /User Password Setting..................................................................................................... 103

Exit Selecting ...................................................................................................................................... 104

POST Messages................................................................................................................................... 104

POST Beep ..........................................................................................................................................104

Error Messages .................................................................................................................................... 105

Locations and Settings of CMOS/ROM Clear SW............................................................................ 109

6. RAID CONFIGURATION OF SATS CONNECTED HDD 111

RAID Configuration Utility................................................................................................................ 111

Run RAID Configuration Utility ................................................................................................. 111

Configuring the Striping (RAID 0) ............................................................................................. 112

When Configuring Mirroring (RAID1) with 2 New HDDs ....................................................... 114

OS Installation of SATA Connected HDD .................................................................................115

Create DriveFD ............................................................................................................................115

Install Windows XP on a SATA connected HDD ......................................................................116

BX-100n User’s manual

Page 7

7. APPENDIX 117

Memory Map .......................................................................................................................................117

I/O Port Addresses ...............................................................................................................................118

Interrupt Level List ..............................................................................................................................119

POST Codes .........................................................................................................................................120

COM I/O Address and Register Function...........................................................................................125

Watch-Dog-Timer................................................................................................................................131

8. LIST OF OPTIONS 135

BX-100n User’s manual

Page 8

1. Introduction

1. Introduction About the Product

This product is a fanless PC for embedded use based on an Atom processor N270 and a 945GSE (GMA950 incorporated) chipset. Operates in less power while ensuring sufficient performance, and permits installation in an A4-sized or smaller footprint with about 50mm in height "resource-saving PC" contributes downsizing and power-saving of equipment to reduce your running cost and to promote energy efficiency.

Embedded-type CPU and chip set have been adopted. The use of readily available parts ensures the ease of the use of the product. In addition, the use of a Contec-customized BIOS allows support to be provided at the BIOS level.

*1 installed vertically

This product is available in two types of models: one, with HDD; the other, with multi-signal I/O.

< Model with HDD >

The model can incorporate up to two 2.5-inch SATA HDDs, which enhances RAS feature. Windows XP Professional installed model that adopts HDD supporting wider temperature range is most suitable as a unit embedded into bulk data server. It is also capable of mirroring with two HDDs.

< Model with multi-signal I/O >

It has analog I/O, digital I/O, and counter input features equivalent to three of CONTEC's measurement control boards (AIO-163202F-PE, DIO-1616L-PE, CNT-3204MT-LPE). Best for data collection and control employing various sensors/devices.

Model CPU Memory Pre-install OS

HDD

multi-signal I/O

BX-100n-DC5000-C01 None Model with BX-100n-DC5121-C01 Windows XP Professional

BX-100n-DC5000-C02 None Model with BX-100n-DC5311-C02

Intel Atom

Processor N270

(1.60GHz)

1GB

(storage)

(Japanese),

(40GB SATA HDD)

Windows Embedded

Standard (Japanese),

(2GB CF)

. The

HDD, RAS I/O

Have None

None Have

BX-100n User’s manual

Page 9

1. Introduction

Features

< Model with HDD >

- Able to contain HDD that can handle large amounts of data It can incorporate up to two 2.5-inch SATA HDDs that make it most suitable as a unit embedded into bulk data server. It is also capable of mirroring between two HDDs.

- Major types of peripherals are supported with rich interfaces including the two CF card slots In addition to extended interfaces such as 1000BASE-T x 2, USB2.0 x 4, serial (RS-232C x 5, RS-485/422 x 1), it also includes RAS and three units of general-purpose I/O. Two slots available for CF cards.

< Model with multi-signal I/O >

- Immediate measurement control enabled by internal analog I/O, digital I/O, and counter input features It contains analog I/O, digital I/O, and counter input features equivalent to CONTEC's measurement control boards (AIO-163202F-PE, DIO-1616L-PE, CNT-3204MT-LPE). A set of this product features measurement control that can measure voltage, detect location, etc.

- Major types of peripherals are supported with rich interfaces including the two CF card slots It has a variety of extended interface such as 1000BASE-T x 2, USB2.0 x 4, serial (RS-232C x 2). It has 2 CF card slots that can use for OS and data. They are very useful because you can use one slot for system start-up and the other for maintenance, system log, or taking away the collected data.

< Common >

- Serving the downsizing of equipment, a small footprint design for A4-sized or smaller installation area

The product adopts space-saving design for A4-sized or smaller installation area 182(W) x 270(D) x 35(H), permitting placement with opening of only 50mm equipment, fits any area with the aestheticness kept. It is also possible to attach to the VESA standard 75 x 75, 100 x 100mm using the optional fittings.

*1 installed vertically

. It largely serves downsizing of your

- Contributing to reduction of running cost and promotion of energy efficiency

It adopts the low-power platform with Intel (R) Atom(TM) Processor N270 1.60GHz (FSB 533MHz), 945GSE and ICH7M-DH chipset that realizes lower power consumption while ensuring sufficient performance.

- Slitless/fanless design that reduces maintenance work

It employs slitless/fanless designing achieved by the elimination of radiating slit and CPU fan. It is free from dusts and foreign objects, and the use the parts that degrades over the years is avoided in most case, resulting in drastic alleviation of the maintenance burden.

BX-100n User’s manual

Page 10

1. Introduction

- Remote power management function to reduce operation tasks This product supports timed/automated system start-up (Resume By Alarm). For example, it enables unattended operation, such as starting to show information of an establishment in unison at opening time. Also, it supports system start-up externally via network (Wake On LAN) and modem (Power On by Ring). It encourages significant labor saving in operation.

- Falling-off prevention tools and fixing clamps provided to avoid trouble caused by disconnected cable This product stays trouble-free, being equipped with USB removal prevention fitting and cable clamp for connectors with no locking mechanism, such as USB cable, and with hardware to properly mount and avoid falling out of CF card.

- Expandable with PCI boards and/or PCI Express boards By connecting a PCI Express Cable-based expansion chassis using one cable at extra cost, it can be expanded with up to thirteen expansion board.

- A wide range of power supplies (10.8 - 31.2VDC) supported

As the product supports a wide range of power (10.8 - 31.2VDC), it can be used in a variety of power environments.

- Safety design required for embedded applications

Retention of CMOS data by EEPROM allows the system to start up even when the battery has run out. Additionally, Windows Embedded Standard installed model realizes totally spindleless design with CF card adopted for the storage. It can utilize EWF feature of OS

that protects CF card from unnecessary write, i.e. relieves concern about the limitation of number of writes to CF card, and that prevents system from unintentional modification, as a result of consideration for reassurance in designing necessary for the purpose of embedding.

*1 installed vertically

*2 EWF (Enhanced Write Filter) is a function specific to Windows Embedded Standard that protects the disk from being actually written

redirecting the writing to RAM.

Supported OS

- Windows XP Professional (BX-100n-DC5121-C01)

- Windows Embedded Standard (BX-100n-DC5311-C02)

BX-100n User’s manual

Page 11

1. Introduction

Support Software (Model with multi-signal I/O)

You should use CONTEC support software according to your purpose and development environment.

Windows version of analog I/O driver

API-AIO(WDM)

[Installed on the main body]

These drivers are the Windows version of analog I/O driver library software that provides products in the form of Win32

API functions (DLL). Various sample programs such as Visual Basic and Visual C++, etc and diagnostic program

useful for checking operation is provided.

Windows version of digital I/O driver

API-DIO(WDM)

[Installed on the main body]

These drivers are the Windows version of digital I/O driver library software that provides products in the form of Win32

API functions (DLL). Various sample programs such as Visual Basic and Visual C++, etc and diagnostic program

useful for checking operation is provided.

Windows version of counter driver

API-CNT(WDM)

[Installed on the main body]

These drivers are the Windows version of

API functions (DLL). Various sample programs such as Visual Basic and Visual C++, etc and diagnostic program

useful for checking operation is provided.

counter

driver library software that provides products in the form of Win32

< Operating environment >

OS Windows Vista, XP, Server 2003, 2000

Adaptation language Visual Basic, Visual C++, Visual C#, Delphi, C++ Builder

For more details on the supported OS, applicable language and how to download the updated version, please visit the

CONTEC’s Web site (http://www.contec.com/apipac/).

BX-100n User’s manual

Page 12

1. Introduction

Customer Support

CONTEC provides the following support services for you to use CONTEC products more efficiently and comfortably.

Web Site

Japanese http://www.contec.co.jp/ English http://www.contec.com/ Chinese http://www.contec.com.cn/

Limited One-Year Warranty

CONTEC products are warranted by CONTEC CO., LTD. to be free from defects in material and workmanship for up to one year from the date of purchase by the original purchaser.

