Version 12/06
OPERATING INSTRUCTIONS
2-/4-channel hand-held
transmitter „FS20 S4“
Item no. 62 30 25
2
Introduction
Dear customer,
Thank you for purchasing this product.
This product meets the requirements of both current national and
European guidelines.
Please read the user manual completely and observe the safety and
operation instructions before using the product!
This user manual belongs to this product. It contains important
information specific to its operation and handling. Please bear
this in mind when passing on the product to a third party.
Therefore keep this user manual for future reference!
All company and product names contained herein are trademarks of
their respective owners. All rights reserved.
For more inquiries, contact or consult our technical service:
Germany: Tel. no.: +49 9604 / 40 88 80
Fax. no.: +49 9604 / 40 88 48
e-mail: tkb@conrad.de
Mon. to Thur. 8.00am to 4.30pm
Fri. 8.00am to 2.00pm
3
Table of contents
Page
1. Prescribed use ................................................................................. 4
2. Scope of delivery ............................................................................. 4
3. Explanation of icons ......................................................................... 4
4. Safety instructions ........................................................................... 5
5. Information on batteries/rechargeable batteries ............................ 6
6. Inserting the battery, replacing the battery .................................... 7
7. Control panel .................................................................................... 8
8. Operation .......................................................................................... 9
a) Basic functions (2-channel operation) ..................................... 9
b) Using several transmitters ...................................................... 10
c) Timer functions (2-channel operation) ................................... 10
d) Saving settings ........................................................................ 11
e) Restoring the factory settings ................................................. 12
9. Double number of channels (4-channel operation) ..................... 13
a) Switching between 2-channel and 4-channel operation ....... 13
b) Operation in the 4-channel mode ........................................... 14
c) Timer functions (4-channel operation) ................................... 15
10. FS20 address system basics ........................................................ 16
11. Programming the hand-held transmitter ....................................... 18
a) Setting the house code ............................................................ 18
b) Setting the addresses (2-channel operation) ........................ 19
c) Setting the addresses (4-channel operation) ........................ 21
12. Example of an address assignment ............................................. 22
13. Handling ......................................................................................... 24
14. Maintenance and cleaning ............................................................ 25
15. Disposal .......................................................................................... 26
16. Information on the range ............................................................... 27
17. Declaration of conformity (DOC) .................................................. 28
18. Technical specifications ................................................................ 28
4
1. Prescribed use
The sole purpose of the ‘FS20S4’ 2-/4-channel hand-held transmitter is to
remotely control the various components of the FS20 wireless control
system.
The components are remotely controllable on 2 channels (two buttons per
channel) or 4 channels (one button per channel).
Any use other than the one described above may damage the
product and cause other dangers.
Please read these operating instructions thoroughly and carefully, as they contain important information on operating and
handling the product.
2. Scope of delivery
• Hand-held transmitter
• User manual
3. Explanation of icons
The icon with an exclamation mark in a triangle points to
important instructions in this user manual that must be observed.
The ‘hand’ symbol indicates special tips and information on
operation.
5
4. Safety instructions
The product’s guarantee becomes invalid if the product is
damaged as a result of failure to observe these operating
instructions. We do not assume any liability for any resulting damages!
Nor do we assume liability for damage to property or
personal injury caused by improper use or failure to observe the safety instructions. In such cases the product’s
guarantee becomes invalid!
• For safety and licensing (CE) reasons any unauthorised alterations to
and/or modification of the product are not permitted.
• Do not use this product in hospitals or medical institutions. Although the
product emits only relatively weak radio signals, these may cause lifesupport systems to malfunction. This may also be the case in other
areas.
• Make sure that the product does not get damp or wet. Protect the
product against heat, cold, and direct sunlight while in storage or
operation.
• This product is not a toy. It should be kept out of the reach of children.
The product contains small parts, which may be swallowed (battery).
• Do not leave packaging material lying around. This may become a
dangerous plaything in the hands of children.
• Handle the product with care; knocks, blows or even a fall from a low
height can damage it.
