Conergy PH Series, PH 220-255P, PH 175-200M, PH 230-260M BL User Manual
Conergy PH Series Modules
Solar module user manual
1 Introduction
1.1 Short description
Conergy PH modules are solar modules for installation in photovoltaic systems.
1.2 About this manual
1.2.1 Subject of this manual
The subject of this manual is the installation and electrical connection of the Conergy PH module in a photovoltaic system.
This manual applies to the following modules: Conergy PH 175-200M, Conergy PH 220-255P, Conergy PH 230-260M BL.
1.2.2 User group
The manual is intended to be used by the system owner and by qualied persons possessing technical skills and basic
electrical, electronic and mechanical knowledge related to photovoltaic systems. Please retain this manual for future
reference.
1.2.3 Symbols
Start of a step-by-step procedure with description of the goal of the procedure. Individually numbered steps
follow, which may be interrupted by background information, illustrations, or warnings.
Background and additional information or the status of a procedure. Appears between the steps of a procedure,
within the sequence/ course of a procedure.
Denotes a hazardous situation. Disregard of this instruction may lead to slight or moderate injury.
Denotes an extraordinarily hazardous situation. Disregard of this instruction may lead to serious, irreversible
injury or death.
1.3 Standards and technical directives
Conergy PH modules comply with the following standard:
| ULC/ORD-C1703-01 & UL 1703
1.4 Intended use
Conergy PH modules are designed for use in photovoltaic systems. Any other use is deemed to be not as intended.
Intended use also includes compliance with the specications stated in this installation manual. Conergy shall not be held
liable for damages arising from a failure to observe and follow the installation manual, particularly the safety instructions,
or from any improper use of the product.
2 Safety
2.1 Responsibilities of the owner/operator
Installing solar photovoltaic systems may require specialized skills and knowledge. The system operator has safety-related
responsibilities, and must ensure that:
| locally applicable standards and directives are complied with;
| the installation is performed by qualied persons;
| those commissioned to perform the work can evaluate their assigned tasks and recognize possible risks;
| those commissioned to perform the work are familiar with the system components;
| the installation manual is available during the installation;
| the installation manual is an integral part of the product;
2
| the installation manual, and in particular the safety instructions, have been read and understood by the relevant
personnel before installation;
| suitable lifting gear and tools are used for the installation;
| if replacements are required, only Conergy components are used and repairs are carried out only by qualied persons,
otherwise the warranty will expire;
| only components (cable, plugs, mounting parts, etc.) that are suitable for use in photovoltaic systems are used;
| the module is not installed near highly ammable gases or vapors because sparks could be generated;
| sunlight is not articially concentrated on the solar module;
| no paint, coatings or stickers are applied to the module;
| the module is not dismantled and none of the parts provided on delivery are removed.
2.2 Basic safety instructions
The following safety instructions and warnings form an essential part of this manual and are of fundamental importance
when handling this product.
| Solar modules produce electrical energy when exposed to light. Even a single module produces enough voltage and
current to cause shocks and burns if safety precautions are not followed. The shock hazard increases as modules are
connected in series (producing higher voltages), and in parallel (producing higher current).
| Make allowance for the loads that the Conergy PH modules may generate for the entire structure. The modules have
been evaluated by UL for a maximum positive design loading of 5400Pa/113lbs/ft
| In order to prevent damage (e.g. breakage of glass), never leave Conergy PH modules unsecured.
| Check Conergy PH modules for mechanical integrity before installation. Use only undamaged modules.
| Use only mounting systems that can withstand the expected loads for snow, wind, etc. The modules have been
evaluated by UL for mounting using the 4 provided mounting holes in the frame.
| Make sure that no other system components will impair the mechanical or electrical function of the Conergy PH
modules.
| Do not drill holes in the module frame or in the glass surface and do not carry out any welding work on or near the
Conergy PH modules.
| Comply with the applicable occupational health and safety regulations.
| Wear suitable clothing and gloves and remove metallic jewelry to prevent accidental contact with energized
components.
| The presence of a second party who can provide help in the event of an accident is recommended during the entire
installation process.
| Ensure a copy of this installation manual is provided to the system owner.
2
.
3 Installation
3.1 General installation instructions
| Make sure that all locally applicable standards, construction regulations and accident prevention regulations are
complied with.
| The module must be installed in accordance with National Electrical Code (NEC) in the US and in accordance with
Canadian Electrical Code Part I (CEC) in Canada.
| We recommend the Conergy SunTop mounting system for installations on sloping roofs. The recommended stand-off
height is 115mm.
| Select an installation location with the maximum sunlight at all times of the year. Avoid shaded areas.
| In northern latitudes, orient the photovoltaic modules to the south. Determine the ideal setting angle according to the
latitude of the installation location. Request this information from your dealer or nd it in the ofcial tables.
| You can nd further installation instructions in the installation manual for the relevant mounting system.
| The photovoltaic modules are bolted or clamped in place depending on the design of the mounting system. The
mounting structure must be made from material that is resistant to corrosion and atmospheric conditions and able to
withstand the loads required.
3
Loading...