Page 1
INSTALLATION AND OPERATING INSTRUCTIONS
Adiabatic Atomiser Humidifier
2546634 EN 1112
Condair ABS3
Page 2
2
Page 3
3
Contents
1 Introduction 4
1.1 To the very beginning 4
1.2 Notes on the installation and operating instructions 4
2 For your safety 6
3 Product overview 8
3.1 Unit construction 8
3.2 Principle of operation 8
3.3 Identicationoftheunit 9
3.4 Accessories and options 9
3.5 Standard delivery 10
3.6 Storing/Transportation/Packaging 10
4 Mounting and installation work 11
4.1 Important notes for mounting and installation work 11
4.2 Mounting the unit 12
4.2.1 Notes on unit location 12
4.2.2 Wall mounting 13
4.2.3 Ceiling mounting (hanging installation) 14
4.3 Water installation 15
4.3.1 Overview water installation 15
4.3.2 Notes on water installation 16
4.4 Electric installation 17
4.4.1 Wiring diagram Condair ABS3 17
4.4.2 Notes on electric installation 18
4.4.3 Dismounting and mounting the electric
connection box 19
4.4.4 Notes regarding the cabling 20
4.4.5 Conguration 21
4.4.5.1Settingtheushingcycles 21
4.4.5.2Settingthehumidicationcapacitylimitation 21
5 Operation 22
5.1 Setting the unit into operation 22
5.2 Inspections during operation 22
5.3 Taking the unit out of operation 23
6 Maintenance 24
6.1 Important notes on maintenance 24
6.2 Maintenance intervals 24
6.3 Maintenance work 25
7 Troubleshooting 26
7.1 Important notes on troubleshooting 26
7.2 Malfunction list 26
8 Taking out of service/Disposal 27
8.1 Taking out of service 27
8.2 Disposal/Recycling 27
9 Productspecications 28
9.1 Technical data 28
9.2 Dimensions 28
9.3 Declaration of conformity 29
Page 4
4
Limitation
The subject of these installation and operating instructions is the adiabatic atomiser humidier
Condair ABS3. The various accessories are only described insofar as this is necessary for proper
operation of the equipment. Further information on accessories can be obtained in the respective
instructions.
These installation and operating instructions are restricted to the installation, commissioning,
operation, servicing, and trouble-shooting of the Condair ABS3 and is meant for well trained
personnel being sufciently qualied for their respective work.
The installation and operating instructions are supplemented by various separate items of documentation. Where necessary, appropriate cross-references are made to these publications in the
installation and operating instructions.
1 Introduction
We thank you for having purchased the adiabatic atomiser humidier Condair ABS3.
The Condair ABS3 incorporates the latest technical ad van ces and meets all recognized safety
standards. Nevertheless, improper use of the adiabatic air humidier Condair ABS3 may result in
danger to the user or third parties and/or impairment of material assets.
To ensure a safe, proper, and economical operation of the Condair ABS3, please observe and comply
with all information and safety instructions contained in the present installation and operating instruc-
tions as well as in the separate documentations of the components installed in the humidication
system.
If you have questions, which are not or insufciently answered in this documentation, please contact
your Condair supplier. They will be glad to assist you.
1.2 Notes on the installation and operating instructions
1.1 To the very beginning
Page 5
5
Symbols used in this manual
CAUTION!
The catchword “CAUTION” designates notes in this installation and operating instructions that, if
neglected, may cause damage and/or malfunction of the unit or other material assets.
WARNING!
The catchword “WARNING” used in conjunction with the general caution symbol designates safety
and danger notes in this installation and operating instructions that, if neglected, may cause to
injury to persons.
DANGER!
The catchword “DANGER” used in conjunction with the general caution symbol designates safety
and danger notes in this installation and operating instructions that, if neglected, may lead to severe
injury or even death of persons.
Safekeeping
Please safeguard these installation and operating instructions in a safe place, where they can be
immediately accessed. If the equipment changes hands, the documentation must be passed on to
the new operator.
If the documentation gets mislaid, please contact your Condair supplier.
Language versions
These installation and operating instructions are available in various languages. Please contact your
Condair supplier for information.