6
5. Information on batteries/rechargeable batteries
• Keep batteries/rechargeable batteries out of the reach of children.
• Make sure that the polarity is correct when inserting the button cell (pay
attention to positive and negative pole).
• Do not leave batteries/rechargeable batteries lying around as they
could be swallowed by children or pets. In such case seek immediate
medical care.
• Leaking or damaged batteries/rechargeable batteries may cause acid
burns, if they come into contact with skin. Therefore, please make sure
you use suitable protective gloves.
• Make sure that batteries/rechargeable batteries are not short-circuited,
taken apart or thrown into fire. They might explode!
• Conventional batteries must not be recharged. They might explode!
• If the device is not used for a longer period of time (for example, when
stored), remove the battery to prevent it from leaking and causing
damage.
7
6. Inserting the battery, replacing the battery
• Open the battery compartment on the rear by turning the battery
compartment cover clockwise slightly using a coin (the arrows are in
the ‘open’ position).
• Insert a ‘CR2016’ lithium button battery, observing the correct polarity.
The plus (‘+’) pole has to point outwards towards you.
• Replace the battery compartment cover and close it by turning it
anticlockwise (position ‘closed’).
• If the LED on the front side of the hand-held transmitter does not light
up when you press the buttons or you find that the range of the handheld transmitter decreases, then you need to replace the old battery
with a new one.
Please also see section 8. d).
8
7. Control panel
A Control indicator/LED
1
Channel 1, ‘off’ button, or ‘dim down’
2
Channel 1, ‘on’ button, or ‘dim up’
3
Channel 2, ‘off’ button, or ‘dim down’
4
Channel 2, ‘on’ button, or ‘dim up’
The operation above describes the 2-channel operation of the
hand-held transmitter.
The buttons or functions are allocated differently for 4-channel
operation. This is described later on in the user manual.
12
34
A
9
8. Operation
Please note:
In the delivery state the components of the FS20 wireless
control system do not respond to remote control commands.
They must first be addressed according to the instructions
provided in the respective device’s user manual. The setting
of the basic functions is then possible.
a) Basic functions (2-channel operation)
Buttons are pressed quickly (to switch) or longer than 0.4 seconds (to dim).
Right button (
2
or
4
):
Quick press: ‘On’
Long press (>0.4 sec): ‘Dim up’
Left button (
1
or
3
):
Quick press: ‘Off’
Long press (>0.4 sec): ‘Dim down’
The control indicator/LED (A) briefly lights up to signal that a command has
been transmitted.
Now you can program and operate the basic functions of the
FS20 wireless control system components.
Also read the following subsections, if you require an extended system with several components or you wish to use the
additional functions.
10
b) Using several transmitters
In the delivery state each transmitter in the FS20 wireless control system
has its own, randomly set house code.
If you want to jointly control one or several receivers via different transmitters, you first need to coordinate the transmitters’ house codes.
The same house code must be set for each transmitter, as
described in section 11.
This must be set before programming the receivers for the
first time, as the associated house code is also sent to the
receiver during this procedure.
The transmitters’ channels are already set to the same addresses and only
need to be changed, if required (see sections 5 and 6).
c) Timer functions (2-channel operation)
In order to program a receiver’s timer function you must simultaneously
press the button combination that has been assigned to the receiver for
between 1 and 5 seconds (1 sec to 5 sec) on the hand-held transmitter.
This button combination is used to start as well as to stop the
programming of the timer. For information on how to program
the timer, see the instructions in the receiver’s user manual.
11
d) Saving settings
In the delivery state the ‘FS20S4’ has the following default settings:
House code: random
Address for channel 1: 11 11 (address group/subaddress)
Address for channel 2: 11 12 (address group/subaddress)
Address for channel 3: 11 13 (address group/subaddress)
Address for channel 4: 11 14 (address group/subaddress)
The addresses for channels 3 and 4 are, of course, only active
when the ‘FS20S4’ is switched to 4-channel operation. See
section 9.
You may make changes to the settings (as described in the respective
sections of this user manual), for example, setting the house code.
These settings are stored in a non-volatile memory and are
thus retained even when the battery is replaced.
