Contax i4R Operating Instructions
Introduction Getting Ready
Taking Pictures
Playback Set Up
Contents
A Important
BNote
• In this manual, the digital camera is referred to simply as "the camera". Also, SD memory
cards and MultiMedia cards are referred to generically as "memory cards".
This indicates important information that must always be observed
when using the camera.
These provide supplementary explanations or references to further
information on the same topic.
Introduction.................................................................... EN-6
FCC Compliance Statement for American Users ....................................... EN-6
Handling Precautions ................................................................................... EN-7
Caution and Warning Symbols............................................................................ EN-7
A World of Possibilities .............................................................................. EN-14
System Map ...................................................................................................... EN-15
Nomenclature .............................................................................................. EN-16
Names of the Menus and Icons Shown on the Screen............................ EN-19
"C" Still image, "M" Movie mode display ........................................................ EN-19
"P" Playback mode display.............................................................................. EN-21
LED Displays ............................................................................................... EN-23
Self-timer LED (red) .......................................................................................... EN-23
Card access LED (orange)................................................................................ EN-23
Caution LED (red) ............................................................................................. EN-24
Getting Ready............................................................... EN-25
Inserting the Battery Pack.......................................................................... EN-25
Removing the Battery Pack........................................................................ EN-26
Charging the Battery................................................................................... EN-27
Inserting the Memory Card......................................................................... EN-28
Write-Protect Switch *SD Memory Cards only ............................................. EN-29
Removing the Memory Card ...................................................................... EN-30
Turning the Camera On .............................................................................. EN-31
Turning the Camera Off .................................................................................... EN-31
Operating the camera after auto off .................................................................. EN-32
Viewing the battery level and charging guide ............................................... EN-33
Setting the Date and Time .......................................................................... EN-34
Date display format....................................................................................... EN-34
Using the Accessories................................................................................ EN-36
Using the USB Cradle ....................................................................................... EN-36
Attaching the Strap............................................................................................ EN-37
Using the Camera Case.................................................................................... EN-37
NEXT
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-1
Introduction Getting Ready
Taking Pictures
Playback Set Up
Taking Pictures ............................................................ EN-38
Taking Still Images...................................................................................... EN-39
Avoiding camera shake ................................................................................ EN-39
Holding the camera ...................................................................................... EN-40
Pressing the shutter release button half way................................................ EN-40
When the Memory Card is Full..................................................................... EN-41
Using Continuous Shooting Mode ............................................................ EN-43
Shooting Movies ......................................................................................... EN-46
[N] Setting the Frame Rate for Movies (frames per second) .......................... EN-48
Quickly Checking/Erasing Your Shots (Quick View) ............................... EN-50
Checking your images....................................................................................... EN-50
Erasing images ................................................................................................. EN-51
Selecting Scenes to Automatically Set the Focus and Flash ................. EN-52
Selecting the Scene Mode ................................................................................ EN-52
Cancelling Scene Modes .................................................................................. EN-54
Switching Between Macro and Landscape Mode ............................................. EN-55
Using Macro Mode ....................................................................................... EN-56
[k] Using the Self-Timer ............................................................................. EN-57
Using Zoom (Wide-angle and Telephoto) ................................................. EN-59
Using the Flash ........................................................................................... EN-60
Flash Modes...................................................................................................... EN-60
Setting the Flash Mode ..................................................................................... EN-61
Flash settings for each mode............................................................................ EN-62
Effective flash range ..................................................................................... EN-63
Adjusting the Brightness ........................................................................... EN-64
[M] Using Exposure Compensation .................................................................. EN-64
[ISO] Changing the ISO Sensitivity to Shoot Fast Moving Subjects ................. EN-66
[METERING] Selecting the Area Used for Setting the Exposure...................... EN-68
Setting the Focus ........................................................................................ EN-70
[FOCUSING] Selecting the Focusing Method ................................................... EN-70
Focusing Off-Center (Focus Lock) .................................................................... EN-72
Subjects That Are Difficult to Focus On........................................................ EN-73
[AF MODE] Still and Moving Subjects............................................................... EN-74
[V] Selecting the Number of Pixels ........................................................... EN-75
Guide to Selecting the Number of Pixels...................................................... EN-76
Adjusting Image Colors and Other Settings............................................. EN-77
[s] Selecting the Light Source (White Balance) ............................................. EN-77
Configuring white balance manually ................................................................. EN-78
[CHROMA] Changing the color intensity........................................................... EN-80
[SHARPNESS] Enhancing the Image Outlines................................................. EN-81
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-2
Introduction Getting Ready
Taking Pictures
Playback Set Up
Playback ....................................................................... EN-82
Viewing Still Images.................................................................................... EN-83
Viewing Your Images Enlarged......................................................................... EN-84
Viewing Image Information (File No/INFORMATION)....................................... EN-85
[O] Viewing Multiple Images...................................................................... EN-87
Displaying multiple images................................................................................ EN-87
Using the MULTI playback / GROUP playback screen ................................ EN-89
To return to normal playback (SINGLE playback)............................................. EN-90
Viewing Continuous Shooting Images...................................................... EN-91
