IPC Series
PANEL-PC 40 Series
Fanless, ARM Cortex-A8
User’s Manual
CONTEC CO., LTD.
PT-40NVF-DC353111
Name
Pcs.
Panel-PC
1
Power supply conn ector complete set
Power connector
1
Contact
4
Waterproof screw
4
Ferrite core
1
Cable clamp
1
Product guide
1
IPC Precaution List
1
Warranty Certifi cate
1
Serial number label
1
Waterproof packing
1
Check Your Package
Thank you for purchas i ng the CON TEC p rod uc t.
The product cons ists o f the ite ms lis ted be l ow.
Check, with the fol low ing l ist, t hat yo ur pa cka ge is co mple te. If you dis cove r damaged or missing it e ms, co ntac t your
retailer.
Product Configuration List
PT-40 User’s manual
i
IPC Precaution
List
XXXXXXXXXXXXX
XXXXXXXXXXXXX
IPC Pre caution List
PT-40NVF-DC353111
Waterproof packing
Power connector Contact
Waterproof screw
Ferrite core
Cable clamp
Product
guide
Product guide
Warranty Certificate
Warranty
Certificate
Serial number label
Product Configuration Image
* See the Product Configuration List to check i f all the components are included for the specified number of units.
Copyright
Copyright 2015 CONTEC CO., LTD. ALL RIGHTS RESERVED.
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this
document.
The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document or for results obtained by the user as a result of using this product.
Trademarks
MS, Microsoft and Windows are trademarks of Microsoft Corporation. Other brand and product names
are trademark s of their respectiv e holder.
PT-40 User’s manual
ii
Table of Contents
Check Your Package ............................................................................................................................ i
Copyright ............................................................................................................................................ ii
Trademarks .......................................................................................................................................... ii
Table of Contents ............................................................................................................................... iii
1. INTRODUCTION 1
About the Product ............................................................................................................................... 1
Features ........................................................................................................................................ 1
Supported OS ............................................................................................................................... 2
Customer Support................................................................................................................................ 3
Web Site ....................................................................................................................................... 3
Limited One-Year Warranty ............................................................................................................... 3
How to Obtai n Servic e ........................................................................................................................ 3
Liability ............................................................................................................................................... 3
Safety Precautions ............................................................................................................................... 4
Safety In f ormation ....................................................................................................................... 4
Caution on the PT-40 Series......................................................................................................... 4
2. SYSTEM REFERENCE 7
Specifications ...................................................................................................................................... 7
Power Requirements ........................................................................................................................... 9
Power Consumption ..................................................................................................................... 9
Physical Dimensions ......................................................................................................................... 10
3. HARDWARE SE TUP 11
Before Using the Product for the First Time ..................................................................................... 11
Hardwar e Setup ................................................................................................................................. 12
Attaching of FG .......................................................................................................................... 12
Fastening the Cable .................................................................................................................... 12
Hardwar e Setup .......................................................................................................................... 14
Installation Requirements ........................................................................................................... 16
4. EACH COMPONENT FUNCTION 19
Component Name .............................................................................................................................. 19
DC Power Input Connector : DC-IN .......................................................................................... 20
100M Ethernet : LAN ................................................................................................................ 21
USB Ports: USB ......................................................................................................................... 22
Serial Port Int erfa c e: SE RIAL .................................................................................................... 22
PT-40 User’s manual
iii
5. APPENDIX 23
Battery ............................................................................................................................................... 23
6. LIST OF OPTIONS 25
PT-40 User’s manual
iv
1. Introduction
1. Introduction
About the Pro duct
This product is an open-frame type PC equipped with a power saving ARM(R) CortexA8:600MHz processor and a fanless, small touch panel function.
It uses Windows Embedded Compact 7, an OS designed specifically for embedded systems.
Because the OS and user applications are loaded into RAM from the standard-equipped
SD card, this product does not require a shutdown process.
The front section uses the included packing to obtain dust proofing and waterproofing
compliant with IP65.
This product complies with the VESA standard and can be installed on an LCD arm.
This product can be used in a variety of applications as the controller of devices such as
operation terminals located in manufacturing lines, distribution systems, and other parts
of factories.
This product is equipped with a variety of expansion interfaces and can be used as a
general terminal in a wide variety of embedded applications. The one model of this
product listed below is available.
