Conair Combo Cut HCT300GB Instructions For Care And Use

Page 1
Desenrede el cabello, luego coja la
recortadora cómodamente en su mano. Ya
está listo/a para empezar.
CORTES MEDIANOS A LARGOS
Empiece cortando poco cabello, hasta
acostumbrase a cada guía. Use la guía más
larga para empezar, luego use guías más cortas
para acortar el cabello.
(3 mm)
• Guía mediana-corta (No.2) - corta el cabello
a 1/4" (6 mm)
• Guía mediana-larga (No.3) - corta el cabello a
3/8" (9.5 mm)
• Guía larga (No.4) - corta el cabello a 1/2"
(12.5 mm)
• Guía larga (No.5) - corta el cabello a 5/8"
(16 mm)
• Guía larga (No.6) - corta el cabello a 3/4"
(19 mm)
• Guía para la oreja izquierda - delinea la oreja
izquierda
• Guía para la oreja derecha - delinea la oreja
derecha
Para instalar la
guía, sosténgala
cabeza arriba y
engánchela en la
parte inferior de la
cuchilla.
Para sacar la
guía, cójala según
se indica, y jálela
hacia arriba y
fuera.
STOP. COMB. CHECK.
For best results, do as the professionals do: comb hair often, and check clipping results as you comb. This way you avoid uneven sides, bangs, neckline, etc.
SHORT CUTS TO PERFECT
FLAT TOPS, CREW CUTS, ETC.
Always cut from the back of the neck to the crown, using the longest comb setting.
Hold the comb attachment flat against the head and slowly move the clipper up through the hair. Use the same technique for the sides, cutting from the bottom to the upper side of the head.
For the front to the crown, cut the hair against the direction in which it grows. Then even it up with the sides. For a flat top, use the flat comb, not the attachment comb. Just cut hair on top of the head over flat comb. (see below). To taper hair down to the neckline, use attachment comb #1. Comb hair and check for uneven spots. Outline sideburns and neck areas (see “Outlining”).
To begin cutting hair:
1. The hair should be combed in its natural direction.
2. Using the largest attachment comb, trim sides from the bottom upward. Hold clipper lightly against the hair with teeth of the attach­ment comb point­ing up ward, yet flat against the head. Gradually lift the clip­per upward and out­ward through the hair, trimming just a little at a time.
Repeat around sides and back of head.
If you want hair to be even shorter: A) Apply more pressure to the head with the attachment comb that is in place. This takes a little practice, of course. OR B) Just switch to a shorter attachment comb.
11. Do not use this appliance with a damaged or broken comb or with teeth missing from the blades, as injury may occur.
12. Avoid skin contact with moving blades.
13. When using the appliance with its cord, be mindful of tangles or kinks in the cord. If the cord does become tangled during use, turn the unit off and straighten cord before operating again.
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
This appliance is used on Alternating Current 120V AC (60 hertz) only. To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in the polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. Do not attempt to defeat this safety feature.
Your new Conair
® haircut kit has everything
you need to achieve professional haircuts at home. It features a powerful clipper with adjustable taper control and high carbon steel blades for cutting precision. Also included are 8 attachment combs 1/8"
(3.175mm)
, 1/4"
(6.350mm)
, 3/8"
(9.525mm)
,
1/2"
(12.700mm)
, 5/8" (15.875mm)
, 3/4"
(19.050mm)
for different hair lengths (left and right ear combs), barber scissors, storage case, a barber comb with straight teeth, styling comb with angled teeth and 3 styling clips to assist you in cutting longer hair styles. It also comes with lubricating oil, a cleaning brush and a blade guard for easy maintenance of the clipper blades.
This kit also has a fine line trimmer that is great for necks, sideburns, goatees and mustache trimming.
THE CONAIR GUIDE
TO CUTTING HAIR AT HOME
Before you start:
1. Inspect your clipper. Make sure it’s free of hair and dirt, properly oiled, and running smoothly.
2. Place a towel or cape around the neck of the person.
3. Seat the person so that his or her head is at your eye level.This gives you greater visibility and control.
4. First, comb hair until it’s tangle-free. Then hold clip­per in a comfortable grip. Now you’re ready to cut.
MEDIUM TO LONG CUT
To begin with, cut only a small amount of hair until you become used to the length each attach­ment leaves the hair. Try the longest attachment on the clipper first. If you want a shorter cut, you can then use shorter combs.
• Short attachment comb (numbe
r 1) cuts hair to
1/8” (3.175mm).
• Medium-Short attachment comb (number 2) cuts hair to 1/4" (6.350mm).
• Medium-Long attachment comb (number 3) cuts hair to 3/8" (9.525mm).