Viewing Movies ........................................................................................... EN-93
[
o] Viewing Images Automatically as a Slideshow (Auto Play) ............. EN-95
[AUTO PLAY] settings....................................................................................... EN-95
Starting and Ending an [AUTO PLAY] Slideshow............................................. EN-98
[J]/[I] Erasing Unwanted Images ........................................................ EN-100
Erasing individual images (ERASE)................................................................ EN-100
Erasing a selection of images (SELECT AND ERASE) .................................. EN-101
Erasing all the images (ERASE ALL).............................................................. EN-103
[U] Protecting Images from Accidental Erasing (PROTECT).............. EN-104
Protecting an image ........................................................................................ EN-104
Unprotecting an image.................................................................................... EN-105
Tips for Erasing Images Using [PROTECT] and [ERASE ALL].................. EN-106
[p] Adding Sounds to Still Images (POSTRECORDING)........................ EN-107
Recording a message ..................................................................................... EN-107
Playing back a recorded message.................................................................. EN-109
Erasing a recorded message .......................................................................... EN-110
[V] Resizing and Trimming Images (RESIZE) ........................................ EN-111
Resizing an image........................................................................................... EN-112
Checking and erasing resized images ............................................................ EN-114
Resizing all the images ................................................................................... EN-115
Erasing all resized images .............................................................................. EN-117
[W] Rotating an Image .............................................................................. EN-118
[T] Using DPOF to specify print settings ............................................... EN-120
Specifying DPOF settings ............................................................................... EN-120
Specifying index print settings......................................................................... EN-122
Resetting all the DPOF print settings .............................................................. EN-123
[G] Printing by Connecting the Camera Directly to a Printer
(PictBridge)................................................................................................ EN-125
Connecting the camera to the printer.............................................................. EN-125
Specifying the print settings............................................................................ EN-127
Printing individual images ............................................................................... EN-129
Printing multiple images .................................................................................. EN-130
Printing using DPOF settings.......................................................................... EN-131
Ending PictBridge............................................................................................ EN-133
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-3
Introduction Getting Ready
Taking Pictures
Playback Set Up
Connecting to a Windows PC .................................................................. EN-134
Computer hardware and software requirements............................................. EN-134
Install the USB driver (Windows 98, Windows 98SE Only)............................. EN-135
Viewing images on a Windows PC ................................................................. EN-137
Memory card folder structure...................................................................... EN-139
Disconnecting the USB cable from a Windows PC......................................... EN-140
Deleting the Device (Windows 98 and Windows 98SE only) .......................... EN-142
Connecting to a Macintosh ...................................................................... EN-144
Computer hardware and software requirements............................................. EN-144
Viewing images on a Macintosh...................................................................... EN-145
Memory card folder structure...................................................................... EN-147
Disconnecting the USB cable from a Macintosh ............................................. EN-148
Connecting to a Television ...................................................................... EN-149
«Use the VIDEO OUT port to connect to the television» ................................ EN-149
«Playback on a television that supports D3 or higher video input»................. EN-151
Displaying Information (File No Display) ......................................................... EN-152
[W] Rotating an Image .................................................................................... EN-153
o] Viewing Images Automatically as a Slideshow (Auto Play)...................... EN-153
[
[U] Protecting Images from Accidental Erasing (PROTECT)........................ EN-156
[J] Erasing individual images (ERASE) ......................................................... EN-158
Set Up ......................................................................... EN-159
[AF MODE] Setting the AF method .......................................................... EN-160
[FORMAT] Initializing a Memory Card..................................................... EN-161
[BRIGHT CNTRL] Adjusting the LCD Monitor Brightness .................... EN-162
Setting the Date......................................................................................... EN-163
[DATE] Setting the Date and Time.................................................................. EN-163
[INSERT DATE] Adding the Date to Images................................................... EN-163
[POWER SAVE] Having the Camera Turn Off Automatically to
Save Power ................................................................................................ EN-165
Notes on using the power save function (in "C" or "M" mode) ................ EN-167
[BEEP] Adjusting the Volume of the Camera Button Beep................... EN-168
[SHUTTER VOL] Adjusting the Volume of the Shutter Sound .............. EN-169
[START SCREEN] Selecting the Startup Screen .................................... EN-170
To set the CONTAX logo screen (SINGLE/MULTI) ........................................ EN-170
To set a user-defined screen (SINGLE).......................................................... EN-171
To set a user-defined screen (MULTI) ............................................................ EN-173
Turning the startup screen off ......................................................................... EN-175
[REC REVIEW] Checking Images Right After You Shoot Them ........... EN-176
[ZLANGUAGE] Selecting the Menu Language.................................. EN-177
[VIDEO OUT] Setting the Output Format for a TV Connection ............. EN-178
[STARTUP MODE] Setting the Mode the Camera Starts In ................... EN-179
[DISPLAY INFO] Choosing the Information Displayed on the Screen
.... EN-180
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-4
Introduction Getting Ready
[FILE NO.] Starting Image File Numbers from 0001 ............................... EN-181
[MODE RESET] Resetting Function Settings ......................................... EN-183
List of Menu Items and Default Values ................................................... EN-184
Troubleshooting........................................................................................ EN-186
Problems and Solutions .................................................................................. EN-186
Messages and Responses.............................................................................. EN-189
Basic Digital Camera Glossary ................................................................ EN-191
Taking Pictures
Playback Set Up
Index........................................................................... EN-195
BACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-5
Introduction Getting Ready
Introduction
Taking Pictures
Playback Set Up
FCC Compliance Statement for American Users
DIGITAL STILL CAMERA CONTAX i4R
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Change the direction of the radio or TV antenna. Move the equipment or the radio or TV. For example, if the
equipment is to the right of the TV, move it to the left of the TV. Or, move the equipment farther away from the
radio or TV.