Windows
* In order to create Windows applications, "CONTEC SDK for CE 700" is also necessary. For details,
®
Embedded Compact 7 (Japanese version)
PT-40NVF-DC353111(memory 256MB, SD 512MB)
see the software manual.
Features
Contributes to reductions in energy usage
This product uses an SoC "AM3354" that is equipped with an ARM® processor (600MHz,
T.I. Cortex-A8) with a low power consumption platform, which achieves low power
consumption while still providing sufficient performance.
Fanless design that reduces maintenance and inspection work
This product has no CPU fan, uses an SD card for storage, and has a completely
spindleless design. Installing the panel using the included waterproof packing and screws
prevents the intrusion of dust and other foreign materials from the front (this achieves an
IP65 rating for the front). Also, the use of parts that degrade over time has been
minimized, which greatly reduces the burden of maintenance and inspection work.
Space-saving design contributes to the miniaturization of equipment
This touch panel PC uses a 5.7-inch LCD, which makes the PC compact and lightweight
(weighs approximately 0.8kg). This product contributes to the miniaturization of
equipment. Also, it complies with the 100 × 100mm VESA standard, so it can be installed
on an LCD arm.
PT-40 User’s manual
1
1. Introduction
Equipped with PC-standard expansion interfaces such as USB and LAN
This product is equipped with USB (1), 100BASE-T (1), and RS-232C (1) interfaces. The
drivers for the equipped interfaces are also installed as standard.
Equipped with "CONTEC Manager", a tool that supports system development
This product is equipped with "CONTEC Manager", a tool that provides assistance for
system development by way of functions such as an FTP server function, a scheduling
function, an automatic time adjustment function that uses NTP, and the Auto RUN
function.
Supported OS
- Windows Embedded Compact 7
PT-40 User’s manu al
2
1. Introduction
Customer Su pp ort
CONTEC provides the following support services for you to use CONTEC products more efficiently
and comfortably.
Web Site
Japanese http://www.contec.co.jp/
English http://www.contec.com/
Chinese http://www.contec.com.cn/
Latest product information
CONTEC provides up-to-date information on products.
CONTEC also provides product manuals and various technical documents in the PDF.
Free download
You can download updated driver software and differential files as well as sample programs available in
several languages.
Note! For product information
Contact your retailer if you have any technical question about a CONTEC product or need its price,
delivery time, or estimate information.
Limited One-Year Warranty
CONTEC products are warranted by CONTEC CO., LTD. to be free from defects in material and
workmanship for up to one year from the date of purchase by the original purchaser.
Repair will be free of charge only when this device is returned freight prepaid with a copy of the
original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group
office, from which it was purchased.
This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and
original products. The warranty is not applicable if the device has been tampered with or damaged
through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in
which case repairs will be considered beyond the warranty policy.
How to Obtain Service
For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please
obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you
purchased before returning any product.
* No product will be accepted by CONTEC group without the RMA number.
Liability
The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor
be liable for any incidental or consequential damages due to such defect or consequences that arise from
inexperienced usage, misuse, or malfunction of this device.
PT-40 User’s manual
3
1. Introduction
DANGER
WARNING
CA
UT
IO
N
CAUTION
WARNING
Safety Pr ecautions
Understand the following definitions and precautions to use the product safely.
Safety Information
This document provides safety information using the following symbols to prevent accidents resulting
in injury or death and the destruction of equipment and resources. Understand the meanings of these
labels to operate the equipment safely.
DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury or in property damage.
Caution on the PT-40 Series
Handling Precautions
Do not disassemble or modify the product or replace any of its parts. Doing so may lead to electric
shock, fire, or product failures. In addition, CONTEC may not be able to provide servicing for the
product if you modify it.
Do not rep lace the ba ttery with an inappropriate one, as doing so may lead to explosion s.
- Always check that the power supply is turned off before connecting or disconnecting power cables.
- This product is not intended for use in aerospace, space, nuclear power, medical equipment, or other
applications that require a very high level of reliability. Do not use the product in such applications.
- If using this product in applications where safety is critical such as in railways, automotive, or
disaster prevention or security systems, please contact your retailer.
PT-40 User’s manu al
4
1. Introduction
CAUTION
- Do not use or store this product in a location exposed to high or low temperature that exceeds range
of specifica tion or susceptible to rapid temperature changes.
