Condux Fiber Optic Cable Puller Hitch Mount User Manual

Limited Warranty

USER GUIDE USER GUIDE USER GUIDE

Condux International, Incorporated extends the following warranty to the origi­nal purchaser of these goods for use, subject to the qualifications indicated:

Condux International, Incorporated warrants to the original purchaser for use
that the goods or any component thereof manufactured by Condux
International will be free from defects in workmanship for a period of 1 year
from the date of purchase, provided such goods are installed, maintained,
and used in accordance with Condux’s written instructions.

Components not manufactured by Condux International but used within the
assembly provided by Condux International are subject to the warranty period
as specified by the individual manufacturer of said component, provided such
goods are installed, maintained, and used in accordance with Condux’s and
the original manufacturer’s written instructions.

Condux’s sole liability and the purchaser’s sole remedy for a failure of goods
under this limited warranty, and for any and all claims arising out of the
purchase and use of the goods, shall be limited to the repair or replacement
of the goods that do not conform to this warranty.

To obtain repair or replacement service under the limited warranty, the pur­chaser must contact the factory for a Return Material Authorization (RMA).
Once obtained, send the RMA along with the defective part or goods,
transportation prepaid, to: Condux International, Inc.
145 Kingswood Drive
Mankato, MN 56001

Fiber Optic Cable Puller
Hitch Mount

THERE ARE NO EXPRESS WARRANTIES COVERING THESE GOODS
OTHER THAN AS SET FORTH ABOVE. THE IMPLIED WARRANTIES OR
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
LIMITED IN DURATION TO ONE YEAR FROM DATE OF PURCHASE.

CONDUX ASSUMES NO LIABILITY IN CONNECTION
WITH THE INSTALLATION OR USE OF THIS
PRODUCT, EXCEPT AS STATED IN THIS LIMITED
WARRANTY. CONDUX WILL IN NO EVENT BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES.

®

CONDUX

Condux International, Inc. • P.O. Box 247 • 145 Kingswood Drive • Mankato, MN 56001

1-507-387-6576 • 1-800-533-2077 • FAX [phone]
http://www.condux.com • e-mail: [e-mail]

© Copyright 2012, Condux International, Inc.

Literature Part Number: 08675909

Printed in USA

Revision Number: 1.1

Installation Procedure

1. Stabilize truck.

2. Remove pin to separate the jack from puller hitch mount
weldment.

3. Install puller hitch mount weldment to the truck’s hitch (take note,
jack receiver must be on the same side as the capstan).

4. Install and pin jack perpendicular to the puller hitch mount
weldment.

5. Stabilize the jack by cranking on the handle.

NOTE: Do not attempt to jack up the vehicle. This tool is not

intended to be used as a vehicle jack.

NOTE: Must not exceed 800 lbs (3,559 N) of pulling load.

6. Assemble fiber puller frame mount into female mounting tube.

7. Install snap lock pin to secure puller frame mount.

8. Install 30 inch capstan like instructed in its manual.

Removal Procedure

Puller Hitch
Mount Weldment

21⁄2" (64 mm)
Female Mounting
Tube

Pins

2" (51 mm) square
Reese type end

Pin Hole

Handle

Adjustable Jack

1. Removal is the opposite of the installation procedure.

!WARNING: Read and understand all procedure and
safety instructions before using the Condux Fiber
Optic Cable Puller Hitch Mount. Failure to do so
may result in personal injury or property damage.
Save this user’s guide for future reference.

ADVERTENCIA

Instrucciones
de Operación

!ADVERTENCIA: Favor de leer y comprender todas
las instrucciones de operación y seguridad antes
de usar el Condux Fiber Optic Cable Puller Hitch
Mount. Si Ud. no comprende las instrucciones
favor de consultarle a su jefe.

Figure 1. Fiber Optic Cable Puller Hitch Mount

!CAUTION: Wear personal protective equipment:
hard hat, safety glasses, safety shoes, and leather
work gloves. Failure to do this could result in
personal injury.