• Long attachment comb (number 4) cuts hair
Remember, it’s better to leave too much hair than too little. For longer hair on top, use the barber comb and lift hair on the top of the head, cutting over the comb. Or hold the hair between the fingers and cut to desired length. Always working from the front to the back of the head, gradually cut the hair shorter by reducing the space between the comb or fingers and the head. Comb often to check for uneven strands, and to get rid of trimmed hair.
OUTLINING:
Outlining requires no attachments. Comb hair into the desired style. Position the clipper between the sideburns and the ear (see below), making sure the corner edge of the blade is against the hairline. With the outline of the hair as your guide, slowly move the clipper over, around and behind the ears. For the back of the neck and the sideburns, hold the clipper upside down (see above) and, holding it against the skin at the length desired, move the clipper downward.
1. An appliance should never be left unattended when plugged in.
2. This appliance should not be used by, on, or near children or individuals with certain disabilities.
3. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
4. Never operate this appliance if it has a
damaged cord or plug, if it is not working properly, if it has been dropped, damaged, or dropped into water.
Return the appliance to service center for examination and repair.
5.Keep the cord away from heated surfaces.
6.Never operate the appliance with the air opening blocked or while on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair and the like.
7.Never drop or insert any object into any opening.
8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
9. Always attach plug to appliance first, then to outlet. To disconnect, turn all controls to “off”, then remove plug from outlet.
10. Do not place appliance on any surface while it is operating.
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, follow basic safety precautions, including the following:
READ ALL INSTRUCTIONS
BEFORE USING
KEEP AWAY FROM WATER
DANGER — Any appliance is
electrically live, even when the switch is off. To reduce the risk of electric shock:
1. Do not reach for an appliance that has fallen into water. Unplug immediately.
2. Do not use while bathing or in the shower.
3. Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
4. Always unplug this appliance from the electrical outlet immediately after using.
5. Unplug this appliance before cleaning.
DO NOT REACH
INTO THE WATER
WARNING
—To reduce the risk of burns, electric shock, fire, or injury to persons:
to 1/2" (12.700mm).
• Long attachment comb (number 5) cuts hair to 5/8"
(15.875mm).
• Long attachment comb (number 6) cuts hair to 3/4"
(19.050mm).
• Left ear attachment comb lightly tapers over left ear.
• Right ear attachment comb lightly tapers over right ear.
Attach combs by holding them teeth up, then snapping onto the bottom of the clipper blade.
To remove comb attachments, place index fin­ger and thumb as illustrated; then pull out and up.
NOTE: Never push or shove the clipper through the hair to make it move more quickly. Professional experience shows that the clipper works most efficiently when it cuts through the hair at its own speed.
To Align Blades:
1. Add two or three drops of Conair Lubricating Oil (included).
2.Turn clipper on for a min­ute to disperse oil evenly over blades, then turn off.
3. Unplug clipper and slightly loosen screws. (See FIG. 2)
4. Position the extreme left-hand tooth of the top blade so that it either covers or appears on the left of the first small tooth on the bottom blade.
5. Make sure that the big tooth on the bottom blade touches the extreme right hand tooth of the top blade.
USER-MAINTENANCE
INSTRUCTIONS
CARE OF YOUR CLIPPERS
IF YOU DETERMINE THAT BLADE ALIGNMENT IS INCORRECT:
Conair® hair clippers are carefully inspect­ed to insure that the blades are in per­fect alignment. Of course you will need to realign the blades after removal for clean­ing or replacement, or if they should be knocked out of alignment. How can you tell if blades need realigning? Simply match them up, point for point, to conform with FIG. 1 below:
To prevent the clipper from contacting the skin or cutting too closely, make certain that the end top blade teeth are 1/32" to 1/16" back from bottom blade.
FIG. 1
FIG. 2
PERFECTOS CORTES CON
CORONILLAS PLANAS, CORTES
MILITARES ETC.
Siempre corte el cabello desde la nuca
hasta la coronilla, usando la guía más larga.
Sostenga la guía contra la cabeza y mueva
la recortadora lentamente hacia arriba. Use
la misma técnica para los lados, cortando
desde abajo hasta la parte superior lateral
de la cabeza.
Para la parte delantera, corte el cabello en
dirección opuesta al crecimiento del pelo,
luego iguale los lados.
Para obtener una coronilla plana, use un
peine plano en vez de una guía y corte el
cabello encima del peine (véase el dibujo).
Para cortar el cabello en la nuca y en
las patillas, utilice la guía No.1 (Véase
“Contorneo”).
NOTA: Nunca empuje la recortadora para
que corte más rápidamente. La experiencia
profesional demuestra que funciona mejor
cuando corta a su propia velocidad.
Empezar el corte de
cabello:
1. Peine el cabello
en la dirección de su
crecimiento natural.
2. Empiece el recorte
en un lado de la cabeza,
usando la guía más
larga, y cortando desde
abajo hasta arriba.
Sostenga la recortadora
ligeramente contra el
cabello, con los dientes
de la guía apuntando
hacia arriba y planos
contra la cabeza. Pase la
recortadora en el cabello
gradualmente hacia
arriba y hacia fuera, cor-
tando un poco cabello
cada vez.
