Conair CID110 User Manual

Service Center

©2003 CONAIR CORPORATION
7475 N. Glen Harbor Blvd., Glendale, AZ 85307

NLM055Y2 Printed in China

IB-4577B

Caller ID* Telephone
with 10-Memory Dialing

*You must subscribe to Caller ID service from your local
telephone company to receive Caller Identification.

HOTLINE [phone]

CID110 Owner’s Manual

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions
should always be followed to reduce the risk of fire, electric shock
and injury to persons, including the following:

1. Do not use this product near water, for example, near a bath
tub, wash bowl, kitchen sink or laundry tub, in a wet basement
or near a swimming pool.

2. Avoid using a telephone (other than a cordless type) during
an electrical storm. There may be a remote risk of electric
shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity
of the leak.

4. Use only the power cord and batteries indicated in this manual.
Do not dispose of batteries in a fire. They may explode. Check
with local codes for possible special disposal instructions.

SAVE THESE INSTRUCTIONS

LOCATION OF CONTROLS

1

2
3

4

5
6

7
8

9

1. Receiver

2. Receiver Volume Control

3. Hook Switch

4. Keypad

5. Tone/Pulse Switch

6. Redial Button

7. Transmitter / Mic

8. Store Button

9. Memory Button

10. New Call LED

11. Ringer Hi/Lo/Off Switch

12. LCD Display

13. Battery Compar tment

14. Review

15. Erase Button

16. Call Back Button

/ Button

CONGRATULATIONS!

You have purchased a CID110, Caller ID Telephone with 10­Memory Dialing manufactured to the highest standards of
ConairphoneTM. Before installing and operating, be sure to read

10

this manual.

GENERAL INFORMATION

11

12

13

14
15
16

UNPACKING

This package contains:

• CID110 Caller ID Telephone with 10-Memory Dialing

• Owner’s Manual

• Fully Modular Coil Cord

• Fully Modular Telephone Line Cord (Long Straight Cord)

• Fully Modular Telephone Line Cord (Short Straight Cord)

• Quick Installation Guide

• Impor tant Notice

• Two (2) Memory Index Labels

• Warranty Card

If anything is missing or damaged, contact the place of purchase.
Keep the packaging to transport telephone.

For your reference, keep a record of the date purchased.
Please save the sales receipt for the warranty reference.

Date of Purchase ___________________________

INSTALLATION INSTRUCTIONS

Follow these precautions:

a. Never install telephone wiring during a lightning storm.
b. Never install telephone jacks in wet locations unless the jack

is specifically designed for wet locations.

c. Never touch uninsulated telephone wires or terminals unless

the incoming telephone line has been disconnected at the
network interface.

d. Use caution when installing or modifying telephone lines.

123

TO INSTALL BATTERIES

Batteries are required for the Caller ID functions and Telephone
operations of the unit.

1. Open the battery door by pulling back the latch.

2. Insert three (3) AA alkaline batteries (not included).

3. Snap the battery door back into place.

Note: Once batteries are installed, you have 20 seconds to setup
the Caller ID.

SETTING UP YOUR CID110

DO NOT CONNECT the line cord to the wall outlet until the
Caller ID setup has been completed.

NOTES:

• If the Caller ID is not setup within 20 seconds after battery
installation, press and hold both the [ ] and [ ] keys for 4
seconds to activate the Caller ID setup.

• If you do not have the Caller ID service and want the time/
date set, please go to Caller ID setup section and ‘ENTER
TIME DATE’ setting.

The LCD shows ‘ENTER LANGUAGE’
followed by a choice of 3 languages
(English, Spanish, French).

The LCD then shows ‘ENG ESP FRA’.
NOTE: The ‘ENG’ is BLINKING. Press

] or [ ] to select ‘ENG’, ‘ESP’, or ‘FRA’.

[
Press [ERASE] to confirm.

If ENG is selected, the LCD shows ‘LCD
CONTRAST’.
Press [

] or [ ] to adjust five levels (from
1 to 5, default is 3) contrast of LCD.
Press [ERASE] to confirm.

If contrast is set, the LCD shows
‘ENTER AREA CODE’. The first digit
‘–’ of the area code will blink.

] or [ ] to enter the area code.

Press [
Press [ERASE] to confirm and go to next entry.
Repeat above steps until 3-digit area code is set.

456

If area code is set, the LCD shows
‘ENTER TIME DATE’.
Press [ ] or [ ] to select the hour digits.
Press [ERASE] to confirm and go to the next entry.

Press [ ] or [ ] to select the minute
digits.
Press [ERASE] to confirm and go to the
next entry.

] or [ ] to select the month digits.

Press [
Press [ERASE] to confirm and go to the
next entry.

Press [ ] or [ ] to select the date digits.
Press [ERASE] to confirm.

The LCD shows ‘TOTAL:00 NEW:00’,
which means both the total call and new
call counter are zero.

USING THE PHONE ON A DESK

1. Plug the long telephone line cord into the jack in the bottom
of the BASE, thread it through the groove toward the back of
the unit, then plug it into the modular phone jack.

2. Connect the COIL CORD to the jack in the HANDSET and
the BASE.

HANGING THE PHONE ON THE WALL

When the CID110 is wall mounted, the HANDSET GUIDE holds
the handset in place in the cradle.

On a wall phone plate

1. Plug the short telephone line cord into the jack in the base
bottom and into the jack on the plate.

2. Hang the base on to the two pins and pull the base down to
lock it on.

3. Plug the coil cord into the handset and base jacks.

On a wall without a plate

1. Install 2 screws with anchors into the wall, one above the
other, 3-1/4" apart, extending 3/16" out from the wall to hold
the base securely.

2. Install the long telephone line cord into the jack in the base,
thread it through the groove and plug it into modular wall
jack.

3. Hang the base on the screws and pull it down to lock it on.

4. Plug the coil cord into the handset and base jacks.

TELEPHONE FEATURES

Tone/Pulse Switch

Set switch to your type of service. If you don’t know whether you
have tone or pulse:

1. Put the switch on “Tone”.

2. When you have a dial tone, press any key on the keypad. If
the dial tone stops, leave it on “Tone”. If not, change the setting
to “Pulse”.

Receiver Volume Control

The receiver volume control is located on the side of the handset
of your phone. This enables you to adjust the receiver volume
from NORM to HI for a better listening level.

Ringer Off/Low/High

Your CID110 features a harmonic dual tone ringer that can be
adjusted from a loud (HI) to a soft (LO) sound level. When you
don’t want to be disturbed, slide the switch to the OFF position.
You can still make outgoing calls without being disturbed by
incoming calls.

Pause

Whether you have Tone or Pulse service, you can insert a 4­second PAUSE into the dialing or storing of a number into
memory in order to access custom and telebanking services,
long distance, etc. Press [Redial] at the desired point in the
number. Press [Redial] again if an additional 4 seconds is
needed.