Example: - Exposure to direct sun
- In the vicinity of a heat source
- Do not use t his product in extremely humid or dusty locations. It is extremely dangerous to use this
product with its interior penetrated by water or any other fluid or conductive dust. If this product
must be used in such an environment, install it on a dust-proof control panel, for example.
- Avoid using or storing this product in locations subject to shock or vibration that exceeds range of
specification.
- Do not use t his product in the vicinity of devices that generate strong magnetic force or noise. Such
products will cause this product to malfunction.
- Do not use or store this product in the presence of chemi cals.
- To clean this product, wipe it gently with a soft cloth dampened with either water or mild detergent.
Do not use chemicals or a volatile solvent, such as benzene or thinner, to prevent pealing or
discoloration of the paint.
- This product’s case may become hot. To avoid being burned, do not touch that section while this
product is in operation or immediately after turning off the power. Avoid installation in a location
where people may come into contact with that section.
- CONTEC does not provide any guarantee for the integrity of data on Storage medium.
- Be sure to disconnect the power cable from the outlet before connecting cables to and disconnecting
cables from the connectors and before configuring hardware settings such as switches.
-
Use grounded and shielded cables to connect to periphery devices.
-
When transporting the product, implement sufficient countermeasures to prevent the
product from being directly subjected to vibrations and impacts.
-
If the battery needs to be replaced, the product will have to be repaired. In this
situation, contact your retailer or CONTEC group office.
-
When disposing of used batteries, do so properly as instructed by the local
government.
- Component Li fe :
(1) Battery---The internal calendar clock and CMOS RAM are backed by a Lithium primary
(2) BackLight--- LCD Panel backlight rating life is more than 50,000 hours.
(3) TouchPanel
(4) SD
* Replacement of expendables is handled as a repair (there will be a charge).
* Component life is not guaranteed value but only referential value.
battery.
The backup time at a temperature of 25°C with the power disconnected is 10 years or
more.
* Ambient temperature25°C±2°C, maximum brightness setting, up to
50% of the initial brightness decrease
---
The service life is 1 million operations or more.
* Load: 2.45N; speed: 2 times/second; pointed silicone rubber
implement
---
The SD card is used for the OS storage area. Use an SLC-type SD
card.
PT-40 User’s manual
5
1. Introduction
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
NOTE
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
About VCCI Class A and EMC Directive Class A secondary conditions
In order to comply with the above standards, attach the included ferrite core to the LAN
cable. To attach the ferrite core, open it, wrap the cable around the core once in a
location that is close to the connector, and then close the ferrite core.
FCC PART 15 Class A Noti ce
PT-40 User’s manu al
6
2. System Reference
Model
PT-40NVF-DC353111
CPU
ARM® Cortex-A8:600MHz
Main memory
On-board DDR3 SDRAM 256MB
Graphic
Controller
Built in CPU
Video RAM
Main memory shared
LCD type
LCD type
5.7 inch TFT color LCD,VGA(640 x 480), 260,000 colors
Backlight
LED metho d, ON/O FF software can control
Touch panel
Resolution
4096 x 4096 (emulated in 640 x 480 mode)
Detection method
Resistive-film analog type
Connection
Internal serial port
SD Memory card slot
1 slot, SD Memory card 512MB *1 Implemented OS installed
Serial I/F
RS-232C(generic) : 1ch (SERIAL PORT) 9pin D-SUB connector
Baud rate : 50 - 115,200bps [Connect only TX, RX, CTS, RTS]
LAN I/F
100BASE-TX / 10BASE-T, RJ-45 connector x 1
USB I/F
USB 2.0-compliant 1 port 1 *2
Keyboard, Mouse I/F
-*3
Watch dog timer
Software programmable, 255 level (1sec - 255sec)
Causes a reset up on time- out.
RTC/CMOS
The real-ti me clock is accu rate wi thin ±3 minutes (at 25°C) per month,
Lithium backup battery life : 10 years or more
Power
Power supply conn ector
12VDC *4
Input power supply
voltage
10.8 - 13.2VDC
Current consumption
12V 1A(Max.)
External device power
supply capacity
USB I/F : +5V 0.5° (500mA x 1)
Waterproofing and dust-proofing
Front part conforming to IP65 (Use attached packing)
Physical dimensions (mm)
182 (W) x 124 (D) x 38 (H) (Storage device isn't included)
Weight
About 0.8kg
2.
