CONTA-CLIP CMS-UI-2UI User Manual
CONTA-ELECTRONICS
IIIIsolated
solated SSSSignal
solatedsolated
Electrical specifications
Electrical specifications
Electrical specificationsElectrical specifications
Order inf ormation
Order inf ormation
Order inf ormationOrder inf ormation
type CMS-UI-2UI
cat.no 16121.2
Input dat a
Input dat a
Input dat aInput dat a
range (select via dipswitches) 0-5V/1-5V/0-10V/2-10V/0-10 mA/2-10mA/0-20mA/4-20mA
max. input signal (U / I) 12V / 25mA
input resistance (U / I) > 50 kOhm / 100 Ohm
Output da ta
Output da ta
Output da taOutput da ta
output signal (select via dipswitch) 0-5V/1-5V/0-10V/2-10 V/0-10mA/2-10mA/0-20m A/4-20mA (and inverted out)
max. output signal (U / I) < 10,5V / < 21mA
load resistance (U / I) > 1k Ohm / < 600 Ohm
offset (U / I) < 20mV / < 40uA
General d ata
General d ata
General d ataGeneral d ata
module power supply 24V DC ±25%
module current typical 65mA
conversion error < 0,5% of end value
temperature coefficient < 0,0 2 %/°C
max. conversion frequency 10Hz
CE marking Low Voltage Directive (LVD) 2006/95/EC, ac cording requirements of EN 61010
isolation voltage input / power 500V DC
isolation voltage input / output 500V DC
isolation voltage output / power 500V DC
operating / storage temperature 0°C…+55°C / -20°C…+70°C
conductor cross section 0,2 - 2,5 mm²
connection system screw clamp connection, pluggable
insulation stripping length 7 mm
mounting / installation position DIN-rail TS35 / any
module size LxWxH (TS35) 17,5 x 99 x 114,5m m
weight 115 gr
ignal converter
converter
ignalignal
converterconverter
EMC Directive 2004/108/EC, accordi ng requirements of EN 55011 and EN 6 1326-1
Manual
Manual
ManualManual
Features:
Features:
Features:Features:
• Multifunctional analog inputs (0..5V, 1..5V, 0..10V, 2..10V, 0..10mA, 2..10mA,
0..20mA, 4..20mA)
• Multifunctional analog outputs (0..5V, 1..5V, 0..10V, 2..10V, 0..10mA, 2..10mA,
0..20mA, 4..20mA). The output signal can be inverted.
• Analog signal range selectable via DIP switches
• Dual output 4-way galvanic isolation
• Power supply 24V DC
• Other analog signal ranges on request
The CMS-UI-2UI is a multi-functional dual output 4way isolated signal converter. This module is used for
electrical isolation and conversion of analog signals.
The 4-way isolation enables the module to be used
locally as well as in the vicinity of the controlling
system.
The inputs and outputs of the converter are configured
by means of dipswitches.
Any combination of input and output can be chosen,
so numerous different signal conversions can be set.
Default input/output setting is 0..10V / 0..10V.
Other default input/output settings on request.
CMS
CMS----UI
UI----2222UI
CMSCMS
UIUI
UI
UIUI
Cms-ui-ui manual rev0.fl.doc
Further information: www.conta-clip.com Cat. No.: 95121.7
Further information: www.conta-clip.com
Configuration
ConfigurationConfiguration
Configuration
Jumper /
Jumper / Jumper /
Jumper /
Dipswitch settings
Dipswitch settingsDipswitch settings
Dipswitch settings
CONTA-ELECTRONICS
IIIIsolated
solated SSSSignal
solatedsolated
To open the module press the locking levers under the terminals with a screwdriver.
Connecting the module
Connecting the module
Connecting the moduleConnecting the module
The pin configuration for I/O and power connection is shown on the top of the module.
Co
Connection diagram
nnection diagram
CoCo
nnection diagramnnection diagram
ignal converter
converter
ignalignal
converterconverter
The module is configured by setting the dip-switches according
to this manual and the table on the side of the module.
Voltage / Current Input selection via Jumpers
Voltage Input
CMS
CMS----UI
CMSCMS
Current Input
UI----2222UI
UI
UIUI
UIUI
Further information: www.conta-clip.com Cat. No.: 95121.7
Further information: www.conta-clip.com
Loading...