• Plug the equipment into a different outlet. Do not plug your radio or TV into the same circuit as your equipment.
• Ensure that all expansion slots (on the back or side of the equipment) are covered. Also, ensure that all metal
retaining brackets are tightly attached to the equipment.
• If these suggestions do not help, consult your equipment dealer or experienced radio/TV technician for help.
CAUTION
If you modify the camera in any way, without getting approval from KYOCERA CORPORATION, your camera
may violate FCC regulations. Violation of FCC regulations may cause the FCC to void your right to use the
modified camera.
Shielded cables must be used for this equipment to comply with the relevant FCC regulation.
For customers in Canada CAUTION
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
NEXTNEXT
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-6
Introduction Getting Ready
Taking Pictures
Playback Set Up
Handling Precautions
Caution and Warning Symbols
This Instruction Manual features the following caution and warning symbols to ensure that you use the camera
safely. Read the contents of these warnings carefully and use the corresponding features correctly.
F
DANGER
F
WARNING
F
CAUTION
This symbol indicates procedures which have a high likelihood of resulting in
death or serious personal injury if not followed properly.
This symbol indicates handling procedures which may result in death or
personal injury if not followed properly.
This symbol indicates procedures which may result in injury to the user, or
physical damage to the product if not followed properly.
<Precautions for Operating the Camera>
• If camera or batteries become hot, emit smoke or a burning smell, or display
other abnormal symptoms, remove them from the camera immediately to
prevent fire. When handling the batteries, take precautions to avoid being
burned.
• Never attempt to disassemble or modify the camera, since you may receive a
F
WARNING
severe electric shock.
• Do not operate the electronic flash at close proximity to a person’s eyes
(especially those of an infant), since eye damage may result.
• Do not attempt to take pictures while driving or walking since you may cause
an accident.
• When taking pictures, remain aware of your surroundings and what is
happening around you.
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-7
Introduction Getting Ready
• Clean the camera well after using it at the beach or other locations subject to
large concentrations of sand or dust. Salt air may promote corrosion of metal
components and damage or short circuits in electronic parts, causing the
camera to emit smoke or catch fire. Sand inside the camera may result in
internal damage and operating malfunctions.
• If the camera is brought quickly from a cold place to a warm room,
condensation may form on the lens and internal parts. Such condensation
may result in damage or short circuits in electronic parts, causing the camera
to emit smoke or catch fire. Whenever possible, avoid subjecting the camera
F
CAUTION
• This camera is not designed to be waterproof, and cannot be used in the rain or under water. If the camera
should inadvertently be exposed to water, it should be taken quickly to a Contax Service Center for
inspection.
• Take great care to keep the lens clean since soiling such as fingerprints can affect the accuracy of the
camera’s metering and focusing functions. If these areas become soiled and require cleaning, wipe them
gently with a third-party lens cleaning cloth. Any dust should be removed using a blower or lens brush.
• Clean the camera body by wiping with soft cloth. Never use benzene, thinner, or other volatile solvents or
cleansers, since such substances will damage the body materials.
• Do not remove the SD memory card or Multi-Media Card (MMC) while the card access LED is flashing.
• Interference may occur in recorded or played back images when the camera is used in areas subject to
strong electromagnetic interference (e.g., near a television set or stereo speakers).
• Do not direct the camera lens directly toward the sun when shooting, since the CCD element may be
damaged.
• If the camera is dropped, it may be damaged internally or parts may have been dislodged even when there is
no visible external damage. The camera must be taken to a Contax Service Center for checking.
• Do not attempt to touch the insides of the memory card slot, since damage or malfunction may result.
to sudden changes in temperature.
• This camera is a precision electronic instrument, and should be protected
from impacts and falls that might cause damage to internal parts or the
shorting of circuitry.
• This camera is an electronic device which uses a high-performance IC. The
heat emitted from the IC may make the camera hot during use. It is not a
failure.
• When taking the camera overseas or using it to record important events,
check its operating condition and take test pictures beforehand to
confirm proper operation.
Taking Pictures
Playback Set Up
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-8
Introduction Getting Ready
Taking Pictures
Playback Set Up
<Accessories>
For best performance, we recommend the use of genuine Contax accessories. Contax is not
responsible for any accidents or damage caused by the use of accessories made by other
manufacturers or fashioned by the user.
<Microcomputer Protection Circuit>
This camera incorporates a safety circuit to protect its microcomputer against strong external static
electricity. Though rare, it may fail to function because this safety circuit has come into action.
In this case, turn off the camera’s power, remove the batteries, reload them and use the camera
again.
<Storing the Camera>
• Store the camera in a well-ventilated location, avoiding damp or dusty areas,
drawers or boxes containing mothballs, or in laboratories or other locations
F
CAUTION
• Do not place the camera in places that may be exposed to high temperatures for extended periods of time
(the beach in summer, a closed car under bright sun, etc.). Such high temperatures may cause adverse
affects or damage to the camera, batteries, or memory cards.
• Remove the battery pack before storing the camera for extended periods of time, to prevent battery leakage
and resulting damage.
where chemicals are handled. Exposure to such chemical fumes can result in
damage to the camera’s circuitry, resulting in short circuits and causing the
camera to emit smoke or catch fire.