System Reference
Specifications
Table 2.1. Functional Specifications < 1 / 2 >
supply
*1: The disk capacities are values calculated with 1GB representing 1 billion bytes. The capacity that can be
recognized by the OS may be smaller than the actual capacity.
*2: When using a USB device, ensure that the cable length is 3m or less.
*3: Use the USB interface to connect a keyboard/mouse.
*4: Use a power cable shorter than 3m.
PT-40 User’s manual
7
2. System Reference
Model
PT-40NVF-DC353111
Operating temperature *5
0 - 50°C
Storage te mperatu re
-10 - 60°C
Operating humidi ty
20 - 85%RH(No condensation)
Floating dust particles
Not to be excessive
Corrosive gas
None
AC line / ±2kV ,*6
Signal line / ±1kV (IEC61000-4-4 Level 3, EN61000-4-4 Level 3)
Static
resistance
Vibration
resistance
Sweep
resistance
10 - 57Hz/ semi-amplitude 0.075 mm 57 - 150Hz/1.0G,
40min. each in X, Y, Z (JIS C60068-2-6, IEC60068-2-6- compliant)
10G, half-sine shock for 11 ms in x, y, and z directions
(JIS C60068-2-27-compliant, IEC68-2-27-compliant)
Grounding
Class D grounding, SG-FG / continuity
Standard
VCCI Class A, FCC Class A, CE Marking (EMC Directive Class A, RoHS Directive)
Paramete r
Condition
Min.
Typ.
Visual angle
φ = 180°
60deg
70deg
φ = 0°
60deg
70deg
φ = +90°
60deg
70deg
φ= -90°
70deg
80deg
Surface
Display in white
350cd/m
450cd/m
Contrast
ratio
(CR) =
Brightness at scr
een center w
ith white displayed
Brightness at sc
reen
center with black dis
played
Table 2.2. Installation Environment Requirements
Noise
resistance
Impact resistance
*5 For more details on this, please refer to chapter 3, “Installation Requirements”.
*6 When using AC adapter "PWA-36AWD1".
Line noise
electricity
Contact discharge / ±4kV (IEC61000-4-2 Level 2, EN61000-4-2 Level 2),
Atmospheric discharge / ±8kV (IEC61000-4-2 Level 3, EN61000-4-2 Level 3)
Display Optical Specifications
Table 2.3. Display Optical Specifications (PT-40NVF-DC353111)
(vertical)
Visual angle
(horizontal)
brightness
(at center)
* “Surface brightness” represents a numerical value per display. The expected brightness through a touch panel is
about 79% lower than the above value.
CR⊇10
Display.
Monochro
me
2
2
PT-40 User’s manu al
8
2. System Reference
DC Voltage
Acceptable Tolerance
+ 12VDC
+ 10.8 - 13.2VDC
L
ef
t
(
φ =
-
90
o
)
Z
Y
X
Top
( φ = 180
o
)
Right
( φ = 90
o
)
Bottom
( φ = 0
o
)
( θ = 0
o
)
Measurement direction
θ
Module
φ
CAUTION
Figure 2.1. Definition of viewable range
The above optical specification data shows optical characteristics of the liquid crystal in the display;
the data does not represent the actual view on the display or its viewing angles.
Power Requirements
Your system requires a clean, steady power source for reliable performance of the high frequency CPU
on the product, the quality of the power supply is even more important. For the best performance makes
sure your power supply provides a range of 12V DC power source.
Power Consumption
For typical configurations, the CPU card is designed to operate with at least a 36W power supply. The
power supply must meet the following requirements :
- Rise time for power supply: 2 ms - 30 ms
The following table lists the power supply’s tolerances for DC voltages:
Table 2.4. DC voltage tolerance
PT-40 User’s manual
9
2. System Reference
124
182
38
DC-IN
12V
100
110
10
10
4-M4
*1
[mm]
Physical Dimensions
PT-40NVF-DC353111
*1 Ensure that the mounting screw tips do not protrude past the surface to a depth of more than 15mm.
Figure 2.2 PT-40NVF-DC353111 Physical Dimensions
PT-40 User’s manual
10
3. Hardware Setup
C
AUTION
3. Hardware Setup
Before Using th e Product for the First Time
Follow the next steps to set up this product:
STEP1 By referring to the information in this chapter, install, connect and set this product.
STEP2 Connect cables.