If programming is not completed properly (if only some of the numbers are
entered when the house code is entered, for example), then the programming mode is automatically exited after one minute (control indicator/LED
stops blinking) and the entered numbers are ignored.
If the battery is weak (for example, the range of the ‘FS20S4’ is low), then
the programming may no longer be saved properly. You can tell that this is
the case, if the control indicator/LED remains lit for 3 seconds after the
programming has been carried out correctly.
For example, the control indicator/LED remains lit for 3 seconds after the
house code has been entered (normally it goes out!).
This also applies to other functions, for example, when switching from 2channel operation to 4-channel operation.
12
If this happens, then the programming that you have carried
out will not be saved. Replace the battery and then repeat the
programming.
We recommend that you replace the battery, if the LED lights up for 3
seconds, as described above.
e) Restoring the factory settings
To reset the ‘FS20S4’ to the factory settings, proceed as follows:
• Press the
2
and
4
buttons simultaneously for approx. 5 seconds
until the control indicator/LED briefly lights up.
• With the next press of any button a new random house code is
automatically generated and saved along with the other factory settings
and the ‘FS20S4’ is reset to the factory settings. See section 8. d).
13
9. Double number of channels (4-channel operation)
In addition to the standard 2-channel hand-held transmitter setting (for
example, two channels with an on/off button) the ‘FS20S4’ can also be
operated as a 4-channel transmitter.
Only one button is available to each channel, and there are no
more button combinations.
a) Switching between 2- and 4-channel operation
• Switching to a double number of channels (4-channel hand-held
transmitter):
Press the
2
and
3
buttons simultaneously for at least 5 seconds
(the upper right and lower left buttons on the hand-held transmitter).
The control indicator/LED on the hand-held transmitter blinks briefly to
confirm the setting. The hand-held transmitter is now in 4-channel
operation and each button now has its own channel.
• Switching to a normal number of channels (2-channel hand-held
transmitter):
Press the
1
and
4
buttons simultaneously for at least 5 seconds
(the upper left and lower right buttons on the hand-held transmitter).
The control indicator/LED on the hand-held transmitter blinks briefly to
confirm the setting. The hand-held transmitter is once again in the
normal 2-channel operating mode.
Please note:
Different operating and programming instructions apply when
a double number of channels has been set!
14
b) Operation in the 4-channel mode
In 4-channel operation each of the 4 buttons on the hand-held transmitter
has its own channel (compare with the figure in section 7):
1
Channel 1
3
Channel 3
2 Channel 2 4 Channel 4
For this reason operation is different than in the 2-channel mode. However,
switching and dimming functions are still available in 4-channel operation.
Proceed as follows:
• Switching
Pressing a button briefly (for fewer than 0.4 seconds) sends a switching
command.
The addressed receiver changes its switch state from OFF to ON or ON
to OFF, depending on which switch state was previously active.
• Dimming
If a button is pressed for longer then 0.4 seconds, a corresponding dim
up or dim down command is sent until the button is released (lamp is
dimmed up to the maximum and then dimmed down to the minimum,
and so on).
Here too, the dimming proceeds in the direction opposite to that of the
previously sent command, that is, if dim up was the last command, then
the next time the button is pressed a dim down command is sent.
The control indicator/LED (A) briefly lights up to signal that a
command has been transmitted.
15
c) Timer functions (4-channel operation)
In order to program a receiver’s timer function, proceed as follows:
• Press the button that is assigned to the receiver and keep it pressed (do
not release the button yet!).
• Press the button to the left, or right, for 1 to 5 seconds (1 sec to 5 sec)
and then release it. Only afterwards should you release the button that
you pressed first.
This procedure is used to start as well as to stop the
programming of the timer. For information on how to program
the timer, see the instructions in the receiver’s user manual.
16
10. FS20 address system basics
The FS20 wireless control system (to which the ‘FS20S4’ 2-/4-channel
hand-held transmitter belongs) works with its own ‘house code’.
This means that your neighbour can also use the same
wireless control system and the two systems will not interfere
with each other (provided that the house code has been
programmed differently).