Copyright protection
The present installation and operating instructions is protected under the Copyright Act. Passing-on
and reproduction of the manual (or part thereof) as well as exploitation and communication of the
contents are prohibited without written permission by the manufacturer. Violation of copyright terms
is subject to legal prosecution and arises liability for indemnication.
The manufacturer reserves the right to fully exploit commercial patent rights.
Page 6
6
2 For your safety
General
Every person working with the Condair ABS3 must have read and understood the installation and
operating instructions before carrying out any work.
Knowing and understanding the contents of the installation and operating instructions is a basic
requirement for protecting the personnel against any kind of danger, to prevent faulty operation, and
to operate the unit safely and correctly.
All ideograms, signs and markings applied to the unit must be observed and kept in readable
state.
Qualication of personnel
All work (installation, operating, servicing , etc.) described in these installation and operating instructions may only be carried out by specialist who are well trained and adequately qualied and
are authorized by the customer.
For safety and warranty reasons any action beyond the scope of this manual must be carried out
only by qualied personnel authorised by the manufacturer.
It is assumed that all persons working with the Condair ABS3 are familiar and comply with the appropriate regulations on work safety and the prevention of accidents.
Intended use
The adiabatic atomiser humidier Condair ABS3 are intended exclusively for air humidication
within the specied operating conditions (see chapter 9 “Product specications”. Any other type
of application, without the written consent of your Condair supplier, is considered as not conforming
with the intended purpose and may lead to the Condair ABS3 becoming dangerous.
Operation of the equipment in the intended manner requires that all the information in these in-
structions are observed (in particular the safety instructions).
Page 7
7
Danger that may arise from the unit
DANGER! Danger of electric hazzard
One may get in touch with live parts when the wiring box is open. Touching live parts may
cause severe injury or danger to life.
Prevention: before carrying out any work set the Condair ABS3 out of operation as described in
chapter 5.4 (switch off the unit, disconnect it from the mains and stop the water supply) and secure
the unit against inadvertent power-up.
WARNING!
Badly maintained humidiers can endanger the health. If the unit is insufcient maintained
ill-making germs may grow in the water reservoir of the Condair ABS3 and may can affect the air
passing through the humidier.
Prevention: the Condair ABS3 must be cleaned in the prescribed intervals according to the infor-
mation given in chapter 6 “Maintenance". The cleaning works must be carried out correctly and
the air lter must be replaced after their prescribed lifetime has elapsed.
Behaviour in case of danger
If it is suspected that safe operation is no longer possible, then the Condair ABS3 should immediately be shut down and secured against accidental power-up according to chapter 5.4. This
can be the case under the following circumstances:
– if the Condair ABS3 is damaged
– if the Condair ABS3 is no longer operating correctly
– if connections and/or piping are not sealed
– if electrical cables are defective
– if the Condair ABS3 is no longer fastened correctly.
All persons working with the Condair ABS3 must report any alterations to the unit that may affect
safety to the owner without delay.
Prohibited modications to the unit
No modications must be undertaken on the Condair ABS3 without the express written consent
of the manufacturer.
For the replacement of defective components use exclusively original accessories and spare parts
available from your Condair supplier.
Page 8
8
3 Product overview
3.1 Unit construction
1 Air lter (EU3/C3)
2 Electrical connection box
3 Water reservoir
4 Cone with fan
5 Atomiser disk
6 Motor
7 Discharge hood, rotatable
3.2 Principle of operation
The Condair ABS3 operates according to the atom i zation principle.
The water is drawn in through cone (4) from the water reservoir (3) and is hurled from the atomiser
disk (5) against the atomiser collar (8), thereby producing aerosols (fog). The level in the water res-
ervoir is monitored and controlled with the oat switch (10).
The fan attached to the cone draws in room air through the air lter (1) on the bottom of the base
unit. This air transports the aerosols to the atomiser outlet (7) and distributes them in the room.
The humidier is controlled via an external On/Off humidistat or an external 0-10V continuous humidity controller which opens and closes the inlet valve. When controlled via the external continuous
humidity controller the inlet valve is opened and closed cyclically, depending on the control signal.
8 Atomiser collar
9 Water supply
10 Level switch
11 Water drain
12 Siphon
13 Unit housing
7
6
5
4
1
2
3
10
13
11
12
9
8
Page 9
9
Condair AG
8808 Pfäffikon
Condair ABS3 120 230V
F3003
Januar 09
Zerstäuber
Atomizer
Atomiseur
08/S01776/00001
2543376
Serial Nr.