<LCD Monitor>
• Rubbing or pressing strongly on the LCD monitor screen can result in damage
or malfunctions. If there is dust or dirt on the LCD monitor, blow it off with a
blower brush. Heavy soiling should be wiped off using soft cloth.
• If the LCD monitor should become broken, take precautions to prevent
F
CAUTION
• Due to the innate characteristics of LCD panels, a few pixels may appear permanently lighted or may not light
at all. This is not a malfunction, and does not affect the recorded image in any way.
• The LCD monitor may appear difficult to see in some outdoor lighting situations.
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
personal injury from glass fragments.
• If the LCD monitor breaks and its liquid contacts your skin, quickly wipe away
any remaining liquid and wash the skin with soap and water. If the liquid
should enter the eyes, wash with clean running water for at least 15 minutes,
then seek medical attention immediately.
NEXTBACK
EN-9
Introduction Getting Ready
Taking Pictures
Playback Set Up
<Precautions for Handling Rechargeable Lithium Ion Battery
Pack BP-760S>
• Do not recharge or place batteries near sources of high heat (near flames,
heaters, or in direct sunlight, etc.), or in places exposed to flammable gasses,
since the batteries may generate heat, emit smoke, or rupture.
• Do not allow the positive (+) and negative (–) terminals of batteries to be
shortcircuited by metallic wires or object, since batteries may generate heat or
emit smoke or flames.
• Do not store batteries together with keys, necklaces, coins or other metallic
objects, since the objects may contact the battery terminals, causing shortcircuits.
• Do not try to heat batteries, or dispose of them in fire, since they may
F
DANGER
generate heat, emit smoke or flame, or rupture.
• Do not attempt to disassemble or modify batteries, since they may generate
heat, emit smoke or flame, or the internal battery liquid may enter your eyes,
causing blindness or other personal injury. If battery liquid should enter the
eyes, wash the eyes with clear running water and seek medical attention
immediately.
• This battery pack has been designed for exclusive use with this camera.
Always use the camera to recharge the battery pack. Do not use the battery
pack in any device other than this camera and do not attempt to recharge it
using a third-party charger as the battery pack may generate heat or smoke,
catch fire or explode.
• Never place batteries in a microwave oven or other container exposed to
high-voltage, since battery liquid may leak, or the battery pack may generate
heat, emit smoke or flame, or rupture.
F
WARNING
• Do not use leaking batteries. Battery liquid may contact your skin, causing
personal injury. In the event battery liquid does contact skin, wash
immediately with clean water.
• Do not use broken or ruptured batteries, since they may generate heat, emit
smoke or flame, or cause electrical shock.
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-10
Introduction Getting Ready
• Do not place batteries in water of any kind, or allow them to become wet,
since the batteries may generate heat, emit smoke or flame, or cause
electrical shock.
• Do not use or attempt to recharge wet batteries, since they may generate
heat, emit smoke or flame, or cause electrical shock.
• Do not store batteries in locations accessible to small children, since injury
could result.
F
CAUTION
• Even if the battery pack is fully charged, the amount of time that you will be able to use the battery pack will
be reduced if you use the camera in a cold environment. In this case, you should prepare yourself with a
reserve, pre-charged battery pack. To increase the usage time, put the battery pack in your pocket, etc. to
keep it warm, and only insert it in the camera immediately before taking a shot.
• When using the battery pack at normal temperatures, the battery can be used approximately 300 times. If the
number of shots that can be taken becomes extremely small, the battery has reached the end of its life. Place
an order for a new battery.
• Use the dedicated battery pack and cradle (included) for charging, and charge the battery at room
temperature (10°C - 35°C). If you charge the battery pack outside of the room temperature range, the battery
may take longer to charge and might not fully charge. Although it is possible to top up the battery, if you
continuously recharge a fully charged battery pack, battery performance will be degraded.
• When storing the battery pack, store it in a cool place. If you store the battery pack in an extremely hot or
extremely cold place, battery performance will be degraded.
• If you are not using the camera for a period of time, remove the battery pack from the camera. If the battery
pack is left installed in the camera, even if the camera is turned off, a small current will flow and the battery
will overly discharge. This can result in the battery becoming unusable.
• When you remove the battery pack from the camera, the date and time settings may be reset. If this
happens, you will need to reset these settings.
• When storing the battery pack, store the battery pack when the battery level is fully used (LOW BATTERY).
Furthermore, if you intend to store the battery pack for a long period of time, recharge and then discharge the
battery approximately once a year. (To get to the LOW BATTERY level, use the camera slideshow to run
down the battery.)
• If the battery pack terminals become dirty, clean the terminals by rubbing them.
• Do not throw batteries or subject them to strong impacts, since they may be
damaged and leak battery fluid.
• Whenever possible, use batteries at room temperature (20°C ± 5°C). The
battery capacity and usable time between recharging may be reduced in
situations of extreme heat or cold, such as during mid-summer or deep winter
weather, or when batteries are left in a hot location (e.g., inside a closed car
exposed to sun). Such conditions may also shorten the usable service life of
the battery.
• When not using batteries, store them in a cool, dry location.
Taking Pictures
Playback Set Up
Lithium-Ion Battery Pack.
Please recycle after its service life has finished.