Connect the cable of necessary external devices, such as keyboard and a mouse, to this
product using appropriate cables.
STEP3 Turn on the power.
Check once more that STEP1 and STEP2 have been carried out correctly, and
then connect the power cable to DC-IN. After power is supplied, the product
will start automatically. If you detect an error when the product is on,
immediately unplug the power cable from DC-IN, and then check whether
setup has been performed correctly. This product does not have a power switch.
Be sure to connect the keyboard and mouse to it before turning the power on for the first time.
PT-40 User’s manual
11
3. Hardware Setup
Hardware Set up
- Before you start, be sure that the power is turned off.
- Remove only those screws that are explained. Do not move any other screw.
Attaching of FG
(1) Use screws to attach th e FG.
Do not apply excessive force when tightening the screws.
* Use the mounting screws included with th e product. (M3)
Figure 3.1. Attaching the FG
Fastening the Cable
(The screws are attached to the product when it is shipped.)
Fastening th e U SB Cable
The system unit has a hole for attaching cable clamp. Using a cable clamp for a cable with lock-less
connector, such as the USB Cable, prevents the connector from being unplugged. Use the cable ti es and
cable clamps appropriately according to the connecting states and wiring directions of cables.
Figure 3.2. Attaching the cable clamp
PT-40 User’s manual
12
3. Hardware Setup
CAUTION
The FG pin of this product is connected to the GND signal of the DC power connector (DC-IN).
Note that the connection cannot be cut off.
Screw holes may be damaged if screws are tightened with a torque greater than the specified torque.
The specified tightening torque is 5 - 6kgf⋅cm.
PT-40 User’s manual
13
3. Hardware Setup
150
± 0.3
110
± 0.3
120
92
± 0.3
4-φ3.5
± 0.3
[mm]
Hardware Setup
(1) Cut out a panel according to the following dimensions to mount the main unit.
Figure 3.3. Dimensions o f Panel Opening
(2) Place the included waterproof packing between the main body and the panel, and then insert the
included waterproof screws from outside of the panel to fix the product in place.
Figure 3.4. Attaching the waterproof packing
PT-40 User’s manual
14
3. Hardware Setup
VESA Arm
C
AUTION
When using VESA standard 100mm mounting holes
The main body has mounting holes according to VESA standard 100mm. When using a VESA standard
100mm stand or the like, attach it as shown the following figure. (The dust proofing and waterproofing
specifications are not fulfilled when you attach the product to a VESA stand. )
Figure 3.5. Installation of VESA metal fittings
Ensure that the mounting screw tips do not protrude past the product surface to a depth of more
than 15mm.
PT-40 User’s manual
15
3. Hardware Setup
DC-IN
12V
0
°
-θ
+θ
45
°
CAUTION
Installation Requirements
Be sure that the ambient temperature is within the range specified in the installation environment
requirement by making space between the product and device that generates heat or exhaust air.
Installed angle which is recommended
Installed angle of this product which is recommended is -45° - +45°. Except for that, the temperature
specification of this product might not be filled.
Figure 3.6. Installed angle which is recommended
Note that even though the ambient temperature is within the specified range, an operational
malfunction may occur if there is other device generating high heat; the radiation will influence the
product to increase its temperature.
16
PT-40 User’s manual
3. Hardware Setup
DC-IN
12V
50mm
以上
50mm
以上
50mm
以上
50mm
以
50mm
以上
CA
UTION
Distances between this product and its vicinity
Figure 3.7. Distances between this product and its vicinity
Do not install this product into the fully-sealed space except the case in which the internal
temperature is adjustable by equipment such as air conditioner. Troubles such as operational
malfunctions could be occurred by the temperature increase caused by long-term usage.
PT-40 User’s manual
17
3. Hardware Setup
DC-IN
12V
38
50mm mor e
50mm more
[mm]
50mm more50mm more
Ambient temperature
In this product, the ambient temperature is decided from the multiple measurement points as shown
below. When making use of the product, the air current should be adjusted to prevent that all the
temperatures measured at the measurement points exceed the specified temperature. *1
Figure 3.8. Measurement points of ambient tempera tur e
PT-40 User’s manual
18
4. Each Component Function
Name
Function
USB
USB port connector
SERIAL
Serial port connector (9pin D-SUB/male)
DC-IN
DC power input connector
DC-IN
12V
LAN
USB
SERIA
L
DC-IN
4. Each Compone n t Fu nc t io n
Component Name
Figure 4.1. Componen t Na me
Table 4.1. Component Function
LAN Ethernet 100BASE-TX/10BASE-T RJ-45 connector
PT-40 User’s manual
19
4. Each Component Functi on
Connecto r type
9360-04P(mfd. by ALEX)
Pin No.