Repair will be free of charge only when this device is returned freight prepaid with a copy of the original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office, from which it was purchased.

This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and original products. The warranty is not applicable if the device has been tampered with or damaged through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in which case repairs will be considered beyond the warranty policy.

How to Obtain Service

For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you purchased before returning any product.

* No product will be accepted by CONTEC group without the RMA number.

Liability

The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor be liable for any incidental or consequential damages due to such defect or consequences that arise from inexperienced usage, misuse, or malfunction of this device.

BX-100n User’s manual

Page 13

1. Introduction

Safety Precautions

Understand the following definitions and precautions to use the product safely.

Safety Information

This document provides safety information using the following symbols to prevent accidents resulting in injury or death and the destruction of equipment and resources. Understand the meanings of these labels to operate the equipment safely.

DANGER

WAR NI NG

CAUTION

Caution on the BX-100n Series

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or in property damage.

Handling Precautions

WA RN IN G

- Always check that the power supply is turned off before connecting or disconnecting power cables.

- Do not modify the product.

- Always turn off the power before inserting or removing circuit boards or cables.

- This product is not intended for use in aerospace, space, nuclear power, medical equipment, or other applications that require a very high level of reliability. Do not use the product in such applications.

- If using this product in applications where safety is critical such as in railways, automotive, or disaster prevention or security systems, please contact your retailer.

- Do not attempt to replace the battery as inappropriate battery replacement poses a risk of explosion.

- For battery replacement, contact your retailer as it must be performed as a process of repair.

- When disposing of a used battery, follow the disposal procedures stipulated under the relevant laws and municipal ordinances.

BX-100n User’s manual

Page 14

1. Introduction

CAUTION

- Do not use or store this product in a location exposed to high or low temperature that exceeds range of specification or susceptible to rapid temperature changes. Example: - Exposure to direct sun

- In the vicinity of a heat source

- Do not use this product in extremely humid or dusty locations. It is extremely dangerous to use this product with its interior penetrated by water or any other fluid or conductive dust. If this product must be used in such an environment, install it on a dust-proof control panel, for example.

- Avoid using or storing this product in locations subject to shock or vibration that exceeds range of specification.

- Do not use this product in the vicinity of devices that generate strong magnetic force or noise. Such products will cause this product to malfunction.

- Do not use or store this product in the presence of chemicals.

- To clean this product, wipe it gently with a soft cloth dampened with either water or mild detergent. Do not use chemicals or a volatile solvent, such as benzene or thinner, to prevent pealing or discoloration of the paint.

- This product’s case may become hot. To avoid being burned, do not touch that section while this product is in operation or immediately after turning off the power. Avoid installation in a location where people may come into contact with that section.

- CONTEC does not provide any guarantee for the integrity of data on CF.

- Always disconnect the power cable from the receptacle before mounting or removing the expansion board, or before connecting or disconnecting any connector.

- To prevent corruption of files, always shutdown the OS before turning off this product.

- CONTEC reserves the right to refuse to service a product modified by the user.

- In the event of failure or abnormality (foul smells or excessive heat generation), unplug the power cord immediately and contact your retailer.

- To connect with peripherals, use a grounded, shielded cable.

- Before connecting/disconnecting CF or HDD, ensure that its power is turned off.

- Component Life:

(1) Battery---The internal calendar clock and CMOS RAM are backed by a Lithium primary battery.

(2) CF---------OS-installed model (BX-100n-DC5311-C02) uses a CF card in the OS storage area.

(3) HDD------OS-installed model (BX-100n-DC5121-C01) uses HDD for the OS storage area.

* Replacement of expendables is handled as a repair (there will be a charge).

The backup time at a temperature of 25°C with the power disconnected is 10 years or more.

Estimated failure rates: 100,000 rewrite cycles, 1,000,000 hours MTBF

Estimated failure rates: 300,000 hours MTBF

BX-100n User’s manual

Page 15

1. Introduction

BX-100n User’s manual

Page 16

2. System Reference

System Reference

Specification

Table 2.1. Functional Specification < 1 / 3 >

Model BX-100n-DC5000-C01

BX-100n-DC5121-C01 *1

Model Model with HDD Model with multi-signal I/O

CPU Intel(R) Atom(TM) Processor N270 1.60GHz (FSB533MHz)

Chip set Intel(R) 945GSE + ICH7M-DH

BIOS BIOS (mfd. by Award)

Memory 1GB, 200pin SO-DIMM socket x 1, PC2-4300 (DDR2 533) DDR2 SDRAM support

Video

System resolution

Audio AC97 compliant

Serial I/F RS-232C (general-purpose) : 5 channels

*1 : When using the S-ATA HDD MHY2040BH#ESW (mfd.by FUJITSU) *2 : The capacity of CF is a value when 1GB is calculated by 1 billion bytes. The capacity that can be recognized from

Controller Built in Intel 945 GSE

Video RAM Main memory shared

Video BIOS 64KB(C0000H-CFFFFH)

Display I/F DVI-I I/F x 1(29 pin connector x 1)

DVI 640 x 480, 800 x 600, 1,024 x 768, 1,152 x 864, 1,280 x 600, 1,280 x 720, 1,280 x 768,

1,280 x 960, 1,280 x 1,024, 1,360 x 768, 1,400 x 1,050, 1,600 x 900, 1,600 x 1,200, 1,856 x 1,392, 1,920 x 1,080, 1,920 x 1,200 (16,770,000 colors)

Analog RGB 640 x 480, 800 x 600, 1,024 x 768, 1,280 x 768, 1,280 x 1,024, 1,360 x 768, 1,400 x 1,050

OS might be displayed fewer than an actual value.

(16,770,000 colors)

LINE OUT: φ3.5 Stereo mini jack Full-scale output level 1.5Vrms (Typ.), Dual 50mW Amplifier MIC IN : φ3.5 Stereo mini jack Full-scale input level 1.3Vrms (Typ.)

2.5 inch SATA hard disk slot-in system x 2, Corresponding to RAID 0.1, serial ATA

1.0 standard port

BX-100n-DC5000-C01 : -, BX-100n-DC5121-C01 : HDD1 is finished mounting SATA HDD. (40GB, 1 partition) CF CARD Type I x 2 bootable CF card slot

BX-100n-DC5311-C02 : CF1 is finished mounting CF (2GB, 1 partition) *2

(SERIAL PORT1, 2, 3, 4, 5) 9pin D-SUB connector (male) Baud rate : 50 - 115,200bps RS-485/422 (general-purpose) : 1 channel [Inside the RAS Connector]

None Serial ATA I/F

None

RS-232C (general-purpose) : 2 channels (SERIAL PORT1, 2) 9pin D-SUB connector (male) Baud rate : 50 - 115,200bps

BX-100n-DC5000-C02 BX-100n-DC5311-C02

BX-100n User’s manual

Page 17

2. System Reference

Table 2.1. Functional Specification < 2 / 3 >

Model

I/F 1000BASE-T/100BASE-TX/10BASE-T RJ-45 connector x 2 (Wake On LAN support) LAN

Controller Intel 82573L Controller

USB I/F 4 channels (USB 2.0-compliant)

Keyboard/mouse I/F None *3

General-purpose I/O Inside the 15-pin D-SUB connector (female)

RAS function Inside the 15-pin D-SUB connector (female)

PCI Express cable PCI Express 1.0a(x1) standard port

Analog I/O equivalent to AIO-163202F-PE *4

Digital I/O equivalent to DIO-1616L-PE *5

Counter input equivalent to CNT-3204MT-LPE *6

*3 : Use USB I/F for the keyboard / mouse. *4 : For more details on this, refer to the manual for CONTEC’s analog I/O board AIO-163202F-PE. *5 : For more details on this, refer to the manual for CONTEC’s digital I/O board DIO-1616L-PE. *6 : For more details on this, refer to the manual for CONTEC’s up down counter board CNT-3204MT-LPE.

[RAS connector] Optocoupler isolated I/O 3 channels for each (However, when using, you need to switch between the output 1 channel and WDT external device, and between the input 1 channel and remote reset.)

[RAS connector] WDT: 1sec - 255sec (Reset, interrupt, and external output enabled by time up) Remote reset : Input signal from external part.