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-11
Introduction Getting Ready
Taking Pictures
Playback Set Up
<Precautions for Using the AC Adapter AC-73L>
• Be sure that AC adapter plugs are connected securely before use. Loose plugs
and poor contacts can cause generation of heat, fire, and electrical shock.
• Do not attempt to modify the AC adapter’s cords, or subject them to
unreasonable force. Damage to the cords can cause fires and electrical
shock. If cords become so damaged that their wire cores are exposed,
discontinue use and consult your dealer or Contax Service Center.
• Do not attempt to remove covers, disassemble, repair or modify AC adapter,
since dangerous electrical shock could result.
• AC adapter plugs that have become laden with dirt or household dust should
F
WARNING
F
CAUTION
• Prolonged use may cause the AC adapter to feel warm; this is a normal phenomenon and not a malfunction.
• When not using the AC adapter for an extended period of time, first remove the plug from the USB cradle,
then disconnect the adapter from the AC outlet.
• If you wish to use the AC adapter while batteries are loaded in the camera, first set the camera’s power
switch to OFF, then connect the AC adapter before turning on the camera again.
not be used or approached with metal objects, since electricity might be
transmitted through the metal, causing fire or personal electrical shock. In the
event of heavy soiling of a plug, remove it from its outlet and clean away the
dirt before reusing.
• In the event that AC adapter plug emits smoke or unusual smell or sound, or if
it is damaged by impact or falling, cease use immediately. Continuing to use a
damaged plug could result in fire danger. In the event of damage to a plug,
consult your dealer or Contax Service Center.
• Do not connect the AC adapter to any sources of power other than a
household AC outlet (AC 100V to 240V; 50/60Hz). Using the adapter with
other voltages or ratings may cause the hazard of fire or electrical shock.
• Use only the dedicated AC adapter supplied with the digital camera. Using
other adapters may result in accidents and fire danger.
• Never attempt to splice the AC adapter cord, or subject it to severe twisting,
bending, or stretching. This may cause breakage or other damage to the
wires, resulting in a risk of fire or electrical shock. Plugging the cord into a low
capacity power outlet, etc. may cause a fire.
• Do not connect or disconnect the AC adapter with wet hands, since personal
electrical shock could result.
• Always grasp the plug body (not the cord) when removing the AC adapter
plugs from USB cradle and power outlet. Pulling on the cords could cause
breakage or other damage to the wires, resulting in danger of fire or electrical
shock.
• The AC adapter has been designed for exclusive use with this camera. To
prevent the danger of fire and electrical shock, do not use the adapter with
products other than the specific digital camera for which it was designed.
• If you notice any damage to the AC adapter, including broken wires or faulty
plug connections, stop using the AC adapter and consult your dealer or
Contax Service Center as soon as possible.
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-12
Introduction Getting Ready
Taking Pictures
Playback Set Up
Test Photos and Warranties
Make it a practice to take test shots before beginning any photography session to confirm that images are being
recorded properly. Contax will not be held responsible for failure of photographs to be recorded or transmitted to
a computer due to defects in the recording media (SD memory card or MultiMedia Card (MMC)).
Copyright Information
Photographs taken of professional performances, exhibitions, displays, or copyrighted materials may be used
only for your own personal enjoyment, and only with the consent of the copyright holders. Other use may
constitute violation of applicable copyright laws. Be aware that some performances, exhibitions, or displays
may impose restrictions on photographic or other recording even when the purpose of such recordings is
personal enjoyment.
• The SD logo is a registered trademark.
• MultiMediaCard
(MultiMediaCard Association).
• Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other
countries.
• Macintosh, Mac OS, QuickTime
Inc.
• Copyrights for PRINT Image Matching and PRINT Image Matching II are held by Seiko Epson Corporation.
• Adobe and Adobe Acrobat Reader are trademarks of Adobe Systems Incorporated.
• The DPOF trademark indicates that the product conforms to the specifications of the "Digital Print Order
Format (DPOF) for digital camera print information". Copyright for DPOF Version 1.00 is held jointly by
Canon Inc., Eastman Kodak Co., Fuji Photo Film Co., Ltd and Matsushita Electric Industrial Co., Ltd.
• All other corporate and brand names are the trademarks or registered trademarks of their respective owners.
TM
is a registered trademark of Infineon Technologies AG (Germany), licensed to MMCA
TM
, and the QuickTime logo are registered trademarks of Apple Computer,
PRINT Image Matching
* This product supports PRINT Image Matching II. When used in combination, PRINT Image Matching II-
enabled digital still cameras, printers and software help photographers to produce images that more faithfully
reflect the actual photography conditions and the intentions of the photographer.
PictBridge
* This camera supports PictBridge. By connecting this digital camera directly to a PictBridge-compatible
printer, you can select images on the camera's LCD monitor and start print jobs from the camera.
BACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-13
Introduction Getting Ready
Taking Pictures
A World of Possibilities
Zoom
When you are taking a picture, you can use
the digital zoom to enlarge the image by up
to 6x.
* Restrictions apply to the digital zoom for
some image sizes.
Continuous Shooting
This feature lets you shoot a rapid
sequence of photos at up to 3.0
frames per second.* This is useful
when you are taking pictures of a
moving subject or when you don't
want to miss a sudden photo
opportunity.
* When using a high-speed
memory card.