Haga lo mismo en el
otro lado y atrás de la
cabeza.
Si quiere un corte de
cabello aún más corto:
A) Aplique más presión.
Esto necesita al principio
un poco de práctica.
O
B) Utilice una guía más
corta.
productos en aerosol (spray) o donde se esté
administrando oxígeno.
10. Nunca bloquee las aberturas de aire o
coloque el aparato en una superficie blanda,
como una cama o un sofá, donde se puedan
obstruir. Mantenga las aberturas libres de
pelusas, cabellos y elementos similares.
11. Siempre conecte el cable al aparato
antes de conectarlo al tomacorriente.
Siempre apague el aparato (OFF) antes de
desconectarlo.
12. Evite que las cuchillas toquen la piel
cuando están moviendo.
13. Siempre asegúrese que el cable del
aparato no esté enredado. Si el cable se
enreda o se enrolla mientras está usando
el aparato, apáguelo inmediatamente y
enderece el cable.
GUARDE ESTAS
INSTRUCCIONES
INSTRUCCIONES
DE USO
Este aparato fue diseñado para uso
doméstico. Úselo con Corriente Alterna de
120V (60Hz) únicamente. El cable de este
aparato está dotado de una clavija polarizada
(una pata es más ancha que otra). Como
medida de seguridad, se podrá enchufar
de una sola manera en el tomacorriente. Si
no entrara por completo, inviértela. Si aún
no entrara completamente, comuníquese
con un electricista. No intente vencer esta
función de seguridad.
El Juego de Peluquería [combo] cut™ de
Conair
®
tiene todo lo que usted necesita
para lograr cortes de cabello profesionales
en su casa. Incluye una recortador a para
el cabello con palanca reguladora ajustable
y cuchillas de acero duro para un cortado
preciso. 8 peines-guías (incluso uno para la
oreja izquierda y uno para la oreja derecha)
permiten lograr distintos largos de recorte: 3
mm (1/8"), 6 mm (1/4"), 9.5 mm (3/8"), 12.5
mm (1/2"), 16 mm (5/8"), 19 mm (3/4"), oreja
izquierda y oreja derecha. También incluye
tijeras de peluquero, una práctica caja de
almacenaje, un peine con dientes rectos,
un peine con dientes ladeados, 3 pinzas,
aceite lubricante, un cepillo de limpieza y
un protector de cuchillas para mantener las
cuchillas en condición óptima.
Por fin, su conjunto de peluquería también
incluye una recortardora de detalle, ideal
para cortar el cabello en la nuca y las sienes,
así como para cortar la perilla y el bigote.
GUÍA DE CONAIR PARA CORTAR EL
CABELLO EN SU CASA
Antes de empezar:
1. Inspeccione el aparato para asegurarse
que esté libre de cabello y polvo, que fun-
cione correctamente y que las cuchillas
estén lubricadas.
2. Oque una toalla o una capa de peluquero
alrededor del cuello de la persona a quien le
va a cortar el cabello.
3. Siente a la persona de manera que su
cabeza esté al nivel de sus ojos para mayor
visibilidad y control.
Recuerde: Es mejor dejar el cabello demasiado
largo que demasiado corto. Si quiere dejar
el cabello más largo encima de la cabeza,
utilice el peine de peluquero o sus dedos para
levantar el cabello y córtelo a lo largo deseado.
Trabaje siempre desde adelante hacia atrás
de la cabeza y corte el cabello poco a poco,
reduciendo el espacio entre sus dedos (o el
peine) y la cabeza. Peine con frecuencia para
verificar que no hay mechones disparejos y
para eliminar los recortes.
CONTORNEO
El contorneo no requiere accesorios. Primero,
peine el cabello como desea. Coloque la
recortadora entre la patilla y la oreja (véase
el dibujo), posicionando la esquina de la
cuchilla contra el nacimiento del pelo. Mueva la
recortadora lentamente sobre, alrededor y atrás
de las orejas, siguiendo el contorno del cabello.
Para cortar el cabello en la nuca y en las sienes,
sostenga la recortadora al revés (véase el
dibujo), colóquela contra la piel al nivel deseado
y muévala hacia abajo.
DETÉNGASE. PEINE. VERIFIQUE.
Para lograr resultados óptimos, siga el ejemplo
de los profesionales: Peine el cabello con
frecuencia para verificar los resultados. Esto
evitará tener lados, flequillos o líneas de nuca
disparejos.
NO TRATE DE ALCANZAR
EL APARATO EN EL AGUA
ADVERTENCIA — Para
reducir el riesgo de quemaduras, electro-
cución, incendio o heridas:
1. Nunca deje este aparato desatendido
mientras esté conectado. No jale, doble o
enrolle el cable alrededor del aparato.
