Concept Pro CBP4304, CVP9304, CBP4324 User Manual

CBP4304
CBP4324
CVP9304

Colour Dome Camera

USER MANUAL

1. This installation should be made by a qualified service person and should abide to all local

codes.

2. Avoid installation on a surface subjected to frequent vibration or shocks.

3. Do not operate the camera beyond its temperature range or power source ratings.

4. Should any damage or suspected damage occur, shutdown the power source, unplug and

contact your service provider.

5. Do not install the camera under unstable lighting conditions. Severe lighting change or

flicker can cause the camera to work improperly.

6. Never use the camera close to a gas or oil leak.

7. Do not disassemble the camera.

8. Never keep the camera face to strong light directly, this can damage the CCD.

9. Ensure all removable covers are replaced to protect the inner components.

10. Do not install near devices which emit a strong electro-magnetic field.

11. Use a dry or damp cloth only for cleaning.

12. Internal dome only - Do not drop the camera or subject the unit to physical shocks.

PLEASE FOLLOW THE ABOVE CAUTIONS – FAILURE TO DO SO MAY

INVALIDATE THE WARRANTY OR CAUSE SERIOUS INJURY.

Remark: Changes or modifications not expressly approved by the manufacturer can
cause the camera to be damaged and become inoperable. This may invalidate the
user warranty.

CAUTION

Important: Ensure all cautionary procedures are
observed during installation.

It is recommended the camera is tested during the most
demanding environmental conditions such as low light
or bright sunlight to ensure continuity of effective CCTV
monitoring.

 Using the supplied fitting screws, securely attach the

camera to the drilled surface

 Adjust the tri-axis gimbal zoom/focus to give the

required image of the area to be monitored.

 Replace the dome cover by pushing firmly in place

onto the base

 Carefully clean the dome surface with a soft lint

free cloth

 Remove the camera unit carefully from the box

reserving the accessory contents in a safe place

 Use the supplied mounting template to mark the

space for drilling

 Remove the dome cover using a suitable coin or

screwdriver

FIXING TO A WALL

CBP4304/4324

Ceiling

PACKING CONTENTS

CBP4304 / 4324

Wall Plugs

X4

Mounting Template

X1

Fitting Screws

X4

INTERNAL DOME INSTALLATION

Important: Ensure all cautionary procedures are
observed during installation.

It is recommended the camera is tested during the most
demanding environmental conditions such as low light
or bright sunlight to ensure continuity of effective CCTV
monitoring.

 Attach the weatherproof sealing pad to the base of

the dome with the sticky side against the camera

 Using the supplied fitting screws, securely attach the

camera to the drilled surface
Please note: To ensure correct weatherproof you
must use the enclosed fitting screws and
weatherproof washers

 Adjust the tri-axis gimbal zoom/focus to give the

required image of the area to be monitored.

 Replace the dome cover and tighten the dome cover

screws using the supplied dome cover screw driver

 Carefully clean the dome surface with a soft lint

free cloth

 Remove the camera unit carefully from the box

reserving the accessory contents in a safe place

 Use the supplied mounting template to mark the

space for drilling

 Remove the dome cover using the supplied dome

cover screwdriver

FIXING TO A WALL

CVP9304

PACKING CONTENTS

Wall Plugs

X4

Conduet hole cover
opener

X1

Mounting Template

X1

Fitting Screws

X4

Dome cover
screwdriver

X1

Weatherproof
sealing washers

X8

Weatherproof
sealing pad

X1

Ceiling

CVP9304

VANDAL RESISTANT DOME INSTALLATION

CONNECTION

 Connect the video out port to your video cable

running to the monitor / recorder

 Check the power supply is of the correct level

and connect your power supply into the power
port on the Camera.

 View the picture on a monitoring device to

check the power and video connection is
working properly.

PSU

Troubleshooting

 Ensure all power and cable connections are correct with the Camera and DVR.
 If all power and cable connections are correct and the camera picture can not be

produced then contact your supplier for technical support.

Tri-Axis Gimbal

Example shows vandal resistant dome casing

360º

90º

360º

94.64

51.0135.48

148.39

46.00

82.50

105.00

86.00

86.00

94.64

53.18

15.00

147.97

106.10

CVP9304CBP4304 / 4324

SPECIFICATION

Design and specification are subject to change without notice.