Signal name
1
GND
2
GND
3
12V
4
12V
4 3
2 1
Time
12V
V
oltag
e
2 -
30mS
DC Power Input Connec to r : D C-IN
To supply the power, always use the power supply listed below.
Rated input voltage : 12VDC
Range of input voltage : 10.8 - 13.2VDC
Power capacity : 12V 1.0A or more
Table 4.2. DC Power Connector
Applicable connector on the cable side
Housing : 9357-04(mfd. by ALEX) or 5557-04R (mfd. by MOLEX)
Contact : 4256T2-LF(AWG18-24) (mfd. by ALEX) or 5556 (AWG18-24) (mfd. by MOLEX)
Rise Time of Power Supply
Figure 4.2. Graph of Rise Time of Power Supply
PT-40 User’s manual
20
4. Each Component Function
LAN
Function
100BASE-TX
1
TX+
2
TX- 3 RX+
4
N.C.
5
N.C.
6
RX-
7
N.C. 8 N.C.
81
100M Ethernet : LAN
This product is equipped with 1 ports for 100M Ethernet.
- Network t ype : 100BASE-TX/10BASE-T
- Transmission speed * : 100M/10M bps
- Max. network path length : 100m/segment
Table 4.3. Fast Ethernet Connector
Pin No.
LEDs for display of network statuses:
Right LED : Link for LED
Normal connection : Orange ON
Operation : Orange Blinking
Left LE D : Operation check for LED
10M : Off
100M : Green
PT-40 User’s manual
21
4. Each Component Functi on
Pin No.
Function
1
USB_VCC
2
USB- 3 USB+
4
USB_GND
Connector used on
9-pin D-SUB (MALE)
Signal
name
4
1
1 5
9
6
N
o.4
-40
UNC
Inc
h s
cre
w
th
rea
ds
USB Ports: USB
This product is equipped with 1 port for USB 2.0 interface.
Table 4.4. USB Co nnector
Serial Port Interface: SERIAL
SERIAL (RS-232C Ports)
The product has 1 ports of RS-232C compliant serial ports supporting up to a baud rate of 115,200bps
with a 16-byte transm ission-dedicated d ata b u ffer and a 16-b yt e r ec ep t i on-dedicated data buffer.
Table 4.5. Serial Port Connector
the product
Pin No.
1 N.C Not connected -----
2 RD Received data Input
3 TD Transmitted data Output
4 N.C Not connected -----
5 GND Signal ground -----
6 N.C Not connected -----
7 RTS Request to send Output
8 CTS Clear to send Input
9 N.C Not connected -----
Meaning Direction
PT-40 User’s manual
22
5. Appendix
5. Appendix
Battery
Battery Specification
This product uses the following battery.
- Type : Lithium primary battery
- Model : CR2032
- Maker : HITACHI MAXELL
- Nominal voltage : 3 V
- Nominal capacity : 240mAh
- Lithium content : 1g or less
Removing the battery when disposing of the product
Before disposing of the product, follow the instructions given below to remove the battery.
(1) Remove the front cover.
(2) Remove the screws (in four locations) from the back of the product, and then remove
the back cover.
Remove the center battery connector, cut the cable tie, and then remove the battery.
Cut the cable tie.
Figure 5.1. Remo ving the bat te ry
Disposing the battery
Dispose the removed battery properly as instructed by local government.
PT-40 User’s manual
Remove the connector.
23
5. Appendix
PT-40 User’s manual
24
6. List of Options
6. List of Options
AC adapter
-
PWA-36AWD1
: AC adapter (Input: 100-240VAC, Output: 12VDC 3A)
PT-40 User’s manual
25
PT-40 Series
User’s Manual
PT-40NVF-DC353111
CONTEC CO.,LTD. December 2016 Edition
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Japanese http://www.contec.co.jp/
English http://www.contec.com/
Chinese http://www.contec.com.cn/
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD. [12022016]
[05262015] Managem en t N o. NA04124
[12022016_rev2] Parts No. LYSP282
Loading...