2. Este aparato no debería ser usado por,
sobre o cerca de niños o personas con alguna
discapacidad.
3. Use este aparato únicamente con el
propósito para el cual fue diseñado y
solamente según las instrucciones. Sólo use
accesorios recomendados por el fabricante.
4. Nunca utilice el aparato si el cable o la
clavija estuviesen dañados, si no funcionase
correctamente, si hubiese caído, si estuviese
dañado o si hubiese caído al agua. Regréselo
a un centro de servicio autorizado para que
lo examinen y lo reparen.
5. Mantenga el cable alejado de las
superficies calientes.
6. Nunca deje caer ni inserte un objeto en
ninguna de las aberturas.
7. No coloque el aparato en ninguna
superficie mientras esté funcionando.
8. No utilice este aparato con un peine-
guía roto o lastimado o si faltaran dientes
a la cuchilla. Esto podría provocar una
herida. Asegúrese que las cuchillas estén
debidamente alineadas antes de usarlo
(véase “Instrucciones de mantenimiento”).
9. No utilice este aparato en exteriores, ni
lo haga funcionar donde se estén usando
MEDIDAS DE
SEGURIDAD
IMPORTANTES
Siempre que use aparatos eléctricos,
especialmente en la presencia de niños, debe
tomar precauciones básicas de seguridad,
entre las cuales las siguientes:
LEA TODAS LAS
INSTRUCCIONES ANTES DE
USARLO
MANTÉNGALO ALEJADO
DEL AGUA
PELIGRO — Cualquier aparato
enchufado permanece bajo tensión, aunque
el interruptor esté apagado. Para reducir el
riesgo de muerte o herida por descarga:
1. Desconecte el aparato antes de limpiarlo.
2. No coloque ni guarde el aparato donde
pueda caer o ser empujado a una bañera
o un lavabo.
3. No lo use en el baño o la ducha.
4. No coloque el aparato ni lo deje caer al agua
u otro líquido.
5. No intente alcanzar un aparato que hubiese
caído al agua. Desenchúfelo inmediatamente.
6. Siempre desconecte el aparato inmediata-
mente después de usarlo.
Para alinear las cuchillas:
1. Ponga unas 2 ó 3 gotas
del aceite lubricante provisto
en las cuchillas.
2. Enciende la recortadora
durante un minuto
para repartir el aceite
uniformemente en las cuchillas, luego
apáguelo.
3. Desconecte el aparato y afloje
ligeramente los tornillos. (Fig.2)
4. Posicione el extremo diente izquierdo de
la cuchilla grande de tal manera que cubra
o esté a la izquierda del primer diente
pequeño de la cuchilla pequeña.
5. Asegúrese que el diente grande de la
extremidad derecha de la cuchilla pequeña
toque el diente de la extremidad derecha
de la cuchilla grande.
INSTRUCCIONES DE
MANTENIMIENTO
RECORTADORA PARA
EL CABELLO
ALINEACIÓN DE LAS CUCHILLAS
Las recortadoras de Conair
®
son
inspeccionadas para asegurarse que las
cuchillas estén perfectamente alineadas.
Usted necesitará alinearlas nuevamente
después de extraerlas para limpiarlas o
reemplazarlas o si se desalinearon por
un golpe. Para determinar si las cuchillas
necesitan alinearse de nuevo, simplemente
hágalas coincidir como lo indican la figura
que se encuentra a continuación.
Para evitar que la recortadora corte el pelo
demasiado corto o que las cuchillas toquen
la piel, asegúrese que la parte superior de
la cuchilla grande esté a una distancia de
1 mm a 1.5 mm de la cuchilla pequeña.
FIG. 1
FIG. 2
Instructions for Care and Use
MODEL HCT300GB
20 PIECE
HAIRCUT KIT
Instrucciones de uso y mantenimiento
MODELO HCT300GB
20 PIEZAS
JUEGO DE PELUQUERÍA
ACEITE ESPECIAL
Para mantener las cuchillas de su
recortadora en condición óptima, lubríquelas
después de tres o cuatro cortes de cabello.
Aplique unas cuantas gotas de aceite
lubricante en los dientes de las cuchillas,
encienda la recortadora durante un minuto,
luego apáguela. El aceite lubricante provisto
ha sido específicamente diseñado para las
recortadoras de alta velocidad de Conair
®
.
Porque es el aceite adecuado, no reducirá
la velocidad de las cuchillas. Nunca use
otro aceite para lubricar las cuchillas de
su recortadora. No hay ningún substituto al
aceite de Conair. Mantenga el aceite fuera
del alcance de los niños.
SPECIAL OIL
To maintain the blades of your Conair
®
clipper, oil them after every three or four haircuts. Gently place a few drops of oil on the teeth of the blades, using the special Conair oil included with your set. Turn the clipper on for a minute, then turn off. This light, natural oil was formulated specifically for the Conair
®
high-speed clipper. Be cause it is the right oil to use, it will not slow down the blades. Never use any other product. There is no substitute for Conair oil. Keep oil away from children.