230 V ~, 50/60 Hz, 230 W (300 W)
The indication of the unit as well as the most important unit data are found on the type plate:
Type designation
Outlet angle in degrees
Unit voltage
Unit voltage/power consumption
3.3 Identication of the unit
Serial number
Month/Year
3.4 Accessories and options
Accessories
Designation Code Description
Filter valve Z261 Filter valve with G 1/2" internal thread connectors for
the installation in the water supply line.
Room humidistat HSC On/Off room humidistat
Room humidistat H5 / H5V On/Off room humidistat (Note: this humidistat can be
used as a maximum humidistat).
Room humidity controller RCC 0-10 V continuous humidity controller with sensor
Options
Designation Code Description
Anti-freeze kit AFP Anti-freeze kit for the operation of the Condair ABS3
up to a temperature of -2 °C. The anti-freeze kit
consist of a heating element connected to the control board. The Condair ABS3 is prepared for the
installation of the anti-freeze kit. The control of the
heating element is established via the temperature
sensor built into the unit. The temperature sensor
switches the heating element on if the ambient temperature drops below 1°C.
Approval symbols
Page 10
10
3.5 Standard delivery
The standard delivery includes:
– Adiabatic atomiser humidier ABS3 with options according delivery note.
– Ordered accessories with operating instructions, packed separately
– Installation and operating instructions (this document).
– Fixing set for the wall mounting of the unit (1 pc. wall bracket, 4 screws with dowels ø8 mm, 1 pc.
safety screw M6x20 with washer ø6x12)
– Fixing set for the hanging installation (3 pcs. angle brackets)
– Water supply pipe (L: 1.5 m, with G 3/4" union nuts)
– Adapter G 1/2" - G 3/4"
– Water drain pipe (L: 1.5 m, internal diameter: 10 mm)
– 2 pcs. cable straps
– Spare parts list
3.6 Storing/Transportation/Packaging
Storing
Store the unit in the original packaging in a protected area meeting the following requirements:
– Room temperature: 1 ... 40 °C
– Room humidity: 10 ... 75 %rh
Transportation
For optimum protection always transport the unit in the original packaging.
If possible, always transport the unit with the help of another person.
Packaging
Keep the original packaging of the Condair ABS3 for later use.
In case you wish to dispose of the packaging, observe the local regulations on waste disposal. Never
dispose of the packaging to the environment.
Page 11
11
4 Mounting and installation work
4.1 Important notes for mounting and installation work
Qualication of personnel
All mounting and installation work must be carried out only by well qualied personnel, which is
familiar with the Condair ABS3.
All work concerning the electric installation must be performed only by adequately qualied personnel
(electrician or workman with equivalent training).
Safety
The Condair ABS3 may be connected to electric mains only after all installation work has been
completed.
The local regulations relating job safety must be followed and complied with for all installation and
mounting work.
General notes
All statements relating to the positioning and installation of the ABS3 as well as to the water and
electrical installation must be followed and complied with.
Observe and comply with all local regulations dealing with water and electrical installations.
When installing individual components use the xing materials supplied with the unit. If xing
with the materials supplied is not possible in your particular case, select a method of xing that is of
similar stability. In case of doubt, please contact your Condair supplier.
The connection of the water supply pipe and the water drain pipe on the unit (see chapter 4.3) as
well as the connection of the main cable and the cable of the external humidistat/humidity controller
in the unit (see chapter 4.4) can be done before the unit is mounted to the wall/ceiling.
Page 12
12
4.2 Mounting the unit
4.2.1 Notes on unit location
In order to ensure the correct function of the humidier and the accessibility for maintenance, please
observe the following locating instructions:
– The Condair ABS3 humidiers are designed for wall mouting or ceiling mounting (hanging instal-
lation). Make sure that the structure (wall, pillar, ceiling, etc.) on which the unit is to be mounted
has sufcient carrying capacity and can accommodate the fastening elements.
– In order to ensure the correct function, the Condair ABS3 must be installed exactly horizontal
(with the air lter facing downward against the oor).
