Conair BE87CR User Manual

IMPORTANT SAFETY

INSTRUCTIONS

WHEN USING ELECTRICAL APPLIANCES, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS BEFORE

USING THIS MIRROR

DANGER– TO REDUCE THE RISK OF

ELECTRIC SHOCK: ALWAYS UNPLUG THIS MIRROR
FROM THE ELECTRICAL OUTLET BEFORE CLEANING.

WARNING– TO REDUCE THE RISK

OF BURNS, ELECTROCUTION, FIRE, OR INJURY
TO PERSONS:

1. Unplug from outlet before putting on or taking
off parts.

2. This mirror should not be used by or near children
or individuals with certain disabilities.

3. Use this mirror only for its intended use
as described in these instructions. Do not
use attachments not recommended by the
manufacturer.

4. Never operate this mirror if it has a damaged
cord or plug, if it is not working properly, if it
has been dropped or damaged, or dropped into
water. Return the mirror to a service center for
examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert an object into any opening.

7. Do not use outdoors.

8. Do not operate where aerosol (spray) products
are being used or where oxygen is being
administered.

9. To disconnect, turn all controls to the off position,
then remove plug from outlet.

10. Be sure mirror is not in a position where it can
reflect sunlight; reflected sunlight can cause fire.

11. Do not use on a soft surface such as a bed, where
openings may be blocked.

12. Touch mirror base until light shuts off, allow unit to

cool and unplug cord before replacing light bulbs.

13. Do not place or store mirror where it can fall or be

pulled into a tub or sink.

14. If mirror falls into water, unplug it immediately.

Do not reach into the water.

15. Never use while sleeping.

16. Do not use bulb greater than 30 watts.

Use in any 120 volt, 60 hertz AC electric outlet
(ordinary house current). Do not use it in any other
electrical outlet.

17. To protect against electrical hazards, do not use

while bathing or in the shower.

18. Unplug the mirror from outlet before cleaning.

Do not leave mirror unattended when it is
plugged in.

FOR HOUSEHOLD USE ONLY

SAVE THESE

INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Wall Mount Mirror

1. Remove mounting bracket from base or mirror.
Leave long screws in bracket.

2. Using 3/8" drill size, drill two holes in wall the same
distance apart as two opposite slots in
bracket. Screw into wall stud if possible. If drilling
into stud, use 1/
anchors in holes.

CAUTION: Do not drill into electrical wiring through
wall. Check with electrician if necessary.

3. Screw bracket onto wall, into the anchors.

4. Attach mirror to bracket by placing long screws
through the two holes in mirror’s base. Secure with
knurled nuts. Cord should be facing floor.

" drill size. Otherwise insert two wall

8

OPERATING

INSTRUCTIONS

To reduce the risk of electric shock, this furnishing has
a polarized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician
to install the proper outlet. Do not change the plug in
any way.

1. Your lighted makeup mirror features a 1x and 5x
magnification for the 8" mirror head.

2. Your lighted makeup mirror will adjust to many
different angles. Simply tilt the neck or head backward
or forward to adjust to the desired angle. Your mirror
will also swivel so that you can use either the normal,
flat mirror or the magnifying
mirror located on the opposite side.

3. Plug into any standard wall outlet (120 Volt AC). Turn
the rotary switch clockwise to the On
position.

4. After use, turn switch clockwise again to the
Off position.

TO REPLACE BULB

CAUTION: TURN OFF POWER AND UNPLUG. ALLOW
TO COOL AT LEAST 3 MINUTES BEFORE REPLACING
BULB.

NOTE: Do not use a bulb greater than 30 watts.

Contact a Conair service center at 1-800-3 CONAIR
for replacement bulb information (ask for replacement
bulb RP34). Bulbs are $1.50 each including shipping
and handling.

1. Unscrew screws from opposite sides of the mirror
housing near the rotating hinges (Fig. 1).

2. Carefully lift off the top half of the housing from the
bottom half that is affixed to the arm.

3. Unscrew the old bulb and replace with the
new bulb (Fig. 2).

4. Carefully replace the top housing half after locating
and aligning the screw holes to the bottom half. If the
holes don’t line up, turn top half of mirror 180˚.

5. Insert two screws back into screw holes and
tighten with screw driver. Do not over-tighten.

Figure 1

Figure 2

MAINTENANCE

Your lighted mirror is designed for household use
and is virtually maintenance-free. No lubrication is
needed.

If cleaning becomes necessary, disconnect the
appliance from the power source, allow to cool, and
wipe exterior with a damp cloth. Clean mirror surfaces
with a glass cleaner. To protect against electrical haz­ards, do not light until you are certain mirror is com­pletely dry.

If any abnormal condition occurs, unplug the lighted
mirror, allow it to cool, and return it to an authorized
service center for repair.

Handle cord carefully for to prolong its life; do not
jerk or strain at plug connections, or wrap cord
around mirror for storage. This could cause
damage to the cord and the mirror could short circuit.
To store mirror, coil cord loosely.

STORAGE

Disconnect from electrical outlet. BE SURE DIRECT
SUNLIGHT DOES NOT STRIKE MAGNIFYING SIDE OF
MIRROR WHEN LEFT UNATTENDED;
REFLECTED SUNLIGHT CAN CAUSE FIRE. Allow to
cool to room temperature before storing. Place in
cool, dry area out of reach of children, where it will
not be damaged.

WARNING:

IF YOU THINK THE

POWER IS OFF

WHEN THE SWITCH

IS OFF,

YOU’RE WRONG.

KEEP AWAY FROM WATER

Everybody knows that electricity and water are a dan­gerous combination. But did you know that an electrical
appliance is still electrically alive even if the switch is
off? If the plug is in, the power is on. So when you are
not using your appliances, keep them unplugged.

ALWAYS UNPLUG

SMALL APPLIANCES

Public Service AD from Association of Home Appliance

Manufacturers and Underwriters Laboratories, Inc.

LIMITED ONE YEAR WARRANTY

Conair will repair or replace (at our option) your
unit free of charge for 12 months from the date
of purchase if the appliance is defective in
workmanship or materials.

To obtain service under this warranty, return the
defective product to the service center listed below that
is nearest you, together with your purchase receipt and
$3.00 for postage and handling. California residents
need only provide proof of
purchase and should call 1-800-366-0937 for
shipping instructions. In the absence of a purchase
receipt, the warranty period shall be 12 months
from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS,
OR LIABILITIES, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTY
OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, SHALL BE
LIMITED IN DURATION TO THE 12 MONTH
DURATION OF THIS WRITTEN, LIMITED
WARRANTY.

how long an implied warranty lasts, so the above limita­tions may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE
FOR ANY SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES FOR BREACH
OF THIS OR ANY OTHER WARRANTY,
EXPRESS OR IMPLIED, WHATSOEVER.

states do not allow the exclusion or limitation of special,
incidental, or consequential damages, so the above
limitation may not apply to you.

This warranty gives you specific legal rights, and you
may also have other rights, which vary from state to
state.

©2005 Conair Corporation
Service Center

Conair Corporation
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307

Some states do not allow limitations on

Some

Illuminated Touch

Control Mirror

r

e

t

e

m

a

i

D

"

5

.

8

1x

/

x

ication

f

7

magni

Use and Care Guide

For your safety and continued enjoyment

of this product, always read the instruction

book carefully before using.

®

06PM8037 IB-7295

Model BE87CR