256 different addresses can be set within a house code. These addresses
are divided into 4 address types (available number is in brackets):
• Single addresses (225)
• Function group addresses (15)
• Local master addresses (15)
• Global master address (1)
One address from each address type can be assigned to each receiver.
This means that each receiver can respond to up to 4 different addresses,
but only ever to one address per address type.
If you need a receiver to respond to more than one transmitter, you can
program the transmitters to the same address or, if different transmitter
address types have been set, you can program the receiver consecutively
to these different addresses.
The individual address types have the following function:
• Single addresses
Each receiver should be set to a single address so that it can be
controlled separately.
17
• Function group addresses
Several receivers are defined as a functional unit by being assigned to
a function group address. If, for example, all the lamps in a house are
assigned to a function group, then all the lamps in the entire house can
be switched on or off by pressing one button.
• Local master addresses
Several receivers are spatially defined as one unit and controlled via
the local master address. If, for example, all the receivers in a room are
each allocated to a local master address, then all you need to do is
press one button when leaving the room to switch off all the consumer
loads in the room.
• Global master address
Several receivers are assigned to the global master address and are
jointly controlled via this address. All the consumer loads can easily be
switched off simply by pressing one single button when leaving a
house, for example.
This address system opens up a variety of possibilities. You can even
implement access authorisations; by assigning three garage doors to
different single addresses and a joint function group (‘Garage doors’), for
example.
Several people can then each be given a hand-held transmitter with a
relevant single address for one garage door, while all the garage doors can
be opened via a hand-held transmitter with a programmed function group
address or all the doors can be automatically closed in the evening via an
FS20 timer.
The various address types and addresses are only set on
the transmitter and these settings are transmitted to the
receivers via the address assignment.
18
11. Programming the hand-held transmitter
The house code, an address group and a subaddress are used for coding
the transmitters and their individual buttons. You can also use special
address group assignments to program the hand-held transmitter as a local
or global master.
To set the addresses and codes, the 4 buttons on the hand-held transmitter
are used, which have the numbers 1, 2, 3 and 4.
1
Number ‘1’
3
Number ‘3’
2 Number ‘2’ 4 Number ‘4’
a) Setting the house code
Once the battery has been inserted the hand-held transmitter
selects a random house code.
To choose your own house code, proceed as follows:
• Keep both left buttons on the hand-held transmitter (buttons
1
and
3
) pressed for 5 seconds until the control indicator/LED (A) begins
to blink every second.
• Now use the 4 buttons to enter your system’s 8-digit house code. This
must be identical for all the remote control transmitters in the same
system (as a precaution, make a note of this code and keep it safe!).
Example: 23141342
• The programming mode ends automatically once you have entered the
eighth digit. The control indicator/LED (A) goes out.
19
b) Setting the addresses (2-channel operation)
A channel’s address comprises a 2-digit address group and a 2-digit
subaddress.
Example: 1131, address group 11, subaddress 31
The address group ‘11’ is factory set for both channels.
Subaddress ‘11’ is pre-programmed for channel 1 and
subaddress ‘12’ is pre-programmed for channel 2.
Channel: 12
Address: 11 11 11 12
If several transmitters are to be operated at the same time and control
different receivers, then different addresses need to be set on the transmitters.
1. Setting a single address (address group/subaddress)
• Press both buttons of the respective button combination simultaneously for at least 5 seconds (for example, the buttons
1
and
2
for
channel 1).
The control indictor/LED (A) now blinks every second.
• Enter a 2-digit address group and a 2-digit subaddress using the
1
,
2, 3
and
4
buttons.
Example: 1431 (address group 14, subaddress 31)
• The programming mode ends automatically once you have entered the
fourth digit. The control indicator/LED (A) goes out.
Please note:
The address group 44 and the subaddress 44 both have a
particular meaning (see the following item)!
20
2. Assigning function groups and master addresses
• Function groups (44xx)
If you enter 44 as the address group, then the subaddress (provided this
is not also set to 44; see the following section) is defined as a function
group. 15 different function groups between 4411 and 4443 can then be
defined.