Playback Set Up
Flash
The camera's flash fires
automatically in dark conditions. But
you can also set the flash so that it
always fires, even in bright
conditions, or so that it never fires.
Focus Lock
Normally, the camera
automatically focuses on the
subject in the center of the
image. However, you can use
focus lock to have the camera
focus on a subject that is off to
one side of the image.
Scene Select
Scene Select provides a range of photography
modes you can choose from, with settings that
are optimized for particular scenes, such as
sporting events, portraits or nighttime scenery.
NEXTNEXT
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-14
Introduction Getting Ready
System Map
Taking Pictures
Playback Set Up
DPOF
-compatible
printer
Television that supports
D3 or higher video input
(Japan only)
(supplied accessory)
Card reader
D-connector
cable (thirdparty product)
USB Cradle
USB cable
accessory)
(supplied
Output
Memory Card
Digital camera
CONTAX i4R
USB cable
(supplied
accessory)
Print processing store
Video cable
(supplied accessory)
AC adapter AC-73L
(supplied accessory)
TV
PictBridgecompatible
printer
PictBridge
PC
Printer
Output
BACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-15
Introduction Getting Ready
Nomenclature
Taking Pictures
Playback Set Up
Shutter release button
Æ p.40
Lens
Lens cover
MENU button K 4-way button
Up : Flash F
Down : Macro/Landscape
LCD monitor
Speake r
OK button E
SCENE button I
Æ p.52
Left : Digital Zoom
Right : Digital Zoom
Continuous shooting
button N Æ p.43
Microphone
Self-timer LED
Flash unit
O
b
a
Caution LED
Mode select LED
Mode buttons
Card/battery cover
Æ p.25
Card access LED
(Reduces down to x1.0)
(Enlarges)
USB cradle connector
Strap lug Æ p.37
NEXT
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-16
Introduction Getting Ready
Taking Pictures
Playback Set Up
z USB Cradle
Use the USB cradle to charge the battery pack and to connect to a computer, printer, television or television that
supports D3 or higher video input (Japan only).
Camera connection
VIDEO OUT port
terminal
USB port
POWER IN port
D3 video output
terminal (Japan only)
z Camera Functions
You can access a wide variety of camera functions by pressing the mode buttons to change the camera mode.
The buttons on the LCD monitor unit offer a range of settings to suit photography in a variety of situations.
MENU button
You can change all kinds of
settings in still image mode,
movie mode, and playback
mode.
Flash
You can select from a range of
flash settings.
)
(Æ p.60
Macro/Landscape
Provides the optimal camera
settings for shooting close-up
subjects and distant scenery.
)
(Æ p.55
Shooting (Movies)
Shoot a movie to capture the
true feeling of being there.
You can also record sound
along with the movie.
)
(Æ p.46
Shooting (Still images)
The 4.0 megapixel highperformance CCD enables
you to shoot high-quality still
images. (Æ p.39
Playback
Displays recorded images on
the LCD monitor. Images can
also be resized and trimmed.
(Æ p.82
)
)
SCENE button
You can set the optimum
settings for your scene, such
as the Night View and the
Portrait mode.
)
(Æ p.52
Mode Buttons
Change between Movie
mode, Still image mode,
Playback mode and SET UP
mode.
SET UP
You can adjust various
settings, including AF (Auto
Focus) and LCD monitor
brightness. (Æ p.159
)
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-17
Introduction Getting Ready
Digital cameras also offer the user a range of other options, including connecting to a computer and getting
your images printed at a print processing store.
Connecting to a computer
Connecting your camera to a computer using the dedicated USB cradle and USB cable gives
you access to a wide range of uses for your images, including using image retouching software
to edit your images on a computer and sending them as attachments via e-mail.
* Windows 98 and Windows 98SE users must install the USB driver from the CD-ROM provided
with the camera. (Æ p.135
Digital printing
You can either print out your images directly on a printer or download them onto a memory card
and take them to your local print processing store for printing.
* Consult your local print processing store for details of the print services offered.
)
Taking Pictures
Playback Set Up
BACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-18
Introduction Getting Ready
Taking Pictures
Playback Set Up
Names of the Menus and Icons Shown on the Screen
"C" Still image, "M" Movie mode display
z Display in the normal screen
C Still image mode
qtu
!6
!7
10
!8
wer
+1.0
2272
ISO200X2.0
i
1234
CAF
+1
+1
o
!0
!1
!2
!4
M Movie mode
!5
!6
10
!8
uy
r
w
@4
00:00
+1.0
30fpsX2.0
CAF
@5
!0
!4
2004.10.21
!9 @0
@1 @2 @3
q Flash mode Æ p.60
w White Balance Æ p.77
e Metering mode Æ p.68
r Shooting mark
t Continuous shooting mode Æ p.43
y Movie mode Æ p.46
u Number of pixels Æ p.75
i Number of available shots
o ISO sensitivity Æ p.66
!0 AF mode Æ p.74
!1 Sharpness Æ p.81
!2 Chroma Æ p.80
!3
!9!3@0
2004.10.21
@2 @3
!3 Focus frame (MULTI AF) Æ p.70
!4 Focus frame (SPOT AF) Æ p.70
!5 Audio mark
!6 Macro/Landscape mode Æ p.55
!7 Scene mode Æ p.52
!8 Self-Timer Æ p.57
!9 Digital zoom Æ p.59
@0 Exposure compensation Æ p.64
@1 Camera shake warning
@2 Date
@3 Battery level indicator
@4 Before shooting: Available shooting time/
During shooting: Time shot
@5 Frame rate Æ p.48
NEXTNEXT
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-19
Introduction Getting Ready
Taking Pictures
Playback Set Up
z Display when the MENU button K is pressed
C Still image mode
EXP.COMP.