MODEL

Image Sensor

Effective Pixels

Horizontal Resolution

Min. Illumination

Lens

Day & Night

S/N Ratio

White Balance

AGC

BLC

Sync System

BNC Video Output

Input Voltage

Power Consumption

Operating Temperature

Dimension

Weight

CBP4304 CBP4324

Sony Super HAD

PAL: 500(H) x 582(V) ; NTSC: 510(H) x 494(V)

420TVL

0.3Lux/F1.2

Colour Only

more than 48dB

AUTO

AUTO

AUTO

Internal

CVBS 1.0Vp-p / 75Ω

12v DC

120mA

-10ºC~ +50ºC RH90% MAX

Fixed Lens f=4mm

Auto Iris Vari-focal

lens F=4-9mm

148x106 (DxH)

650g

SPECIFICATION

Design and specification are subject to change without notice.

MODEL

Image Sensor

Effective Pixels

Horizontal Resolution

Min. Illumination

Lens

Day & Night

S/N Ratio

White Balance

AGC

BLC

Sync System

BNC Video Output

Input Voltage

Power Consumption

Operating Temperature

Dimension

Weight

CVP9304

Sony Super HAD

PAL: 500(H) x 582(V) ; NTSC: 510(H) x 494(V)

420TVL

0.3Lux/F1.2

Fixed Lens f=4mm

Colour Only

more than 48dB

AUTO

AUTO

AUTO

Internal

CVBS 1.0Vp-p / 75Ω

12v DC

120mA

-10ºC~ +50ºC RH90% MAX

148.35x105 (DxH)

950g

CONCEPT PRO DOME CAMERA RANGE

INTERNAL DOME CAMERAS

CBP3212

CBP5112

CBP5212

CBP4304

CBP5314

CBP4324

CBP6324

CBP6324-B

CBP6324DN

CBP6324WDR

VANDAL RESISTANT DOME CAMERAS

CVP9304

CVP9314

CVP9324

CVP9324DN

CVP9324LL

CVP9324WDR

INFRARED DOME RANGE

CBP6314DNIR

CBP6324DNIR

CVP9314DNIR

CVP9324DNIR

VANDAL RESISTANT WALL BRACKET

CVP-BRK

480TVL, 0.3 Lux, 3.6mm Lens. 90(ø)x62mm

420TVL, 0.3 Lux, 3.6mm Lens, 128(ø)x93mm

480TVL, 0.3 Lux, 3.6mm Lens, 128(ø)x93mm

420TVL, 0.3 Lux, 4mm Lens, 148(ø)x106mm

650TVL, 0.03Lux, 4mm Lens, 148(ø)x106mm

420TVL, 0.3 Lux, 4-9mm Lens,148(ø)x106mm

650TVL, 0.03Lux 2.8-10mm Lens, 148(ø)x106mm

650TVL, 0.03 Lux, 2.8-10mm Lens, 148(ø)x106mm, Black casing

650TVL, 0.03 Lux, 2.8-10mm, Day Night, 148(ø)x106mm

690TVL, 0.01 Lux, 2.8-10mm Lens, Day Night, Wide Dynamic

Range,148(ø)x106mm

420TVL, 0.3 Lux, 4mm Lens, 148.35(ø)x105mm

650TVL, 0.03Lux, 4mm Lens, 148.35(ø)x105mm

650TVL, 0.03Lux 2.8-10mm Lens, 148.35(ø)x105mm

650TVL, 0.03 Lux, 2.8-10mm, Day Night, 148.35(ø)x105mm

600TVL, 0.0002 Lux (DSS/Sens Up on) 2.8-10mm Lens,

148.35(ø)x105mm

690TVL, 0.01 Lux, 2.8-10mm Lens, Day Night, Wide Dynamic Range,

148.35(ø)x105mm

600TVL, 4mm Lens, IR LED, 148(ø)x106mm

650TVL, 2.8-10mm Lens, IR LED, ICR, 148(ø)x106mm

600TVL, 4mm Lens, IR LED, 148.35(ø)x105mm

650TVL, 2.8-10mm Lens, IR LED, ICR, 148.35(ø)x105mm

Wall bracket for use with all CVP dome cameras