08PG125_hc300gb_IB.indd 108PG125_hc300gb_IB.indd 1 10/1/08 2:54:14 PM10/1/08 2:54:14 PM
Page 2
Conjunto de 4 guías: 3mm (1/8"), 6mm (1/4"), 9mm (3/8"), 13mm (1/2"). Compatible con todas las recortadoras. COMB-10 $5.00 Conjunto de 2 guías: oreja izquierda y oreja derecha. Compatible con todas las cortadoras. COMB-11 $1.75 Guía de 25mm (1”). Compatible con todas las recortadoras. COMB-12 $1.75 Conjunto de 3 guías: 16mm (5/8"), 19mm (3/4") 22mm (7/8"). Compatible con todas las recortadoras. COMB-13 $5.00 Cepillo para el cuello HCNB-1 $1.50 Capa de vinilo blanca deluxe con cierre velcro CAPE-1 $5.00 Aceite lubricante (paquete de 3) HC OIL $2.00 DVD instructivo DVD-1 $5.00 Tijeras de peluquero SC-1 $2.00 Juego de cuchillas para el modelo HCT300GB BLD-8 $6.50 Protector de cuchillas HC-1 $1.00 Pinzas (paquete de 3) CLP-1 $1.50
MANTÉNGALO ALEJADO
DEL AGUA
Todos sabemos que no se debe mezclar la electricidad y el agua. Pero ¿Sabe usted que un aparato eléctrico permanece bajo tensión aunque esté apagado? Si está conectado, hay corriente. Por lo tanto, siempre desenchufe sus aparatos eléctricos después de usarlos.
SIEMPRE DESENCHUFE LOS
APARATOS PEQUEÑOS
ADVERTENCIA: SI CREE
QUE NO HAY CORRIENTE
CUANDO EL APARATO ESTÁ APAGADO, ESTÁ
EQUIVOCADO
GARANTÍA LIMITADA DE CINCO AÑOS
Conair reparará o remplazará (a su opción) su aparato sin cargo por un período de 60 meses a partir de la fecha de compra si presentara defectos de materiales o fabricación. Para obtener servicio técnico bajo esta garantía, regrese su aparato al Centro de Servicio indicado a continuación, junto con su recibo de compra y un cheque o giro postal de $3.00US por gastos de manejo y envío. Los residentes de California sólo necesitan dar una prueba de compra y deben llamar al 1-800-366­0937 para recibir instrucciones de envío. En ausencia del recibo de compra, el período de garantía será de 60 meses a partir de la fecha de fabricación.
CUALQUIERA GARANTÍA, OBLIGACIÓN O RESPONSABILIDAD IMPLÍCITAS, INCLUYENDO PERO NO LIMITADAS A LA GARANTÍA IMPLÍCITA DE COMERCIABILIDAD Y APTITUD PARA UN PROPÓSITO ESPECÍFICO, ESTARÁN LIMITADAS POR LOS 60 MESES DE LA PRESENTE GARANTÍA ESCRITA. Algunos
Estados no permiten limitaciones sobre la duración de una garantía implícita, de modo que las limitaciones mencionadas pueden no regir para usted.
CONAIR NO SERÁ RESPONSABLE EN NINGÚN CASO POR ALGÚN DAÑO ESPECIAL, INCIDENTAL O CONSECUENTE DEBIDO AL INCUMPLIMIENTO DE ESTA O CUALQUIER OTRA GARANTÍA, EXPRESA O IMPLÍCITA.
Algunos Estados no permiten la exclusión o limitación de daños especiales, incidentales o consecuentes, de modo que las limitaciones mencionadas pueden no regir para usted. Esta garantía le otorga derechos legales específicos y usted puede tener otros derechos que varían de un Estado a otro.
CENTRO DE SERVICIO:
© 2008 CONAIR CORPORATION CONAIR CORPORATION Service Department 7475 North Glen Harbor Blvd. Glendale, AZ 85307
Conair Corporation
150 Milford Rd.
East Windsor, NJ 08520
PRECAUCIÓN: Nunca jale, tuerce o enrolle
el cable alrededor del aparato. Cuando no usa el aparato, deje el cable libre al lado del aparato.
Nuevamente, gracias por comprar un producto de Conair.
Las cuchillas de su recortadora son de acero duro inoxidable y logran resultados precisos y profesionales. Si siente que las cuchillas tironean o enganchan el pelo, significa que están perdiendo el filo y debe reemplazarlas lo más pronto posible.
También se deben cambiar las guías si se pierden o se dañan. Es más fácil cortar el pelo con exactitud profesional cuando se tienen las herramientas adecuadas.
Conair también fabrica una variedad de accesorios para cortar el cabello. Si su juego de peluquería no los incluye, los puede pedir por separado.