– Locate the unit such that the aerosol stream can spread freely. The obstruction of the aerosol
stream by objects such as tubular racks, machines, supports, etc., will result in stagnation and
the formation of turbulence which could cause condensation. Since the discharge hood of the
humidier can be turned horizontally, the aerosol stream can be directed to bypass any obstructions.
In the following table you nd the minimum distances (appoximate values), which must be
maintained when positioning the Condair ABS3. The dimensions relate to a room temperature of
20 °C and a relative humidity of 45 %. At lower temperatures and/or higher relative humidity larger
minimum distances must be maintained
Wall mounting Ceiling mounting
E
C
D
D
B
E
A
A
B
C
A B C D E
Minimum distance in m ≥ 3.0 ≥ 1.0 ≥ 1.5 ≥ 1.0 ≥ 5.0
– Mount the unit such that there is sufcient room for maintenance. Also make sure that the unit
is readily accessible and that there is no accident risk during maintenance.
– If units are to be installed facing each other, make sure that they are at least 10 m apart.
– Insulate cold water piping in the vicinity of the aerosol stream (risk of condensation).
– The evaporation process extracts heat from the ambient air. Make sure, therefore, that the aerosol
stream is not directed at persons.
Page 13
13
4.2.2 Wall mounting
To x the humidier to the wall, use the wall bracket, screws and dowels provided. The wall bracket
can be used as template for the xing holes.
Mounting the wall bracket
1. Mark the xing holes on the wall using the wall bracket as template. Make sure the wall bracket
is aligned exactly horizontal before marking the holes.
2. Drill the four xing holes (ø8 mm, 45mm deep).
3. Clean the holes and insert the dowels.
4. Fix the wall bracket with four screws to the wall (position of the bracket as shown in the gure
above). Before tightening the screws align the wall bracket exactly horizontal.
Mounting the unit
1. Lift the unit above the wall bracket and swivel it slightly towards the wall.
2. Move the unit towards the wall into the wall bracket.
3. Swivel the unit to the horizontal position until both brackets are perfectly coupled.
4. Secure the unit in the wall bracket with the safety screw M6x20 and the washer ø6x12 supplied
(mandatory).
2.
1.
3.
4.
4.
Page 14
14
4.2.3 Ceiling mounting (hanging installation)
Ceiling mounting is done with the angle brackets supplied as standard.
The three chains for hanging up the unit must be provided by the customer.
The chains must be xed at the ceiling exactly perpendicularly above the
three angle brackets xed to the unit. The xing points and the chains must
have a sufcient load-bearing capacity, in order to carry the weight of the
unit (see chapter 9.1 “Technical data”).
Use chains made of steel (preferably corrosion-resistant steel). The dimension
of the chain links must meet to the specications in the adjacent gure.
1. Undo the 4 screws “V”, and remove the
mounting plate “A” on the backside of the
unit.
Note: Store the mounting plate “A” for a
possible later use.
Now, you have 5 screws with washers (4
from the just removed mounting plate and
the safety screw provided). Ret two of the
screws and washers into the xing holes
“F”.
2. Fix the three angle brackets (for hanging
installation) with the screws and washers to
the unit, as shown in the adjacent gure.
3. Hook the unit with the angle brackets into the chains and check again that the device hangs
exactly horizontal.
Page 15
15
4.3 Water installation
4.3.1 Overview water installation
A Water supply pipe (included in the delivery, L: 1.5 m, G 3/4")
B Stop valve (by client)
C Water lter (accessory Z261, installation recommended, by client)
D Drain pipe (included in the delivery, L: 1.5 m) with constant downward slope >10°
E Open drain funnel with siphon (by client)
Connector water supply G 3/4"
Water supply pipe
Connector
water drain ø10 mm
Drain pipe
ø12/10 mm
Page 16
16
4.3.2 Notes on water installation
Water supply
The water supply is to be carried out according to the gure found in chapter 4.3.1 and the applicable
local regulations for water installations. The indicated connection specications must be observed.
– The installation of a stop valve (mandatory) and a water lter (accessory “Z261”, installation
recommended) should be made as close as possible to the unit.
– Notes on water quality:
– For the water supply of the Condair ABS3, use exclusively untreated drinking water or fully
demineralised water.