(18-pin PCI Express External Cabling connector x 1)

None Analog input : Single-end input

None Digital input : 16channels Optocoupler

None 4channels, LVTTL, 32bit up down counter,

BX-100n-DC5000-C01

BX-100n-DC5121-C01 *1

None

Analog output : 2channels, 16 bit,

Digital I/O : 8channels for each,

Counter : 2channels, 32bit up

Digital output : 16channels Optocoupler

10MHz (Max.) 2-phase / single-phase / single-phase input with gate control

BX-100n User’s manual

BX-100n-DC5000-C02 BX-100n-DC5311-C02

32channels, 16bit, 2μsec/ch(Max.)

10μsec(Max.)

LVTTL

count, 10MHz(Max.)

isolated input 12 - 24VDC,

corresponding to current sink output

isolated open collector output, current sink output

Page 18

2. System Reference

Table 2.1. Functional Specification < 3 / 3 >

Model

Hardware monitoring Monitoring CPU temperature, board temperature, power voltage

Watch dog timer Software programmable, 255 level (1sec - 255 sec)

Causes a reset upon time-out.

RTC/CMOS Lithium backup battery life : 10 years or more

Power Management

Rated input

Power

voltage

supply

Range of input voltage

Power consumption

External device power supply capacity

Physical dimensions (mm)

Weight

*7 : Use a power cable shorter than 3m.

The real-time clock is accurate within ±3 minutes (at 25°C) per month (ICH7 integrated RTC).

Power management setup via BIOS Power On by Ring / Wake On LAN Supports PC98/PC99 ACPI Power management

12 - 24VDC *7

10.8 - 31.2VDC

12V 4.0A (Max.), 24V 1.9A (Max.) 12V 4.0A (Max.), 24V 2.0A (Max.)

- CF card slot +3.3V : 1A (500mA x 2)

- USB I/F +5V : 2A (500mA x 4)

182 (W) x 270 (D) x 35(H) (No protrusions)

Without HDD : About 2.2kg With one slot of HDD : About 2.3kg With two slots of HDD : About 2.4kg

BX-100n-DC5000-C01

BX-100n-DC5121-C01 *1

About 2.1kg

BX-100n-DC5000-C02 BX-100n-DC5311-C02

BX-100n User’s manual

Page 19

2. System Reference

Table 2.2. Installation Environment Requirements

Model

Operating temperature *8

Storage temperature

Humidity

Floating dust particles

Corrosive gases

Line noise

Line-noise resistance

Ambient specifications

Vibration resistance

Impact resistance *11

Grounding

*8 : For more details on this, please refer to chapter 3, “Installation Requirements”. *9 : When AC/DC power unit “LDA100W-24-SN, LDA100W-12-SN” (by Cosel) is used. *10 : To use 1000BASE-T, you should keep its ambient temperature between 0 - 40°C. *11 : To use 1000BASE-T, you should keep its ambient temperature between 0 - 45°C. *12 : As for the case of model with multi-signal I/O (BX-100n-DC5000-C02, BX-100n-DC5311-C02), it is the same.

Static electricity resistance

Sweep resistance

BX-100n-DC5000-C01

BX-100n-DC5121-C01*1

0 - 45°C *10

-10 - 60°C

10 - 90%RH (No condensation)

Not to be excessive

None

AC line / ±2kV *9, Signal line / ±1kV (IEC61000-4-4 Level 3,EN61000-4-4 Level 3)

Contact discharge / ±4kV (IEC61000-4-2 Level 2, EN61000-4-2 Level 2) Atmospheric discharge / ±8kV (IEC61000-4-2 Level 3, EN61000-4-2 Level 3)

When HDD is on

When HDD is off *12

10G, half-sine shock for 11 ms in x, y, and z directions (JIS C60068-2-27-compliant, IEC60068-2-27-compliant)

Class D grounding (previous class 3 grounding), SG-FG / continuity

BX-100n-DC5000-C02 BX-100n-DC5311-C02

0 - 50°C *11

10 - 50Hz / 0.5G 25 min. each in x, y, and z directions (JIS C60068-2-6-compliant, IEC60068-2-6-compliant)

10 - 57Hz / semi-amplitude 0.15 mm 57 - 150Hz/2.0G 40 min. each in x, y, and z directions (JIS C60068-2-6-compliant, IEC60068-2-6-compliant)

BX-100n User’s manual

Page 20

2. System Reference

Power Management Features

- Support both ACPI (Advanced Configuration and Power Interface) and legacy (APM) power management.

- ACPI v2.0 compliant

- APM v1.2 compliant

- PCI bus clock run, Power Management Enable (PME) control, all with hardware automatic wake-up

- Multiple suspends power plane controls and suspends status indicators

- Normal, doze, suspend and conserve modes

- Global and local device power control

Power Requirements

Your system requires a clean, steady power source for reliable performance of the high frequency CPU on the product, the quality of the power supply is even more important. For the best performance makes sure your power supply provides a range of 10.8 V minimum to 31.2 V maximum DC power source.

Power Consumption

For typical configurations, the CPU card is designed to operate with at least a 60W power supply. The power supply must meet the following requirements :

- Rise time for power supply: 2 ms - 30 ms

The following table lists the power supply’s tolerances for DC voltages:

Table 2.3. DC voltage tolerance

DC Voltage Acceptable Tolerance

+ 12V - 24V + 10.8V - 31.2V

BX-100n User’s manual

Page 21

2. System Reference

Physical Dimensions

BX-100n-DC5xxx-C01

RAS

182

200

218

BUS EXPANDER

270 125 100

STATUS

1 2

VDC

12 - 24

M3 screws *2

8-φ5

543

140

M3 screws *1

[mm]

Surface of the cabinet

*1 : When you fasten the bundled attachment fittings to be fixed to the body, you should use the attached screws (M3 x 8).

Otherwise, the length (L) from the surface of the cabinet to the screw tip should be 6mm or less.

*2 : The length (L) from the surface of the cabinet to the screw tip should be 6mm or less.

Figure 2.1. BX-100n-DC5xxx-C01

BX-100n User’s manual

Page 22

2. System Reference

BX-100n-DC5xxx-C02

CNT

BUS EXPANDER

270 125

100

STATUS

1 2

DIO AIO

182

200

218

VDC

12 - 24

M3 screws *2

8-φ5

Surface of the cabinet

140

M3 screws *1

[mm]

*1 : When you fasten the bundled attachment fittings to be fixed to the body, you should use the attached screws (M3 x 8).

Otherwise, the length (L) from the surface of the cabinet to the screw tip should be 6mm or less.

*2 : The length (L) from the surface of the cabinet to the screw tip should be 6mm or less.

Figure 2.2. BX-100n-DC5xxx-C02

BX-100n User’s manual

Page 23

2. System Reference

BX-100n User’s manual

Page 24

3. Hardware Setup

Before Using the Product for the First Time

Follow the next steps to set up this product :

STEP1 By referring to the information in this chapter, install, connect and set this product.

STEP2 Connect cables.

Connect the cable of necessary external devices, such as keyboard and a display, to this product using appropriate cables.

STEP3 Turn on the power.

After verifying that you have correctly followed steps 1 and 2, turn on the power. If you find any abnormality after turning on the power, turn it off and check to see if the setup has been performed properly.

STEP4 Set up BIOS.

By referring to Chapter 5, set up BIOS. This setup requires a keyboard and a display.

* Before using this product, be sure to execute " LOAD SETUP DEFAULTS" to initialize

the BIOS settings to their default values. (See Chapter 5, "Main Menu.")

CAUTION

Be sure to connect the keyboard and mouse to it before turning the power on for the first time.

BX-100n User’s manual

Page 25

3. Hardware Setup

Hardware Setup

- Before you start, be sure that the power is turned off.

- Remove only those screws that are explained. Do not move any other screw.

Attaching the CF Attachment Fittings

(1) After inserting a CF Card, fasten the bundled CF attachment fittings with a screw.

Figure 3.1. Attaching the CF Attachment Fittings

CAUTION

- Insert the CF Card face up.

- Screw holes may be damaged if screws are tightened with a torque greater than the specified torque.The specified tightening torque is 3 - 3.5kgf⋅cm.

Attaching the Attachment Fittings

(1) Use screws to attach the bundled attachment fittings with a screw.

Do not tighten screws with excess force.

BX-100n-DC5xxx-C01 BX-100n-DC5xxx-C02

* Attached screw (M3 x 8)

Figure 3.2. Attaching the Attachment Fittings

CAUTION

Screw holes may be damaged if screws are tightened with a torque greater than the specified torque.

The specified tightening torque is 5 - 6kgf⋅cm.

BX-100n User’s manual

Page 26

3. Hardware Setup

Attaching the FG

(1) Use screws to attach the FG.

* Attached screw (M3 x 8)

Figure 3.3. Attaching the FG

CAUTION

The FG pin of this product is connected to the GND signal of the DC power connector (DC-IN).