Guías para contornear la oreja izquierda y derecha brindan un corte de precisión sin esfuerzo. Las pinzas sostienen el cabello. El peine regular permite contornear o cortar el cabello en ángulo. La capa de peluquero asegura un corte cómodo y limpio y el cómodo bolso de almacenamiento mantiene todo sus accesorios en el mismo lugar.
También puede ordenar el DVD instructivo de 30 minutos “Corte de cabello en casa” con instrucciones fáciles de seguir. El DVD muestra las técnicas básicas del corte de cabello y presenta cuatro atractivos cortes paso a paso. Le dará la confianza y los conocimientos que necesita para cortar el cabello de todos los miembros de su familia.
PALANCA REGULADORA
Al igual que las recortadoras profesionales, su recortadora está equipada con una palanca reguladora ajustable al nivel del pulgar, la cual permite controlar lo largo del recorte a medida que corta el cabello.
La palanca reguladora permite cortar el cabello más corto o más largo, sin tener que usar un peine-guía. Para cortar el cabello más corto, deslice la palanca hacia arriba. Para cortar el cabello más largo, deslice la palanca lentamente hacia abajo. El ajuste más largo dejará el cabello tan corto como la guía más corta.
El usar la palanca reguladora prolongará la vida útil de las cuchillas, puesto que nunca usan el mismo ángulo para cortar. Su recortadora puede perder velocidad si recortes de cabello están trabados en las cuchillas. Para limpiar las cuchillas sin tener que sacarlas, utilice el cepillo de limpieza provisto o mueva la palanca reguladora desde arriba hasta abajo varias veces.
Hacer esto después de cada uso, especialmente cuando se corta mucho cabello, mantendrá las cuchillas en condición óptima. Si la recortadora dejara de funcionar, y que esto no soluciona el problema, inspeccione las cuchillas. Cámbielas si están embotadas. Puede pedir nuevas cuchillas por correo, mandando el formulario de pedido adjunto y un cheque o un giro postal de $6.50US (incluye gastos de envío y manejo con pedidos mínimos de $10.00US) a la dirección siguiente.
Corte más largo
Corte más corto
Modelo
COMB-10
Modelo
COMB-11
Modelo COMB-13
Modelo COMB-12
Modelo HCNB-1
Modelo
CAPE-1
Modelo
HC OIL
Modelo
SC-1
Modelo
BLD-8
Modelo
HC-1
Modelo
CLP-1
Modelo
DVD-1
LWD375RCS Satiny Smooth
®
Rasuradora de lujo para mujeres, para uso en seco o con agua.
Cuchilla
Compartimiento de la pila
Cubierta del compartimiento de la pila
Botón de encendido/ apagado
RECORTADORA DE DETALLE
Model MT141
FUNCIONAMIENTO DE LA RECORTADORA DE DETALLE
1. Abra el compartimiento de la pila, girando la cubierta hacia la izquierda, luego jalándola hacia abajo. Ensarte una pila alcalina de tipo AA, el polo negativo primero. Para lograr un rendimiento óptimo, le recomendamos que utilice una pila alcalina. Saque la pila del aparato si no lo va a usar durante un tiempo prolongado o si la pila está muerta. Esto prolongará la vida útil del aparato.
2. Después de instalar la pila, cierre el compartimiento y encienda el aparato (ON).
3. Antes de dar forma a su bigote, péinelo en dirección del crecimiento del pelo. Sostenga el aparato en forma muy recta y acerque las cuchillas al bigote para empezara cortar.
4. Para limpiar las cuchillas, apague el aparato (OFF) y empuje las cuchillas hacia arriba con el pulgar. Esto facilitará la limp­ieza, puesto que el cabezal está montado en bisagras. Limpie los recortes de pelo con el cepillo de limpieza provisto o sop­lando sobre las cuchillas.
5. Empuje el cabezal hacia abajo hasta que haga clic. La recortadora de detalle es perfecta para cortar el cabello en la nuca, las patillas y la perilla. No fue diseñada para cortar barba. Para esto, utilice la recortadora para el cabello.
IB-8789
08PG125
NOVEDADES FASCINANTES
DE CONAIR
LIMITED FIVE YEAR WARRANTY
Conair will repair or replace (at our option) your unit
free of charge for 60 months from the date of pur-
chase if the appliance is defective in workmanship
or materials.
To obtain service under this warranty, return the defec-
tive product to the service center listed below that is
nearest you, together with your purchase receipt and
$3.00 for postage and handling. California residents need
only provide proof of purchase and should call 1-800-
366-0937 for shipping instructions. In the absence of a
purchase receipt, the warranty period shall be 60 months
from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR
LIABILITIES, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTY OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, SHALL BE
LIMITED IN DURATION TO THE 60 MONTH DURATION
OF THIS WRITTEN, LIMITED WARRANTY. Some states
do not allow limitations on how long an implied war-
ranty lasts, so the above limitations may not apply
to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES
FOR BREACH OF THIS OR ANY OTHER WARRANTY,
EXPRESS OR IMPLIED, WHATSOEVER. Some states
do not allow the exclusion or limitation of special,
incidental, or consequential damages, so the above
limitation may not apply to you.
