Conair XT10TC, XT10WTCSC Instructions For Use Manual

IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially when children are present, basic safety pre­cautions should always be taken, including the following:
READ ALL INSTRUCTIONS
BEFORE USING
DANGER–Any appliance is electrically
live, even when the switch is off.
To reduce the risk of death or injury by electric shock:
1. Always unplug appliance from electrical outlet immediately after using (except when charging unit).
2. Do not place or store appliance where it could fall or be pulled into a tub or sink.
3. Do not use appliance while bathing or in the shower.
4. Do not place appliance in, or drop into, water or other liquid.
5. If appliance has fallen into water, do not reach for it. Unplug immediately.
6. Unplug this appliance before cleaning.
DO NOT REACH
INTO THE WATER
WARNING–
To reduce the risk of burns, electric shock, fire, or injury to persons:
1. Never leave a plugged-in appliance unattended.
2. Close supervision is necessary when
Conair wants to thank you for choosing our beard/mustache
trimmer. We know it will
provide you with years of service.
Pivoting Head
Beard & Mustache
TRIMMER
®
Model XT10TC/XT10WTCSC
l’ajustement des lames. Si vous faites
réparer la tondeuse, assurez-vous que
les deux lames sont affûtées ou
remplacées en même temps. Pour
Pour obtenir de meilleurs résultats, les
poils devraient être légèrement humides
(PAS MOUILLÉS) quand vous utilisez la
tondeuse. Vous éviterez ainsi de couper
TAKING CARE OF
YOUR TRIMMER
OILING THE BLADES
About once a month you should oil the trimmer blades with the oil provided in your kit. It is best to do this over a piece of newspaper. Turn the trimmer on and hold it so that the blades are pointed downward. Spread one drop of oil across the blades, then turn the trimmer off and wipe away the excess oil with a soft cloth. Be careful not to use too much oil and don’t oil your trimmer more than neces­sary, as that could damage the motor. (Never attempt to oil the motor bearing as it is permanently lubricated.) After oiling the blades, return the trimmer and oil packet to the trimmer storage base.
BLADE CARE
Because the trimmer blades are precision­made for a very special use, they should always be handled with care. Each time you finish using the trimmer, take the cleaning brush provided and brush away any loose hair that has collected in the blades. Then store the trimmer in its recharging storage base to protect the blades until the next use. Be especially careful when changing or adjusting blades. When you have your trimmer serviced, be sure that both blades are sharpened or replaced at the same time. To promote the long life of the appliance, use your trimmer only for the purpose intended by the manufacturer—to trim your beard and mustache.
TURBO FEATURE
This product is equipped with a turbo boost button. When activated, this feature will provide 15% more cutting power. This is especially useful for cutting through thicker hair. To activate the turbo feature:
1. Turn the Power switch to the “on” position
2. Press the Turbo button
3. Continue to press the Turbo button for as long as you need the extra power
4. Release the Turbo button to return to normal power
GROWING A BEARD AND MUSTACHE
There are three key factors that will determine which beard or mustache style is best for you:
1. The shape and dimensions of your face.
2. The natural growth of your beard/mustache.
3. The thickness of your beard/mustache. If you are unsure of the type of beard or mustache that would most suit your face, speak with a professional hair stylist and ask for an opinion on what style would be best. Once your beard or mustache has been styled, it is essential that you maintain its appearance. To do this, use your trimmer to trim your beard/ mustache weekly. For the best trimming results, your beard should be slightly damp (NOT WET) when using your trimmer. This will prevent the trimmer from removing more hair than desired.
DIRECTIVES IMPORTANTES
1. Ne laissez jamais un appareil branché
sans surveillance.
peigne. Enfoncez-les en
GRADE 7 = 5/8"
this appliance is used by, on, or near children or individuals with certain disabilities.
3. Use appliance only for its intended use as described in this manual. Only use attachments recommended by the manufacturer. Do not use an extension cord to operate the appliance.
4. Never operate the appliance if it has a damaged cord or plug, is not working properly , has been dropped or damaged, or dropped into water. Return the appliance to a Conair service center for examination and repair.
5. Keep the appliance cord away from heated surfaces.
6. Do not pull, twist or wrap the cord around the appliance.
7. Never drop or insert any object into any opening of the appliance.
8. Do not place the appliance on any surface while it is operating.
9. Do not use the appliance with a damaged or broken comb or with teeth missing from the blades, as injury may result. Before each use, make certain the blades are aligned properly and oiled.
10. Do not use the appliance outdoors or where aerosol (spray) products are being used or oxygen is being administered.
11. THIS PRODUCT IS FOR HOUSEHOLD
USE ONLY.
SAVE THESE
INSTRUCTIONS
TROUBLESHOOTING
If your rechargeable trimmer does not seem to be taking a charge, take the following troubleshooting steps before
returning it for repair:
1. Be sure the electrical outlet is working by plugging in another appliance to test it.
2. Make sure the electrical plug is not connected to a switch which turns power off when lights are turned off.
3. Be sure you have inserted the trimmer properly into the charging stand, that all connections are secure, and that the trimmer switch is in the “OFF” position.
FOR HOUSEHOLD USE ONLY
OPERATING INSTRUCTIONS:
1. Before using your trimmer for the first time, insert the cord into the trimmer and then plug into wall outlet and charge it for 16 hours. Always place the trimmer in the base with the ON/OFF switch in the OFF position.
2. Always check to see if the charging light is on when the cord is connected to the trimmer and the unit is not in use.
3. Plug unit into any wall outlet (at the volt­age listed on the label affixed to the adapter.
4. The trimmer can remain plugged into the power source at all times without dam­age to the battery.
5. If, while using the trimmer without the cord, the charge seems to be running down, simply put ON/OFF switch in OFF position. Then, insert cord into the trimmer and plug into wall outlet. Switch to ON position and use as a corded trimmer.
6. The charging stand may become warm while charging. This is normal.
7. The adapter may become warm while charging — this is normal.
GUIDE DE DÉPANNAGE
Si la tondeuse rechargeable ne semble
pas vouloir charger, effectuez les points
dans une prise de courant et remettez la
tondeuse en marche pour l’utiliser avec le
cordon.
GETTING STARTED:
OUTLINING YOUR BEARD
1. It is always best to begin with a clean, slightly damp beard.
2. After you have combed through your beard in the direction it grows naturally, you will want to outline the desired shape, beginning under your jawline.
3. Begin defining your beard’ s shape under your chin and work upward on each side of your face toward your ears. Then define the upper outline of your beard across your cheeks, past your sideburns and toward your hairline.
TYPES OF BEARDS/MUSTACHES
Loading...