– The use of additives such as corrosion inhibitors, disinfectants, etc. is not allowed, since
these additives may endanger health and affect proper operation.
– The connection material must be pressure-proof and certied for use in drinking water systems.
– Important! Before connecting the water line, the line should be well ushed out.
CAUTION!
The thread at the humidier connection is made of plastic. To avoid overtightening, the union
nut of the water pipe must be tightened by hand only..
Water drain
The water drain is to be carried out according to the gure found in chapter 4.3.1 and the applicable
local regulations for water installations. The indicated connection specications must be observed.
– Make sure that the drain line is routed with a constant downward slope >10° to the drain funnel
of the building.
Important: The drain pipe must be prevented from sagging; support with brackets, if necessary.
– Make sure that the minimum inside diameter of 10 mm is maintained throughout the entire length
of the drain pipe and that the pipe is not kinked.
– Make sure that the drain pipe is correctly xed and easily accessible for inspections and cleaning
purposes.
When operating the Condair ABS3 with fully demineralised water:
Fully demineralised water is aggressive! For this reason, use exclusively installation material
made of corrosion-resistant steel (min. DIN 1.4301) or plastic.
Page 17
17
4.4 Electric installation
4.4.1 Wiring diagram Condair ABS3
A1 Continuous humidity controller 0...10 V
A2 On/Off humidistat
A3 Maximum humidistat (not mandatory, required contact load: 230V/2A or 115V/4A)
S1 Temperature sensor (to switch the optional heating H1 on and off)
S2 Level switch
H1 Heating (option anti-freeze kit)
F1 Internal fuse transformer (315 mA, slow acting)
F2 External fuse voltage supply (2.5 A, slow acting)
M Fan motor
Q2 External service switch (with a minimum contact clearance of 3 mm)
SW1 DIP switches for setting the ushing cycles
SW2 Rotary switch for setting the power limit
Y1 Inlet valve
K1
SW1
SW2
Off On
50
0 100
N L1 K2 K3
24V LEVELGND IN
24VIN
NTC
M
MIN
1.1 l/h
MAX
6.5 l/h
1
2
Q2
F2
F1
115 V / 50/60Hz
230 V / 50/60Hz
S1
S2
Y1
H1
A2
A1
– +
P / PI
ON-OFF
A3
ON-OFF
24 VDC / 60 mA
internal
external
Page 18
18
4.4.2 Notes on electric installation
The electric installation must be carried out according to the wiring diagram in chapter 4.4.1 and
the applicable local regulations. All information given in the wiring diagram must be followed and
observed.
The electrical installation of the Condair ABS3 includes:
Installation
Power supply 230V/50-60Hz or 115V/50-60Hz
Connection of power supply to terminals L1 and N according to the wiring diagram. The service
switch Q2 (disconnects all 2 wires with a minimum contact clearance of 3 mm) and the fuses F2
(2.5 A, slow acting) are mandatory.
Cable section according to the applicable local regulations.
CAUTION!
Before connecting the power supply cable make sure the local mains voltage meet the value
stated on the rating plate of the Condair ABS3.
External humidity controller (A1) or external On/Off humidistat (A2)
Connect the external humidity controller 0...10V to terminals IN (+) and GND (–) or connect the
external On/Off humidistat to terminals IN and 24V.
Note: In locations with electromagnetic interferences use shielded connecting cables.
Maximum humidistat (A3), not mandatory
Connect the switching contact of the maximum humidistat to supply line L1 according to the wiring
diagram.
Required contact load: 230V/2A or 115V/4A
Note: In order to connect the mains cable and the cable of the external humidistat/humidity controller to the control board, the electric connection box in the unit must be dismounted and opened.
For this purpose please observe the notes in chapter 4.4.3 and the notes regarding the cabling in
chapter 4.4.4.
Page 19
19
2. Push xing clip “C” sidewards and carefully pull connection box out of the unit.
3. Undo the four screws of the connection box and remove the cover.
Now you can connect the cables on the control board or congure the control.
CAUTION!
The electronic components inside the electric connection box are very sensitive to electro-
static discharge. When the unit is open for installation work, appropriate measures must be
taken to protect these components against damage caused by electrostatic discharge
(ESD protection).
