Conair LWD1C Instruction Manual

Page 1

REPLACEMENT PART:

This shaver uses the following replacement parts, which can be ordered directly from Conair by calling customer service at 1-800-3-CONAIR.

CSP21 Replacement Foil and Cutter

BATTERY OPERATED

Twin Foil Shaver

SERVICE CENTRE

CONAIR CONSUMER PRODUCTS INC. 100 Conair Parkway

For more information on any Conair product call: 1-800-472-7606

Visit our Web site: www.conaircanada.ca Consumer Call Centre E-mail: Consumer_Canada@Conair.com

12CN137997

IB-11931

Have a Question?

Please do not return this product

to the retailer.

Call Us First!

Our customer service and product experts

are ready to answer ALL your questions.

Please call our TOLL-FREE

customer service number at:

1-800-472-7606

or visit us online at

www.conaircanada.ca

INSTRUCTIONS FOR CARE AND USE

MODEL LWD1C

Page 2

HOW TO CLEAN YOUR SHAVER

1. Make sure unit is in the “OFF” position before cleaning your shaver.

2. Hold shaver head and lift up from the back, (FIG.1) then press foil frame release buttons on each side and lift up (the cutter is now in view). Be careful not to push on the foils. They are delicate and can easily be damaged.

SHAVING YOUR UNDERARMS

1. Prepare your underarms for wet or dry shaving. (Be sure that your skin is clean and free of deodorant).

2. Turn the shaver on.

3. Lift your arm until the skin under the arm stretches slightly.

4. Use the trimmer portion first to remove any long hair, stroking trimmer against the direction of hair growth.

5. Hold the shaver so that it is in full contact with your skin, and shave with gentle strokes.

6. It is important to press lightly. Pressing too hard may lead to skin irritation.

7. When finished shaving, turn the shaver off. Important: After several uses, you will be able

Transparent cover

Pop-up button

Press Here

FIG. 1

3. Rinse the shaver cutter and foil frame under

running water or in a sink. Do not use hot water. to determine the optimum shaving method for your underarms.

Use only warm or cold water.

4. After wet cleaning, allow the foil frame and

cutters to air-dry before closing foil frame and

shaver head. Replace shaver head back onto the

shaver until it clicks into place. Wipe the surface

of the main unit with a dry towel. Do not dry the

foil area. Let the shaving head air-dry.

5. The cutter can also be cleaned with a

cleaning brush.

Page 3

REPLACING THE POP-UP TRIMMER ASSEMBLY

Note: we do not recommend replacing the trimmer assembly yourself. Take or send the shaver to a Conair service center because this requires a special tool for replacement. For most users, this trimmer will stay sharp for as long as you own your shaver.

LIMITED TWO YEAR WARRANTY

Conair will repair or replace (at our option) your unit free of charge for 24 months from the date of purchase if the appliance is defective in workmanship or materials. To obtain service under this warranty, return the defective product to the service center listed below that is nearest you, together with your purchase receipt and $3.00 for postage and handling. California residents need only provide proof of purchase and should call 1-800-3660937 for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 24 months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 24 MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER.

Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

For shaving tips and information on Conair appliances call: 1-800-3-CONAIR or visit us on the web at www.conair.com

Page 4

12. Do not mix old and new batteries. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel cadmium or Nickel Metal Hydride) batteries.

CAUTION

Do not immerse any part of the unit in water or other liquid. The outer foils and cutters are delicate and must be handled very carefully.

BEFORE SHAVING

1. Before wet shaving, you may wish to prepare your legs and underarms with shaving cream or soap. If a soapy lather is applied to the skin, the shaver will glide smoothly over the skin and clean away oil residue while at the same time removing hair. Caution: DO NOT use shaving gels, as

these products can clog your shaver foils.

2. When dry shaving, be certain that your skin is clean. If you have sensitive skin, you may want to apply talcum powder before and

INSTRUCTIONS FOR USE

1. Slide the main switch up to the ON position.

2. After each shave, switch the unit off and clean shaver head.

SHAVING YOUR LEGS/BIKINI AREA

NOTE: Pushing the shaver against the skin too

hard will not allow the hairs to enter the foils and

be cut. Experience will show just the right

pressing to use to maximize performance.

1. Prepare your legs for wet or dry shaving.

2. Turn shaver on.

3. Shave with smooth, steady strokes up and

down your skin.

after you shave.

3. Clean your shaver after each use. This will insure the best performance. (Please refer to “How to Clean Your Shaver” section for further instructions.)

4. Keep the full shaving head in contact with

your skin.