This warranty gives you specific legal rights, and you
may also have other rights, which vary from state to
state.
SERVICE CENTER:
©2008 CONAIR CORPORATION
Service Department
7475 North Glen Harbor Blvd.
Glendale, AZ 85307
Bottom
Blade
Top
Blade
NOTE: Never pull on the clipper cord.
Never twist or wrap the cord around the
clipper. Lay it flat with the cord coiled up
when not in use.
KEEP AWAY FROM WATER
Everyone knows that electricity and water
are a dangerous combination. But did you
know that an electric appliance is still
electrically alive even if the switch is off?
If the plug is in, the power is on. So when
you are not using your appliances, keep
them unplugged.
ALWAYS UNPLUG
SMALL APPLIANCES
WARNING:
IF YOU THINK
THE POWER IS OFF
WHEN THE SWITCH
IS OFF,
YOU'RE WRONG.
Once again, thanks for buying a
Conair product.
Your Conair
®
clipper blades are made of
high carbon stainless steel. They are
engineered for precise, professional results.
If blades feel like they are pulling or grab-
bing hair, it means they are losing their
sharpness and should be replaced as soon
as possible.
Attachment combs should also be replaced
if they are lost or broken. It is easier to cut
hair with the accuracy of a pro when the
necessary tools are at your fingertips.
Conair makes a variety of accessories
for different haircut kits. If your haircut kit
does not include them, you may want to
consider adding them to your professional
haircutting tools.
Left and right ear attachment combs
provide effortless, precise cutting around the
ears. Styling clips hold hair in place when you
are sectioning hair. A styling comb makes it
easy to taper or cut hair at an angle. A barber
cape ensures a comfortable and neat haircut
and a convenient storage case keeps all your
essentials in one place.
Last but not least, an easy-to-follow
30-minute “Haircuts at Home” DVD is
available. It demonstrates basic haircut-
ting techniques and follows four popular
haircuts step by step. It will give you the
confidence and instruction you need to give
great looking haircuts to every member of
your family.
MODEL HCT300GB
5 DETENT ADJUSTABLE
TAPER LEVER
Just like professional clippers, the
Conair 5 position taper lever is positioned at
your thumb. You can hold the clipper
in your hand and adjust the lever at the
same time...while you’re clipping.
This taper lever eliminates the need for
an attachment comb because it lets you
gradually adjust the closeness of the cut.
For the closest cut and the shortest
hair, push taper lever up to position #1.
To increase cutting length, slowly push
lever down. If you push to the lowest
position, it will leave hair about the same
length as the short attachment.
Because a different cutting edge is used in
each setting, the taper lever lengthens the life
of your blades.
Packed-in hair can slow down any clipper.
To remove hair without removing the blades,
use the cleaning brush provided or gently
move the taper control to loosen packed-
in hair. If you do this after every clipping,
especially with heavy hair cutting, the blades
should remain free of cut hair. If clipper stops
cutting and this action doesn’t help, check
the blades. If they’ve become dull, replace
them. For new blades, send check or money
order for $6.50 (see order blank) which
includes postage and handling (If $10
minimum is met) to:
Conair Corporation
150 Milford Rd.
East Windsor, NJ 08520
Longer
Cut
Close Cut
HAIRCUT KIT REPLACEMENT PARTS & ACCESSORIES ORDER FORM
Pricing in
effect through June 1, 2009. Orders postmarked after this date
will be accepted, and the customer wil
l be notified if pricing has changed.
ITEM PART # PRICE QUANTITY AMOUNT
Subtotal
*Sales Tax
TOTAL
To avoid delays, please print clearly.
We must have a street address, as UPS cannot deliver to a P.O. box.
NAME____________________________________________________________________________
ADDRESS __________________________________________________ APT.________________
CITY _______________________________________________STATE _______ ZIP
TELEPHONE ( ) _____________________________________________________________
(We call only if we have a question
about your order.)
For information on other Conair® haircut kit parts call: 1-800-3-CONAIR.
Mail to:
Conair Corporation
Service Department
150 Milford Road
East Windsor, NJ 08520-9730
Enclose check or money order made payable to Conair. (We cannot accept cash, stamps or C.O.D. orders.) CT, IL, AZ, and PA residents
should add applicable state sales tax. Minimum order of $10.00 or a $2.00 handling charge will be added to order.
All prices include handling and return postage. Prices are subject to change without notice.
Prices are valid only for shipments within the Continental United States. Please allow 4-6 weeks for delivery.