Mounting the electric connection box
1. Re-attach the cover of the connection box and x it with the four screws.
4.4.3 Dismounting and mounting the electric connection box
Dismounting the electric connection box
1. Undo the three screws at the air lter assembly and remove the air lter assembly.
2. Replace the connection box into the receptacle in the unit and x it with the xing clip.
3. Set the air lter assembly (grid-lter-grid) into the bottom of the unit an x it with the three
screws.
C
Page 20
20
4.4.4 Notes regarding the cabling
Pass the power supply cable through the cable gland “1a” into the unit and through the cable gland
“1b” into the electric connection box and connect it to the control board according to the wiring diagram.
Pass the cable of the external controller/humidistat through the cable gland “2a” into the unit and
through the cable gland “2b” into the electric connection box and connect it to the control board according to the wiring diagram.
Fix both cables with the cable straps provided to the existing cables at the places marked with arrows. Finally, tighten the four cable glands.
K1
SW1
SW2
Off On
50
0 100
N L1 K2 K3
24V LEVELGND IN
24VIN
NTC
MIN
1.1 l/h
MAX
6.5 l/h
1
2
Q2
F2
F1
115 V / 50/60Hz
230 V / 50/60Hz
A2
A1
– +
P / PI
ON-OFF
1b
2b
2b
A1 / A2
max. 46 mm
1b
115 V / 50/60Hz
230 V / 50/60Hz
max. 53 mm
1a
1b 2b
2a
dismantling
dismantling
Page 21
21
4.4.5 Conguration
For the conguration the electric connection box in the unit must be dismounted and opened. For
this purpose please observe the notes in chapter 4.4.3.
4.4.5.1 Setting the ushing cycles
The ushing cycles are set via the DIP switches SW1 on the control board:
SW1
Off On
1
2
SW1 On Off
1 During operation a ushing cycle
is performed every 6 hours.
The 6 hours ushing cycle during
operation is deactivated (e.g. for
the operation with fully demineralised water).
2 After 72 hours without humidity
demand a ushing cycle is performed before the next humidi-
cation cycle.
72 hours ushing deactivated.
4.4.5.2 Setting the humidication capacity limitation
SW2
50
0 100
MIN
1.1 l/h
MAX
6.5 l/h
The humidication capacity limitation is set via the rotary switch SW2 on the
control board.
Setting range: 0 (1.1 l/h) ... 100 (6.5 l/h)
Factory setting: 100 (6.5 l/h).
Page 22
22
5 Operation
Proceed as follows when putting the Condair ABS3 into operation:
1. Check the Condair ABS3 and the installations for possible damage.
DANGER!
A damaged unit or an unit with damaged installation may present danger to human life or cause
severe damage to material assets.
A damaged unit and/or an unit with damaged or faulty installation must not be operated.
2. Make sure that the electric connection box is closed, correctly set in the receptacle of the unit
and secured and that the air lter assembly is correctly mounted and fastened.
3. Open the stop valve of the water supply line and check water system for leakages.
CAUTION!
An unit with leakages must not be operated.
4. If necessary, turn outlet openings of the diffusor into the desired blow-out direction.
5. Verify the set humidity value at the external humidity controller/humidistat, and readjust as required.
6. Turn on the service switch in the mains supply line.
The unit performs a ushing cycle, which takes approx. 1 minute. Then, the unit is ready for operation. As soon as the external humidity controller or the humidistat requires humidity the motor
starts and the atomisation begins.
5.1 Setting the unit into operation
5.2 Inspections during operation
During operation the Condair ABS3 and the humidication system have to be inspected weekly. On
this occasion check the following:
• the water installation for any leakage.
• the humidier and the other system components for correct xing and any damage.
• the electric installation for any damage.
If the inspection reveals any irregularities (e.g. leakage, irregular running) or any damaged components take the Condair ABS3 out of operation as described in chapter 5.3. Then, let the damage or
malfunction be resolved by a qualied specialist or a service technician of your Condair supplier.
Note: During operation individual drops are carried along by the air ow and thrown against the hood.
This causes an audible noise, which is completely normal.