Note that the connection cannot be cut off.

Fastening the Cable

This product comes with clamps for fixing cables.

Fastening the LINEOUT, USB Cable

(1) The system unit has a hole for attaching cable clamp to USB removal prevention fitting. Using a

cable clamp for a cable with lock-less connector, such as the LINEOUT and USB Cable, prevents the connector from being unplugged. Use the cable ties and cable clamps appropriately according to the connecting states and wiring directions of cables.

*1 Attached screw (M3 x 6) *2 Attached screw (M3 x 8)

Figure 3.4. Attaching the cable clamp

BX-100n User’s manual

Page 27

3. Hardware Setup

(2) The photo below shows an example of using a cable clamp. Fix the cable with a clamp without

applying stress to the connector.

Figure 3.5. Using example of cable clamp

Installing the Hard Disk

BX-100n-DC5xxx-C01 can incorporate 2.5-inch SATA hard disk on a slot-in basis.

< Installing > < Removing >

Handle

Figure 3.6. Installing the Hard Disk

Handle

BX-100n User’s manual

Page 28

3. Hardware Setup

Installation Requirements

Be sure that the ambient temperature is within the range specified in the installation environment requirement by making space between the product and device that generates heat or exhaust air.

BX-100n-DC5xxx-C01

Installable directions at operating temperature 0 - +45°C

: All type of installation (including diagonal installation)

°C

°C)

Floor

1 2

STATUS

CAUTION

To use 1000BASE-T, you should keep its ambient temperature between 0 - 40°C

Operating temperature : 0 - +45 (When using the 1000BASE-T : 0 - +40

(1)

12 - 24 VDC

Connector

12 - 24

VDC

RAS

BUS EXPANDER

Wall

1 2

STATUS

Wall

PCIe RAS

(6)(4)(3) (5)

STATUS

1 2

Wall

VDC

12 - 24

Connector

(2)

STATUS

1 2

Ceiling

VDC

12 - 24

Figure 3.7. Installation Orientation < BX-100n-DC5xxx-C01 >

CAUTION

Note that even though the ambient temperature is within the specified range, an operational

malfunction may occur if there is other device generating high heat; the radiation will influence the product to increase its temperature.

BX-100n User’s manual

Page 29

3. Hardware Setup

BX-100n-DC5xxx-C02

Installable directions at operating temperature 0 - +50°C

: All type of installation (including diagonal installation)

CAUTION

To use 1000BASE-T, you should keep its ambient temperature between 0 - 45°C

Operating temperature :

°C

0 - +50 (When using the 1000BASE-T :

°C)

0 - +45

(1)

12 - 24

VDC

Floor

1 2

STATUS

Connector

12 - 24

VDC

BUS EXPANDER CNT

Wall

STATUS

Wall

1 2

BUS EXPANDER CNT

(6)(4)(3) (5)

STATUS

1 2

Wall

VDC

12 - 24

Connector

(2)

STATUS

1 2

Ceiling

VDC

12 - 24

Figure 3.8. Installation Orientation < BX-100n-DC5xxx-C02 >

CAUTION

Note that even though the ambient temperature is within the specified range, an operational

malfunction may occur if there is other device generating high heat; the radiation will influence the product to increase its temperature.

BX-100n User’s manual

Page 30

3. Hardware Setup

Distances between this product and its vicinity

- BX-100n-DC5xxx-C01

100 mm or more

543

50mmormore

100 mm

or more

100 mm or more

50mm or more

STATUS

1 2

VDC 12 - 24

Figure 3.9. Distances between this product and its vicinity < BX-100n-DC5xxx-C01 >

CAUTION

Do not install this product into the fully-sealed space except the case in which the internal

temperature is adjustable by equipment such as air conditioner. Troubles such as operational malfunctions could be occurred by the temperature increase caused by long-term usage.

BX-100n User’s manual

Page 31

3. Hardware Setup

- BX-100n-DC5xxx-C02

100 mm or more

50mmormore

100 mm

or more

50mmormore

100 mm or more

50mm or more

STATUS

1 2

VDC 12 - 24

Figure 3.10. Distances between this product and its vicinity < BX-100n-DC5xxx-C02 >

CAUTION

Do not install this product into the fully-sealed space except the case in which the internal

temperature is adjustable by equipment such as air conditioner. Troubles such as operational malfunctions could be occurred by the temperature increase caused by long-term usage.

BX-100n User’s manual

Page 32

3. Hardware Setup

Ambient temperature

In this product, the ambient temperature is decided from the multiple measurement points as shown below. When making use of the product, the air current should be adjusted to prevent that all the temperatures measured at the measurement points exceed the specified temperature.

- BX-100n-DC5xxx-C01

measurement points

STATUS

1 2

VDC 12 - 24

50 50 50 50

543

12 - 24 VDC

1 2

STATUS

[mm]

- BX-100n-DC5xxx-C02

measurement points

STATUS

1 2

VDC

12 - 24

50 50 50 50

12 - 24

VDC

BX-100n User’s manual

1 2

STATUS

[mm]

Page 33

3. Hardware Setup

BX-100n User’s manual

Page 34

4. Each Component Function

4. Each Component Function Component Name

Front View

BX-100n-DC5xxx-C01, BX-100n-DC5xxx-C02

LINE

POWER

OUT

LED

12 - 24

MIC IN

VDC

POWER SW

DC-IN

Figure 4.1. Component Name < 1 / 3 >

Side View

BX-100n-DC5xxx-C01

Left side Right side

BX-100n-DC5xxx-C02

Left side Right side

DVI-I

USB

CF1 CF2

LAN1

LAN2

1 2

STATUS

LED

SERIAL1

ACCESS LED

Figure 4.1. Component Name < 2 / 3 >

Back View

BX-100n-DC5xxx-C01

S-ATA-LED S-ATA1

[Internal part]

BX-100n-DC5xxx-C02

DIO AIO

Figure 4.1. Component Name < 3 / 3 >

BX-100n User’s manual

S-ATA2 [Internal part]

Page 35

4. Each Component Function

Table 4.1. Component Function

Name Function

POWER-SW Power switch

POWER LED Power ON display LED

ACCESS LED IDE disk access display LED

STATUS LED Status LED

S-ATA LED S-ATA disk access display LED *1

DC-IN DC power input connector LINE OUT Line out (φ3.5 PHONE JACK) MIC IN Mike in (φ3.5 PHONE JACK)

LAN1 Ethernet 1000BASE-T/100BASE-TX/10BASE-T RJ-45 connector

LAN2 Ethernet 1000BASE-T/100BASE-TX/10BASE-T RJ-45 connector

USB USB port connector x 4

SERIAL1

SERIAL2

SERIAL3

SERIAL4

SERIAL5

DVI-I Display (29pin female)

CF1 CF card slot (IDE connection mastering)

CF2 CF card slot (IDE connection slaving)

S-ATA1 HDD slot (Serial-ATA) *1

S-ATA2 HDD slot (Serial-ATA) *1

RAS RAS function or RS-485 connector (15pin D-SUB/female) *1

BUS EXPANDER (PCIe)

AIO Analog I/O connector (96pin half pitch connector/female) *2

DIO Digital I/O connector (37pin D-SUB/male) *2

CNT Counter connector (68pin 0.8mm pitch connector) *2

*1 : It is for the BX-100n-DC5xxx-C01. *2 : It is for the BX-100n-DC5xxx-C02.

Serial port 1 connector (9pin D-SUB/male)

Serial port 2 connector (9pin D-SUB/male)

Serial port 3 connector (9pin D-SUB/male) *1

Serial port 4 connector (9pin D-SUB/male) *1

Serial port 5 connector (9pin D-SUB/male) *1

PCI Express Cable connector (18pin PCI Express External Cabling/female)

BX-100n User’s manual

Page 36

4. Each Component Function

System Configuration

BX-100n-DC5xxx-C01

USB2.0

FD drive

Printer

USB device such as CD-ROM drive .,etc

LINE OUT

4 C

Display

CF card

S T A

T U

LAN port (1,2)

SERIAL port

(1,2)

BUS EXPANDER (PCIe)

Figure 4.2. System Configuration < BX-100n-DC5xxx-C01 >

BX-100n-DC5xxx-C02

USB2.0

LINE OUT

FD drive

1 2

BUS EXPANDER (PCIe)

Printer

USB device such as CD-ROM drive .,etc

Display

CF card

T A

T U

LAN port (1,2)

SERIAL port (1,2)

Figure 4.3. System Configuration < BX-100n-DC5xxx-C02 >

RAS

DIO

CNT

BX-100n User’s manual

Page 37

4. Each Component Function

Component Function

LED: POWER, ACCESS, STATUS

There are 3 LED in front of this product.

