Page 1
CardBus Fast Ethernet
Attached Port PC ard
USER’S MANUAL
Page 2
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply
with the limits of a Class B computing devices,
pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
If you suspect this product is causing interference,
turn your computer on and off while your radio or TV
is showing interference. If the interference
disappears then when you turn the computer off and
reappears then you turn the computer on, something
in the computer is causing interference.
You can try to correct the interference by one or more
of the following measures:
1. Reorient/Relocate the receiving antenna.
2. Increase the separation between the equipment and
receiver.
3. Connect the equipment into an outlet on a circuit
difference from that to which the receiver is
connected.
4. Ensure that all expansion slots (on the back or side
of the computer) are covered. Also ensure that all
metal retaining brackets are tightly attached to the
computer.
Page 3
1. Introduction
Thanks you for purchasing our 10/100Mbps
CardBus Fast Ethernet Adapter. This guide is to
provide the installation and usage of this adapter
an IEEE 802.3/802.3u standard fast Ethernet network.
CardBus-Compliant notebooks. This adapter takes u
full advantage of the power of high performance,
32-bit architecture mobile PCs.
full-duplex, the notebook is connected to a switch on
a dedicated segment. With transmission and reception
taking place simultaneously, data transfer is double.
CardBus slot. And your notebook PC will be up and
running on the network. That’s all you need to do.
Not a tool is necessary, not configuration setting is
required.
Windows 98/98SE, Windows NT 4.0,
Windows2000/XP and other popular operation
systems. Whatever your requirement are ease of
installation, superior performance or responsive
support backed up by unlimited technical support,
this adapter is the superior choice.
for network installers and users.
The Cardbus Fast ethernet Card is credit card
size network adapter that connects a notebook to
This is designed for Type II and Type III PCMCIA/
Full/half duplex operation is auto-detected. In
Simply plug in this adapter to your notebook’s
This adapter can working with Windows 95,
Page 4
2. Features & Specifications
1. Features & Benifit
Complies with IEEE 802.3 10BaseT and 802.3u 100Bsae TX
standards.
Automatically negotiates 10 or 100Mbps connection rate,
depending on speed of the network.
32-bit CardBus architecture brings the highest performance.
Complies to PC Card CardBus Standards.
Provides full-duplex to enhance throughput.3V low power
consumption.
Compatible with all notebook PCs that comply with the PC Card
standard.
2. Technical Specification
Standards: IEEE 80.2.3 10BaseT and 802.3u 100BaseTx
Connector: RJ-45 Dongless Design
Bus Width: 32-bit CardBus
PC Interface: PC Card CardBus Standards
LED:10M, 100M
Driver Support: ODI- Novell Netware 3.x/4.x
Temperature:0 ﾟ to 50 ﾟ
Humidity: 10% to 90%
Certification: FCC Class B, CE Mark
NDIS- Windows95/98/NT4.0/2000/XP
Page 5
3. Installation
This chapter describes how to install your CardBus Card.
(1) Hardware Installation
Hold the Card label up and insert the card into the notebook
PCMCIA/CardBus slot with 68 pin connector facing the
notebook.
(2) Software Installation
The drivers and utilities are supplied by the CD-ROM included
in this product. For detail description. Please refer to document
in the CD-ROM provides by this product.
4. Trouble Shooting
If you experience any problems with the PC Card, first make
sure the appropriate driver is loaded, the proper cable is
connected to the PC Card and the hub complies with the
adapter specification, then check the LED.
The PC Card provides two LEDs to indicate network status.
(1) 10M
This LED indicates the connection speed in 10Mbps. When
the light is on, it indicates that the 10Mbps connection is
established. When the light is blink, it indicates that the
packets are transmission.
(2) 100M
This LED indicates the connection speed in 100Mbps. When
the light is on, it indicates that the 100Mbps connection is
established. When the light is blink, it indicates that the
packets are transmission.
Loading...