5. For best results, shave against the direction of

hair growth.

6. The shaver has a bikini pop-up trimmer for

your complete shaving needs. To trim the bikini

area, use the handy pop-up feature to easily see

what you are trimming.

7. When you finish shaving, turn the shaver off.

Important: After several uses, you will be able to

determine the optimum shaving method for your

legs and bikini area.

Page 5

REPLACING THE

FOIL FRAME & CUTTER

Replace the foil frame when you find you have to push harder on the shaver to get a close shave, or if you have to go over your leg area more often to get a smooth result. It is also time to replace the foils if you

FIG. 4

experience skin irritation. Replacement time will depend on how often you use your shaver and how quickly your hair grows. Caution: Never replace the cutters without replacing the foils as well.

Lift

Press Here

FIG. 2

1. Remove the foil frame. (see FIG. 2)

3. Hold the new cutters firmly on the sides and guide them gently into the inner cutter mount one side at a time until they lock into place. (FIG. 4)

FIG. 5

4. Press firmly until the cutter snaps into place.

5. Replace the foil frame. (FIG. 5)

Hold Here

spring

FIG. 3

spring

2. Push one side of the cutters to unlock it and take out. (see FIG. 3) Be careful not to lose the small spring as it will be needed with the new cutters.

Page 6

OPERATING

INSTRUCTIONS

FOR HOUSEHOLD

USE ONLY

OPERATING INSTRUCTIONS

IMPORTANT

This shaver has been engineered to give you a clean, close, smooth shave. It requires 2 AAA batteries (not included). We recommend using longer lasting alkaline batteries in your shaver. If you are not going to use your shaver for a long period of time or if the batteries are dead, remove or replace the batteries from the unit. Use your shaver exclusively for three to four weeks so that your legs and underarms adjust to the shaver. At first, your shave might not be as close as you expect. However, this is normal. It takes time for your skin and hair to adjust to the new procedure

1. Remove the battery compartment cover by pushing in and down toward the bottom of the shaver.

2. Align the two AAA batteries with the positive and negative positions indicated inside the battery compartment. Being careful not to bend the clips, insert the negative end of each battery first so it will slip easily into place.

3. Return the battery cover to its original position by pushing it in and up until you hear a small click as it locks into place.

4. To use your shaver, remove the transparent cover and push ON/OFF switch upwards to the ON position.

5. After you finish using your shaver, push and for you to learn how the effectively use the shaver. Caution: Most blade users will push too hard and therefore not get a satisfactory shave. You must press gently so the hair can get into the holes of the foil pressing too hard makes the hair flat. Please be patient; use your shaver 10 to 12 times before you judge its performance.

down on the ON/OFF switch to turn the shaver off.

6. Ensure the batteries are installed correctly

with regard to polarity (+ and -).

7. Remove the batteries if the batteries are no

longer functional or if the shaver is left unused for an extended period of time.

8. Clean the battery contacts and also those

of the device prior to battery installation.

9. Remove used batteries promptly.

10. Always purchase the correct size and grade

of battery most suitable for the intended use.

11. Replace all batteries of a set at the same

time.

Page 7

6. If the body of the shaver becomes dirty, wipe off with a damp cloth and mild detergent or soap. Never use thinners, other solvents, or any harsh cleaners.

7. Once dried, carefully place the protective cap on.

CAUTION

1. When shaking off excess water, hold the main unit firmly to prevent releasing the head assembly or dropping the unit.

2. Do not use a dryer or heater to dry the shaver. This may result in malfunction or damage to the shaver.

Page 8

Congratulations on the purchase of your new ladies dual foil shaver. For maximum satisfaction when using this quality product, please take a minute to read the following operating and care instructions. Thank you for choosing Conair, the #1 brand in personal care appliances.

SAVE THESE

INSTRUCTIONS

WARNING

1. Women whose skin is sensitive to cosmetics or easily irritated by shaving, or who suffer from a skin allergy, should test one section of the leg or arm before using the shaver.

2. The foils are thin and precisely finished

pieces. Do not press hard against the foils, or drop foils. A warped or distorted foil will produce poor shaving results. Also a damaged foil may cause skin injury. A damaged foil should be replaced immediately.

3. When cleaning, use cold or warm water. Do not use hot water, sea water, or cleaners, as they can cause damage to the waterproof seals.

4. Rinse the shaver head only, do not submerge the entire unit in water.

5. To prevent possible damage to the foils and the cutter, women who use underarm deodorant must thoroughly clean and air-dry the foil and cutter after each use. Failure to do this may result in corrosion of the cutters.