Table 4.2. Display Contents of LED

LED name State Display contents

OFF Indicates that this product is switched off. POWER LED

ON (Green) Indicates that this product is switched on.

ACCESS LED ON (Orange) Indicates that the IDE device is being accessed.

OFF You can control the behavior of LED from the user application. *1 STATUS LED

Flashing, ON (Red) You can control the behavior of LED from the user application. *1

S-ATA LED ON (Orange) Indicates that the S-ATA device is being accessed.

*1 API that controls STATUS LED is available. See the API description file "mtdll_e.chm" included in

/RasUtility/Samples in the CONTEC’s Web site [IPC-SLIB-01] for details.

DC Power Input Connector : DC-IN

To supply the power, always use the power supply listed below.

Rated input voltage : 12 - 24VDC Range of input voltage : 10.8 - 31.2VDC Power capacity : BX-100n-DC5xxx-C01 12V 4.0A or more, 24V 1.9A or more : BX-100n-DC5xxx-C02 12V 4.0A or more, 24V 2.0A or more

Table 4.3. DC Power Connector

Connector type 9360-04P (mfd. by ALEX)

Pin No. Signal name

Applicable connector on the connector side

Housing : 9357-04 (mfd. by ALEX) or 5557-04R (mfd. by MOLEX) Contact : 4256T2-LF (AWG18-24) (mfd. by ALEX) or 5556 (AWG18-24) (mfd. by MOLEX)

1 GND

2 GND

3 12 - 24V

4 12 - 24V

Rise time of power supply

Vol ta ge

12V

2 - 30mS

Time

Figure 4.4. Graph of Rise Time of Power Supply

BX-100n User’s manual

Page 38

4. Each Component Function

POWER SW

POWER SW is provided.

Line out Interface : LINE OUT

A line output connector is provided. You can plug a headphone or amplifier-integrated speakers into this connector.

MIC in Interface : MIC

A MIC input connector is provided. You can plug a microphone to this connector for sound input.

Audio driver

The audio driver is required to use the microphone input and line output interfaces.

Install the appropriate audio driver for your OS from the CONTEC’s Web site CD-ROM [IPC-SLIB-01]. (For information on the latest version of IPC-SLIB-01, check the CONTEC's Web site.)

Serial-ATA : S-ATA1 - 2

This product is equipped with the serial-ATA 1.0-compliant controller, allowing a 2.5-inch SATA hard disk drive to the on-board connector using the bundled hard disk bracket.

BX-100n User’s manual

Page 39

4. Each Component Function

Giga bit-Ethernet : LAN 1 – 2

This product is equipped with 2 ports for giga bit.

- Network type : 1000BASE-T/100BASE-TX/10BASE-T

- Transmission speed * : 1000M/100M/10M bps

- Max. network path length : 100m/segment

- Controller : Intel 82573L

* Operation at 1000Mbps requires a category 5e cable.

Table 4.4. Giga bit-Ethernet Connector

Pin No.

LAN

Transmit LED

Link LED

1 TX+ TRD+(0)

2 TX- TRD-(0)

3 RX+ TRD+(1)

4 N.C. TRD+(2)

5 N.C. TRD-(2)

6 RX- TRD-(1)

7 N.C. TRD+(3)

8 N.C. TRD-(3)

LEDs for display of network statuses:

Right LED : Link LED Normal connection : Green ON, Operation : Green Blinking Left LED : Operation LED 10M : Off, 100M : Green, 1000M : Orange

Function

100BASE-TX 1000BASE-T

LAN drivers

Install the appropriate audio driver for your OS from the CONTEC’s Web site [IPC-SLIB-01]. (For information on the latest version of IPC-SLIB-01, check the CONTEC's web site.)

CAUTION

Attention should to be paid to the guaranteed operating range of temperature in using 1000BASE-T.

For more details on this, refer to chapter3, Installation Requirements. Note that the Ethernet should be configured as 100BASE-TX or 10BASE-T in using under the temperature 0 - 50°C.

USB Ports

This product is equipped with 4 channels for USB 2.0 interface.

Table 4.5. USB Connector

Pin No. Function

1 USB_VCC

2 USB-

BX-100n User’s manual

3 USB+

4 USB_GND

Page 40

4. Each Component Function

Serial Port Interface : SERIAL1 - 5

SERIAL1, 2, 3, 4, 5 (RS-232C Ports)

The product has 5 channels of RS-232C compliant serial ports supporting up to a baud rate of 115,200bps with a 16-byte transmission-dedicated data buffer and a 16-byte reception-dedicated data buffer. You can use “Chapter 5 BIOS Setup” to configure an I/O address, interrupt and unused state for each of the ports independently. (The same I/O address and IRQ cannot be shared with any other device.) Please refer to “Chapter 7 I/O Port Addresses” for more information on I/O address and register function.

Table 4.6. SERIAL 1, 2, 3, 4, 5 I/O Addresses and Interrupts

SERIAL

1 3F8h - 3FFh

2 2F8h - 2FFh IRQ 3

3*1 2A8h - 2AFh IRQ 6

4*1 2B0h - 2B7h IRQ 7

5*1 2C0h - 2C7h IRQ 10

RS-422/485 Port*1 2C8h - 2CFh IRQ 11

T.P Port (system reserved) *2 2A0h - 2A7h IRQ 5

*1 It is for the BX-100n-DC5xxx-C01 model only.

*2 Set as Disable when shipped. Not available since it is for the reserved device for the functional expansion in future.

The I/O address is fixed and can not be changed.

Table 4.7. Serial Port Connector

Connector used on

the product

I/O address Interrupt

9-pin D-SUB (MALE)

No.4-40UNC Inch screw threads

IRQ 4

Pin No.

Signal

name

1 CD Carrier detect Input

2 RD Received data Input

3 TD Transmitted data Output

4 DTR Data terminal ready Output

5 GND Signal ground -----

6 DSR Data set ready Input

7 RTS Request to send Output

8 CTS Clear to send Input

9 RI Ring indicator Input

Meaning Direction

BX-100n User’s manual

Page 41

4. Each Component Function

Table 4.8. RS-422/485 Port Connector (Inside the RAS Connector)

Pin No. Signal name Meaning

TX + Transmitted data +

TX - Transmitted data -

RX + Received data +

RX - Received data -

Reference For more information on the RAS connector see Table 4.12, "RAS connector".

RS-422/RS-485 Specifications

- Transmission method : RS-422/RS-485-compliant, asynchronous, serial transmission, half

duplex/full duplex

- Baud rate : 50 - 115,200bps (programmable)

- Signal extension distance : 1.2km Max.

Terminal Resister when RS-485 is in Use

It is set in BIOS setup menu. At the time of shipment, the setting is “no terminating resistance”.

For more details on this, please refer to Chapter 5, “Onboard Device”.

Control of Transmitted Data in Half-Duplex Mode

In half-duplex mode, the transmission buffer needs to be controlled in order to prevent collision of transmitted data. The BOX-PC uses RTS and controls the buffer with modem control register's bit 1. Transmission and reception gate control by the register setting of port address 4007h is allowed only for the RS-422/485 (Serial port D). For more information see section, "General-purpose I/O and Remote Reset" in Chapter 4.

Modem control register

(Set I/O address +4H) bit 1 : 0 … RTS is High. (Disable transmission) 1 … RTS is Low. (Enable transmission)

BX-100n User’s manual

Page 42

4. Each Component Function

DVI Interface : DVI

A DVI interface is provided. You can use it to connect a CRT (even a D-SUB 15 pin connector is acceptable by using the bundled DVI-analog RGB adapter) or a CONTEC Panel Link display. The connector is named DVI (DVI-I 29-pin connector).

Table 4.9. DVI Connector

Connector type DVI-I 29 pin

Pin No.

1 DATA2- 13 N.C. C1 RED

2 DATA2+ 14 +5V C2 GREEN

4 N.C. 16 HPD C4 HSYNC

5 N.C. 17 DATA0- C5 GND

6 DDC CLK 18 DATA0+

8 VSYNC 20 N.C.

9 DATA1- 21 N.C.

10 DATA1+ 22

2 N.C. 24 CLK-

Signal

name

DATA2

SHIELD

DDC

DATA

DATA1

SHIELD

Pin No.

15 GND C3 BLUE

23 CLK+

Signal

name

DATA0

SHIELD

DATA0

SHIELD

Pin No.

