CONTA-CLIP CMS-F-UI User Manual
=
=
=
=
=
CONTA-ELECTRONICS
=====
=====IIIIsolated
solated S
==========
solatedsolated
Electrical specifications
Electrical specifications
Electrical specificationsElectrical specifications
=
Order in formati on
Order in formati on
Order in formati onOrder in formati on
type CMS-F-UI
cat.no 15886.2
Input da ta
Input da ta
Input da taInput da ta
range (select via dipswitches) 0-0,1Hz to 0-10kHz (see table)
max. input signal 30V
input resistance > 10 kOhm
sensor PNP/NPN, NAMUR initiator, push-pull
resolution 0,1mHz resp. 5 ppm from measur ed value
Output da ta
Output da ta
Output da taOu tput data
output signal (select via dipswitch) 0-5V / 0-10V / 0-20mA / 4-20mA
max. output signal (U / I) < 15V / < 30mA
load resistance (U / I) > 1k Ohm / < 600 Ohm
offset (U / I) < 10mV / < 20uA
response time 350ms + two times the period of the input fr equency
General data
General data
General dataGeneral data
module power supply 24V DC ±25%
module current Approx. 50mA
conversion error < 0,2%
temperature coefficient < 0,02 %/°C
CE marking Low Voltage Dir ective (LVD) 2006/95/EC, according require ments of EN 61010
isolation voltage input / power 1kV, 50Hz, 1min.
isolation voltage input / output 1kV, 50Hz, 1min.
isolation voltage output / power 1kV, 50Hz, 1min.
operating / storage temperature 0°C…+55°C / -20°C…+70°C
conductor cross section 0,2 - 2,5 mm²
connection system screw clamp connection, pluggable
insulation stripping length 7 mm
mounting / installation position DIN-rail TS35 / any
module size LxWxH (TS35) 17,5 x 99 x 114,5m m
weight 120 gr
Signal
ignal converter
ignalignal
converter
converterconverter
S S
EMC Directive 2004/108/EC, accord ing requirements of EN 55011 and EN 61326-1
===== = = = = = = = = =
Manual
Manual
ManualManual
=
=
Features:
Features:
Features:Features:
• Multifunctional frequency input (selectable from 0…0,1Hz to 0…10kHz)
• Multifunctional analog output (0..5V, 0..10V, 0..20mA, 4..20mA).
• Frequency input and analog signal output range selectable via DIP switches
• 3-Way galvanic isolation
• Power supply 24V DC
• Other analog signal ranges on request
=
The CMS-F-UI is a multi-functional 3-way isolated
signal converter. This module is used for electrical
isolation and conversion of frequency to analog
signals.
The 3-way isolation enables the module to be used
locally as well as in the vicinity of the controlling
system.
The inputs and outputs of the converter are configured
by means of dipswitches.
Any combination of input and output can be chosen,
so numerous different signal conversions can be set.
Default input/output setting is 0..1,0kHz / 0..10V.
=
Other default input/output settings on request.=
CMS
CMS----FFFF----UI
CMSCMS
UI=
UIUI
Cms-f-ui manual rev0.fl.doc
Further information: www.conta-clip.com Cat. No.: 95120.9
Further information: www.conta-clip.com
CONTA-ELECTRONICS
=====
=====IIIIsolated
solated S
==========
solatedsolated
Configuration
Configuration Dipswitch settings
ConfigurationConfiguration
=
=
Connecting the module
Connecting the module
Connecting the moduleConnecting the module
=
The pin configuration for I/O and power connection is shown on the top of the module.
=
Co
Connection diagram
CoCo
=
Signal
ignal converter
S S
ignalignal
nnection diagram
nnection diagramnnection diagram
converter
converterconverter
To open the module press the locking levers under the
terminals with a screwdriver.
The module is configured by setting the dip-switches according
to this manual and the table on the side of the module.
=
=
=
=
=
===== = = = = = = = = =
Dipswitch settings
Dipswitch settingsDipswitch settings
=
=
CMS
CMS----FFFF----UI
CMSCMS
UI=
UIUI
=
=
=
=
=
Further information: www.conta-clip.com Cat. No.: 95120.9
=
Further information: www.conta-clip.com
=
=
Loading...