The following are possible: 4411, 4412, 4413, 4414, 4421,
4422, 4423, 4424, 4431, 4432, 4433, 4434, 4441, 4442, 4443
• Local master (xx44)
If you only set the subaddress to 44, then this channel functions as a
local master within the set address group. All receivers that are programmed with this local master address are controlled simultaneously.
The following are possible: 1144, 1244, 1344, 1444, 2144,
2244, 2344, 2444, 3144, 3244, 3344, 3444, 4144, 4244, 4344
• Global master (4444)
If you set the address group and subaddress of a channel to 44, then
this channel functions as a global master. All receivers that are programmed with this global master address are controlled simultaneously.
The only global master is 4444.
21
b) Setting the addresses (4-channel operation)
If the ‘FS20S4’ is operated in the 4-channel mode, proceed as follows in
order to change the address group and subaddress of the respective
button:
• Press and hold the button to be programmed.
• Now also press the button next to it. Keep both buttons pressed
simultaneously for at least 5 seconds!
• Wait until the control indicator/LED (A) blinks every second indicating
that the programming mode is activated.
• Enter a 2-digit address group and a 2-digit subaddress using the
1
,
2, 3
and
4
buttons.
Example: 1112 (11 = address group, 12 = subaddress)
• The programming mode ends automatically once you have entered the
fourth digit. The control indicator/LED (A) goes out.
22
12. Example of an address assignment
When you require a large, extended system, it is advisable to select
addresses systematically so that you have an overview of the addresses
that have already been assigned and so that you can jointly control the
programmed receivers simply and logically in groups.
1111
1144
4411
4444
1122
1144
4444
1131
1144
4444
1211
1212
4411
4444
1311
4411
4444
1411
4411
4444
1412
4444
A
B
C
D
Global
master address
4444
Local
master address
e.g. 1144
House code, e.g.
1234 1234
Function group 44xx
e.g. 4411 ceiling lamps
A different address group has been assigned to each room:
• Room A: 11
• Room B: 12 (the awning is also assigned to room B)
• Room C: 13
• Room D: 14
23
15 address groups are possible:
11, 12, 13, 14, 21, 22, 23, 24, 31, 32, 33, 34, 41, 42, 43
In order to be able to separately control each receiver, you need to program
each receiver to a single address. In addition to the address group that is
already selected (room A: 11, room B: 12, room C: 13, room D: 14), a
subaddress is also needed.
The following 15 subaddresses are possible for each address
group:
11, 12, 13, 14, 21, 22, 23, 24, 31, 32, 33, 34, 41, 42, 43
In the example the awning is programmed to the single address 1211,
which comprises the address group 12 and its subaddress 11.
All the receivers in room A have also been programmed to a local master
address (1144 in the example).
For the local master address 44 is always set as the subaddress,
while one of the 15 local master addresses (11, 12, 13, 14, 21,
22, 23, 24, 31, 32, 33, 34, 41, 42, 43) can be selected via the
address group.
Example: 1144, address group 11, subaddress 44
All the lamps in the house can be controlled via the global master address
4444.
The awning was deliberately not programmed to this address and can
therefore only be addressed via its single address (1211). It must be
operated separately in this example.
The ceiling lamps in all the rooms are also combined in a function group
(4411 in the example, address group 44, subaddress 11) and can therefore
be jointly controlled.
To select one of the 15 function groups, you need to set 44 as the address
group and a value between 11 and 43 (11, 12, 13, 14, 21, 22, 23, 24, 31, 32,
33, 34, 41, 42, 43) as the subaddress.
24
13. Handling
The product must not be opened or taken apart (apart from when replacing
the battery, as described in this user manual).
There are no serviceable parts inside the product. The licence (CE) and the
guarantee/warrantee become invalid, if you open the device or take it apart.
Avoid the following unfavourable ambient conditions when operating or
transporting the device.
• Moisture or excessive air humidity
• Extreme cold or heat
• Direct sunlight
• Dust or flammable gases, vapours or solvents
• Strong vibrations
• Strong magnetic fields such as those found near machines or loudspeakers
Never use the product immediately after it has been brought from a cold
room into a warm one. The condensation water generated could destroy the
product.