Signal

name

BX-100n User’s manual

Page 43

4. Each Component Function

Table 4.10. DVI-analog RGB conversion adapter

Connector type

39.40

DVI-I 29 pin

33.00

15.00

Pin No. Signal name Pin No. Signal name

1 RED 9 +5V

2 GREEN 10 GND

3 BLUE 11 N.C.

4 N.C. 12 DDC DATA

5 GND 13 HSYNC

6 GND 14 VSYNC

7 GND 15 DDC CLK

8 GND

6.20 5.80

30.00

Signal on analog RGB

[mm]

For the LCDs that can be connected, please refer to “Chapter 8 List of Options”.

Display driver

Install the appropriate audio driver for your OS from the CONTEC’s Web site [IPC-SLIB-01]. (For information on the latest version of IPC-SLIB-01, check the CONTEC's Web site.)

CAUTION

- You need to set the screen resolution if the display cable is not connected to this DVI-D interface at OS startup, but connected after OS startup (hereinafter referred to as “Late Insertion”). For more details on this, refer to the CONTEC’s Web site [IPC-SLIB-01].

- You need to set the screen resolution against the analog interface. For more details on the setting method, refer to the CONTEC’s Web site [IPC-SLIB-01].

- When using the DVI interface, resolution 640 x 480 may not be displayed normally. To display it normally, you need to set the screen resolution. For more details on the setting method, refer to the CONTEC’s Web site [IPC-SLIB-01].

- When the analog display is used, Windows MS-DOS may not be properly displayed in full-screen mode. This is because the frequency and resolution of Windows and MS-DOS (full-screen display) are the same due to the screen settings while the display parameters are different. For display, as only one parameter can be stored for one frequency or resolution, only either of Windows or MS-DOS screen can be displayed properly. In this case, change the resolution or display frequency of Windows so that it is not the same as for the MS-DOS display.

BX-100n User’s manual

Page 44

4. Each Component Function

CF Card Connector (Primary IDE Connection) : CF1 - 2

The CF Card (Type I : dedicated to the memory card) can be connected. Before you insert/remove the CF card, make sure that the power is switched off and the access LED is turned off.

Table 4.11. CF Card Connector

Connector used

on the product

50-socket header type (1.27mm pitch)

Pin No. Signal name Direction Pin No. Signal name Direction

1 GND 26 GND

2 DD3 I/O 27 DD11 I/O

3 DD4 I/O 28 DD12 I/O

4 DD5 I/O 29 DD13 I/O

5 DD6 I/O 30 DD14 I/O

6 DD7 I/O 31 DD15 I/O

7 CS0- Output 32 CD3- Output

8 GND 33 GND

9 GND 34 DIOR- Output

10 GND 35 DIOW- Output

11 GND 36 +3.3V

12 GND 37 INTRQ Input

13 +3.3V 38 +3.3V

14 GND 39 CSEL- Output

15 GND 40 N.C

16 GND 41 RESET- Output

17 GND 42 IOCHRDY Input

18 DA2 Output 43 DDRQ Input

19 DA1 Output 44 DDACK- Output

20 DA0 Output 45 DACT- Output

21 DD0 I/O 46 PDIAG- Output

22 DD1 I/O 47 DD8 I/O

23 DD2 I/O 48 DD9 I/O

24 N.C 49 DD10 I/O

25 GND 50 GND

BX-100n User’s manual

Page 45

4. Each Component Function

RAS Functions : RAS

A RAS port is provided for the BX-100n-DC5xxx-C01. This port offers watchdog timer, remote reset, and general-purpose I/O RAS functions.

Table 4.12. RAS Connector

Connector type 15pin D-SUB (FEMALE)

Pin No. Signal name Function

1 N.C. None

2 TX+ RS-485 transmitting line

3 RX+ RS-485 receiving line

4 NCOM Minus common dedicated to PO2

5 PO0 General-purpose output

6 NCOM General-purpose output minus common

7 PI1 General-purpose input

8 PCOM General-purpose input plus common

9 GND External speaker ground

10 TX- RS-485 transmitting line

11 RX- RS-485 receiving line

12 PO2/WDT

13 PO1 General-purpose output

14 PI2/IRQ General-purpose input or interrupt input

15 PI0 General-purpose input

CAUTION

Pin 4 NCOM (minus common dedicated to PO2) and pin 6 NCOM (minus common shared by PO0

and PO1) are electrically separated from each other.

No.4-40UNC Inch screw

915

General-purpose output or watch dog timer alarm output

threads

BX-100n User’s manual

Page 46

4. Each Component Function

Watchdog Timer

The watchdog timer is started by output of A5 to I/O port address 4002h. A second output of A5 to the same port within the specified expiration time once again triggers the watchdog timer. If a time-out occurs, a reset or an interrupt is generated according to the 4004h port setting or an alarm is output according to the 4004h port setting.

The time-out period can be set between 1 - 255 seconds depending on the timer value setting for the WDT counter port (4003h).

The watchdog timer stops by reading port 4002h. The alarm-out output is cancelled at the same time.

The alarm out is output from the RAS connector's PO2/WDT (pin 12) and cancelled when reset.

The alarm-out output can be set to BIOS startup by BIOS setup (see Chapter 5), watchdog timer startup, or watchdog timer time-up.

Specifications

- Time to be set: 1sec - 255sec

- Interrupt or reset: Resets or generates an interrupt at time-up (Port setting).

- External alarm output: Optocoupler isolated open-collector output (the output status is set by

- I/O addresses: 4000h - 4007h (RAS port)

software). For more information, see the general-purpose I/O specifications.

BX-100n User’s manual

Page 47

4. Each Component Function

How to Use the Watchdog Timer

BIOS setting

Power ON

Set event

output control

Output data to ports 4001h and 4004h to set the counter clock.

Instruct WDT

to stop

Read port 4002h, stop the WDT, and turn off alarm output.

Set timer value

Output set data to port 4003h.

Start & clear

WDT

Application

Output of A5h to port 4002h starts the WDT and output of A5h to the same port clears the timer.

* WDT : Watch Dog Timer

Modify timer

value?

YES

To modify the timer value during operation, the WDT needs to be stopped temporarily.

Figure 4.5. How to Use the Watchdog Timer Example usage :

To assign IRQ5 to the event whose time-up value is 15sec:

Out 4004h 01h : Set the event at the time of WDT expiration to IRQ5.

In 4002h : Stop the WDT timer and cancel the alarm.

Out 4003h 0Fh : Set the WDT expiration time to 15sec.

Out 4002h A5h : Start and clear the WDT.

In 4002h : Stop the WDT and cancel the alarm.

BX-100n User’s manual

Page 48

4. Each Component Function

* 4001h (bit4-6): Alarm out output control

D5 D4 D3 D2 D1

--- WD_S0

WD_S1 PO2_M PIM2 PIM1 PIM0RESET

D0D7

R/W (Default: XXXX0000b)

Figure 4.6. Alarm Out Output Control Port (4001h)

PO2_M : PO PO2/WDT pin output setting

0 : Set the RAS connector's PO2/WDT(12) signal to PO2 (general-purpose output). 1 : Set the RAS connector's PO2/WDT(12) signal to alarm out.

Table 4.13. WD_S1, WD_S0: Alarm-out Output Status Settings

External alarm output status

WD_S1 WD_S0

0 0 OFF OFF OFF ON

1 0 OFF OFF ON OFF

1 1 OFF ON ON OFF

0 1 OFF ON OFF ON

When power is

turned off

When BIOS

starts

When

WDT starts

When time

expires on WDT

* 4002h: WDT control

D6 D5 D4 D3 D2 D1 D0

R/W

Figure 4.7. WDT Control Port (4002h)

R : Cancels WDT stop/alarm.

Read data is undefined.

W : Start and clear the WDT

Write A5h to start and clear the WDT.

* 4003h: WDT counter

D6 D5 D4 D3 D2 D1 D0D7

T6 T5 T4 T3 T2 T1 T0T7

Figure 4.8. WDT Counter Port (4003h)

W : Writes watchdog timer count data.

Write watchdog timer counter expiration time data.

1sec → 01h

8sec → 08h 15sec → 0Fh 30sec → 1Eh

BX-100n User’s manual

Page 49

4. Each Component Function

* 4004h : Event output control

D5 D4 D3 D2 D1

--- ---

--- --- WM2 WM1 WM0RESET

D0D7

R/W (Default: XXXX0000b)

Figure 4.9. Event Output Control Port (4004h)

Table 4.14. WM2-WM0: Interrupt Output Modes

WM2 WM1 WM0 Interrupt output at occurrence of WDT errors

0 0 1

0 1 0

0 1 1

1 0 0

1 0 1

1 1 0 Output to NMI when time expires on the WDT.