Page 23
23
5.3 Taking the unit out of operation
Proceed a follows to put the Condair ABS3 out of operation (e.g. for maintenance work, elimination
of a malfunction):
1. If the Condair ABS3 humidies right now: Set the humidity reference value on the external humid-
ity controller/humidistat to 0 %rh and wait until the unit has nished the ushing cycle (approx. 1
minute).
2. Turn off the service switch in the mains supply line, then secure the service switch against inadvertent switching on.
3. Close the stop valve of the water supply line.
Note: If the Condair ABS3 is not used for prolonged period of time, cover the unit with a plastic
hood.
Page 24
24
6 Maintenance
Qualication of personnel
All maintenance work must be carried out only by well qualied and trained personnel authorised
by the owner. It is the owner’s responsibility to verify proper qualication of the personnel.
General note
The instructions and details for maintenance work must be followed and upheld.
Only the maintenance work described in this documentation may be carried out.
Only use original Condair spare parts to replace faulty parts.
Safety
DANGER!
Before maintenance is initiated, the Condair ABS3 must be tak en out of operation in accord-
ance with instructions in chapter 5.3 and protected against unintentional switching on.
WARNING!
If the Condair ABS3 is insufciently maintained ill-making germs can increase in the water reservoir
by the time and get into the ambient air.
6.1 Important notes on maintenance
6.2 Maintenance intervals
In order to maintain operational safety the Condair ABS3 must be maintained in regular intervals. The
time interval for the maintenance is to be adapted to the operating conditions. The hygiene
status depends mainly on the quality of the humidier water and the micro-biological and chemical
composition of the supply air. Therefore the maintenance intervals must be determined for each
system separately.
The rst visual check must be carried out after 200 operating hours. Depending on the en-
countered hygiene status during this rst check the maintenance interval time must be decreased
or increased.
In any case the Condair ABS3 is to be maintained however at least twice annually.
Page 25
25
6.3 Maintenance work
Component Work to be carried out
Air lter
1. Undo the three screws and remove the air lter assembly
downwards.
2. Clean lter mat on both sides with a vacuum cleaner.
3. Place the cleaned lter mat between the two lter grids, then
insert the lter assembly from downside into the unit and x
it with the three screws.
Note: If the lter mat is heavily contaminated, replace the lter
mat (EU3/C3).
Drain siphon
1. Undo the three screws and remove the air lter assembly
downwards.
2. Remove pipe “B” from the connector.
3. Undo the two screws “C”, then remove the connection piece
“A” from the siphon.
4. Clean siphon and connection piece.
5. Assemble the unit in reverse order of steps 1… 4.
Sieve in the inlet valve
1. Remove supply pipe “A”.
2. Pull the sieve out of the inlet valve.
3. Clean the sieve.
3. Insert the sieve into the inlet valve.
5. Re-connect supply pipe “A” and tighten union nut by hand.
Note: If the sieve must be cleaned often, a water lter should be
installed in the water supply line (see chapter 4.3.1).
Page 26
26
7 Troubleshooting
7.1 Important notes on troubleshooting
Qualication of personnel
Have faults eliminated by adequately qualied and trained personnel only. Malfunctions caused by
the electrical installation must be repaired by authorized personnel (e.g. electrician) only.
Repair work and the replacement of defective parts may only be carried out by your Condair representative’s service technician.
Safety
In order to eliminate faults, the Condair ABS3 must be set out of operation as described in chapter
5.3, disconnect the unit from the mains and secure the unit against inadvertent power-up.
Important! Most operational malfunctions are not caused by faulty equipment but rather by improper
installation. Therefore, a complete fault diagnosis always involves a thorough examination of the
entire system.
Malfunction Cause Remedy
The atomiser does not run, although the service switch in the
mains supply line is switched
on.
The current humidity in the room
is higher than the set reference
humidity value.
None, wait.
Fuse F2 in the mains supply line
defective.
Check/replace fuse F2.
The atomiser keeps running
and cannot be switched off by
reducing the reference humid-
ity value.
Air humidity very low (<45 %rh) None, wait.
External humidity controller/
humidistat defective.
Check/replace external humidity
controller/ humidistat
The set reference humidity value
is not reached. The atomiser runs
continuously.
Air lters heavily contaminated. Clean air lter.
Room too large. Contact Condair dealer.
Suction tube of atomiser unit
blocked.
Check suction cone. Clean if necessary.