Model COMB-10
Model COMB-11
Model COMB-13
Model COMB-12
Model HCNB-1
Model CAPE-1
Model HC OIL
Model SC-1
Model BLD-8
Model HC-1
Model CLP-1
CUT HERE
Model DVD-1
Set of 4 Attachment Combs:1/8”, 1/4”, 3/8”, 1/2”. COMB-10 $5.00
Fits all clippers
Set of 2 Attachment Combs: left ear and right ear. Fits all clippers COMB-11 $1.75
1" Comb fits all clippers COMB-12 $1.75
3 attachment combs: 5/8", 3/4", 7/8". Fits all clippers COMB-13 $5.00
Neck Brush HCNB-1 $1.50
Deluxe Black Vinyl Cape with Velcro Collar CAPE-1 $5.00
Lubricating Oil (pkg. of 3 tubes) HC OIL $2.00
Instructional DVD DVD-1 $5.00
Barber Scissors SC-1 $2.00
Blade Set for HCT300GB BLD-8 $6.50
Blade Guard HC-1 $1.00
Styling Clips (set of 3) CLP-1 $1.50
LWD375RCS Satiny Smooth
®
• Ladies deluxe, twin
foil, wet/dry shaver.
NEW
GMT400 SWITCHCUT
12 Piece Facial Grooming System
• Built-in 2 blade
system
• Slide the button,
switch the blades
Adjustable
Taper Lever
Switch
Trimmer
Blade
Battery
Compartment
Battery
Compartment
Cover
On/Off
Switch
FINE LINE TRIMMER
Model MT141
TO OPERATE TRIMMER
1. To insert battery, remove compartment
cover by turning bottom piece of trimmer
to the left, then pulling straight down.
Insert one AA alkaline battery, positive
end up (Alkaline batteries will ensure the
best performance and longest life for your
appliance.) If you are not going to use the
unit for a long period of time, or if the
battery is dead, remove the battery from
the unit. This will increase the life of your
trimmer.
2. After inserting battery, close bat tery com-
partment and turn unit to ON position.
3. To trim your mustache, use the
mustache comb to comb hair in the
direction of growth. Hold trimmer in an
upright position and bring the tip of the
blade straight into the mustache to trim.
4. To clean the trimmer, turn unit to OFF
position. Using your thumb, press upwards
against the blade. This will make it easy
to clean, since head cover is on a hinge.
Brush or blow hair clippings from the cut-
ter blade.
5. Close head cover until you hear a
click. This trimmer works well on side-
burns & necks as well as goatees and
mustaches. It is not designed for
beards. Use clipper on full beards.
IB-8789
08PG125
EXCITING ITEMS
FROM CONAIR
FORMULARIO DE PEDIDO PARA PARTES DE REPUESTO Y ACCESORIOS
Precios válidos hasta el 1ero de junio del 2009. Aceptaremos los pedidos después de esa fecha
y notificaremos los clientes si los precios han cambiado.
DESCRIPCIÓN NÚMERO PRECIO CANTIDAD TOTAL
Para evitar demoras, por favor escriba claramente. Necesitamos una dirección completa ya que UPS no puede hacer entregas en casillas postales.
NOMBRE__________________________________________________________________________________
DIRECCIÓN _________________________________________________ APTO. ___________ ____________
CIUDAD ___________________________ ESTADO __________ CÓDIGO POSTAL
TELÉFONO ( ) __________________________________
(sólo le llamaremos si tengamos alguna pregunta sobre su pedido)
Para información sobre otras partes de los conjuntos de Conair®, llame 1-800-3-CONAIR
Enviar a:
Conair Corporation Service Department
150 Milford Road
East Windsor, NJ 08520-9730
Incluya un cheque o giro postal a la orden de Conair (no podemos aceptar dinero en efectivo, estampillas, ni pedidos con pago con entrega). Los residentes de CT, IL, AZ y PA deben sumar al subtotal el impuesto estatal a las ventas que corresponda. Pedido mínimo de $10.00US o de lo contrario se sumará al pedido $2.00US por gastos administrativos. Todos los precios incluyen gastos administrati- vos y franqueo de envío. Los precios están sujetos a cambio sin previo aviso. Estos precios son válidos únicamente para los envíos en la parte continental de los Estados Unidos. La entrega demora entre 4 y 6 semanas.
CORTE AQUÍ
Subtotal
Impuestos a la venta*
TOTAL
Cuchilla inferior
Cuchilla superior
MODEL HCT300GB
Palanca reguladora ajustable
Botón encendido/ apagado
NUEVO
GMT400 SWITCHCUT
Juego de 12 piezas con recortadora para barba y bigote
• Dos cuchillas integradas
• Cambie las cuchillas al deslizar un botón
08PG125_hc300gb_IB.indd 208PG125_hc300gb_IB.indd 2 10/1/08 2:54:17 PM10/1/08 2:54:17 PM
Loading...