Others Inhibits output when time expires on the WDT.

Output to IRQ5 when time expires on the WDT.

Output to IRQ7 when time expires on the WDT.

Reserved * Do not set this value.

Output to IRQ10 when time expires on the WDT.

Output to IRQ11 when time expires on the WDT.

Table 4.15. RESET: Reset Output Modes

RESET RESET output at occurrence of WDT errors

0 Inhibits RESET output when time expires on the WDT.

1 Allows RESET output when time expires on the WDT.

Note! : When time expires on WDT, the alarm-out is output irrelevant to the settings of the port for controlling event

output.

* 4005h : RAS status port

D6 D5 D4 D3 D2 D1 D0D7

WDT

R (Default: XXXXXXX0b)

Figure 4.10. RAS Status Port (4005h)

R : RAS status port

WDT : WDT status

This is the WDT status bit. This bit is cleared when the WDT stops (read port 4002h).

0 : The WDT is either stopped or counting.

1 : The time set on the WDT expired.

BX-100n User’s manual

Page 50

4. Each Component Function

General-purpose I/O and Remote Reset

The BOX-PC is equipped with three general-purpose insulated signals each for input and output. The input signals can also be used for interrupt input or remote reset input.

Specifications

[ Input ]

- Input specifications : Current-driven input by Optocoupler isolation

- Input resistance : 4.7kΩ

- Input signal count : 3 [One of them can be used for remote reset and interrupt input (bit2<fixed>)]

- Input protection circuit : Equipped with a reverse-connection protection diode

- Input response time : Less than 100μsec

- External circuit power supply: 12 - 24VDC (±10%)

[ Output ]

- Output specifications : Open-collector output by Optocoupler isolation

- Output rating : Max. 30VDC, 100mA

- Output signal count : 3 [One of them can be used for WDT alarm output. (bit2<fixed>)]

- Output response time : Less than 300μsec

[ Common ]

- I/O addresses 4000h and 4001h

How to Use General-purpose I/O and Remote Reset

Event output

control

...

Output data to port 4001h to set PI0, PI2 or PO2 mode.

...

I/O

Implement input and output with port 4000h.

Figure 4.11. How to Use General-purpose I/O and Remote Reset

BX-100n User’s manual

Page 51

4. Each Component Function

I/O Addresses and Instructions

* 4000h: General-purpose I/O

D6 D5 D4 D3 D2 D1 D0D7

PIO2 PIO1 PIO0

R/W

Figure 4.12. General-purpose Input Port (4000h)

R : Read data from PI0, PI1 and PI2.

W : Set data to be output to PO0, PO1 and PO2.

* 4001h (bit0-3): PI2/IRQ(14) event input control

D6 D5 D4 D3 D2 D1 D0

WD_S0WD_S1 PO2_M PIM2 PIM1 PIM0RESET

Figure 4.13. Event Input Control Port (4001h)

Table 4.16. PIM2 - PIM0 : Interrupt output mode

RIM2 RIM1 RIM0 PI2/IRQ (14) interrupt input

0 0 1

0 1 0

0 1 1 Reserved * Do not set this value.

1 0 0

1 0 1

1 1 0 Input the RAS connector's PI2/IRQ (14) signal to NMI.

Others

Input the RAS connector's PI2/IRQ (14) signal to IRQ5.

Input the RAS connector's PI2/IRQ (14) signal to IRQ7.

Input the RAS connector's PI2/IRQ (14) signal to IRQ10.

Input the RAS connector's PI2/IRQ (14) signal to IRQ11.

Inhibit the RAS connector's PI2/IRQ (14) signal interrupt to be set.

Table 4.17. RESET: Reset Input Modes

RESET PI2/IRQ (14)'s RESET input

0 Inhibit the remote reset input function of the RAS connector's PI2/IRQ (14) signal.

1 Use as the remote reset input function of the RAS connector's PI2/IRQ (14) signal.

CAUTION

A bit indicated with "rsv" is used by the system. Do not modify the bit.

BX-100n User’s manual

Page 52

4. Each Component Function

* 4007h: Control of RS-485 transmission and reception

D6 D5 D4 D3 D2 D1 D0D7

RE_GATE TE_GATE TE_SEL

rsv*

R/W (Default: XXXX0000b)

Figure 4.14. RS-485 Transmission and Reception Control Port (4007h)

TE_SEL : Select the RS-485 transmission enable signal.

0 : Sets the RTS signal to the RS-485 transmission enable signal. (factory setting)

1 : Sets the TE_GATE value to the RS-485 transmission enable signal.

TE_GATE : RS-485 transmission enable signal. Valid only when the TE_SEL value is "1."

0 : RS-485 transmission Enable (factory setting)

1 : RS-485 transmission Disable

RE_GATE : RS-485 transmission enable signal.

0 : RS-485 reception Enable (factory setting)

1 : RS-485 reception Disable

CAUTION

A bit indicated with "rsv" is used by the system. Do not modify the bit.

TXD

0 :Transmission

RTS

prohibited 1 :Transmission

permitted

TE_GATE

RE_GATE

RXD

TE_SEL

0 :Transmission permitted

1 :Transmission prohibited

0 :Receiving permitted

1 :Receiving prohibited

0 : Controlled by RTS 1 : Controlled by TE_GATE

0 1

RX-(11) RX+(3)

TX-(10) TX+(2)

RS485 Terminator Control

Enabled : On Disabled : Off

120kΩ

Figure 4.15. Half-Duplex Connection Method

BX-100n User’s manual

Page 53

4. Each Component Function

TXD

0 :Transmission

RTS

prohibited 1 :Transmission

permitted

0 :Transmission

TE_GATE

RE_GATE

RXD

RS485 Terminator Control

permitted 1 :Transmission

prohibited 0 :Receiving

permitted 1 :Receiving

prohibited

TE_SEL

Enabled : On Disabled : Off

0 : Controlled by RTS 1 : Controlled by TE_GATE

0 1

120kΩ

Figure 4.16. Full-Duplex Connection Method

External I/O Circuit

(PCOM2)

(IN)

Internal

reset

4.7kΩ

PC817

4.7kΩ 1/4W

(PI 0 - 2)

(External circuit)

Input

contact

RX-(11) RX+(3)

TX-(10) TX+(2)

External power (12 - 24VDC)

RAS connector

Figure 4.17. Input Circuit

(External circuit)

External power (Max. 30VDC)

510Ω

PC817

2N3904

4.7kΩ

(PO 0 - 2)

(NCOM)

RAS connector

Figure 4.18. Output Circuit

BX-100n User’s manual

Page 54

4. Each Component Function

BUS EXPANDER (PCIe)

This product is equipped with the PCI Express cable port. You can use CONTEC's abundant measurement control boards by connecting with our PCI Express Cable-based expansion chassis and CB-CE-1, the cable for Cable Express at extra cost.

Table 4.18. PCI Express cable Connector

Connector

type

Pin No.

Signal

name

1 Tx+

2 Tx-

Reserved None

PCI Express transmitting line

N.C. None

GND GND

N.C. None

GND GND

CAUTION

Function Pin No.

- PCI Express cable is 32-bit spec. We have not verified operation on boards for both 64bit and 32bit,

such as ADAPTEC's 39160SCSI board and Intel's Pro1000/MT network board.

- PCI Express bus is x1 spec. Buses requiring baud rate more than x1 (x16, etc.) cannot be used.

- Leave "Reserved" pins unconnected. Connecting these pins may cause a fault in this product.

18pin (FEMALE)

Signal

CPERST#

13 CLK+

14 CLK-

17 RX+

No.4-40UNC Inch screw threads

name

GND

Reset signal

N.C. None

PCI Express clock

N.C. None

PCI Express receiving line

RX-

Function

BX-100n User’s manual

Page 55

4. Each Component Function

AIO

BX-100n-DC5xxx-C02 features analog I/O.

This function is compatible with that of CONTEC's AIO-163202F-PE.