The atomiser runs noisily. Atomiser assembly not correctly
installed.
Check atomiser assembly. Mount
parts correctly.
Suction cone has become undone. Tighten the suction cone.
7.2 Malfunction list
Page 27
27
8 Taking out of service/Disposal
8.1 Taking out of service
If the Condair ABS3 must be replaced or if the humidication system is not needed any more, proceed as follows:
1. Take the unit out of operation as described in chapter 5.3.
2. Have the unit (and all other system components, if necessary) unmounted by a qualied service
technician.
8.2 Disposal/Recycling
In conformance with the European Directive 2002/96 EC on Waste Electrical and Electronic Equipment (WEEE) this device may not be disposed of in domestic waste.
This also applies to countries outside the EU, per their specic requirements.
Please dispose of this product in accordance with local regulations at the collecting
point specied for electrical and electronic equipment.
If you have any questions, please contact the responsible authority or the distributor
from which you purchased this device.
Should this unit be passed on to other parties (for private or professional use), the
content of this regulation must also be related.
Thank you for your contribution to environmental protection.
Page 28
28
9 Product specications
9.1 Technical data
Humidication capacity 1.1 ... 6.5 l/h
Unit voltage 230V / 50/60Hz or
115V / 50/60Hz
Power consumption 0.23 kW
(0.3 kW with optional anti-freeze kit)
Air circulation 280 m
3
/h (77.8 l/s)
Content water reservoir 0.055 l
Unit weight 17.6 kg
Connector water supply R 3/4" outside thread
Connector water drain ø 10 mm
Admissible pressure water supply 1...10 bar (0.1...1.0 MPa)
Admissible temperature water supply 5...45 °C
Water quality Tap water or
fully demineralised water
Admissible operation temperature/humidity +2 ... +35 °C / 0 ... <100 %rh **
Admissible operation temperature/humidity
(with optional anti-freeze kit)
–2 ... +35 °C / 0 ... <100 %rh **
Admissible storage temperature/humidity –10 ... +60 °C / 0 ... 80 %rh
Type of protection IPX4
Conformity CE mark
** non-condensing
9.2 Dimensions
120° version
A B C D
Dimensions in mm 565 505 530 610
360° version
A B C
Dimensions in mm 565 505 530
D
C B
B C
Page 29
29
9.3 Declaration of conformity
Condair Ltd
Member of the Walter Meier Group
Talstrasse 35–37
8808 Pfäffikon, Switzerland
Tel. +41 55 416 61 11, Fax +41 55 416 62 62
info@condair.com, www.condair.com
EC
Konformitätserklärung
Declaration of conformity
Déclaration de conformité
Wir,
Condair AG
CH-8808 Pfäffikon SZ
erklären in alleiniger Verantwortung,
dass das Produkt
We,
Condair Ltd.
CH-8808 Pfäffikon SZ
declare under our sole responsibility, that
the product
Nous,
Condair SA
CH-8808 Pfäffikon SZ
déclarons sous notre seule
responsabilité, que le produit
Condair ABS3
auf das sich diese Erklärung bezieht,
mit den folgenden Normen oder
normativen Dokumenten
übereinstimmt
to which this declaration relates is in
conformity with the following standards or
other normative standards
auquel se réfère cette déclaration est
conforme aux normes ou autres
documents normatifs
EN 61000-6-2
EN 61000-6-3
EN 60335-1
EN 60335-2-98
und den Bestimmungen der folgenden
Richtlinien entspricht
and is corresponding to the following
provisions of directives
et est conforme aux dispositions des
directives suivantes
2006 / 95 / EC
2004 / 108 / EC
Pfäffikon
, January 01, 2012
Condair Ltd
Thomas Grütter
Head of Development
2546297 DE/EN/FR 1201
Page 30
Notes
Page 31
© Condair Ltd., Printed in Switzerland
Technical modifications reserved
Page 32
CONSULTING, SALES AND SERVICE:
Manufacturer:
Condair Ltd.
Member of the Walter Meier Group
Talstrasse 35-37, 8808 Pfäffikon, Switzerland
Ph. +41 55 416 61 11, Fax +41 55 416 62 62
info@condair.com, www.condair.com
Reg.No. 40002-2
Loading...