q w e r t
M Movie mode
PIXELS
q w !0 e r u
q SELF TIMER Æ p.57
w PIXELS Æ p.75
e EXP.COMP.
r WHITE BALANCE Æ p.77
t ISO
FOCUSING
yuio
y METERING
u FOCUSING
i CHROMA
o SHARPNESS
!0 FRAME/SEC Æ p.48
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-20
Introduction Getting Ready
Taking Pictures
Playback Set Up
"P" Playback mode display
z Display when the MENU button K is pressed
DISPLAY MODE
q w e r t
u
i
e
r
q DISPLAY MODE Æ p.87
w POSTRECORDING Æ p.107
e PROTECT Æ p.104 / p.156
r ERASE Æ p.100 / p.158
t ERASE MULTIPLE Æ p.101
ROTATE
* When playing back on a television that
supports D3 or higher video input.
(Japan only)
RESIZE
y u i o !0
RETURN
y RESIZE Æ p.111
u ROTATE Æ p.118 / p.153
i AUTO PLAY Æ p.95 / p.153
o DPOF Æ p.120
!0 PictBridge Æ p.125
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-21
Introduction Getting Ready
!
Taking Pictures
Playback Set Up
z Display when the 4-way button is pressed up
File No Display
(Press the 4-way button up once)
100–KICX0001.JPG
q
!3
!2
Information Display
(Press the 4-way button up twice)
INFORMATION
q
100–KICX0001.JPG 1600KB
e
2272X1704
1/125 F2.8 ± 0.3
y
ISO200
o
DPOF 1 PRTS
!0
2004.10.21 12:34:56
w
t
r
i
u
1
100–KICX_0001 2272X1704 2004.10.21 12:34:56
qe
!1
r
t
* When playing back on a television that
supports D3 or higher video input.
(Japan only)
q Folder numbers and file names Æ p.139
w File size
e Number of pixels (image size) Æ p.75
r Protection status
t Whether or not voice is used
y Shutter speed
i Exposure compensation Æ p.64
o ISO sensitivity Æ p.66
!0 DPOF settingsÆ p.120
!1 Photography date and time
!2 Continuous shooting mark
!3 Operating guide
u Aperture
* The continuous shooting mark indicates that the image was shot using continuous shooting (or AF continuous
shooting).
* The operating guide shows a guide to which buttons can be used on a screen.
BACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-22
Introduction Getting Ready
Taking Pictures
Playback Set Up
LED Displays
There are 3 LEDs on the camera. The LEDs indicate the status of the
camera by either lighting or flashing.
Self-timer LED (red)
While using the self-timer
Flashes
When a movie is being shot
When the shutter operates and shooting has ended (does not
light for continuous shots)
When the camera is set to Playback mode
When the camera is set to SET UP mode
Lights
When the camera is connected to a PC
Card access LED (orange)
Flashes while the camera is accessing the memory card, such
as recording images to memory card or reading files.
Do not open the card/battery cover or remove the memory card
while the LED is flashing as this could cause data corruption or,
in some cases, camera damage.
Flashes
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-23
NEXTNEXT
Introduction Getting Ready
Caution LED (red)
C
Still image
mode
M
Movie mode
Flashes rapidly
Flashes slowly
Taking Pictures
Take particular care to avoid camera shake
because a slow shutter speed is being used.
The flash is currently charging. Wait until the
light stops flashing before taking your next
shot.
Now recharging.
Playback Set Up
Battery pack
recharging
Lights
There is an error on the battery pack, AC
adapter or camera.
Flashes
BACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-24
Introduction Getting Ready
Getting Ready
Taking Pictures
Inserting the Battery Pack
1
Releasing the latch on the card/battery
cover.
qUse the pad of your finger to slide the card/battery cover in the
direction of the arrow until there is a click and the latch is released
(approximately 1 mm).
wThe bottom part of the card/battery cover opens (approximately
10 mm).
Playback Set Up
1
2
2 Open the card/battery cover.
ePull out the card/battery cover until it is stopped by the hinge.
rFully open the card/battery cover.
3 Insert the battery pack (BP-760S)
supplied with the camera.
Turn the battery stopper at the end of the battery pack in the direction of
the arrow while inserting the battery pack, as shown in the illustration.
A Important
• Insert the battery pack until the battery stopper
is securely locked (returns to its original
position).
• Be sure to insert the battery pack in the correct
direction, as inserting the battery pack the
wrong way around may cause damage.
4 Close the card/battery cover.
Push the card/battery cover into the opening in the camera surface
while you close it, then slide it in the direction of the arrow until it clicks
and locks.
Make sure the hinge does not lift up as you close the cover.
Hinge
Battery Pack Slot
Battery Stopper
3
Battery
Pack
A and B signs
Push against
the upper
surface.
4
NEXT
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-25
Introduction Getting Ready
Taking Pictures
Removing the Battery Pack
1
Check that the camera is switched off
and then release the card/battery cover
latch.
qUse the pad of your finger to slide the card/battery cover in the
direction of the arrow until there is a click and the latch is released
(approximately 1 mm).
wThe bottom part of the card/battery cover opens (approximately
10 mm).