Pin Assignments of analog I/O connector < Single-Ended Input >

N.C. B48 A48 Analog Output 00 N.C. B47 A47 Analog Ground (for AO) N.C. B46 A46 Analog Output 01

Analog Input 08 B44 A44 Analog Input 00 Analog Input 24 B43 A43 Analog Input 16 Analog Input 09 B42 A42 Analog Input 01

Analog Input 25 B41 A41 Analog Input 17 Analog Ground (for AI) B40 A40 Analog Ground (for AI) Analog Ground (for AI) B39 A39 Analog Ground (for AI)

Analog Input 10 B38 A38 Analog Input 02

Analog Input 26 B37 A37 Analog Input 18

Analog Input 11 B36 A36 Analog Input 03

Analog Input 27 B35 A35 Analog Input 19 Analog Ground (for AI) B34 A34 Analog Ground (for AI) Analog Ground (for AI) B33 A33 Analog Ground (for AI)

Analog Input 12 B32 A32 Analog Input 04

Analog Input 28 B31 A31 Analog Input 20

Analog Input 13 B30 A30 Analog Input 05

Analog Input 29 B29 A29 Analog Input 21 Analog Ground (for AI) B28 A28 Analog Ground (for AI) Analog Ground (for AI) B27 A27 Analog Ground (for AI)

Analog Input 14 B26 A26 Analog Input 06

Analog Input 30 B25 A25 Analog Input 22

Analog Input 15 B24 A24 Analog Input 07

Analog Input 31 B23 A23 Analog Input 23 Analog Ground (for AI) B22 A22 Analog Ground (for AI) Analog Ground (for AI) B21 A21 Analog Ground (for AI)

Digital Output 00 B18 Digital Output 01 B17 A17 Digital Input 01 Digital Output 02 B16 A16 Digital Input 02 Digital Output 03 B15 A15 Digital Input 03 Digital Output 04 B14 A14 Digital Input 04 Digital Output 05 B13 A13 Digital Input 05 Digital Output 06 B12 A12 Digital Input 06

AO Control Signal Output 00 B10 A10 AI Control Signal Output 00 AO Control Signal Output 01 B09 A09 AI Control Signal Output 01

AO External Sampling Clock Input B07 A07 AI External Sampling Clock Input

AO External Stop Trigger Input B06 A06 AI External Stop Trigger Input

AO External Start Trigger Input B05 A05 AI External Start Trigger Input

Counter Gate Control Input 01 B02 A02 Counter Gate Control Input 00

Connec tor used : 96pin half pitch connector [M (male) type]

PCR-96LMD [HONDA TSUSHIN KOGYO CO.,] or equivalence to it

Connector pin assignment is compatible with that of CONTEC's AIO-163202F-PE.

- The numbers in square brackets [ ] are pin numbers designated by HONDA TSUSHIN KOGYO CO.,

Digital Output 07 B11 A11 Digital Input 07

Digital Ground B08 A08 Digital Ground

Counter UP Clock Input 01 B04 A04 Counter UP Clock Input 00

Control Output 01 B01

N.C. B45 A45 Analog Ground (for AO)

[49]

[1]

B48 A48

N.C. B20 A20 N.C. N.C. B19 A19 N.C.

B01

[96]

[48]

Reserved B03 A03 Reserved

18 Digital Input 00

A01

A01 Counter Outpu t 00

BX-100n User’s manual

Page 56

4. Each Component Function

Analog Input00 - Analog Input31

Analog Output00 - Analog Output01

Analog Ground Common analog ground for analog I/O signal.

AI External Start Trigger Input External trigger input signal for starting analog input sampling.

AI External Stop Trigger Input External trigger input signal for stopping analog input sampling.

AI External Sampling Clock Input External sampling clock input signal for analog input.

AI Control Signal Output 00 External output signal for analog input sampling clock.

AI Control Signal Output 01 External output signal for analog input status. Now, it is unconnected.

AO External Start Trigger Input External trigger input signal for starting analog output sampling.

AO External Stop Trigger Input External trigger input signal for stopping analog output sampling.

AO External Sampling Clock Input External sampling clock input signal for analog output.

AO Control Signal Output 00 External output signal for analog output sampling clock.

AO Control Signal Output 01 External output signal for analog output status. Now, it is unconnected.

Digital Input00 - Digital Input07 Digital input signal.

Digital Output00 - Digital Output07 Digital output signal. Counter Gate Control Input00 -

Counter Gate Control Input01 Counter Up Clock Input00 - Counter Up Clock Input01

Counter Output00 - Counter Output01 Count match output signal for counter.

Digital Ground

Reserved This pin is reserved.

N.C. This pin is left unconnected.

Analog input signal. The numbers correspond to channel numbers. Analog output signal. The numbers correspond to channel numbers.

Counter gate control input signal.

Counter up clock input signal.

Common digital ground for digital I/O signal, external trigger input signal, external sampling clock input signal, counter I/O signal.

Figure 4.19. Pin Assignments of analog I/O connector < Single-Ended Input >

CAUTION

- Do not connect any of the outputs and power outputs to the analog or digital ground. Neither connect outputs to each other. Doing either can result in a fault.

- If analog and digital ground are shorted together, noise on the digital signals may affect the analog signals. Accordingly, analog and digital ground should be separated.

- Leave "Reserved" pins unconnected. Connecting these pins may cause a fault in this product.

BX-100n User’s manual

Page 57

4. Each Component Function

Pin Assignments of analog I/O connector < Differential Input >

N.C.

B48 A48

N.C.

B47 A47

N.C.

B46 A46

N.C.

Analog Input 08[+]

Analog Input 08[-]

Analog Input 09[+]

Analog Input 09[-] Analog Ground (for AI) Analog Ground (for AI)

Analog Input 10[+]

Analog Input 10[-]

Analog Input 11[+]

Analog Input 11[-] Analog Ground (for AI) Analog Ground (for AI)

Analog Input 12[+]

Analog Input 12[-]

Analog Input 13[+]

Analog Input 13[-] Analog Ground (for AI) Analog Ground (for AI)

Analog Input 14[+]

Analog Input 14[-]

Analog Input 15[+]

Analog Input 15[-] Analog Ground (for AI) Analog Ground (for AI)

Digital Output 00 Digital Output 01 Digital Output 02 Digital Output 03 Digital Output 04 Digital Output 05 Digital Output 06

Digital Output 07 AO Control Signal Output 00 AO Control Signal Output 01

Digital Ground

AO External Sampling Clock Input

AO External Stop Trigger Input

AO External Start Trigger Input

Counter UP Clock Input 01

Reserved

Counter Gate Control Input 01

Counter Output 01

B45 A45 B44 A44 B43 A43 B42 A42 B41 A41 B40 A40 B39 A39 B38 A38 B37 A37 B36 A36 B35 A35 B34 A34 B33 A33

[49]

B48 A48

B32 A32 B31 A31 B30 A30 B29 A29 B28 A28 B27 A27 B26 A26 B25 A25 B24 A24 B23 A23 B22 A22 B21 A21

N.C.

B20 A20

N.C.

B19 A19 B18 A18 B17 A17

B01

B16 A16 B15 A15

[96]

B14 A14 B13 A13 B12 A12 B11 A11 B10 A10 B09 A09 B08 A08 B07 A07 B06 A06 B05 A05 B04 A04 B03 A03 B02 A02 B01

[1]

A01

[48]

Connector used : 96pin half pitch connector [M (male) type]

PCR-96LMD [HONDA TSUSHIN KOGYO CO.,] or equivalence to it

Connector pin assignment is compatible with that of CONTEC's AIO-163202F-PE.

- The numbers in square brackets [ ] are pin numbers designated by HONDA TSUSHIN KOGYO CO.,

Analog Output 00 Analog Ground (for AO) Analog Output 01 Analog Ground (for AO) Analog Input 00[+] Analog Input 00[-] Analog Input 01[+] Analog Input 01[-] Analog Ground (for AI) Analog Ground (for AI) Analog Input 02[+] Analog Input 02[-] Analog Input 03[+] Analog Input 03[-] Analog Ground (for AI) Analog Ground (for AI) Analog Input 04[+] Analog Input 04[-] Analog Input 05[+] Analog Input 05[-] Analog Ground (for AI) Analog Ground (for AI) Analog Input 06[+] Analog Input 06[-] Analog Input 07[+] Analog Input 07[-] Analog Ground (for AI) Analog Ground (for AI) N.C. N.C. Digital Input 00 Digital Input 01 Digital Input 02 Digital Input 03 Digital Input 04 Digital Input 05 Digital Input 06 Digital Input 07 AI Control Signal Output 00 AI Control Signal Output 01 Digital Ground AI External Sampling Clock Input AI External Stop Trigger Input AI External Start Trigger Input Counter UP Clock Input 00 Reserved Counter Gate Control Input 00 Counter Output 00

A01

BX-100n User’s manual

Page 58

4. Each Component Function

Analog Input00 - Analog Input15

Analog Output00 - Analog Output01

Analog Ground Common analog ground for analog I/O signals.