Wait until the product has reached room temperature. This can take
several hours.
The buttons on the hand-held transmitter may be inadvertently pressed
when transporting it in a bag or pocket (for example, if it is attached to a key
chain). This may cause switching operations to be triggered or its programming mode to be accidentally activated.
The product should be kept out of the reach of children as it contains parts
that could be swallowed. Make sure that children cannot access it.
Even a fall from a low height can damage the product.
25
14. Maintenance and cleaning
The product requires no servicing except for battery replacement. Repairs
or maintenance work should only be carried out by a skilled technician.
Clean the product with a soft, clean, dry and lint-free cloth.
To remove heavier dirt, use a cloth which is slightly moistened with
lukewarm water. Do not use solvent-based cleaning agents, as these may
damage the surface of the plastic casing and its inscription.
26
15. Disposal
a) General information
When the product is no longer usable, dispose of it in accordance with the applicable statutory regulations.
b) Batteries and rechargeable batteries
As the consumer, you are legally obliged to return all your used batteries
and rechargeable batteries. Do not dispose of your used batteries via
the household rubbish!
Batteries/rechargeable batteries containing harmful substances are marked with the following icons, which alert you to
the fact that disposal via the household rubbish is prohibited.
The identifiers for the respective heavy metals are:
Cd=cadmium, Hg=mercury, Pb=lead (the designation is writ-
ten on the battery/rechargeable battery, for instance, under
the rubbish bin icons depicted at the left).
You can return your used batteries/rechargeable batteries
free of charge to any authorised disposal station in your area,
in our stores or in any other store where batteries/rechargeable batteries are sold!
By doing so you comply with your legal obligations and also make a
contribution to environmental protection.
27
16. Information on the range
• The FS20 wireless control system, including the ‘FS20S4’ hand-held
transmitter, works in the 868 MHz range. This range is also used by
other devices and radio services.
This means that devices that operate on the same or neighbouring
frequency may restrict both the operation of the ‘FS20S4’ and its range.
• The specified range of up to 100m is the so-called free-field range. This
describes the range where there is direct visual contact between the
transmitter and the receiver.
In practice, however, walls, ceilings, etc. between the transmitter and
the receiver may affect and reduce the range.
Other causes of reduced ranges:
• All types of high-frequency interference
• Any buildings or vegetation
• Conductive metal parts that are located near the devices or within or
near their transmission path, for example, radiators, metallised insulation glass windows, reinforced concrete ceilings and so on.
• Influence on the radiation pattern of antennas due to the distance from
the transmitter or receiver to conductive surfaces or objects (also to
human bodies or the ground)
• Broadband interference in urban areas that reduces the signal-to-noise
ratio; the signal is no longer recognised due to this ‘noise’
• Interference radiation resulting from insufficiently shielded electronic
devices, for example, operating computers or similar
28
17. Declaration of conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Straße 1, D_92240 Hirschau (Germany), hereby declare that this product complies with the fundamental
requirements and other relevant regulations of directive 1999/5/EG.
You can find the declaration of conformity for this product at
www.conrad.com.
18. Technical specifications and features
Voltage/power supply: ............................ Lithium button battery ‘CR2016’
Transmission frequency: ....................... 868.35MHz
Modulation: ............................................. AM
Range: ..................................................... Up to 100m (free-field)
Dimensions (W x H x D): ....................... 41mm x 11mm x 52mm
29
30
31
Imprint
These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str.
1, D-92240 Hirschau/Germany.
No reproduction (including translation) is permitted in whole or part e.g. photocopy,
microfilming or storage in electronic data processing equipment, without the express
written consent of the publisher.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© Copyright 2006 by Conrad Electronic SE. Printed in Germany.
100%
recycling
paper.
Bleached
without
chlorine.
CONRAD IM INTERNET http://www.conrad.com
CONRAD IM INTERNET http://www.conrad.com
http://www.conrad.com
Loading...