Playback Set Up
1
2
2 Open the card/battery cover.
ePull out the card/battery cover until it is stopped by the hinge.
rFully open the card/battery cover.
3 Rotate the battery stopper to unlock the
battery pack.
When you turn the catch in the direction of the arrow, the battery pack
pops out a small distance.
4 Grasp the battery pack and pull it out of
the camera.
A Important
BNote
• Take care that you do not drop the battery pack.
The strong impact of dropping the battery pack
may cause it to heat up or leak battery fluid.
• Depending on the operating conditions of the
camera, the battery pack may heat up. Be
careful when removing the battery pack from the
camera.
If you do not intend to use the battery pack for a
long period of time, store it in a cool environment.
4
3
Hinge
Battery Stopper
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-26
Introduction Getting Ready
Taking Pictures
Charging the Battery
Playback Set Up
A Important
1
Place the camera in the USB cradle.
BNote
Ensure that the battery pack is inserted in the camera before charging.
Refer to "Using the USB Cradle" (Æ p.36) for
details on attaching the USB cradle.
2 Plug the AC adapter AC-73L into the USB
cradle to charge.
Charge time is approximately 3 hours.
Turn the camera off during charging.
The caution LED (red) turns on when the camera is charging, and turns
off after approximately 2 hours at which point the battery pack is 90%
charged.
Leaving the AC adapter connected for approximately one hour more
charges the battery pack fully.
A Important
BNote
• When you first purchase the camera, you need to charge the battery fully.
• If the battery pack is repeatedly charged with the battery pack or camera containing the
battery left in a hot location, the battery pack will deteriorate, reducing the number of
photos that can be taken. When this occurs, replace the battery pack with a new one.
• Remove the camera from the USB cradle and turn the power on to check the camera
battery level. (Æ p.33
The AC adapter supports voltages of up to 240 V. When you are charging the camera in a
foreign country, use the AC adapter cable that matches the voltage and power socket of
that country. You do not need to use a voltage transformer or other devices.
)
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-27
Introduction Getting Ready
Taking Pictures
Inserting the Memory Card
1
Check that the camera is switched off
and then release the card/battery cover
latch.
qUse the pad of your finger to slide the card/battery cover in the
direction of the arrow until there is a click and the latch is released
(approximately 1 mm).
wThe bottom part of the card/battery cover opens (approximately
10 mm).
Playback Set Up
1
2
2 Open the card/battery cover.
ePull out the card/battery cover until it is stopped by the hinge.
rFully open the card/battery cover.
3 Insert the memory card.
Insert the memory card with the labeled side facing the lens side of the
camera.
When inserting the card, push it into the slot until it makes a clicking
sound and stops.
A Important
• If the card does not slide in smoothly, the card may be upside down. Check that the
card is the right way up and do not try to force it into the slot.
• Do not attach stickers of any sort to the memory card as this may jam the card in
the slot so that you cannot remove it.
4 Close the card/battery cover.
Push the card/battery cover into the opening in the camera surface
while you close it, then slide it in the direction of the arrow until it clicks
and locks.
Make sure the hinge does not lift up as you close the cover.
Hinge
Cutout
Section
4
3
Memory
Card Slot
Labeled
Surface
Push against
the upper
surface.
BNote
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
Format the memory card in the camera before shooting to ensure the best possible
performance from the camera. (Æ p.161
)
EN-28
NEXTBACK
Introduction Getting Ready
Taking Pictures
Playback Set Up
Write-Protect Switch *SD Memory Cards only
SD Memory Cards come with a write-protect switch
(although some cards may not have this switch).
Sliding this switch downward prevents any more files from
being recorded onto the card and protects the images and
files already stored on it.
If a write-protected card is inserted into the camera in "C"
or "M" mode, "WRITE PROTECT" is displayed on the LCD
monitor.
You cannot take pictures or edit images using a write-
protected card. Note also that you cannot erase images
stored on the card or format the card.
Write-Protect
Switch
Slide this switch
down to writeprotect the card.
2272
0
WRITE PROTECT
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-29
Introduction Getting Ready
Taking Pictures
Removing the Memory Card
1
Check that the camera is switched off
and then release the card/battery cover
latch.
qUse the pad of your finger to slide the card/battery cover in the
direction of the arrow until there is a click and the latch is released
(approximately 1 mm).
wThe bottom part of the card/battery cover opens (approximately
10 mm).
A Important
The card access LED flashes when the camera is storing images in the memory card.
Do not open the card/battery cover or remove the memory card while this light is
flashing. Doing so may corrupt the files on the memory card, or even damage the
camera.
Playback Set Up
1
2
2 Open the card/battery cover.
ePull out the card/battery cover until it is stopped by the hinge.
rFully open the card/battery cover.
3 Push the memory card in gently with your
fingertip.
When the memory card is pushed in slightly, it pops back out and you
can then remove it.
4 Close the card/battery cover.
Push the card/battery cover into the opening in the camera surface
while you close it, then slide it in the direction of the arrow until it clicks
and locks.
Make sure the hinge does not lift up as you close the cover.
Hinge
4
3
Push against
the upper
surface.
NEXTBACK
Contents Glossary Index Nomenclature Menus and Settings Troubleshooting
EN-30
Loading...